Search Documents

By M. E. Volin

The tungsten potentialities of the Combination mine were examined by a mining engineer of the Bureau of Mines in 1947. A report based upon his personal knowledge of the mine and the results of the examination contained recommendations for further investigation. This report presents factual data from Bureau of Mines field investigations begun in August 1947 and continued until December 1948, except for a 5-month recess during the first winter. The Combinat.ion mining property of 52 patented claims and 15 patented mill sites is in the Black Pine mining district, Granite County, Mont., 11 miles northwest of Philipsburg. The altitude in the mine vicinity is approximately 6,500 feet.

Jan 1, 1952

By G. D. Jermain

Exploration of the Antimony Peak district by the Bureau of Mines was conducted under the authority of the Strategic Minerals Act of 1939. Antimony was one of the seven metals designated at that time as strategic by the Secretaries of War, Navy, and Interior upon advice of the Army and Navy Munitions Board. As a result of many field examinations, the Antimony Peak property was chosen as one of the most attractive for the possible development of emergency antimony reserves. Exploration by the Bureau of Mines began in November 1940 and was concluded in May 1941.

Jan 1, 1949

By Kung-Lee Wang

This Bureau of Mines study illustrates the economic significance of the Florida phosphate industry to the State and to the Nation. Environmental considerations related to phosphate industry activity are discussed briefly. Based on forecasts of Florida phosphate production in 1975, and using 1972 dollars, regional and national output value, income, and employment created by the phosphate industry were estimated for 1975. State and Federal government tax revenues generated by the phosphate industry, are also measured. Further, the concentrated impact of the phosphate industry on certain Florida areas and on regional industries is examined. Finally, the phosphate industry's importance to the U.S. balance of payments, U.S. agricultural production, and the Frasch sulfur industry is considered, in addition to byproduct fluorine, and potential byproduct uranium from fertilizer manufacturing.

Jan 1, 1974

By Marvin W. Wilson

The Federal Bureau of Mines has conducted laboratory experiments simulating underground gasification of coal to study the feasibility and mechanism of the process and determine the chemical and physical characteristics of a coal-bed during gasification. Laboratory and small-scale field experiments also were made to investigate the properties of coal and other factors affecting the electrolinking-carbonization method of preparing a path through a coalbed before gasification. Laboratory experiments simulating underground gasification of coal: Experiments with a laboratory retort indicated that bituminous-coal deposits could be gasified in place to produce a combustible gas.

Jan 1, 1960

By Neil B. Young

Carbonate minerals constitute a major fraction of the oil shale in Colorado's Green River Formation. Quantification of carbonate minerals is important for the characterization of oil shale, particularly because of their thermal activity in production of oil from shale. The carbonate minerals found in this oil shale are nahcolite (NaHCO3), dawsonite [NaA1(OH)2CO3], dolomite [(Mg1-xFx)Ca(CO3)2], calcite (CaCO3), and ferroan [(Mg1-xFex)CO3]. Although carbonate minerals can be removed by acid extraction from the balance of the oil shale, direct determination of carbonate minerals is complicated by the occurrence of the same cations in more than one mineral. A method for assigning the acid-soluble cations to the individual carbonate minerals was developed from two assumptions based on oil shale geochemistry: (1) Calcite and ferroan do not occur together, and (2) the ratio of iron and magnesium is the same in dolomite and ferroan. These assumptions were tested by the Bureau of Mines by applying the technique for assigning cations to 219 samples from the saline section of the formation. The reported carbonate mineral amounts were compared statistically with X-ray diffraction peak heights, verifying the cation assignment method.

Jan 1, 1975

By James P. Bennett

The Bureau of Mines investigated the effect of refractory oxide additions, introduced in soluble form, on the high-temperature properties of 90- and 98-pct-MgO brick. Brick samples were soaked in solutions containing Al, Ca, Cr, Co, Fe, Mg, Mn, Mo, Ni, Si, Sr, Sn, Ti, or Zr ions. Additions to 98-pct-MgO brick did not generally result in statistically significant property improvements. Statistically significant improvements were noted in hot modulus of rupture (MOR), slag resistance, and spalling resistance of the 90-pct-MgO brick for additions of Al, Mg, or Sn. High-temperature performance of treated 90-pct-MgO refractories was equal to or approached that of 98-pct-MgO brick. The marked improvements due to tin were obtained with additions of only 1.14 wt pct Sn02.

Jan 1, 1985

By R. D. Leitch

Spontaneous firing of coal during storage end even during shipment has long been a serious problem, especially in some regions and with some coals, and methods for preventing such firing have been investigated at intervals for more than 70 years. Spontaneous or other firing of coal waste, either outside or inside mines, has also been a problem probably for as long as mining has been practiced extensively. Much trouble has been caused by such fires, and much money has been spent in attempts to extinguish them. It is known generally that surface waste banks in bituminous-coal fields are very likely to take fire sooner or later, but it is not known so generally that anthracite refuse-bark fires also are common and that at least some of them are more serious in their effect and results than being regarded merely as a nuisance. There surface refuse fires probably would have attracted much more than local attention long ago had it not been that they usually cause no more serious trouble than air pollution. A few supposedly effective methods of preventing or extinguishing spontaneous fires have been reported rather recently. Unless one or more of these prove to be widely applicable, methods of solving these problems are no more certain today than they have been for many years.

Jan 1, 1940

By D. B. Dow

The appearance of water in an oil field is the forerunner of various difficulties, and probably represents the greatest technical problem that the producer must face. Water conditions bear-directly on the quantity of oil recovered, and the length of the life of a field. Presence of mater increases the cost of operation, for example, gifting costs. On account of the corrosive action of oil-field waters on pumps and other equipment, frequent replacement of equipment is necessary. Furthermore, water may affect the marketability of the oil produced, as detrimental emulsions of water in oil (?B.S.?, "cut oil", etc.) are often formed. The writer has recently completed a study of oil-field emulsions. The present paper deals with the factors responsible for the formation of emulsions. This will be followed by another dealing with methods now utilized for dehydrating oil-field emulsions, and by a third dealing with the physical chemistry involved in the formation and resolution of such emulsions.

Jan 1, 1925

By A. C. Smith

The U.S. Bureau of Mines developed an experimental method to evaluate the relative effectiveness of water additives on the extinguishment of coal fires. The experiments were conducted in the fire zone of the multiple-entry section of the Bureau's Bruceton Experimental Mine. Four-hundred-pound Pittsburgh Seam coalbeds were ignited and allowed to burn until well-developed fires were achieved. Extinguishing agent-water solutions were then applied to the fires, and the quantity required to extinguish the fires was compared with the quantity of water alone required to extinguish similar fires. A 20% diammonium phosphate-water solution required an average of 5.8 gal to extinguish the coal fires, while two commercially available additive-water solutions required an average of 8.1 and 8.0 gal, respectively. The average amount of water required to extinguish the fires was 7.4 gal. An analysis of covariance, using the thermal energy of the coalbed to quantify the fire at the time of extinguishment, showed that the diammonium phosphate-water solution was slightly more effective at extinguishing these coal fires than water alone, and the two commercially available additive-water solutions were statistically equivalent to water alone.

Jan 1, 2010

By V. A. Marple, K. L. Rubow, Y. Tao

"A personal diesel exhaust aerosol sampler has been designed and evaluated in both laboratory and field settings. The sampler uses size selective sampling for the determination of the respirable mass concentrations of mineral dust and diesel exhaust particulate matter found in underground coal mines. This design is based on the premise that diesel exhaust particulate matter is predominantly less than 0.8 um while mineral dust is greater than 0.8 gm. Operating at a flow rate of 2 L/min, the sampler consists of a 10 mm Dorr-Oliver respirable dust cyclone followed by an 0.8 gm cutpoint impactor and an afterfilter. Field evaluations consisted of sampling at 6 different locations in these underground coal mines. Measured aerosol concentration less than and greater than 0.8 um have been compared with a well characterized cascade impactor.Techniques must be developed for measuring the mass concentration of diesel exhaust particulate matter found in underground coal mines due to the health concerns associated with worker exposure to diesel exhaust particulate matter. Diesel exhaust particles are in the respirable size range and have been regarded as a potential occupational carcinogen by NIOSH (1988). Furthermore, a 1988 MSHA advisory committee directed MSHA to develop a sampling protocol for assessing worker exposure to diesel exhaust particles.The University of Minnesota and the Bureau of Mines, over the past 4 years have measured the size distribution of diesel exhaust particles and mineral dust, both in the laboratory and underground mines (Cantrell, 1987; Cantrell et al., 1987; Cantrell and Rubow. 1988; Marple et al, 1986; Rubow et al., 1988: and Watts et al., 1989). To date, measurements have been made in nine coal mines. Seven mines utilized diesel-powered equipment at the mine face while two used electric-powered equipment. The results of these field tests indicate that mineral dust and diesel exhaust particles can be differentiated on the basis of particle size. The measured particle size distributions have been found to be bimodal with a saddle point at 0.8 um. This has led to the hypothesis that one method for measuring worker exposure to diesel exhaust particles would be to collect size fractionated particle samples separated at 0.8 um with the diesel particles being less than 0.8 um and the mineral dust particles greater than 0.8 um.Aerosol size distribution measurements, using a micro-orifice uniform deposit impactor (MOUDI), have been conducted in the mine intake air portal, intake entry to the working section, haulageway, and section return entry. The MOUDI is a ten stage cascade impactor with particle cutpoints ranging from 0.1 to 15 um aerodynamic diameter (Marple and Rubow. 1984b; Marple et al., 1989). The sampling flow rate is 30 L/min."

Mar 1, 1992

By E. J. Lintner

This paper is one of a series being prepared by the United States Bureau of Mines describing gypsum mining and crushing methods and costs at various operations throughout the United States. These papers are designed to disseminate technical information regarding methods used. The cost tabulations represent local operating expenditures only and not total production costs. It is recognized that publication of total production costs may in many instances cause embarrassment to individual operators as well as to the industry as a whole. On the other hand, operating costs are essential to a technical discussion and study of the methods employed. The attention of the reader is called specifically to this differentiation so that there may be no misunderstanding of the scope of the cost tabulation. This paper deals specifically with the mining and crushing methods employed by Victor Plaster, Inc., Victor, Ontario County, N. Y. The maximum annual production capacity of this company is 150,000 tons of crushed gypsum. The methods and practices employed arc typical of those followed in the gypsum mines in western New York State. The shaft is, perhaps, the deepest and the thickness of the gypsum mined is above the average for the section.

Jan 1, 1937

By Constantine C. Popoff

"INTRODUCTION AND SUMMARYDuring 1946 several high-grade limestone deposits in western Washington were examined by the Bureau of Mines. This report presents the data obtained from investigation of the Sauk Mountain deposits in east-central Skagit County, Washington.The investigation consisted of transit and topcgraphic surveys and sampling. The areas selected for sampling were first cleaned by blasting; channel samples up to 40 pounds were cut where practical. Chip samples averaging 30 pounds were taken where channel samples could not be cut. A total of 21 samples in the Sauk Mountain area were taken and. analysed. The locations of the samples are shown in figures 2 and 4, and the analyses are listed in tables 1 and 2. This investigation is a part of a long-range program of general investigation of mineral resources for future industrial development of the Pacific Northwest. The Sauk Mountain deposits were investigated for the purpose of disclosing now sources of high-purity limestone, which could be mined and shipped at low cost to Seattle and other industrial cities in the Pacific Northwest."

Oct 1, 1948

By M. B. Cooke

An analytical method for the determination of the gum-forming material in gasoline has been developed by the Bureau of Mines, during a study nor in progress to determine the best rays for elimination of such constituents from gasoline. This method is similar in principle to that previously described by Smith end Cooke,2 which involved evaporation of e sample of gasoline in a small glass dish. The evaporation was started on an actively boiling steam bath and completed in an air oven at 105°C. In the improved method described below, the stem bath has been replaced by a steam heated oven in which an inert atmosphere is maintained. Air is excluded from the oven, consequently the precision of the determination is increased. Furthermore, evaporating dishes different from those previously described may be used.

Jan 1, 1925

By Rudolf E. Greuer, Linneas W. Laage, Xinton Chang

UNIT OF MEASURE ABBREVIATIONS USED IN MFIRE FT foot FT3/MIN cubic foot per minute LBM•MIN2/FT4 pound mass times minutes squared over feet to the fourth FT2/HR square feet per hour BTU/HR*FT*F British thermal unit divided by hours times fimes feet times degree Fahrenheit IN W G inches water gage FT3/MIN cubic feet per minute FT2 square feet FT3 cubic feet LBM, pound mass F Fahrenheit IN W G /CFM2 inches water gage per cubic foot per minute squared PERCENTAGE percent BTU/MIN British thermal unit per minute MFIRE BAT PROGRAM cls echo off echo MFIRE activated mfire0 echo Wait a moment for loading the program if EXIST zheng chg mfirel if EXIST zheng chg mfire2 if EXIST zheng chg mfire1 if EXIST zheng chg erase zheng chg if EXIST hang chg erase hang chg if EXIST yunzhi fan copy yaodong.ion+yunzhi fan yaodong ion if EXIST yunzhi fan erase yunzhi fan if EXIST xintan chg copy yaodong xin+xintan chg yaodong ion if EXIST xintan chg erase xintan chg if EXIST yaodong xin copy yaodong.xin mfire out if EXIST yaodong.xin erase yaodong.xin if EXIST net erase net echo Your output is saved in file MFIRE OUT MFIRE0 FOR PROGRAM CHARACTER•50 A OPEN (10,FILE='NET',STATUS='UNKNOWN',FORM='UNFORMATTED') NETWW=0 WRITE (10) NETWW OPEN (21,FILE='ZHENG CHG',STATUS='UNKNOWN',FORM='UNFORMATTED') A=) ' B=0.0 WRITE (21) A WRITE (21) A,B

Jan 1, 1990

By David Montgomery

The feasibility of building a calibrator for the DuPont D-100 audio dosimeter is discussed. The desired specifications are used as guidelines but the possibility of their relaxation is also considered. Commercially available equipment is surveyed and found to not satisfy the guidelines. Several alternate concepts are investigated, and recommendations for further work are presented.

Jan 1, 1974

Major activities of the Bureau of Mines Explosives Research Center during fiscal year 1965 (July 1, 1964, to June 30, 1965) are reviewed briefly. Part 1 summarizes significant accomplishments of the projects that were active during the report period. Part 2 presents short abstracts of the publications that appeared in the Bureau series and in other media during fiscal year 1965. Publications issued after June 30, 1965 are noted where pertinent in footnotes but are not abstracted. ACKNOWLEDGMENTS The Bureau of Mines gratefully acknowledges the support given through cooperative agreements by the following organizations to investigations con¬ducted by the Explosives Research Center during fiscal year 1965: Dow Chemical Company Manufacturing Chemists' Association Monsanto Chemical Company The Sulphur Institute

Jan 1, 1966

By S. L. McGill

The U.S. Bureau of Mines has determined the microwave heating rates for a suite of minerals and reagent-grade compounds. Maximum temperature achieved for the samples and the time required to reach temperature are reported. Heating rates of powdered samples are presented as a function of incident powers up to 3,000 W at 2,450 MHz. Descriptions of the microwave cavities, test cells, and a thermocouple assembly used to measure temperature in the microwave field are given. Many minerals of value heated in the microwave field, whereas host rock or gangue materials did not. In general, heating rates increased as incident power was increased. Exceptions to this were some very good (CuO, Fe304, and PbS) and very poor (CaC03 and SiO2) microwave-absorbing materials that showed negligible changes with increased power. Applications demonstrating the use of microwave energy in mineral processing that are described herewith include oxidation-reduction reactions, mineral liberation, and mercury retorting-vaporization. Microwave data on mineral heating rates will provide insight to possible chemical and mineral processing applications as well as assist in predictions of processing parameters.

Jan 1, 2010

By T. M. Romslo

"The Keystone and St. George properties are in the so-called Johnson Camp area and adjoin a property that in recent years has become a steady producer of low-to medium-grade copper-zinc ores. The Keystone Copper Co. was active intermittently from 1908 to 1938 and during 1926 to 1937 produced a recorded 1,100 tons of 5 percent copper ore. There is no evidence that ore has been produced from the St. George property.In the Johnson Camp area both igneous and sedimentary rocks ranging in age from pre-Cambrian to Quaternary are exposed. The ore bodies are in the Paleozoic rocks and occur principally in the Abrigo formation, which is composed mainly of limestones and shales. The rocks of the productive zones are metamorphosed and are cut by systems of fractures and faults. Chalcopyrite and sphalerite, the principal ore minerals, replace altered limestones to form deposits locally called mantos and chimneys.Investigation of the Keystone and St. George deposits by the Bureau of Mines included topographical and geological mapping of the surface and the underground workings and diamond drilling from the surface. A total of 10,067.8 feet was drilled in 22 holes. The drilling started November 13, 1947, and was completed August 19, 1948.This report records factual information obtained during the course of the investigation."

Jul 1, 1949

By N. C. Tomoeda, W. D. Bensema, J. W. Adams

Measurements of surface magnetic field noise were made at various locations over the Geneva Coal Mine near Price, Utah, on June 12, 1973. The locations selected were on the surface over emergency locator beacons underground at depths between 350 meters (1150 ft .) and 488 meters (1600 ft .) . The surface terrain where these measurements were made was mountainous, and access was difficult. There were no power lines within several miles, and the weather was clear; therefore, the magnetic noise levels were about as low as will normally occur. Results of measurements of distant sferics indicate rather sharp cutoff frequencies below which broad- band, impulsive noise is attenuated. The mechanism of propagation for this noise above the daytime cutoff frequency of 3500 Hz and the nighttime cutoff frequency of 1700 Hz is deduced to be a waveguide formed by the D or E layers of ionosphere as an upper plane and the earth as a lower plane. The measurement systems used are similar to those used earlier. The technique is to record broadband, analog signals, digitize the data, and use a fast- Fourier transform to obtain spectral plots. This tech- nique is novel in that it can measure simultaneously all magnetic field energy within a limited portion of the spectrum for a limited time, and, after processing, reproduce the events occurring in that time interval in great detail .

Jan 6, 1974

By R. D. Currie

"INTRODUCTION Compressed air for operating coal-mining equipment is seldom considered in conjunction with modern methods and appliances. But the Jamison Coal & Coke Co. has proved the economy and efficacy of compressed air for this purpose at its Mine 8 near Farmington, 8 miles west of Fairmont, Marion County, W.. Va., and the mining industry as a whole concedes its superior safety in gassy or dusty coal mines.The uses for compressed air in coal mining are now generally associated with such equipment as coal punchers, chain-breast machines, and to a lesser extent the ""radialaxe"" type of mining machines.Electricity has rapidly superseded compressed air for power in coal mines during the past 20 years; and in the last few years the general, and often unwise, use of electricity at the face region has taken on added impetus through the widespread use of mechanical loading equipment.Some of the unfavorable results of this increased use of electricity are shown in the growing number of mine explosions and fires of electrical origin. In the past four years 59 explosions of this type took the lives of 672 men, or 74.8 per cent of the total number of deaths from explosions were due to explosions of electrical origin.3In 1926, an explosion in Mine 8 of the Jamison Co. killed 19 men. The exact source of ignition was not determined, although it was definitely decided that it was of electrical origin and probably was at an electric coal-cutting machine.Prior to this disaster the company had done some experimenting with compressed-air-driven mining machines, and its Mine 9 had been completely equipped with air-driven chain-breast machines; a few of these machines were also in use in Mine 8. The explosion, however, gave impetus to the adoption by this company of compressed air for operating face equipment. The chain-breast machines were as satisfactory as electric machines of the same type; but the trend in the industry was toward faster cutting machines, which required less physical exertion on the part of the operating crews. A track-mounted machine of the arcwall type was found to be suitable for the conditions and system of mining, so that one of these operated by compressed air was developed by the Jeffrey Manufacturing Co. working with the officials of the Jamison Co.The first of these machines was installed in the latter part of 1926 and additional machines were delivered from time to time, until at present there are nine of them in the mine. Necessary improvements have been made, with the result that a fast-cutting, easily handled, efficient, and safe mining machine has been developed for cutting the hard Pitts¬burgh bed coal of the Fairmont field."

Oct 1, 1932