Search Documents

By F. E. Block, Stephen D. Hill

The necessity for measuring radiation dose is encountered in studying both the beneficial and damaging effects of ionizing radiation on materials . It is also necessary to know the radiation dose absorbed by the reactants in order to evaluate the efficiency of reactions or processes that are promoted by radiation . Thus , a significant effort was made at the Albany cobalt 60 facility to investigate techniques by which the exposure radiation dose can be determined . Methods including ferrous sulfate , ceric sulfate , and methyl methacrylate chemical dosimeters , ion chamber dosimetry , and an absolute radiation calorimeter were investigated . Isodose curves were constructed for several standard source configurations using the dosimetry techniques which were investigated .

Jan 1, 1964

By W. L. Staker

The Bureau of Mines investigated the use of shredded automobile scrap for copper cementation. Air agitation was used to improve the cementation rate and prevent excessive buildup of copper on the iron. The pieces of scrap were too large to be properly evaluated in the laboratory; therefore, a pilot scale test unit was constructed and the process tested at field locations. Pregnant solution was obtained from industrial leaching operations, processed in the test unit and the barren solution and cement copper were returned to the plant process stream. The test results showed that the air-agitated launder containing auto-mobile scrap was an effective means for recovering copper from leach solutions. A continuous l4-day test run was made without a noticeable decrease in cementation efficiency. The most suitable scrap product was obtained from incinerated automobile hulks shredded in a hammer type of shredder. However, it was necessary to remove small pieces such as nuts and bolts because they interfered with the discharge of the copper product.

Jan 1, 1976

By J. W. Griflith, P. A. Mack, C. M. Lang, S. Riling

"N-acetyl-beta(B)-D-glucosaminidase is a N-acetyl-beta((B)-D-glucosaminidase enzyme se¬creted by alveolar macrophages in response to phagocytosis of particulate material. Alveolar macrophages participate in the degradation and fibrosis of pulmonary tissue that results in pneumoconiosis. Known quantities of four characterized respirable dusts were bronchoscopically placed into the right caudal lung lobe of macaque monkeys. Bronchoalveolar lavage (BAL) samples were collected from dust-exposed right lung and unexposed left lung of the same individuals at 2-week intervals for 12 weeks after dust instillation. The samples were tested for N-acetyl-B-D-glucosaminidase activity to determine if the enzyme levels could serve as an indicator of pulmonary injury induced by generic coal dusts when compared to known fibrogenic and nuisance dusts. Installation of generic quartz, anthracite, or TiO2 dusts produced significant elevations of enzyme activity and increased numbers of macrophages in the dust-exposed lobes. Elevations in enzymatic activity and macrophage numbers were greatest in response to generic quartz dust. These results suggest that quantitative levels of N-acetyl-B-D-glucosaminidase activity may be a useful indicator of acute and chronic lung injury following exposure to fibrogenic and nonfibrogenic dusts.IntroductionCoal workers pneumoconiosis (CWP) is an occupational pulmonary disease associated with the inhalation of coal mine dust. An important external factor in the development of CWP is the composition of the respirable coal mine dust. A cause-and-effect relationship exists between coal mine dust and CWP, but it has not been shown that exposure to generic coal dusts will cause CWP [12]. Numerous immunological, biochemical, and cellular changes occur in CWP; however, in this study, only N-acetyl-beta(B)-D-glucosaminidase (NAGase), protein, and alveolar macrophages (AM) will be examined [7, 32, 33]."

Dec 1, 1996

By H. H. Schrenk

There is a need for a method of determining benzene vapor in air which is simple and accurate and suitable for making industrial hygiene surveys. The most widely used method in this country is the Smyth modification of the Elliott and Dalton procedure. This depends on the nitration of the benzene to m-dinitrobenzene, reduction to phenylenediamine with an excess of standard titanous chloride solution, and back titration with a standard ferric ammonium sulphate solution. This method has the disadvantages of being somewhat time-consuming and cumbersome; it requires considerable apparatus, and a special modification is necessary in the presence of toluene. Recently Cook and Ficklen have published a method based on the oxidation of benzene with hydrogen peroxide in the presence of iron salts. This method requires the use of solid carbon dioxide to freeze out the benzene. The reaction Which produces the color is complex; and only approximate quantitative estimations can be made, except in a very narrow range.

Jan 1, 1935

By C. P. Fang, V. A. Marple, K. L. Rubow, P. H. McMurry

"It has been known for some time that sizes of aqueous particles may be affected by flow-induced relative humidity (RH) changes. The RH of air flowing through an impactor decreases as a result of pressure drop through the impactor and increases because of aerodynamic cooling within the high-speed jets, as illustrated in Figure 1. Because the sizes of aqueous particles depend on RH, the impaction stage on which such particles are collected may be different from the stage where they ought to be col¬lected, based on the particle size at the sampler inlet.Fuchs (1980) reviewed literature on water vapor condensation in impactors. The reviewed impactors operated at jet velocities of 100-250 m/s. Particle size increases ow¬ing to water vapor condensation were found in all cases. In one case (Khorguani et al., 1970), it was found that very small droplets (Dp <_ 0.02 um) containing sodium chloride and silver iodide were collected in an impactor with a cut point of 0.32 µm and a jet velocity of 100 m/s. Fuchs believed that such particles could not be captured in an impactor without having been enlarged by condensation. Winkler (1974) sampled at¬mospheric dust with a rectangular nozzle impactor that had a nozzle cross section of 0.3 x 15 mm, a cut size of 0.4 um, and an average jet velocity of 100 m/s. No adhesive was used on the impaction plate. The collection efficiency increased as air humidity was increased from 20% to 100%. The effect was especially noticeable in the increased collection efficiency for hygroscopic particles, and was attributed to condensation.Extensive theoretical and experimental research work on the distortion of the particle size distributions in impactors was done by Biswas and coworkers (1985, 1987). The impactors employed in the study were a low-pressure impactor with high jet velocity stages (Hering et al., 1978, 1979) and a conventional six-stage impactor, Sierra's model 226, operated in the incompressible regime. Ammonium sulfate aerosols were chosen for the study. In the low-pressure impactor, an orifice operating at a Mach number of 1 causes a sudden pressure drop, significantly reducing the RH in the next two stages (stages 5 and 6). This results in a 0.15-um diameter ammonium sulfate droplet shrinking to about 0.07 um at stage 5 when the inlet RH is 95%. In stage 7, the tempera¬ture drop is considerable because the jet speed is sonic. For an inlet RH of 95%, a 0.03 um droplet grows to about 0.06 um. However, the same size droplet at an inlet RH of 25% grows to only 0.04 um. For the Sierra model 226 cascade impactor that is operated with a Mach number of 0.27 at the last stage (stage VI), it was found that for an inlet RH of about 67%, particle growth would occur in stage VI. At 80% RH, both stages V and VI were affected. Biswas et al. (1987) stated that Mach number alone does not determine the size biasing; the type of aerosol, the inlet conditions, the temperature and pressure ratio, and the impactor geometry (throat length, jet-to-plate distance, etc.) must be considered for each stage in evaluating the distortion of the particle size distribution."

Mar 1, 1992

By R. C. Bates

Uranium mine workers? daily exposure to radon daughters was estimated by two methods of sampling, detailed and spot-check. Both methods involve time- weighting measured exposure levels to arrive at an average exposure figure. Random sampling, or sampling without regard for the duration of exposure, has proved inadequate for estimating average exposure levels. During the first phase of the study, the breathing zones of eight workmen in three underground uranium mines were sampled for an entire shift; 20 to 36 radon-daughter samples were collected per man-shift, Analysis of these data indicated that a suitably accurate estimate of the full-shift exposure could be made by time weighting a considerable lesser number of representative radon-daughter samples. This analysis led to the spot-check method of estimating full-shift exposures to radon daughters. Additional detailed studies were made in seven mines to Learn more about the full-shift radon-daughter exposures and to test the spot-check method, In all, 617 radon-daughter samples were taken in 10 underground uranium mines during 26 man-shifts, and the spot-check method was tested 35 times.

Jan 1, 1962

By Glen C. Ware

The Bureau of Mines determined the factors involved in the corrosion of starting sheets used in the production of electrolytic zinc with the ultimate purpose of adapting zinc starting sheets to commercial practice . Under present practice , zinc is electrodeposited on aluminum cathodes and subsequently stripped for melting . The use of zinc instead of aluminum would eliminate the need to strip the deposit , thereby reducing the cost of handling and melting it , but zinc has not been suitable because it was too vulnerable to the corrosive attack of the electrolyte . Serious attack was found to be limited to the areas of the cathodes situated immediately above the surface of the electrolyte and to re - entrant corners . It was possible to avoid solution - level corrosion by immersing the starting sheets completely , exposing only a relatively heavy suspension member to solution - level attack . Zinc starting sheets could be made as reliable as aluminum and could be continued in residence for periods up to 39 days . Periods as long as a week were feasible under conditions similar to those found in commercial practice . A test of zirconium as a starting - sheet material showed that it promoted corrosion of the deposit to a lesser extent than aluminum and that the deposit adhered less tenaciously . These two properties lend themselves to the development of ways to strip deposits mechanically from zirconium starting sheets . Titanium was unsuitable for use as a starting - sheet material .

Jan 1, 1963

By J. R. Cobble

Dissolution of chalcopyrite with acidified ferric sulfate produces a sulfur layer on the unreacted chalcopyrite surface that interferes with further dissolution. The U.S. Bureau of Mines has developed a process to improve the leaching kinetics of these types of diffusion-controlled systems. The system features the Bureau-developed turbomill, an attrition grinder that scrubs the reaction product coating away from the unreacted mineral grains during leaching. The system can be operated continuously at any temperature up to the boiling point of the leaching agent. This method is a hydrometallurgical alternative to chalcopyrite smelter technology and eliminates sulfur dioxide emission problems with its associated costs. Batch testing at 900 C with the chalcopyrite-ferric sulfate system resulted in copper extraction exceeding 99 pct. At an optimal energy consumption of 1,520 kW· hjst, 95 pct of the copper was extracted. The pregnant liquor was clarified and tested for typical solvent-extraction recovery of the copper. Two-stage extraction and two-stage stripping recovered 96 pct of the copper in an electrolyte suitable for copper electrowinning.

Jan 1, 1993

By P. L. Sibrell

The U.S. Bureau of Mines has tested cyanide leaching for recovery of palladium (Pd) from spent petroleum processing catalysts. Three different catalyst samples were supplied by a spent-catalyst processor. These catalysts consisted of a zeolite base and contained 0.4 to 0.7 pct Pd. During alkaline cyanide leaching, the catalysts exhibited ion-exchange properties due to their zeolite matrices. Hydrogen ions were released from the zeolite in exchange for sodium ions in solution, resulting in a significant decrease in solution pH. This could present a safety hazard because of the potential for release of toxic hydrogen cyanide gas. A pretreatment step where the catalysts were contacted with a 1.0M sodium hydroxide solution was found to prevent the pH shift from occurring. Following the sodium hydroxide pretreatment, two stages of leaching at 160 °C with solution containing 1 pct sodium cyanide and 0.1[M] sodium hydroxide gave at least 75 and up to 95 pct Pd recovery. The Pd was quantitatively recovered from the leach solution by thermal decomposition in an autoclave at 250°C for 1 h. The Pd content of the precipitate was over 50 pct. Thermal decomposition also decreased the total cyanide content of the barren solution to less than 0.2 mg/L. The catalyst leach residues passed the Federal Toxicity Characteristic Leaching Procedure and the California Waste Extraction Test, indicating that landfill disposal of the leach residues would be acceptable.

Jan 1, 2010

By G. R. Palmer

Preliminary studies by the Bureau of Mines were conducted to determine the feasibility of a multiple-compartment, ion-exchange (MCIX) column simulator for examining the effect of multiple-orifice plates in the column. A rectangular, five-orifice, three-compartment, MCIX simulator with a cross-sectional plate area of 0.66 ft2 was used for the investigation. Orifices with open areas of 1, 3, and 5 percent were used with various operating conditions. The study was separated into three separate sections: (1) solution flow effect, (2) fluidization effect, and (3) resin transfer effect. The solution flow and fluidization studies showed that for solution flow rates of about 3 gpm/ft2, a I-percent open area plate functioned best, while at solution flow rates of 9 and 15 gpm/ft2, the best open areas were 3 and 5 percent, respectively.

Jan 1, 1981

Unfortunate occurrences resulting in injuries, loss of life, and destruction of property by explosion, fire, and other mishaps during shaft sinking focused the attention of the Bureau of Mines on the need for safety standards For such operations. Information Circular 7810 was published to meet that need. The current revision updates and replaces IC 7810. Several States have some rules and regulations applicable to local conditions, and several Bureau publications (including some now out of print) cover the hazards that may be encountered in shaft sinking. Certain requirements of the Federal Mine Safety Code and Federal Coal Mine Safety Act may be applied, but there are no definite, uniform standards that will guide those desiring to sink a shaft safely and bring about uniform safety inspections.

Jan 1, 1968

By Thomas L. Ochs

The Bureau of Mines is investigating the fundamental behavior of electric arcs in electric furnace operations. The electric arc is a poorly understood phenomenon. If the arc in a steelmaking furnace can be more carefully controlled, it should be possible to increase heat transfer to the melt, reducing both electrical and acoustical noise. As a first step toward a better understanding of the are, voltage and current signals from operating furnaces were analyzed. The results of the initial analysis show that instrumentation used in monitoring and controlling furnaces, such as meters and strip-chart recorders, gives incomplete or erroneous information to the operator and therefore leads to less than optimal control. Advanced instrumentation and analysis techniques, such as the waveform analysis used in these investigations, can improve the understanding of operation and the control of electric furnaces. This report describes the instrumentation and the numerical analysis methods used and compares these methods with standard metering and recording techniques.

Jan 1, 1986

By John E. Conley

The great demand for metallic aluminum for the prosecution of World War II caused the consumption of bauxite, the common ore of aluminum, to increase greatly. Prior to the war, the domestic deposits &apos;of bauxite, which occur chiefly in Arkansas and less extensively in Georgia, Alabama, and Mississippi, supplied only: about 30 ,percent of the ore required for aluminum-metal production and approximately 40 percent of alumina for all purposes. Enemy activities during the war seriously interfered with shipment of bauxite from the normal peacetime source in Surinam, Netherlands Guiana, South America, and focused attention on the necessity for increasing production from known domestic deposits. Even in peacetime, the production of aluminum ore in the United States could not satisfy requirements. Field drilling and exploration by Bureau of Mines engineers resulted in the discovery of important tonnages of high-grade bauxite suitable for treatment by the conventional Bayer process, Although an ore containing approximately 55 percent Al2O3 and only 2 to 4 percent SiO2 is preferable, it was necessary to use ores containing up to 8 or 10 percent SiO2. Because of the lower recoveries of aluminum with increased silica content, the Reconstruction Finance Corporation, through the Metals Reserve Company, established a base price of $4 for a 50-percent Al2O3 ore, containing 13-percent silica, with a premium or penalty of 14 cents for each percent of Al2O3 over or under 50; each percent of SiO2 under 13 was awarded a 20-cent premium, and each percent over 13 suffered a penalty of 43 cents; all prices were on the basis of 1 long ton of ore, dry basis.

Jan 1, 1949

By R. H. Harrison, D. R. Douslin

The thermodynamic properties H - H° , (H - H° ) /T , S - Sideal , S - S° Fide al F - F° , (F F° ) /T , and activity coefficient Y for perfluorocyclobutane were calculated as functions of temperatures ( 115.22 ° to 350 ° C) and molal density (0.75 to 6.5 moles / liter ) . Improved analytical and graphical correlating techniques are described .

Jan 1, 1964

By G. E. McElroy

Changes in existing airway and fan-installation conditions offer the most common opportunities for effecting economical operation of mine ventilating systems, but the largest possibilities for securing this result lie in the original design of the main airways for efficient service. Formulas, and. charts for their graphical solution, are presented herewith for the determination of the elements of airways design when the conditions of service are known, or may be roughly approximated. Although the analyses are made with particular reference to metal-mine airways, there is no essential difference between metal and coal mine main airways, and the methods presented are equally applicable to both. Little attention is paid to designing airways for maximum economy in the ventilation of metal mines. Most of the openings used as main airways are originally designed and used for transportation and other operating purposes. Even where openings are made primarily for ventilation, the possibility of their future use for other operating purposes, or even custom alone, usually results in the selection of a size and shape similar to those of existing openings. Natural conditions, such as heavy ground, often seriously limit the size of opening that can be maintained without excessive expense; and various operating factors, such as velocity limitations on traveling roads, often dictate size requirements in excess of those required for economy in ventilation only. In metal mines the main airways are, as a rule, too small rather than too large for economic service, with the general result that the quantities in circulation are often less than the mine&apos;s proper requirements over long periods, even though excessive amounts of power are applied in an effort to remedy conditions.

Jan 1, 1932

By Otto Ruhl

As the result of a study of an area comprising some 100 square miles in the Missouri-Kansas Zinc district known to have produced zinc Ore from horizons below the Grand Falls formation, it was concluded that these horizons could become an important future source of zinc. To test this conclusion and to ascertain the general conditions associated with these lower-horizon ore deposits, the Bureau of Mines undertook detailed drilling of localities thought to be favorable for deposition of ore in the Reeds Spring and. Fern Glen formations. Two sites in the Galena, Kans., mining camp were chosen for this purpose. Ninety churn-drill holes totaling 19,338 feet of bore were completed by the Bureau in two campaigns that extended from October 1944 to June 1946. Approximately 25 percent of the holes encountered ore and indicated three separate ore bodies containing substantial tonnages. Observations made during the course of the work revealed that certain structural conditions are common to ore deposits in the Reeds Spring and. Fern Glen formations.

Jan 1, 1949

By John H. Soulé

"INTRODUCTION The Mining Branch of the Bureau of Mines has used the wagon drill to sample mineral deposits in New Mexico. This method of sampling was successful and con¬stituted an important phase of the work on five exploratory projects undertaken in 1943, 1944, and 1945. The deposits varied in topographic features, geology, mineral content, and in the physical characteristics of the rocks drilled. The altitudes ranged from 630 to 7,800 feet. Three hundred and seventeen holes totaling 6,852 feet were drilled. The deepest hole was 66 feet; the average depth was a little less than 22 feet.The results of the above-mentioned work form the basis of this report. Special attention is given to the later and more improved techniques used. This report was written with the expectation that the procedures might prove advantageous to others in the exploration and sampling of near-surface mineral de¬posits, and that a more extended use of the technique might result.AcknowledgmentsAcknowledgment is due Charles H. Johnson, chief of the Rolla Division, Mining Branch, for helpful suggestions in starting this work, and to J. H. Hedges, chief of the Tucson Division, Mining Branch, W. R. Storms, engineer-in-charge of the Silver City, N. Mex., Field Office, and Donald H. Mullen, mining engineer attached to that office, for assistance in preparing and editing this report."

May 1, 1947

By A. W. Ambrose

A few years ago, (March 3, 1915) Congress passed a law providing for the establishments of ten mining experiment stations under the supervision of the Bureau of Mines. In 1917 the Secretary of the Interior decided that one of these stations should be devoted to Petroleum, and in the early part of 1918, approved the establishment of the Petroleum Experiment Station at Bartlesville, Oklahoma, upon the condition that the city furnish the site for the buildings and guarantee $50,000. for the erection of the buildings. A building site of 5 acres and the necessary building fund was furnished by the Bartlesville Chamber of Commerce.The buildings consist of an administration and laboratory building, both of brick construction. The former is a two-story structure of eight rooms. A large room occupying over half of the main floor is devoted to the library, reception room, and clerical force. The remaining rooms comprise a drafting room and six offices occupied by the staff assigned to this station. The laboratory is a one-story brick building and contains a well-equipped chemical and physical laboratory, also a machine shop and mechanical laboratory. In addition to the main buildings there now are on the property an experimental refinery, a blue-print house, and a store house. These latter buildings are all of sheet-iron construction.

Oct 1, 1920

By L. B. Pankratzt

The heat capacity of dimo1ybdenum carbide (Mo2C) was measured from 51° to 298° K, and the entropy at 298.15° K was evaluated. Heat content measurements above 298.15° It were conducted for dimolybdenum carbide (M0caY) and monotantalum carbide (TaC). The results were combined with known heats of formation and the 298.15° K entropy for TaC to obtain values of the heat and free energy of formation from 298.15° K to 1,400° K for MoaC and from 298.15°K to 1,800° K for TaC.

Jan 1, 1966

By F. A. Skirvin

Purification techniques were investigated for removing low-level metallic impurities from tungsten hexachloride. These techniques included distillation) fused-salt scrubbing) zone refining) and adsorption. Fractional distillation of tungsten hexachloride was found to be an effective purification method. The impurity levels of molybdenum) iron) nickel) copper) magnesium) and manganese were reduced to provide a tungsten halide sample which contained a total of less than 10 ppm detectable metallic impurities. Purification by fused-salt scrubbing of tungsten hexachloride in a lithium chloride-potassium chloride eutectic produced a hexachloride product which was of approximately the same quality as that obtained by distillation. Zone refining and adsorption did not appear to be as effective as distillation or fused-salt scrubbing.

Jan 1, 1967