Search Documents

By Herbert H. Einstein

The thrust of research reported in Part I was to collect in-situ data from exploration programs and the published literature, and to empirically establish distributional patterns for these variables. Since discontinui¬ties in a rock mass govern to a large extent its engineering properties and thus the performance of any slope in the mass, work has been devoted to determining the appropriate distributional forms for attitude spacing and length of discontinuities and to distributional properties of resis¬tance and deformability parameters. The conclusion from these analyses is that trace lengths are logNormally distributed and that joint spacing is Exponentially distributed, regardless of orientation of the sampling line, and regardless of whether each joint set is considered separately or not. Joint orientation (attitude) data representing 22 individual joint sets from eight sites (a total or approximately 20,000 joints), do nor strongly support any of the commonly used distributions as broadly applicable in practice. The autocorrelation )f geometric joint properties is also examined. However, no significant spatial correlation could be found even after extensive data manipulation. The investigation of resistance and deformability parameters starts with a review of mechanisms and models that are used to represent them. Review and statistical evaluation of approxi¬mately 2,000 discontinuity shear tests has shown that good statistical estimates for use in reliability analyses can be obtained for friction angles.

Jan 1, 1979

By Beverly W. Dunning

The effect of vacuum melting on the elimination of gases and nonmetallic inclusions for six low-alloy steels was investigated. The purpose of these studies was the analysis and comparison of differences in gas content and inclusions in air-melted and vacuum-melted steel. Data obtained from melts of 1-1/4 to 20 pounds indicate that vacuum melting decreases the number and size of nonmetallic inclusions and at the same time increases the degree of dispersion of the remaining inclusions. These improvements are undoubtedly related to the elimination of approximately 80 percent of the nitrogen and 90 percent of the oxygen as well as most of the undesirable metallic trace impurities.

Jan 1, 1961

By J. H. Stears

Increasing use of Birmingham and other roof trusses prompted a Bureau of Mines study of support forces produced on a mine roof by these members. Equations, obtained from laboratory and field tests, are given for calculating the contact forces between the roof strata and a typical truss. Actual contact forces for a specific truss are difficult to estimate because of variable friction loss at the contact points. A finite-element analysis, using typical contact forces, indicated that trusses have a negligible effect on the stress field in massive, competent roof strata. The effectiveness of trusses in supporting broken rock strata was not analyzed. However, experience has shown that trusses are effective in supporting incompetent roof.

Jan 1, 1988

By David L. Veith

Caustic scrubbing followed by silica flotation with cationic ether primary amine proved effective in upgrading commercial magnetic concentrates to supergrade products containing 2 percent SiO2, or less. Samples representing 41 million long tons per year of commercial magnetic concentrates from the Lake Superior region were tested by the Bureau of Mines. Bench-scale and pilot plant research indicated an estimated potential of 32 million long tons per year of superconcentrates to be available. Two pilot plant investigations yielded superconcentrates containing 1.1 and 1.9 percent SiO2 that were derived from commercial concentrates containing 7.0 and 4.2 percent SiO2, respectively. Corresponding iron recoveries were 90 and 93 percent at reagent costs of just over 33 cents per long ton of superconcentrates produced. Additional sources evaluated on a bench scale resulted in iron recoveries of 72 to 95 percent in products containing 1.7 to 2.0 percent Si02. Although reagent cost ranged up to 60 cents per long ton of superconcentrate, it is probable that these costs would be reduced in plant applications where benefits are derived from material and reagent recycle.

Jan 1, 1974

By Alla D. Mah

The heats of combustion of three chromium carbides, Cr23C6, Cr7C3, and Cr3C2, were determined by combustion calorimetry. Heats of formation calculated from the results follow: ?Hf°298 (Cr23C6) = -94.7 ± 5.0 kcal/mole, ?Hf°298 (Cr7C3) = -43.3 ± 1.7 kcal/mole, and ?Hf°298 (Cr3C2) = -22.5 ± 0.8 kcal/mole.

Jan 1, 1969

By John W. Adams, W. D. Bensema, Motohisa Kanda

Two different techniques were used to make measurements of the absolute value of electromagnetic noise in an operating coal mine, Robena No. 4, located near Waynesburg, Pennsylvania. One technique measures noise over the entire electromagnetic spectrum of interest for brief tine periods. With present instrumentation, the spectrum can be covered from 40 Hz to 400 kHz. It is recorded using broad-band analog magnetic tape, and the noise data are later transformed to give spectral plots. The other technique records noise envelopes at several discrete frequencies for a sufficient amount of tine to provide amplitude probability distributions. The specific measured results are given in a number of spectral plots and amplitude probability distribution plots. The general results are that at frequencies below 10 kHz, power line noise within the mine is severe. Impulsive noise is severe near arcing trolleys, and at lower frequencies near any transmission line. Carrier trolley phone signals and harmonics are strong throughout the mine whenever the trolley phone is in operation. Additional information beyond that included in this report may be obtained from the authors, who are with the Electromagnetics Division of the National Bureau of Standards.

Jan 4, 1974

By D. R. Hanson

This Bureau of Mines study examines the acoustic vibrational spectra of rock slabs in the range of 0 to 5,000 Hz. The power spectra of so-called drummy rocks were found to be diagnostically enhanced in the range of 200 to 1,000 Hz. Comparison of the power in this band with that in a band from 3,000 to 3,500 Hz provides a quantitative measure of rock stability. A prototype field instrument was designed, constructed, and field-tested. This battery-powered instrument computes the power contained in the two frequency bands mentioned, compares the magnitude of these two quantities, and displays a number that is related to the detachment of the block tested. Field tests show that this instrument is capable of giving reliable measurements of block stability under conditions of noise and dust that would seriously degrade the accuracy of normal sounding techniques.

Jan 1, 1985

By E. A. Rowe, G. H. Keith, B. D. Jones

An evaluation of electrowon tungsten powder was made by comparing its characteristics with conventional hydrogen - reduced tungsten powder . Electrowon tungsten powder was investigated with respect to particle size and shape , apparent density , flow rate , compressibility , green strength , and sintering characteristics . In addition , its chemical purity , absolute density , and purification by melting were determined . Significant findings were higher flow rates and better compressibility than hydrogen - reduced tungsten powder . However , the large particle size peculiar to the electrowinning process effectively prevented conventional sintering to a high- density material . The possibility of producing high - density material , using a new technique of hot swaging sheathed sintered - tungsten compacts , was demonstrated by the achievement of densities of 92 percent of theoretical .

Jan 1, 1965

By S. J. Page, P. Bolsaitls, W. E. Wallace, C. A. Hill, M. J. Keane

"Boiling respirable quartz dust in water for 10 to 40 minutes decreases the cytotoxicity for both erythrocyte hemolytic potential and pulmonary macrophage release of lactate dehydrogenase in vitro. The potential is reduced to near zero in the boiling concentration range of 1 to 10 mg quartz per ml water in boiling times of 20 to 40 minutes. Below this range the detoxification occurs over a longer boiling time. Above this range the hemolytic potential remaining after 40 minutes of boiling approaches native quartz potential with increasing concentration up to 30 mg quartz per ml water. Replacing the media with fresh at the midpoint of boiling results in full detoxification through 20 mg per ml. Pre—boiling the medium with quartz or silica gel reduces the effect of subsequently boiling test samples. Detoxification persists after mild drying at 110 C for 8 hours, and persists after three days of resuspension in water at room temperature. Additional data on persistence of the effect, on the use of acidic and basic media treatment, and on surface analyses are presented, with a discussion of a working hypothesis and research needs.IntroductionResearch underway to determine interactions of quarts and other mineral dust surfaces with pulmonary fluids and alveolar macrophages in culture led to the observation that when dusts were autoclaved in aqueous suspension, their cytotoxic effects on macrophages wore suppressed, in some cases fully and even after several days incubation with the cells. This finding was in direct contradiction to earlier results from both short term macrophage lysosaal enzyme release assays, as well as longer term cytotoxicity assays from macrophages in culture; in those studies, dusts were steam autoclaved at 121 121 ºC with no liquid water but with steam present. (1,2) However detoxification under boiling conditions has been reported in other research.(3). It was decided to use the hemolysis assay to further investigate these findings, because of its sensitivity, simplicity and cost."

Jan 1, 1988

By R. V. Holmes

The properties of the Colorado Copper Co. in Sinbad Valley, Mesa and Montrose Counties, Colo., were rehabilitated and sampled by the Bureau of Mines in October, November, and December 1942. The several deposits were reexamined in March and April 1945 to obtain information disclosed by company work after December 1942. The development program included surface trenching, rehabilitation of several edits, and channel sampling of the exposures. Assay determinations wore made on 204 samples from the surface and underground workings. The results are given in the appendix. Several copper deposits in the Sinbad Valley area are similar in origin. The host rocks are sedimentary and mice in age from Pennsylvanian to Cretaceous. The Colorado No. 3 deposit occurs in the Cutler formation, which consists of many small lenses of conglomerate, sandstone, and shale. Mineralization is closely associated with faulting. On the Pyramid group the enrichment occurs in a zone of fracturing and jointing end also spreads into the adjoining sandstone. The ore deposition on the Copper Rivet claim is associated with a fault zone and is confined to en area above the contact of the Dolores-Wingate formations. Mineral deposits on the Sinbad claims occur at intersections of faults with blue-gray Pennsylvania limestone. Copper enrichment occurs along faults and as replacement of the surrounding limestone. Metallurgical tests indicate that ores from the Colorado No. 3 and Pyramid claims can be treated successfully by leaching with sulfuric acid. This method cannot be applied to ores from the Copper Rivet or Sinbad deposits because of high calcite content. Flotation tests at Boulder City, Nev., showed a recovery of less than 60 percent with a 14.24 percent copper concentrate.

Jan 1, 1952

By J. R. Koehler

Effective barrier pillar design is essential for safe and productive underground coal mining. This U.S. Bureau of Mines report presents an overview of available barrier pillar design methodologies that incorporate sound engineering principles while remaining practical for everyday usage. Nomographs and examples are presented to assist in the determination of proper barrier pillar sizing. Additionally, performance evaluation techniques and criteria are included to assist in determining the effectiveness of selected barrier pillar configurations.

Jan 1, 1995

By Charles B. Carpenter

When a drilling well strikes a horizon in which there is a large volume of petroleum or natural gas under high pressure, danger of a blowout with disastrous results is imminent unless proper precautionary measures are taken. The history of oil-swell drilling has been marked by many blow-outs and wild wells, some of which-have caught fire and burned for long periods. Such incidents nearly always make headline news, but ordinarily few persons realize that what to them is an interesting newspaper item may entail great financial loss to the operator and frequently loss of life or personal injury to members of the drilling crew and others in the vicinity of the well. The blow-out, wild well, and crater are dreaded specters to every thoughtful person in the oil industry because of danger to life and property, underground damage to surrounding wells, dissipation of reservoir energy, and waste of irreplaceable natural resources that blow to the air or migrate to barren formations. Every operator drilling in high-pressure fields must be on the alert always to forestall any conditions that may lead to a blow-out, and his vigilance must not cease until a well is completed and oil, gas, or both are flowing to storage or market.

Jan 1, 1937

By C. W. Schultz

The vapor pressure of manganese in equilibrium with a series of liquid iron-manganese alloys was determined by the carrier gas method over a broad range of alloy composition. From these data the activities of manganese in the iron-manganese system were calculated. The system appears to be ideal.

Jan 1, 1966

By Robert E. Wallhagen

The froth foam seal topping system is part of a system for remote sealing of mine passages using flyash transported pnuematically from the surface. Making the final 5 percent of the seal with a foamed-in-place fire retardant polyurethane reduces the required flyash volume by 50 percent and provides a more reliable seal. Foam components are held at the surface under proper conditions of temperature and pressure; then conveyed down the borehole through individual hoses and mixed at the bottom with a static mixer. The polyol component is pre-mixed with fluorocarbon-12 which, when released from system pressure in the mixer, boils and causes the foam to expand. Difficulties in handling this particular foam formulation are offset by a flame spread index well below the 25 level by ASTM E-162 normally required for under-ground applications. Isocyanate, polyol (TDI) and catalyst are conveyed to the downhole package by three separate lines. Five additional lines operate the valving and convey solvent so that the mixer and package lines can be flushed immediately after foaming. The eight-hose bundle is provided in segments of several lengths so that bore-hole depths can be matched. Cast-in-place plastic cylinders hold the bundle together and transfer the weight of the hose through a special quick-release clamp to the crane's wire rope. The downhole package and hose bundle are deployed using a specially designed winch and crane system capable of borehole deployment to 1500 feet.

Jan 1, 1977

By Deno M. Pappas

The purpose of this Bureau of Mines study of U.S. roof and rib (roof- rib) accident statistics and related accident costs is to define current accident trends (1980-84) associated with fatal and nonfatal roof-rib fall accidents. Data were retrieved from a data base containing all recorded U.S. mining accidents, then sorted and normalized utilizing a computer software program. The statistics indicate that roof-rib accidents have significantly declined in the 5-yr study period. Moreover, they indicate that there have been increases and/or patterns of roof-rib accidents associated with specific mine characteristics, such as seam height, mine size, geographic location, and seasonal variations. Also, roof-rib injury characteristics produced pattern changes involving worker activity, lost workdays, types of injury, and severity of injury. A conservative estimate indicates that there has been a 30% adjusted increase in the cost of a roof-rib accident over the 5-yr study period.

Jan 1, 1987

By B. W. Madsen

Research by the Bureau of Mines has shown that treatment of open pit waste by crushing and sizing followed by flotation of the fines and leaching the coarse fraction results in greater metal recoveries than obtained by leaching only. Tests with a chalcocite-bearing quartz monzonite mine waste sample that had been crushed to minus 6 inches and screened on 1/2 inch yielded copper and silver recoveries of 71 and 22 percent, respectively, by the combined flotation-leaching process, compared with 48 percent of the copper and no silver recovered leaching the run-of-mine material. Copper was more readily leached from the coarse material with the minus 1/2-inch fines removed than from material with the fines included. The improved leaching was attributed to improved permeability and the associated improved circulation of air to the interior of the ore column. Cost estimates showed that the proposed intensive treatment of mine waste will require a greater capital investment and higher annual operating costs than conventional milling and dump leaching process. However, the income from the additional metal production offsets the increase in capital investment and operating costs, resulting in additional profit.

Jan 1, 1975

By B. T. McClure

Oxidizing catalytic converters are sometimes used by underground mine operators as an emission control device to reduce odor, hydrocarbon (HC), and carbon monoxide (CO) emissions from diesel equipment. The objectives of this report are to quantitatively assess the effects of catalytic converters on diesel exhaust emissions and to make recommendations for their use. Information in this report is from a literature survey and contract research supported by the Bureau of Mines. Catalytic converters are effective in reducing CO, HC, and odors when the exhaust temperature is high enough so that the converter remains above 250° C. Converter temperature is dependent upon engine duty cycle. Catalytic converters increse sulfate emissions and slightly in- crease oxides of nitrogen (NOx) emissions. If low sulfur fuels are not used, the increase in sulfate and nitrogen dioxide (NO2) emissions can offset any advantages of the catalytic converter as measured by the emissions quality index (EQI). In addition, in vitro bioassays have shown that catalytic converters produce soluble organic compounds, which have increased mutagenic activity with respect to untreated exhaust. Based upon criteria recommended by a joint Canadian-United States research panel, catalytic converters should only be used in special circumstances in underground mines. Vehicles equipped with catalytic converters should operate under moderate to heavy load conditions, and use fuel with a sulfur content less than 0.1 pct.

Jan 1, 1988

By A. A. Cochran

Bureau of MinesThe Bureau of Mines studied the development of practical methods for recovering manganese from the extensive domestic resources of low-grade ores and open hearth slags. A one-step operation was developed on a laboratory scale in which manganese and iron compounds are treated with chlorine, volatilized, and separated by selective condensation. Manganese recoveries of 90 to nearly 100 percent were obtained from 9 of the most important domestic ores. Analyses of the manganese chloride product indicated that it was suit-able for aqueous electrolysis with little additional purification. A complete, integrated process that provides for the recovery and recycling of chlorine is proposed. This process appears to have distinct advantages over previously proposed manganese recovery processes, and, in sharp contrast to leaching procedures, it is applicable to practically any manganese-bearing material.

Jan 1, 1967

By B. W. Gandrud, G. D. Coe

"INTRODUCTION The Southern Experiment Station of the U.S. Bureau of Mines, cooperating with the University of Alabama and Alabama coal producers, has made a series of investigations of the washability of coal from commercially important bens of Alabama. The results of 13 investigations pertaining to the Mary Lee, Clark, Black Creek, Jefferson, Pratt, Corona, Carter Brookwood, Blue Creek, Thompson, and Woodstock beds have been published. 4/ This report, the fourteenth of the series, deals with run-of-mine coal from the Henry Ellen bed at the Acmar No. 5 mine of the Alabama Fuel & Iron Co.The Acmar mine is 1/2 mile west of Acmar, Saint Clair County, in the northern part of the Cahaba field. Present production at the mine is about 800 tons per day, all of which, accept the lump coal, is treated in jigs. The washability data were obtained by means of screen-sizing and float-and-sink tests. There are included, also, tests showing the extent of liberation of impurities by recrushing the coarser sizes of coal from the top bench and tests showing the flakiness in selected sizes.SAMPLING AT THE MINEThe Henry Ellen bed at Acmar consists of two benches separated by a shale parting. At the point of sampling the top bench was 6 feet 3 inches thick and contained a 1-inch and a 1 1/2-inch band of bone. The bottom bench was 5 feet thick and was separated from the top bench by 20 inches of shale. In taking the samples for the washability study the working face was squared up, and a representative 2-ton section was out from each bench. The shale parting was discarded, according to usual mining practice."

Nov 1, 1936

By Thomas C. Denton

The fluorite, deposit discussed herein occurs on a property known as the Snowball and comprises five contiguous mining claims in Maricopa County, Ariz. Attention of the Bureau was first directed to this property early in 1944 through .a request by D. B. Powell, original locator; to investigate his property as a possible source of fluorite and one that might 'Warrant exploration by the Bureau. The property was examined by two Bureau engineers, Thomas C. Denton and Geo. W. Huseman. It was decided to investigate the occurrence further by trenching, sampling, and diamond drilling. Work began on May 15, 194. Preparatory work, trenching and surface sampling, was supervised by Geo. W. Huseman. Drilling was in charge of R. M. Grantham. The project was completed August 8, 1944.

Jan 1, 1949