Search Documents

By R. H. Grau, A. Sainato, S. J. Schatzel, T. M. Kohler, A. T. Iannacchione

This Bureau of Mines research study found gas emission rates from an advancing face, and flows and pressure of gas from an exploration drill hole were dependent upon the geology of salt encountered in a domal salt mine. Normal production-grade "pure" salt adjacent to an anomalous' zone was found to have a methane emission rate of less than 5 ft3/ ton (0.1 m3/t) of mined salt from a room advanced by a continuous miner. Extremely low gas flows [less the 4 ft3/h (0.1 m3/h)] and lack of pressure buildup were also observed from this normal salt in a 154-ft (47-m) exploration drill hole. These data indicate that methane emissions should not be a problem when mining in this type of salt. In the adjacent anomalous zone, methane emission rates ranged from 15 to 70 ft3/ton (0.4 to 1.8 m3/t) of mined salt from an advancing face. Gas flows of approximately 42 ft3/h (1.2 m3/h), and pressures in excess of 900 psig (6,200 kPa) were observed in an exploration drill hole when the anomalous zone was encountered. This information suggests a greater methane emission hazard from the anomalous zone than from the associated normal salt. If this trend of increasing emissions problems associated with anomalous zones of salt is common with similar anomalous zones encountered or observed in other domal salt mines, then special control strategies should be employed to minimize this potential mining hazard.

Jan 1, 1984

By H. C. Fuller

Submerged combustion and inverse solubility methods were investigated as promising alternative means for crystallizing manganese sulfate from solutions produced by leaching manganese ores with either sulfuric acid or sulfur dioxide. Evaporation of water from typical manganese sulfate solutions by sub-merged combustion techniques enabled production of a slurry containing 32 to 39 pct MnSO4.H2O crystals suspended in a saturated solution of manganese sulfate. Such a slurry required further processing by thickening or filtration and drying to produce crystals of MnSO4.H2O. In a second approach, semicontinuous processing of manganese sulfate solu¬tions by thermal crystallization under pressure effected a recovery of 94.5 pct of the MnSO4.H2O as dry free-flowing crystals. Treatment of a solution containing about 100 grams manganese per liter at 189° C, produced a "barren" solution containing only 1.9 grams manganese per liter. Calculations made on comparable manganese sulfate solutions show that the heat requirement of the thermal crystallization method was about one-third to one-fourth that of the submerged combustion method.

Jan 1, 1966

By Lloyd Williams, R. E. Hershey, B. W. Gandrud

"1. The investigation shows that the Sewanee bed is the only bed of major importance in Marion County, 97 percent of the coal mined in the county having come :from this bed. There are coal reserves in minor quantity in the Battle Creek bed, and production from this bed depends on a few small truck mines. The Richland bed, or Lower Sevanee has been mined in the past, but no coal has been produced from it in late years. There are no production records of any other beds in the county, although some coal has been produced from them.2. Known measured and indicated reserves in all beds, based on a minimum thickness of 14 inches and on l,800 tons per acre-foot of coal in place, are estimated to be 61 million short tons as of January 1, 1953. Of this total, 55 million short tons is in beds 28 inches and more thick. Areas in each bed ·were omitted from the estimate where available data relative to the bed characteristics are too meager to permit making an estimate that conforms with the definitions of measured and indicated coal adopted for this study. Should future drilling or development prove reserves in these areas, such reserves should be added to the total estimated reserves.3. Recoverable reserves of coal are estimated in beds 28 inches and more 'thick. This recovery is based on total thickness of coal in the bed (less partings 3/8-inch thick or more), rather than on the thickness of the coal actually mined. This thickness is about the minimum now being mined by hand loading onto conveyors in the Appalachian Region. The combined weighted average recovery for the Sewanee and Battle Creek beds in Marion County, as determined by this investigation, is 60.9 percent. Based on this, the recoverable reserves of coal in Marion County are estimated at 34 million tons."

Oct 1, 1955

By James H. Cobbs

The utilization of large diameter drilled holes for mine shafts seems to have had its beginning in Europe about 1850 (28) where the mining industries of Germany and The Netherlands first used drilled shafts. Recent shafts in softer formations of diameters as large as 25 feet and as deep as 1, 700 feet have been drilled in both The Netherlands and Germany. The first shaft drillers utilized cable tool or churn drilling techniques which limit both hole diameters and drilling speeds. Though some churn drilling of shafts is still performed, rotary drilling has been the dominant technique for many years.

Jan 1, 1973

By J. J. Taber

This is the final report on Grant No. G0144067. The report presents the results of a number of laboratory studies carried cut in several different ways to determine the effectiveness of foam for blocking the flow of gas in coal. The effectiveness; (of foam for retarding or blocking the flow gas in various porous media has been observed by many investigators1-4 but we are not aware of similar detailed studies in coal. Because of the diversity of our experiments, the key findings and general conclusions are presented very briefly in Section II. As a convenience to the reader a complete table of cements is included to enable the reader to find those experiments and studies of greatest interest.

Jan 1, 1976

By Allen S. Smith

Analysis of the helium content of a natural gas presents more than the usual difficulties encountered in applying the thermal--conductivity method because of the relatively small amounts of this inert gas present and the wide variation in the other constituents. However, the numerous advantages of this method and its adaptability to continuously recording and control instruments make it worthy of consideration. A specific application of the method described yields quantitative results only when used with gas mixtures of known qualitative compositions which vary within predetermined limits. Periodic analyses for the helium content of a producing gas well may be conveniently made by an absorption method3/ and a continuous analytical method is not necessary for this purpose. Natural gas containing 1.75 to 1.90 percent of helium produced from Government-owned wells is processed in the Amarillo (Texas) Helium Plant of the Bureau of Mines. The helium extracted in the plant is supplied to the Army and Navy, and the processed natural gas is sold to a commercial gas company4/. As complete recovery of the helium in the raw material is not economically practicable, the processed gas contains 0.1 to 0.3 percent of helium, depending upon conditions of operation;- Production is checked against the helium removed from the gas, which before the installation of the thermal--conductivity apparatus was calculated from the analysis of a cumulative sample of the processed gas. As conditions of operation affect the residual helium content to a large extent, a composite sample was an uncertain index of the efficiency of the process.

Jan 1, 1934

By Kenneth Eilerts

[Efficient and econonic production of ?etroleum requiros knowledge of the propertios of rescrvoir fluids a:$. their characterintics of flow throayh porous forclntions. The cllanga in propertie s and flow characteri s- tics of fluids when their corosition is altercd cs a rnsult of reservoir- pressure decliae is of 'mecial i~ortenct? ir, planning wall-spaAng pro.yama and production schedules. Rct~ntion of the ~eatent poscible quantity of dissolved gac in the rescrvoir liquid gnneml'y is recognized cs ess~ntisl to mxim ultimzte recoverj of oil fro3 the underground reecrvoir. Ilo:rever, pro6uction mothodn tending to mintain gis in solution in the oil and re- sulting in the optimm ocolo~ic recgvery of oil not only vary from field to fiold but also my have to be changed from time to time in a given field as it is being depleted of its recoveraklo oil. Const vestly there is need tc investigztc tY.e propertiec of resa:-voir f kids corresponding to successivc stages of reservoir depleJ&ion with the view of obtnining infomation oacential to efficient prcriuctian practices.]

Jan 1, 1939

By D. Harrington

The number of fatalities from mine explosions for the fiscal year 1945 dropped below that of the year before; continued improvement over the record of the years from 1940 to 1945 is hopeful, but the number of reported explosions has increased rather than diminished, and the number of victims claimed by explosions is often more definitely a factor of chance than forethought. Mine fires and explosions can be eliminated through the methods now well-known to those well-informed in matters pertaining to safety in mining but ignored by many coal-mine operators and employees who follow procedures of the past or their own short cuts, regardless of disasters that may result: Tried and proved safety measures for preventing mine fires and explosions have been recommended to the mining public repeatedly, yet only a relatively small but far-sighted minority have adopted these measures and made them a part of operating practice. That far more explosion disasters did not occur in 1945 is fortunate. In 1945 a coal-mine fire of electrical origin caused heavy loss of life, while several others from the same cause were controlled with but few fatalities; this hazard is now being curbed temporarily to some degree after the bad record of the two preceding years, but a real solution of the problem has not been reached, although cooperating committees trying to produce at least some answer have made progress.

Jan 1, 1946

By Edward D. Thimons

The Bureau of Mines conducted a state-of-the-art study of techniques currently employed to close large openings in underground mines. A large opening was considered to be any opening over 10 feet high and having a cross section of at least 200 square feet. Five salt mines and one limestone mine were visited to observe various methods of sealing large openings. Because of the variations in conditions from mine to mine, no definite conclusions could be drawn as to which is the best method. In mines where waste material is available, stoppings built by piling waste material are efficient and economical. Where waste material is not available properly constructed brattice cloth stoppings are superior to those built from wood, concrete block, or urethane foams.

Jan 1, 1975

By William C. McLaughlin

In the deep vein mines of the Coeur d'Alene mining district, rock bursts are a potential hazard to the mine structure and underground personnel. Damage repair costs are estimated by one company to exceed $1 per ton of ore mined. The Bureau of Mines, in cooperation with the mining companies, has conducted research intermittently over the past 10 years to help reduce bursts. Onsite inspections of major rock bursts were conducted, and reports were submitted to mine management; these included the geology and geometry of the affected area. The paper discusses the development and improvement of microseismic and surface monitoring equipment. The underground microseismic network, when operated on a regular basis and the results plotted daily, is capable of detecting stress concentration in certain areas. The surface seismographs record rock bursts, blasts, earthquakes, etc., throughout the district and show approximate location, time, and relative intensity of the event.

Jan 1, 1976

By H. G. Iverson

The purpose of this investigation was to beneficiate the Talladega gray iron ores by flotation. A component of the problem was the determination of the degree of beneficiation possible by flotation as well as the relative selectivity of certain reagents in promoting flotation of either the iron minerals or the siliceous gangue minerals. The scope of the present investigation involved only the use of small-scale laboratory equipment. Treatment by roasting and magnetic separation was not included in this study, inasmuch as a similar comprehensive investigation was completed and the results were published by the Bureau of Mines in 1927. The results of the work on Talladega iron ores are briefly summarized in this report. In the search for efficient and economic methods of beneficiating low-grade iron ores, the flotation process is among those that are receiving considerable attention. The Talladega ores are of particular interest for a flotation study, because they contain two iron minerals (magnetite and specular hematite) that are somewhat dissimilar in their flotative response.

Jan 1, 1949

By Douglas A. Crum

The Taylor's friction circle method for slope stability analysis can be extended to incorporate multiple circles defining the slip surface in a failure mechanism so that it is a workable method for bearing capacity calculations of foundations and rotational failures of retaining walls and similar structures. The U.S. Bureau of Mines has further extended the multiple-circle method to include friction in the material strength and to utilize computational schemes such that this method can be programmed with optimization capabilities rather than being used as a graphical or semigraphical method. Some examples are given that demonstrate ultimate bearing capacity calculations of embedded foundations with eccentric loads and nearby slopes.

Jan 1, 2010

By Robert L. Lagace

The purpose of the work reported herein was to investigate whether available telephone multiplexing equipment offered a means to rapidly upgrade the traffic-handling capacity of present mine telephone systems and provide for selective calling for safer and more efficient mine operation. Common sense was used to decide whether or not an item could be termed "available." Since conventional telephone gear is not designed to interface pager phones for example, existing shelf items would require adapters to compatibly interface these two types of gear for independent operation over the present single twisted pair used in mines. These and similar small items were allowed, but if a system required any extensive design work to adapt it for the mines, we ruled it "not available."

Jan 1, 1975

By Donald S. Colby

This Bureau of Mines report is essentially a handbook, or manual, for making the type of mineral resource valuation commonly required for such public policy problems as mineral leasing. The principle of resource valuation through the capitalization of cash flow is well established. A mathematical procedure, based on a simplified accounting system, is detailed for calculating cash flow from revenue, plant costs, and operating expense. Variations of procedure cover cost depletion, percentage depletion, and depletion limited to 50 percent of net income. The influence of the depletion provisions of the tax regulations on the value of a resource to an owner and to an operator is analyzed. The relationship of royalty, bonus payments, and sales price to resource value is also described, and methods for approximating resource values using these payments as input data are developed.

Jan 1, 1969

By Douglas A. Donato

This Information Circular presents the MULSIM/PC system of numerical modeling computer programs developed by the U.S. Bureau of Mines. This system consists of four programs: PREMUL, the preprocessor or mesh generator; MULSIM/PC, the actual numerical modeling program (number cruncher); MUL3D, a three-dimensional postprocessor; and MUL2D, a two-dimensional postprocessor. These programs were specifically designed to operate on IBM-compatible (MS-DOS-based) personal computers for easy transfer of this technology to the mining industry and academia. MULSIM/PC uses a subvariation of the boundary-element method, namely, the displacement-discontinuity technique, for linear-elastic geomechanical analysis of mine plans in one or two parallel underground tabular deposits. Results calculated by this technique include stresses and displacements as they relate to changing mine geometries and materials. In addition to describing the MULSIM/PC program and its features, and providing a detailed example model, this report also documents the associated preprocessing and postprocessing programs that are part of the MULSIM/PC system. User's guides for all the programs are contained in the appendixes following the main report.

Jan 1, 1992

By Lloyd H. Banning

With the ever-increasing demand for energy in all forms, electrical energy generated from geothermal resources could become an important energy source in the next few decades. Geothermal fluids, which contain appreciable quantities of dissolved salts and gases, are generally corrosive to materials of construction. Since data on corrosion of materials in geothermal brines is limited, the literature was surveyed through February 1972 to obtain a compilation of information on corrosion resistance of aluminum and its alloys, copper and copper-base alloys, carbon steel and cast iron, stainless steels, chromium-iron alloys, nickel-and cobalt-base alloys, and titanium in heated brines including sea water.

Jan 1, 1973

By W. A. Grosh

The Piquette Mining and Milling Co, operates a zinc mine and concentrating mill in the Upper Mississippi Valley zinc-lead district near Tennyson, Wis. The principal ore mineral is zinc sulfide, which occurs in limestones and dolomites of the Decorah formation. Exploration in the district is by churn drilling from the surface. An adit at the base of the ore zone provides access to the mine. A room-and- pillar mining method with irregular pillars is used. Drilling is done with Jumbo-mounted drills. The broken ore is loaded by crawler-mounted front-end loaders into diesel-powered trucks for haulage direct to the mill.

Jan 1, 1959

By C. W. Owings

"PURPOSE OF REPORTMany bituminous coal-mine officials realize that coal dust presents an ever-present coal-mine explosion hazard, and that persons forced to breathe large quantities of it may be more subject to respiratory infection than persons working in less dusty atmospheres. As an outgrowth of the realization that coal dust should be allayed at its source, many mining companies have expressed the desire to install dust-allaying equipment, and in a number of mines, water or wetting solution is being applied on the cutter bars of mining machines, on mobile loaders, belts or conveyors underground, and tops of mine cars. Spraying equipment also has been installed on dumps to allay dust during dumping operations. Dust-allaying equipment has not been standardized, however, because manufacturers have found that many prospective purchasers of such equipment have different ideas. These manufacturers wish to standardize, so far as feasible, the types and placement of such equipment. Many mine officials, although interested, do not know the best or most effective methods for allaying dust.For a number of years the Bureau of Mines has advocated allaying dust by applying water or, more recently, water modified by a wetting agent on the cutter bar of mining machines and by applying water to loaded and empty mine cars in order to keep as much dust as possible from spilling onto the haulage roads. In recent years this Bureau has also advocated applying water with or without a wetting agent during mechanical loading of coal and during unloading of coal from trackless cars or buggies and from elevating conveyors. It has now become apparent that specific arrangement of pipes, hose, and nozzles should be standardized to at least some extent. It is the purpose of this report, therefore, to give in detail suggested arrangement of dust-allaying equipment in the hope that both manufacturers and mine officials will have available dust-allaying equipment with maximum efficiency to do the desired work."

Nov 1, 1945

By B. J. Moore

This publication contains analyses and related source data for 252 natural gas samples from wells and pipelines in 17 States. All of the samples were obtained and analyzed during calendar year 1976 as a part of Bureau of Mines investigations of the occurrences of helium in natural gases of countries with free market economies. This survey has been conducted in the United States by the Bureau of Mines since 1917. In late 1965, the survey was expanded to include foreign gasfields. The analyses published herein were made by mass spectrometer and a special helium analysis apparatus, which are described in Bureau of Mines Bulletins 4862 and 576.3 The results of the investigation of the occurrences of helium are published annually to make the information available as soon as possible to the gas industry and the public in general. Eighteen previous publications have presented the results of 11,065 gas analyses prior to 1976. The first 3, Bulletins 486,4 576,5 and 617,6 contain analyses and related source data on 5,218 gas samples collected from 1917 through 1960. The other 15

Jan 1, 1977

By Richard N. Spencer

Electric-furnace smelting for simultaneous recovery of zinc spelter and lead bullion from complex lead-zinc sinter was investigated. Reduction of lead and zinc was satisfactory. Condensation of lead and zinc vapor to pyrophoric metal powder in a water-cooled, shock-condensing system produced excellent recoveries. Metal-splash condensation to produce zinc spelter was unsatisfactory. Special smelting experiments differentiated the effects of several smelting parameters on zinc metal recovery. The principal cause for unsatisfactory zinc metal recovery was transfer of iron to the condenser and subsequent degradation of zinc in a mixture composed of lead and an iron-zinc intermetallic compound. Limitations of the process were determined. Slag-resistance open-bath electric smelting of complex lead-zinc sinter is not considered feasible.

Jan 1, 1967