Search Documents

By J. F. Shultz

The Bureau of Mines investigated the hydrogenation of carbon monoxide and carbon dioxide over Raney nickel catalyst and nitrided fused-iron catalyst using both a single-pass and a recycle system. Activation energy over Raney nickel catalyst is 29 to 32 kcal/mole for synthesis from either CO or CO2, Pressure dependence of the gas conversion is to the 0.3 power for synthesis from CO and to the 0.5 power for synthesis from CO2. Nitrided fused-iron catalysts were tested using high recycle rates and 3H2+lCO, 2H2+lCO, and 1H2+lCO feed gas at 21.4 atmospheres absolute pressure. The relative usage of hydrogen (moles H2 consumed per moles Ha+CO consumed) was larger than in corresponding single-pass tests, and the relative usage of hydrogen approached the feed gas ratio monotonically as conversion increased. Activation energy was found to be 12 or 13 kcal/mole fresh feed gases of 3H2+lCO or 2H2+lCO. For single-pass operation the activation energy under the same conditions was 19 to 21 kcal/mole.

Jan 1, 1967

By Larman J. Heath

Preliminary results of an explosive fracturing-solvent injection heavy oil recovery experiment conducted by the Bureau of Mines at a shallow oil reservoir near Bartlett, Kans., are given. Three wells 35 to 50 feet apart were drilled to a depth of 360 feet, and an open hole interval from 300 to 350 feet in the Bartlesville Sandstone Formation was explosively fractured with 3,000 pounds of pelletized TNT in each well. Laboratory tests were made on cores obtained from these wells to confirm the suitability of using an aromatic-type solvent. Injection of a 74-percent aromatic solvent was begun into one well and continued intermittently for approximately 2 months. Crude oil production amounted to 29.6 bbl, or 11.7 percent of the total oil con¬tained within the three-well interwell zone.

Jan 1, 1972

By Janet Torma-Krajewski

Job tasks that involve exposure to work-related musculoskeletal disorder (WMSD) risk factors may impact both the risk of injury and production downtime. Common WMSD risks factors associated with mining tasks include forceful exertions, awkward postures, repetitive motion, jolting and jarring, forceful gripping, contact stress, and whole body and segmental vibration. Mining environments that expose workers to temperature/humidity extremes, windy conditions, and slippery and uneven walking surfaces also contribute to injury risk. National Institute for Occupational Safety and Health (NIOSH) researchers worked with powder crew members from the Bridger Coal Company to identify and rank routine work tasks based on perceived exposure to WMSD risk factors. This article presents the process followed to identify tasks that workers believed involved the greatest exposure to risk factors and discusses risk reduction strategies. Specifically, the proposed prill truck design changes addressed cab ingress/egress, loading blast holes, and access to the upper deck of the prill truck.

Jan 1, 2009

By T. J. Ballard

Chromite deposits in the vicinity of Louise, Troup County, Ga., were studied y the Bureau of Mines from September 1, 1942, to March, 15, 1943. They are about three-fourths of a mile southeast of Louise and 8 miles northeast of La Grange, Troup County, Ga. The existence of chromite deposits in that area has been known for more than 75 years, but no active prospecting was done until World War I. Prospecting continued intermittently' until 1928. The Bureau became interested in the deposits in connection with its strategic minerals investigations during World War II. The chromite in these deposits occurs as grains ranging from "pin-head" size to 3/8-inch and occasionally 1 inch. Some of the material is magnetic, indicating the presence of magnetite. Of the 300 samples taken during the course of the project, 266 were analyzed. Tables showing the analyses accompany this report.

Jan 1, 1948

By E. P. Youngman

Gold and precious stones were mined in Egypt in prehistoric times. This mining, carried on at intervals, extended over thousands of years, until about 1300 A. D. Then ensued a dormant period of several hundred yoars. In the mean- time Europe made great rogress in mining practice, metallurgy, and geology and sent out various expeditions during the nineteenth century to investigate ancient mines. But the exploratory work produced no material results, and not until the beginning of the present century did actual mining recommence. The reopening of old gold mines in Rhodesia aroused interest in London and Paris, and these cities provided the capital necessary for the investigation of the ancient minee in West Africa and Egypt. Speculation resulted in the division of most of the uncultivated area of Egypt and the Sudan into huge concessions, and a number of expeditions were made; but after an unprecedented activity in West Africa, roaction set in, and the flow of capital ceased. The concession- aires, mostly individuals with insufficient capital and with a misconception of the initial difficulties of communication, water supply, and labor, allowed

Jan 1, 1932

By Richard D. Hagni

The character of phosphorous-bearing minerals in the Birmingham red Iron ores and iron-bearing minerals in the Eufaula bauxite deposits in Alabama has been Intensively studied by petrographic, ore microscopic, luminescent microscopic, scanning electron microscopic, electron microprobe, and x-ray diffraction techniques. A total of 15 types of phosphorous-bearing mineral grains have been recognized in Birmingham iron ores by their characteristic sizes, shapes, and distributions. Size measurements, modal analyses, and texture analyses have permitted an estimate of potential liberation of phosphorous from the iron ores by beneficiation to be 27% In areas of previous mining and 60% in areas of current iron reserves. Fine grinding, selective flocculation, and flotation may constitute the best beneficiation technique for future research. Hematite and goethite are the most important iron minerals in Eufaula ferruginous bauxites, but pyrite, marcasite, and siderite are Important iron minerals in some varieties of ferruginous bauxite, and lepidocrocite and ilmenite occur locally in minor quantities. Although simple screening will remove the coarsest iron-bearing grains, research on the utilization of high gradient magnetic separation to reduce the amounts of iron-bearing grains is recommended.

Jan 1, 1981

By E. P. Carman

This report is the 19th in a series summarizing Bureau of Mines research and technologic work on coal and related investigations. The first 17 reports covered fiscal years; however, the 18th report3/ covered the 18 months from July 1, 1952, to December 31, 1953, to permit the publication of this and subsequent reports on a calendar-year basis. Most of the material in this report relates to publications by Bureau authors issued during the reporting period. Some work is referred to on which the results have not yet been published or may not be published for security or other reasons. In a few instances publications are mentioned that were issued before the reporting period but were not included in previous reports. Further details on the published work described herein may be found in the publications cited in the footnotes. Research and technologic work on coal by the Bureau is directed toward developing and encouraging increased conservation of coal resources through safer and more efficient mining, preparation, and utilization. Significant advances were made during the year in these fields, particularly in coal-mine safety and in preparation and utilization of the various ranks of coals.

Jan 1, 1956

By Louis C. Brichta

The rapid; depletion of' known high-grade ore deposits in the Tri -State lead-zinc district and the recognized need for the development of additional reserves led the Bureau of Mines to make preliminary examination of sites possibly adaptable to low-cost open-pit mining methods. Abandoned mines whose ore deposits were known to have occurred at shallow depths naturally presented favorable test points for the development of possible open-pit orebodies. The Lone Elm mine was in this category.

Jan 1, 1949

By Martin A. Elliott

Recommendations for safe practices in the operation of Diesel engines underground must take into consideration the hazards that might be created if the composition of the underground atmosphere differs from that of normal air. One aspect of this problem was discussed in the second report6/ of this series, which presented the results of tests in which a Diesel engine was operated with mixtures of normal air and exhaust gas supplied to the intake of the engine. Atmospheres .of this type were studied first because they will be present whenever the exhaust was is discharged into the atmosphere of underground workings in which an engine operates. Diesel engines in underground service may operate in another type of atmosphere, namely, one

Jan 1, 1941

By Martin A. Elliott

Recommendations for safe practices in the operation of Diesel engines underground must take into consideration the hazards that might be created if the composition of the underground atmosphere differs from that of normal air. One aspect of this problem was discussed in the second report6/ of this series, which presented the results of tests in which a Diesel engine was operated with mixtures of normal air and exhaust gas supplied to the intake of the engine. Atmosphere .of this type were studied first because they will be present whenever the exhaust was is discharged into the atmosphere of underground workings in which an engine operates. Diesel engines in underground service may operate in another type of atmosphere, namely, one

Jan 1, 1941

In 2007, a total of 4,639 stone mining operations reported employment to the Mine Safety and Health Administration (MSHA).1 Stone mines comprised 31.2% of all mining operations. ? Mines producing the primary commodity of limestone (crushed and broken) comprised the largest number of operations (n=2,051; 44.2%). ? Stone mining operations were located in all states and territories except Delaware and North Dakota. ? Pennsylvania had the most stone mines (n=373; 8.0%), followed by Texas (n=352; 7.6%).

Aug 1, 2009

By A. Renton Amell

The rate of dissolution of U02 was measured in acid solutions similar to those used for in situ leaching, with S04 of 10-1.82 to 10-4 M, Fe(III) of 10-2 to 10-4 M and pH's of 1.1 to 2.3. The dependence of dissolution rate on pH was small and inconsistent, probably reflecting the combined effects of a very weakly polar oxidizing complex, probably FeSO4+, and a nearly neutral U02 surface. Differences in the state of the U02 surface may explain this variability as well as contrasts between these results and results reported in other work. Changing either S04 or Fe(III) concentrations significantly affects dissolution rates. Increasing low sulfate concentrations in solutions containing 10 2 M Fe(III) at pH 2 results in formation of FeSO4+. In such solutions, rates increased with (S04)/(Fe(III)) up to 1:30, thereby indicating that the oxidation of U02 by FeSO4 is more rapid than by Fe3+. However, the dissolution rate decreased at higher (SO4)/ (Fe(III)), due either to sorption of SO42- on the UO2 surface or to formation of other less reactive sulfate complexes such as Fe(S04)2 or FeHSO4+ However, Fe(III) concentration is the dominant factor in determining solution rates. The rate was directly proportional to ferric iron concentration, indicating that the rate-determining step of the dissolution reaction is a single-electron oxidation by a ferric complex. Dissolution rates were lower in solutions of 0.1 and 1.0% H202 (0.029 and 0.29 M) than at similar concentrations of ferric iron because of formation of an insoluble surface coating of uranium peroxide, UO4?4H20. This phase may limit the value of hydrogen peroxide as an oxidant in lixiviants, not only by its very low solubility, but perhaps also by filling pores and reducing permeability in the ore body.

Jan 1, 1978

By Wm. O. Vanderburg

This report on the mining and milling of tungsten ores is the second part of a general study of the domestic tungsten industry. The first part, comprising general information on tungsten, has been printed as Bureau of Mines Information Circular 6821. The purpose of these papers is to increase efficiency in the mining, preparation, and utilization of the tungsten resources of the United States. The tungsten industry forms so small a part of the vast mining and metallurgical operations of the illation that private metallurgists have not had enough inducement to give special attention to the recovery of tungsten minerals from the ores, and many of the small companies are financially unable to undertake research work. A study of the milling of tungsten ores reveals that further improvement is possible, especially in the treatment of slimes. Recent experimental work by the Bureau shows that the flotation process is applicable to certain tungsten ores. The future of the tungsten industry it the United States depends to a great extent on utilization of the low-grade deposits of the contact-metamorphic type.

Jan 1, 1935

By M. J. Sapko

The pressure and flame development of the methane-air-nitrogen system was investigated in the Bureau's l2-foot-diameter sphere to define buoyancy effects and to develop relationships for predicting venting requirements. Pressure rise (?P) is defined as a function of time (t) and nitrogen dilution and is shown to deviate noticeably from the cubic law (?P = kt3), depending upon the period of combustion and the mixture composition. Corresponding flame speed (Sf) and burning velocity (Su) data are given which show that Sf is time dependent and that Na dilution has a greater effect than air dilution in inhibiting the flame propagation. The Su data agree with "accepted" values and are unique in that they are based on much larger flames than those used in other investigations. Downward propagation limits are shown to depend mainly upon buoyant forces, which can affect the burning of even stoichiometric CH4-air systems. Theoretical expressions, based on the mixture burning velocity and expansion ratio, are given for predicting the venting requirements for ignitions of hydrocarbon-air-nitrogen mixtures in spherical or cubical enclosures.

Jan 1, 1976

By W. M. Merritts

The control of coal dust created and released during the operation of continuous mining machines in bituminous-coal mines of the United States is a problem. The interest manifested in this problem indicates the seriousness of the hazards involved, particularly when the dust has not been abated at its source and has become air-borne. Officials of the Sunnyside No. 1 mine, Kaiser Steel Corp., were confronted with the problem of abating the coal dust created by operation of a recently installed continuous-mining machine, and they requested the aid of representatives of the Coal-Mine Inspection Branch, Bureau of Mines, United States Department of the Interior, in developing an effective method of allaying the coal dust at its source.

Jan 1, 1951

By D. S. Kingery

Recent Federal coal-mine inspections have revealed some good and some definitely hazardous practices and systems for transporting; handling, and storing lubricants in and about coal mines. Improper storage or handling of. lubricants in coal mines has caused disastrous mine fires or, by supporting combustion, has made fires from other sources more difficult to fight. Careless handling of grease and oil around electrical equipment wastes much oil and permits entrance of grit and foreign substances into the working parts, which causes excessive wear and increases the possibility, of electrical ignition.

Jan 1, 1943

By R. W. Van Dolah

An attempt has been made in this investigation to define the conditions under which ammonium nitrate (AN) might detonate as a result of involvement in fire. The initiation of detonation by shocks derived from explosives or from projectile impact was investigated as a function of temperature and charge diameter. A new technique was devised to investigate the burning of raw and contaminated AN under pressure. No transition, to detonation in AN was obtained in the burning experiments. The critical diameter for detonation of fertilizer-grade AN was found to be quite small when the AN was at temperatures just below melting point; this indicates that initiation of detonation may be less difficult at elevated temperatures but such initiation by gas-phase detonation was shown to be unlikely. Transition from burning to detonation was obtained with AN intimately mixed with fuels that included polyethyl-ene, paper, and fuel oil when these were contained in vessels with restricted vents. However, the experimental results supported by an analytical study indicate that the initiation of detonation in AN from fire exposure in normal storage and from transportation incidents is quite improbable. The detonation of AN in recent incidents more likely may have resulted from the effects of adjacent explosions.

Jan 1, 1966

By Howard E. Parkinson

In 1969, new coal mine health and safety legislation was enacted in the United States. As a result of this legislation, the Department of Interior, Bureau of Mines has carried out communications research aimed at developing whole mine communications for increased safety and efficient operation. The research has advanced and many promising results are now being demonstrated to the mining industry. However, there remains a challenge to further improve wireless communications within the mine workings, and through the overburden above the workings. The objectives for future research and development will be discussed, together with the physical and operational constraints that new mine communication systems must face.

Jan 1, 1973

In 2007, a total of 14,871 mining operations reported employment data to the Mine Safety and Health Administration (MSHA).1 Almost half (48.4%) were sand and gravel mines, followed by stone mines (31.2%), coal mines (13.7%), nonmetal mines (4.9%), and metal mines (1.9%).

Aug 1, 2009

By Vernon O. Markworth

This report contains the results of tests performed on three large diesel engines to determine their ability to meet selected criteria of the Mining Enforcement and Safety Administration Regulations for equipment used in gassy, non-coal mines. Study efforts were first directed toward determining the types of equipment expected to be used in underground oil shale mines. Three typical engines in the 800-1200 horsepower range were then selected for testing. Intake flame arresters, exhaust scrubbers, and water jacketed exhaust system were designed and built for each engine. During testing, each engine was evaluated for its gaseous emissions output, adequacy of the exhaust gas cooling system, ability to withstand internal explosions, and adequacy of the flame arresters. Surface temperatures of the engine and exhaust cooling system were determined under full load operation.

Jan 1, 1978