Search Documents

By Fred W. Johnson

The first section of this circular has been prepared with a view to answering inquiries frequently received by the Bureau regarding laws governing the staking of claims and regulations covering requirements for holding them and obtaining title in fee to placer ground. These laws and regulations were summarized briefly in Information Circular 6796, "Placer Mining in the Western United States." These laws, however, are administered by the General Land Office, Department of the Interior, and it has been considered advisable to combine an authoritative résumé thereof by the Commissioner of that Bureau with information on small-scale placer mining previously published by the Bureau of Mines. The second section of this circular is largely a revised reprint of Information Circular 6611, "Small-Scale Placer Mining Methods", first published in April 1932 for the purpose of answering the many daily inquiries then being received on this subject. This circular has been reprinted repeatedly, and about 30,000 copies have been distributed, most of them in response to applications therefor. At present (June 1937) requests for this publication continue to be received daily.

Jan 1, 1938

By Joseph T. Singewald

The possible value of the red hematite iron ore of the southern Appalachian States, if some practicable method of concentrating it could be devised, has long been recognized. The ore is very low grade, and although in enormous quantities, particularly in the States of Alabama, Tennessee, and Georgia, is only at a few points rich enough to work, and even the best of it ranks among the lowest grade iron ores being mined in the United States. A cheap method of beneficiating this ore would make enormous quantities available and vastly increase the iron-ore resources of the country. However, this low-grade ore in effect constitutes a potential iron reserve, and as long as ample quantities of ore can be obtained elsewhere the question of its utilization does not demand immediate notice. Where these ores are in part of workable grade, however, a problem of more immediate importance arises which, from considerations of economy and prevention of waste in their mining, ought to be solved or, at least, attacked as quickly as possible. Where these ores are being worked they are usually intimately associated with lowergrade material that in mining is left behind. The difficulty and expense of going into ground broken by old workings makes the recovery of this lower-grade ore practically impossible and it is lost forever. Success in concentrating the red ores, therefore, would save material that is now being irretrievably lost. The successful largescale concentration of low-grade ore in the last few years on the Lake Superior iron ranges should encourage the attack of similar problems in the Birmingham district. While studying iron-mining methods in the United States for the Bureau of Mines, Dwight E. Woodbridge, consulting mining engineer of the bureau, was impressed with the importance of this problem, and believed it merited the attention of the bureau. Accordingly, Mr. Woodbridge had Mr. W. J. Penhallegon, general superintendent of ore mines and quarries of the Republic Iron & Steel Co., of Birmingham, send the author of this report five samples of the unworkable siliceous ores of the district. The results of concentration experiments with these ores made a more thorough 'and systematic investigation desirable. In consequence, the author subsequently collected samples in the district, and these became the basis of the experimental work described in this report. The results are published by the Bureau of Mines as a part of its efforts to increase efficiency in the utilization of mineral resources. The experiments were conducted in the geological laboratory of the Johns Hopkins University, Baltimore, Md., with the aid of Raymond Leibensperger, mining assistant. The chemical analyses were made by A. C. Fieldner, chemist, of the Bureau of Mines. The author wishes to express his appreciation of the courtesies extended to him by the mining companies of the district, and particularly to Mr. W. J. Penhallegon, of the Republic Iron & Steel Co. Thanks are also due Prof. W. B. Clark, director of the geological laboratory of the Johns Hopkins University, the unrestricted use of the facilities of the laboratory.

Jan 1, 1917

By Timothy J. Orr, Michael J. Beus, Frank T. Duda

The technology to enhance safety and control features for mine shaft hoists is being investigated by researchers at the U.S. Bureau of Mines (USBM). The objective of the research is to prevent injuries and fatalities related to hoist and elevator operations. Monitoring and controlling mine hoisting operations will allow hoist operators, inspectors, and maintenance personnel to increase their awareness of potentially dangerous situations and provide controls for safer operations. Process simulation and visualization software, real-time data sensing, and advanced programming techniques are being applied to this problem. Development of reliable and cost-effective sensors and data acquisition interfaces to monitor hoist loads and detect slack rope conditions is underway. Three-dimensional design software was used to visualize mine hoisting to enhance understanding of hoist operations. Quick Basic and Visual Basic (an object-oriented Windows interface) are being used for acquiring and processing hoisting data. Testing and evaluation of components are underway at USBM testing facilities. The resulting system will allow hoist personnel to assess critical operating parameters, such as hoist position, speed, acceleration, conveyance load, and rope tension.

By D. L. Soreck

The hazards to the public posed by abandoned mine shafts are well documented. As private development encroaches on previously mined areas, the potential for fatalities and serious injuries from abandoned mine shafts increases. The U.S. Bureau of Mines has conducted research into cellular concrete as a material for sealing these openings. The current work involves testing the characteristics of cellular concrete before and after it had been pumped or dropped from different heights into a simulated mine shaft. Cellular concrete was pumped vertically up to and subsequently dropped from heights of 18 and 37 m into concrete forms. Wet density measurements were made at multiple sampling points in the test circuit. Air content determinations and uniaxial compressive strength testing were conducted. Research results showed significant loss in air content and changes in the characteristics of cellular concrete during pumping or dropping from various heights. Recommendations on effective use of cellular concrete for sealing abandoned mine shafts are made.

Jan 1, 2010

By D. Harrington

The record of fatalities from mine explosions in the United States during the past 3 years has been the best in the history of the mining industry. During these 3 fiscal years, mine explosions have resulted in an average of 4I0 deaths per year, as compared with an average of 153 deaths per year for the preceding; 5 years; an average of 542 deaths per year for the 3-year period 1907-09, inclusive, just before the organization of the U. S. Bureau of Mines; and a yearly average of 265 deaths per year for the 20-year period prior to 1929. This remarkable reduction in deaths from mine explosions demonstrates clearly that mine explosions can be controlled; in fact, they can be prevented when or if the mining people of the United States see fit to take the readily available precautions necessary to bring about this desirable objective. Several large coal-producing States, which in the past have had numerous disastrous explosions, have been free from such disasters for continuous periods of as much as 6 years or even longer. The bituminous mines of Pennsylvania, the largest coal-producing State, give a good example of what can be done to prevent explosions; this State has had only one major explosion (and it resulted in 7 fatalities) during the past 6 years, and no explosion occurred in the several hundred bituminous-coal mines of the State during the past fiscal year. This is a truly remarkable record when compared with past performance in any year in the operation of coal mines in Pennsylvania.

Jan 1, 1936

By M. C. Irani

This study is a survey of supply and demand for minerals, metals, alloys, and compounds used by the chemical industries in the Ohio River Basin (ORB) area of Ohio, Pennsylvania, and West Virginia during 1967. Data for the study were obtained from completed questionnaires received from chemical manufacturers and from interviews with officials of chemical companies and mineral producers and distributors. The information includes kind, quality, quantity, values, sources, specifications, uses, and methods of transportation. Results of the study show that of the total value of mineral materials consumed by the chemical industry, manufacture of inorganic chemicals consumed 46 percent; fertilizers, 22 percent; and soaps and detergents, 19 percent. Fifteen commodities accounted for 91 percent of the total value of mineral materials consumed. Five of these--phosphates, potash, salt, sulfur, and titanium dioxide--accounted for 59 percent of the total.

Jan 1, 1970

This report is the 22d in a series summarizing Bureau of Mines research and technologic work on coal and related investigations.2 3/ A summary of work published during 1957 and of work in progress is presented. Details regarding the subjects treated in the publications may be found by referring to articles cited in the footnotes. The objective of the coal work of the Bureau of Mines is to obtain information that will lead to improved production and utilization of coal, thus conserving a most important national asset.4 5/ Though studies of mining methods and exploration of various coalfields ma; contribute directly to improved production, no less so does the work in health and safety. The many problems relating to chemical and physical properties of coal reflect the need for an understanding of these properties for the most effective use of coal in its various fields of application and for the development of new methods of processing coal. Studies of existing and proposed processes of combustion, carbonization, gasification and hydrogenation of coal are necessary for increased efficiency in its use. Engineering service provided by the Bureau is of direct value in the conservation program in preventing waste. Stations where the main coal activities of the Bureau are carried out are shown in the following list:

Jan 1, 1959

By Launa Mallett, Charles Vaught, Michael J. Brnich

Purpose: This training material focuses on the content of emergency warning messages. Research has shown that when an emergency occurs, people often do not get the information they need for the purpose of taking appropriate action. This safety talk presents a procedure, using mental cues that can be used by senders and receivers of emergency warnings. Intended Use: This material has been developed for use in short safety-training sessions such as start-of-shift safety or Atoolbox@ talks. The information can be presented in approximately fifteen minutes and is appropriate for workers at all experience levels. While the examples and illustrations are taken from the underground coal mining industry, the training can be tailored to any work setting by substituting appropriate examples. Materials Needed: The instructor will need to prepare the figures provided in a form that can be seen by the entire class. Suggested methods include the use of: (1) overhead transparencies, (2) laminated pages that can be held up for small groups, and/or (3) handouts with copies of the figures for each trainee. As a supplement, stickers featuring the communication triangle can be placed on hard hats, telephones or other communication devices to remind workers about the key to effective emergency communication. The Talk: The accompanying script is a guide for presenting this safety talk. Training is enhanced if these materials are covered but not simply read by the trainer. Examples given in this guide are from real experiences. To make training more interesting and effective, the instructor can substitute examples from his/her workplace. Additional Resources: The following references will provide further information about communications during emergencies. Auf Der Heide, E. (1989). Disaster Response: Principles of Preparation and Coordination. The C.V. Mosby Company, St. Louis. Mallett, Launa, Charles Vaught, and Michael J. Brnich Jr. (1993). A Sociotechnical Communication in an Underground Mine Fire: A Study of Warning Messages During an Emergency Evacuation@, Safety Science, 16, pp. 709-728. Nigg, J.M. (1987). A Communication and Behavior: Organizational and Individual Response to Warnings@ in Sociology of Disasters: Contributions of Sociology to Disaster Research, R.R. Dynes, B. De Marchi, and C. Pelanda (eds.), Franco Angeli, Milan, Italy, pp. 103-116.

Jan 10, 1999

By Donelson A. Robertson

Literature was searched and cases of alleged water well damage were investigated. Occurrence of ground water in Appalachia is primarily in low yield, fractured, water table aquifers. Four test sites were chosen based on geographic and geologic diversity. Test wells were drilled at each site and base line data on water quality, static water level, and drawdown characteristics were obtained before surface mining commenced. Blast induced ground vibrations were measured at the surface by the wells at levels up to 5.44 inches per second maximum resultant particle velocity. Measurements made at the bottom of wells indicated that vibrations were considerably attenuated at depths of 140 to 160 feet. No direct evidence of change in water quality or well performance was produced by blast vibrations, but removal of downslope support by excavation does cause lateral stress relief which permits the water-bearing fractures to become more open. This additional storage capacity causes the static water level to drop and for well-bore permeability to improve. Static water level recovers if sufficient recharge is available and well performance is

Jan 1, 1980

By A. O. Ipsen

As part of the Bureau's intensive investigation of domestic manganese deposits, lots of ore for testing were collected by Bureau engineers during examinations of several properties in Juab County, Utah. One low-grade and two intermediate-grade samples (13.5, 25.3 and 27.5 percent manganese) were procured by engineers of the Bureau of Mines from the 900--and 1,100-foot levels of' the Tintic Standard mine, situated 2 miles southeast of Eureka, Utah. The ore bodies were described as blocks of ore approximately 60 feet long, 40 feet wide, and 20 to 100 feet deep. The manganese-iron association in the Tintic Standard ores was intimate, and no significant concentration of the low-grade sample was made by ore dressing, However, both of' the higher-grade samples were readily beneficiated to marketable manganese products. Ore from the Oxen No. 5974 claim, 2 miles northeast of Eureka, Utah was low in grade (19.4 percent manganese) and was not amenable to the production of high-grade concentrates owing to the intimacy of association of the manganese minerals with silica. However, a fair manganese recovery was obtained in a product that, when sintered, assayed plus 40 percent manganese. The ore body is reported to be a replacement in limestone and is composed of manganese oxides intermixed with silica, decomposed rhyolite, and limestone. The Fields property consists of five mineral claims situated 3 miles north of Eureka, Utah. The deposit is a replacement in a contact between limestone and a quartz dike. Tests were made on representative samples of a 50-ton lot stored on the property. Although the mineral association in the ore (22.2 percent manganese) is not particularly complex, the physical properties of the manganese minerals render the ore refractory to ore-dressing beneficiation. As the ores varied widely in physical and chemical characteristics, samples from each property were considered as separate ore-dressing problems.

Jan 1, 1949

By Jr. Koch

As a part of a larger study of the distribution of metals within ore deposits, the geometry of distribution of gold, silver, lead, copper, and zinc in five veins of the Fresnillo mine, Zacatecas, Mexico, was established. The purpose was to obtain basic data necessary for evaluation of geological theories about processes of vein formation and useful for practical mining applications in ore estimation and prediction of ore beyond present workings. The Bureau of Mines investigation comprised statistical analysis of 64,000 assay values from some 16,000 mine samples. The samples were taken at 2-meter intervals in drifts exposing the veins through a vertical range of some 750 meters. Within individual veins, the metals are distributed in dome¬like patterns with highest metal contents tending Lo occur in oreshoots at the centers of the developed parts of the veins. However, in the block of ground containing all five veins, base metals define mathematical domes with highest contents near the center; precious metals define mathematical basins or troughs with low contents near the center. The ratio of silver assay values to lead assay values corresponds to two geographically distinct types of mineralization: one in which silver is closely related to lead, and another in which silver is independent of lead. Other metal ratios also vary regularly from one place to another. The statistical methods employed in this study would be useful for other geologists or engineers who need to analyze large amounts of assay or similar numerical data.

Jan 1, 1967

By James M. Link

Underground coal mining is the most hazardous industrial occupation in the United States.. Haulage accidents in underground coal mines contribute substantially to the occupational hazards of this type of work. In an effort to improve mine safety, a completely hydraulic transport system has been designed to move coal from the mine face to the preparation plant. The capital investment for the hydraulic haulage system is great, and the size of the mine developed for this study is large. Mine production for the conventional haulage mine is 1. 1 million tons of clean coal per year, while the hydraulic haulage mine will produce over 1.6 million tons of clean coal per year. Safety statistics for a number of mines of this size are shown.

Jan 1, 1975

By Charles G. Howard

Accidents involving underground rail transport were analyzed to quantify the magnitude and the operational requirements for individual mine car braking systems. The results showed that the brake preventable accidents represent only 2% of the total underground fatal accidents and less than 1% of the total underground nonfatal accidents. In addition, the brake preventable accidents are expected to decline over the next decade. The costs of accidents involving deaths and Injuries were determined using various well accepted methods. The costs of a brake retrofit program for all operating underground coal cars were developed separately for small and large coal mines. Costs of retrofit brakes, new car brakes, maintenance, inspection and repair facilities were included in the esimates. The analysis showed that a retrofit program would not significantly increase safety, and that the program cost would greatly exceed the corresponding expected benefits.

Jan 1, 1979

By M. Kawahata

Methane sensors using principle of catalytic oxidation of methane are employed for determination of methane content in ambient air of coal mines. Certain foreign gases or vapors in the air poison the catalyst of the sensor effecting the sensor's response. After literature search of poison compounds of Pt and Pd oxidation catalyst, experimental studies of catalyst poison kinetics were made for three siloxane compounds, tributyl-phosphate, monobromotrifluoromethane, and hydrogen sulfide, selected as poison vapors. Concentration range of the poison vapors was varied in a range from 3000 to 0.1 ppb (v/v). Three siloxane vapors produced strong catalyst poison effect, followed by tributylphosphate, hydrogen sulfide and monobromotrifluoromethane for the high concentration level of the poison vapors. The poison effects are influenced significantly by concentration of the vapors. Threshold poison vapor concentrations where effect of the poison vapors on the sensor is minimal were determined experimentally. Experimental studies were made further for prevention method of catalyst poison by adsorption techniques. Use of activated carbon cloth inserted on the sensor's head prevented catalyst poisoning efficiently.

Jan 1, 1981

By Ann G. Kim

Fires that occur in abandoned coal mines, waste banks, and in coal outcrops constitute a serious health, safety, and environmental hazard. Toxic fumes, the deterioration of air quality, and subsidence constitute the greatest hazards from these fires. Although tires on abandoned mined land (AML) occur in every coal-producing state, the severity of the problem varies. Methods to extinguish or control AML fires, including excavation, fire barriers, and sealing, are generally expensive and have a relatively low probability of success This U.S. Bureau of Mines report includes information from a variety of sources, i.e., agencies of the Federal Government, State agencies, research reports, conference proceedings, product information, and technical literature. This information has been collated into a comprehensive discussion of AML fire problems. Data on past fire control projects and on the estimated extent of the current problem have been compiled. Factors affecting the occurrence, propagation, and extinguishment of AML fires are discussed. Conventional fire control methods are described, and their probable effectiveness is evaluated. Information on the hazards of AML fires and safety considerations is included. The status of current technology, recent improvements in fire control methods, and areas of current research are discussed.

Jan 1, 1993

By John C. Cook

This was a study to identify and evaluate known technologies employing electromagnetic resonance phenomena in solid minerals for their identification and assaying, particularly assay logging of exploratory boreholes. A comprehensive literature search and study revealed some little known NMR (nuclear magnetic resonance) techniques developed by Professor G. J. Béné's group at the University of Geneva, Switzerland. These are suitable for use in weak, inhomogeneous magnetic fields. Laboratory NMR tests of numerous U.S. ore minerals showed good identifying signals from phosphates, fluorspar, bauxite, oil shale, and spodumene (lithium) ores, but not from the copper, lead, antimony or manganese ores tested. Use of EPR "signatures" for such ores is suggested. A conceptual design for an NMR assay logging system is proposed.

Jan 1, 1978

By Ott F. Heizer

This paper describing the mining practices at the mines of Massachusetts, Massachusetts Co., Inc., at Mill City, Nev., is one of a series being prepared by the Bureau of Mines on mining practices, methods, and costs in tie various mining districts of the United States. The author acknowledges the assistance of William C. Vanderburg, associate mining engineer, U. S. Bureau of Mines, in the preparation of this paper.

Jan 1, 1930

This report provides the results of an industrial engineering study that assessed the safety and efficiency of underground ore handling in U.S. metal mines. One of the primary findings of the study was the improvement needed in controlling muck size in the ore handling stream. Oversize ore causes much additional labor, creating work stoppages and is a principal cause of accidents in metal mines. This report includes data on block caving, back cut and fill room and pillar, shrinkage stoping, and sublevel stoping.

Jan 1, 1974

By H. P. Greenwald

[In many coal-mining countries, during he pest decade, there have seen made extended studies and accurate measurement of movement of roof strata, tests of the physical properties of specimens cut therefrom, and tests of the strength of end load on artificial supports. Naturally, such studies have been more extensive in European countries, where mining conditions are less favorable than in the United States. As a part of its work in the conservation of coal resource and prevention of accidants in mines, the Bureau of brines began systematic measurements of the movement of roof strata to in coal mines in the fall of 1935. It was decided- that, in the beginning, work on a rapidly retreating rib line in a mechanized mine would give the greatest amount of information in a reasonable time. To this end w cooperative tine agreement was made with the Pittsburgh Coal Co., through Dr. L. E. Young, vice: president in charge of operations, for conduct of work in that company's Montour 10 mine operating in the Pittsburgh coal bed. This paper gives an account of the methods used in the investigation, excerpts from the data obtained, and such generalizations as appear to be justified.]

Jan 1, 1937

By H. P. Greenwald

[In many coal-mining countries, during he pest decade, there have been made extended studies and accurate measurement of movement of roof strata, tests of the physical properties of specimens cut therefrom, and tests of the strength of end load on artificial supports. Naturally, such studies have been more extensive in European countries, where mining conditions are less favorable than in the United States. As a part of its work in the conservation of coal resource and prevention of accidents in mints, the Bureau of Mines began systematic measurement of the movement of roof strata to in coal mines in the fall of 1935. It was decided that, in the beginning, work on a rapidly retreating rib line in a mechanized mine would give the greatest amount of information in a reasonable time. To this end a cooperative agreement was made with the Pittsburgh Coal Co., Dr. L. E. Young, vice president in charge of operations, for conduct of work in that company's Montour 10 mine operating in the Pittsburgh coal bed, This paper gives an account of the methods used in the investigation, excerpts from the date obtained, and such generalizations as appear to be justified.]

Jan 1, 1937