Search Documents

By Richard W. Lewis, Lloyd Carpenter

The objective of the investigation was to determine spectrochemically 19 elements in the general range of 0.5 to 1,000 ppm in high - purity hafnium and its compounds . Samples were converted thermally to hafnium dioxide , mixed with buffer - carrier - internal standards , and excited by a dc arc . Spectra were recorded on photographic plates . Transmittance values were recorded densitometrically and converted to relative - intensity ratios . Four groups of standards were used to establish analytical curves from which the concentrations of impurities were obtained . Average precision of the method was 14.2 percent relative standard deviation , and relative error was 4.2 percent .

Jan 1, 1964

By T. T. Campbell

This report traces the development of techniques for the preparation of high-purity rare-earth metals. Rare-earth metals, excepting samarium, europium, and ytterbium, were prepared by converting their oxides to anhydrous chlorides or fluorides and reducing the rare-earth halides with active metals such as lithium or calcium. High-purity, anhydrous rare-earth chlorides were prepared by dissolving the rare-earth oxides in hydrochloric acid to form hydrated chlorides and by subsequently dehydrating the hydrated salts in the presence of ammonium chloride at temperatures ranging from 70° to 360° C. while under reduced pressure (50 microns to 1 inch Hg). The chlorides were also prepared by direct chlorination of rare-earth oxide-carbon mixtures. Reaction efficiencies in excess of 95 percent were obtained by either method; however, purer chlorides were prepared by the aqueous ammonium chloride conversion method. Purification of yttrium chloride by high-temperature vacuum distillation proved to be an effective method of separating, oxygen-bearing compounds from the chloride. Yttrium metal prepared from purified chloride contained significantly smaller amounts of oxygen (990 p.p.m. oxygen in yttrium metal prepared from raw chloride and 200 p.p.m. in that prepared from distilled chloride).

Jan 1, 1961

By Roy F. Abernethy

This publication by the Federal Bureau of Mines contains the free-swelling indexes for 2,812 samples of coal received from January 26, 1948, to July 15, 1957, and the Hardgrove grindability indexes for 2,339 samples of coal received from June 23, 1947, to July 15, 1957. These data consist of the origin of the sample, bed name, and analysis. Summaries show the high, low, and average values for each bed. The free-swelling index is a relative measure of the caking properties of a coal when burned on a grate, and the Hardgrove grindability index is used to estimate the relative ease of grinding coals. Development and standardization of these test procedures were at a much later date than those for the more familiar tests, such as proximate and ultimate analyses and calorific value determinations. The newer tests are valuable in supplying supplemental information, particularly for assisting in evaluating coals used in certain types of combustion processes.4/ Data from such tests are important to designers of burning equipment, operating engineers, and purchasing agents. Data from these newer tests are scarce and scattered through a number of publications. Special projects were started to determine the free-swelling and grindability indexes, in addition to the regular analyses on the tipple samples collected by Bureau engineers. Since the start of these special projects, all the coal fields of commercial importance have been adequately covered in the sampling program.

Jan 1, 1961

By J. B. Gayle

The Bureau of Mines studied the effects of air oxidation on the recovery of float coal. Both batch-and continuous-type tests were made on six bituminous coals, representing the range in rank of coals now commercially used for carbonization, and on one anthracite coal. The effects on flotation recovery of oxidation at 1000 C for periods up to 50 days were investigated using an alcohol-type frother and a kerosine-pine oil reagent. Two series of release analysis tests were made, using one medium-volatile bituminous coal. Float coal recovery was adversely affected by oxidation in all tests where the alcohol-type frother was used. Conversely, a small degree of oxidation improved recovery with kerosine-pine oil frother for some of the coals in continuous tests. Prolonged oxidation (beyond about 14 days) adversely affected float coal recovery for all coals, the effect being more pronounced for batch-type tests and for tests using alcohol-type frother. Reagent selectivity for the rejection of both ash forming and sulfur bearing minerals was reduced by oxidation. Severe reduction of reagent selectivity required only about 3 days' oxidation for alcohol-type frother but more than 10 days' oxidation when the kerosene-pine oil reagent was used.

Jan 1, 1965

By R. H. Lien

The Bureau of Mines developed a flue gas desulfurization process as part of its goal of minimizing the undesirable environmental impacts associated with energy and mineral-processing plants. The modified citrate process involves absorption of sulfur dioxide (S02) in a buffered citric acid solution. The S02-loaded solution is regenerated by countercurrent contact with steam in a packed tower. The wet S02 product is then dried and can be liquefied or further processed to make sulfuric acid. Test data from process investigation unit studies are presented. Material balances, flowsheets, and cost estimates are given for recovering S02 from copper smelter reverberatory gas, lead smelter sintering machine tail gas, and power-plant stack gas. Operating cost estimates show the process will add $0.04 per pound of copper, $0.01 per pound of lead, and $0.015 per kwhr to the cost of the respective operations. These costs could be substantially reduced if a source of waste heat was avail-able to provide the process steam requirements.

Jan 1, 1982

By C. J. Walker, Ray V. Huff

The feasibility of inert - gas cushions in underground gas storages was studied by the Bureau of Mines in accordance with a continuing program of cooperative research between the natural gas industry -- through the American Gas Association . As mixing of the inert - gas cushion with the stored natural gas is undesirable , the various mechanisms tending to bring about such mixing were the subjects of both theoretical and experimental studies . These studies indicated the practicability of such cushions is dependent upon both reservoir and operating conditions . Equations and tables of illustrative data relating the various reservoir and operating conditions to the expected time required for undesired mixing to occur in ideal reservoirs are presented . This information permits estimating the relationship of such factors in actual storage operations .

Jan 1, 1964

By P. E. King

The U.S. Bureau of Mines is conducting an ongoing research project to better understand the phenomena involved within electric arcs utilized in electric furnace steelmaking. With a better understanding of the physical and electrical characteristics involved, dynamic or predictive control of electric arc furnaces may be possible. A mathematical model is presented, but not solved, and the system of coupled equations is analyzed. Characteristic parameters are used to determine relative importance. In this manner, significant quantities are dermed. The parameters found to contribute little to the system of equations of motion are ignored. A resultant simplified system is identified, and directions for further study are indicated toward control of electric arc furnaces.

Jan 1, 1990

By John W. Cole

The Butte district has been the principal producer of metallurgical-grade manganese in the United States since World War I. Manganese dioxide nodules are produced from rhodochrosite ore by concentrating the rhodochrosite and roasting the concentrate in rotary "cement-type" kilns. The Anaconda Copper Mining Co. is the only producer at present. Under the stimulus of a purchasing program administered by Metals Reserve Company during World War II, however, several independently owned or operated mines (including the Norwich) produced manganese carbonate ore. These mines were examined in Juno 1949 by John W. Taber, mining engineer, Bureau of Mines. A core-drilling program to develop ore in the Norwich mine was recommended and approved. drilling was completed early in 1950. This report gives factual data obtained.

Jan 1, 1951

By Edwin B. Cook

This report presents the results of calculations of the equilibrium composition of the products of combustion with air of six different mixtures of octane CgH18, plus PbEt4 and halogen-bearing scavengers at three air-fuel ratios, at pressures of 5 and 30 atm., and at temperatures of 350°, 1,000°, 1,800°, and 2,000° K. The air-fuel weight ratio has the values 12, 15:12, and 18. The concentration of PbEt4, M, in milliliters per gallon of iso-octane, has the value 1 or 3. The word "case" is used to designate the halogen concentration. Three cases have been considered [ ]

Jan 1, 1953

By C. A. Allen

"The problem of signaling to the hoisting engineer from a moving cage in the shaft has been considered by many mine operators for a number of years. There are several methods in use in different mining districts, and so far as the writer is aware they have been further developed in Utah than in any other state. The latest installations are of interest because they use a very low-voltage circuit for the shaft wires and also because the wiring can be so arranged that the hoist can be stopped from the cage, if so desired.The first installation in Utah was in the shaft of the Centennial-Eureka mine under the management of C. E. Allen. It was placed in operation in the summer of 1899, end has been in continuous and satisfactory operation for 21 years. The arrangement consists or two bare wires down the shaft carrying a current at 60 volts potential, with a device on the cage for making connection between the two wires. This device is simply a short piece of wire which is thoroughly insulated from the cage and is operated by a short lever. Whenever the cage rider wishes to signal the engineer he pulls down the lever, forcing the short wire out against the two bare wires, thus making a circuit which rings the bell in the hoist-room. A similar device was planned in the Grand Central shaft at Mammoth, Utah, but was later abandoned. The cause of failure was reported to be that the shaft was very wet."

Jun 1, 1920

By Clayton M. Rumsey

The U.S. Bureau of Mines investigated prospects and mineralized areas in and adjacent to the Indian Pass and Picacho Peak study areas in 1983 and 1984. The Indian Pass study area contains 33,640 acres and the Picacho Peak study area contains 5,450 acres. The study areas are located in the southeast corner of California and are underlain by Precambrian gneiss, Pre-Tertiary metavolcanic and metasedimentary rocks, and Tertiary volcanic and non-marine clastic rocks. Low-grade gold-silver resources may be present in hydrothermally altered gneiss in the upper plate and altered schist in the lower plate of the Chocolate Mountain thrust fault. The thrust fault is exposed in the study areas for about 3.5 miles west and 5 miles east of Indian Pass. Mineralized zones in the thrust plates were not discovered until 1983. Earlier prospecting explored areas containing minor copper carbonate occurrences in schist and sedimentary and volcanic rocks that are younger than the thrust. Twenty-three mines, prospects, and mineral occurrences inside the study areas and fourteen outs; de were examined for this study. These surficial copper occurrences have been prospected extensively in the study areas; large areas have been scraped, pitted, and trenched by bulldozers. However, they appear to be of limited economic significance. Slightly mineralized zones are in the northwest part of the Indian Pass study area where granite contacts sedimentary and volcanic rocks.

Jan 1, 1986

By H. L. Gibbs

A portable radon monitoring instrument capable of making on-the-spot measurements of the radon gas content of uranium mine atmospheres was designed and constructed. The monitor was tested in the laboratory and in operating uranium mines. Good correlation was obtained between the monitor readings and radon measurements made on mine atmosphere samples taken in radon bottles.

Jan 1, 1973

By John C. Holtz

"INTRODUCTION Information on the gaseous products from the detonation of explosives has been obtained in two ways. In the first, the atmosphere in mines is analyzed after blasting, and in the second, the gases found after detonating an explosive in a testing apparatus are analyzed. The Bureau of Mines, in a cooperative research 3/ that compared data obtained in the field with those obtained in the testing station, showed that the results were not in entire agreement. The production of carbon monoxide was found to be governed chiefly by the oxygen balance of the explosive, but the production of oxides of nitrogen did not change in so simple a manner. Because of the increasing interest in correlations between the composition of the explosive and the production of toxic gases, it seemed desirable to continue the investigation.PURPOSE OF INVESTIGATIONAs field tests are both time consuming and expensive and as field results are affected by factors that are not always under control of or clearly evaluated by the operator, the purpose of this investigation is to develop a testing-station procedure that will reproduce the gaseous products quantitatively under known conditions analogous to those that may be expected in the field. In addition, the factors affecting the formation of toxic gases, particularly oxides of nitrogen, will be studied,"

Apr 1, 1940

By D. S. Burgess

An investigation of the hazard of spillage of liquefied natural gas (LNG) onto water is described. About 2,000 gallons of LNG were consumed in various tests. The initial vaporization rate of LNG following spillage was found to be 0.037 lb/ft2 sec; when the spill was confined, this vaporization rate was moderated after about 20 seconds by the growth of an ice layer on the water surface; when the spill was unconfined, a coherent ice floe was not observed and the vaporization rate was essentially time independent. The maximum diameter (in feet) of the spreading LNG pool was found to be given by 6.25 Wo 1/3, where Wo is the weight of LNG in pounds, Downwind of a natural gas source, time-averaged methane concentrations were given in good approximation by standard air pollution equations. However, peak concentrations were as much as twentyfold higher than average, adding an additional factor to the assessment of hazard. The effect of layering by the cold vaporized natural gas was similar to the effect of a temperature inversion on normal gases in the atmosphere. Small-scale explosions were observed on pouring LNG onto a water surface; no single explanation seems pertinent to all of the incidents observed.

Jan 1, 1970

By F. S. Crawford

Safety devices and guards are often looked upon as the last word in safety by the men around the shop or large industrial plant . However , thorough knowledge of the details of their jobs and of the dangers attending them are even more important . It should be unnecessary for all men to go through the experience of the first man to meet an unknown danger , but that appears to be about the only way by which many learn . Practically every danger connected with the job around a mine , blast furnace , steel mill , foundry , coke oven , cement mill , or other operation , was encountered for the first time by someone , and if he was fairly fortunate he either got hurt or just missed being injured and lived to tell his " budaies " how it happened; he spread the knowledge of that particular danger . Sometimes , but not often , a man can foresee a danger . If he could always be on guard and remember everything he had ever learned and also know everything that had happened to the other fellow , and then let that knowledge keep him aware of the dangers in his own immediate " job , " so that he would work the safe way for both himself and the other fellow , he would have what safety engineers call " safety consciousness . " Being safety conscious is a fine attribute , as it really means knowing all about one's job . A man who is really safety conscious is one of the best and most efficient workmen in the whole plant . The boss wants men of that kindmen who want to learn and who try to learn every little detail about their jobwhere there is danger of spoiling the heat or getting burned by hot metal in a steel plant or of loading rock instead of coal or ore in a mine . Such men know how to do whatever job they are on easily and with the least amount of hard work and at the same time get it done as quickly as possible with safety . A man who is safety conscious has to nearly all intents and purposes developed eyes in the back of his head , if he is in a big mill where there if something going on all around him . These eyes are not real eyes , but they are what might be termed a sixth sense which he has developed by his experience in the mill as well as in other dangerous work which he may have done before in other plants . There may be occasions when a man's safety consciousness will leave him for just a short time ; this is likely to happen when he is thinking about a quarrel he had with his wife which has not been cleared up happily , or perhaps when he has bought too many things on installment and with sickness at home

Apr 1, 1931

By James A. Powell

A seismic system which utilizes in-mine geophones to detect trapped miners has been developed. Tests at the Bureau of Mines Safety Research Mine at Bruceton, Pa., and at two operating mines indicate such a system has a maximum detection range in excess of 1,000 feet. The system is fieldworthy and portable and requires less than 30 minutes to set up and check. Real-time detection is possible.

Jan 1, 1976

By R. L. Grayson, L. L. Probert

"A three-year project focusing on the depth profiling of respirable coal mine dust particles using scanning electron microscopy coupled with energy dispersive X-ray analysis resulted in the development of statistically classified particle-behavior models. The models depict the changing silicon fraction for particles at 5-, 7-, 9-, and 11-keV accelerating voltages, thereby giving a clear indication of the nature of various types of mineral particles. This paper focuses on the results for respirable quartz particles sampled from five underground coal mines across the US. Through statistical analysis of results the relationship between the fraction of surface available quartz in respirable dust samples and coal rank is established for three Pennsylvania coal seams. IntroductionThis is the last in a series of papers detailing the results of SEM/EDX-based analyses of respirable coal mine dust particles collected from field sampling. Previous papers have detailed preliminary results and the statistical validity of the methodology (Grayson, Andre, and Simonyi, 1990; Grayson, 1991). This paper presents the final results of the analysis of respirable dusts from five coal seams with a range of coal rank:• Lykens Valley seam (anthracite), eastern Pennsylvania• Brookville (A) seam (mid-vol bituminous), central Pennsylvania• Pittsburgh seam (high-vol B bituminous), western Pennsylvania• No. 6 seam (high-vol C bituminous), Illinois• Wadge seam (sub-bituminous A), ColoradoSEM/EDX-based techniques were applied to try to clarify the role of quartz as an etiologic agent in coal workers' pneumoconiosis (CWP). It was hypothesized that previous studies were hampered by the restrictions of bulk analysis techniques and that particle-level analyses were needed to answer a number of questions concerning the role of quartz in CWP and its progression.Since 1985, a large number of the respirable dust samples submitted to MSHA are analyzed for free silica (Tomb, Parobeck, and Gero, 1986). Our reasearch shows that conventional bulk analysis techniques may not give a true indication of the biologically available, or active, quartz in mine dusts. Analytical evidence indicates that respirable dust samples may contain many quartz particles that are occluded, or coated, resulting in a bulk analysis for ""free silica"" that may not be indicative of the biologically available quartz surface."

Dec 1, 1996

By H. D. Hess

This report describes in detail a unique occurrence of fersmite, (Ca, Ce, Na) (Cb, Ti, Fe, Al)2 (0, OH, F)6, which occurs as small anhedral inclusions and intergrowths with a tantalum-free columbite found in the metamorphic complexes of Ravalli County, Mont. Chemical and crystallographic data along with the physical and optical properties agree in general with those given in the original description of fersmite from the Ural Mountains of Russia. X-ray diffraction data not given in the original description and more specific optical data have been determined. The Montana fersmite, now established as the second occurrence of this rare calcium-columbate mineral, was discovered during a routine Bureau of Mines mineralogical examination of a prospector's sample.

Jan 1, 1960

This manual is for use by mine operating personnel and vehicle manufacturers in the selection and proper use of automatic fire protection systems for underground metal and non-metal mining vehicles. Most of the currently available systems are manually operated, dry chemical fire suppression systems. When properly designed, installed, and maintained these systems have proven to be effective both in fire suppression and in withstanding the rugged mine environment. Portable fire extinguishers and manually actuated systems have provided adequate protection for most of the reported fire incidents. However, there have also been incidents where injuries and property losses would not have occurred if the vehicle had been protected with an automatic fire protection system. The need for reliable automatic systems exists when the operator is not present, especially when the vehicle engine is running without the operator in the cab; and also in cases where the operator leaves the vehicle to fight a small fire with a portable and is then forced to abandon the vehicle because the small fire becomes uncontrollable. In the later cases manual systems on the vehicle are never actuated. Although these incidents have been relatively few in number in the past, the increasing use of mobile diesel powered equipment and the related importance of personnel safety, high costs of the mining vehicles, and high cost of down time warrant consideration of automatic fire protection systems. The fire history data and the design concept discussed in this manual were developed under the Bureau of Mines Contract H0252038 which is part of the government's mining research safety program. The purpose of the contract was to develop a low cost, reliable, prototype automatic fire control system for underground vehicles. The industry needs were determined through an extensive mine visitation program, and the prototype system was demonstrated on a vehicle in an underground mine fire test. The system developed under this contract was specifically designed for a load-haul-dump. However, the design concept is applicable to the full general class of mobile underground mining equipment.

Jan 1, 2011

By K. B. Rojiani

Surface mining activities disturb large tracts of land resulting in the potential for greatly increased downstream sediment loads. The Surface Mining Control and Reclamation Act of 1977 places increased emphasis on the protection of the environment from the adverse effects of surface mining operations. Surface mining activities must be planned to minimize disturbance to the hydrologic balance, erosion and sediment contributions to receiving streams. Sediment ponds must provide a sediment storage volume equal to the accumulated sediment volume from the drainage area as determined by the Universal Soil Loss Equation (USLE) or other empirical methods established by the regulatory authority. It has thus become extremely important for the mining industry to secure more accurate estimates of potential erosion losses and sediment yield. Accurate estimates of sediment yield are required for the planning, design and successful operation of sediment control systems such as detention ponds and other alternative control structures and for evaluating the effectiveness of land management practices. The principal soil loss prediction procedure available for use is the LISLE. The USLE procedure is inadequate for use in predicting soil loss from surface mine regions for a number of reasons. These include: 1. The USLE was developed to estimate average average annual loss from agricultural soils. It cannot predict accurately soil loss for specific storm events. In surface mine regions a major portion of the soil loss occurs during the initial six months to one year of active mining. Accurate estimates of soil loss over short periods are thus required for the design of control structures. 2. The slope length and gradient factors used in the USLE were obtained from data or cropland having slopes ranging

Jan 1, 1983