Search Documents

By Millard M. Gilkey

This Bureau of Mines report presents results of a detailed study of water usage in the Wyoming mineral industry along with projections for the future In 1964, the mineral industries of Wyoming used 20 billion gallons of new water, nearly all self-supplied, and reused 72 billion gallons, a total usage of 92 billion gallons. Consumption amounted to 2.8 billion gallons. About one-half of the 20 billion gallons of new water was obtained from [srface] sources and the rest from ground water. Reported costs, covering power and maintenance, for the self-supplied new water at mineral industry operations ranged from less than 1 cent to 20 cents per thousand gallons and aver-aged 8 cents. At one mineral-related operation, water was hauled by truck to supplement a well supply. The cost was $2.00 per thousand gallons delivered. However, the supplemental requirement was only 10 gpm. Cost figures for the recirculation of water, covering power and maintenance, averaged 2 cents. In terms of water usage, the value of product for the entire industry was $25 per thousand gallons of new water intake and about $180 per thousand gallons consumed. The study revealed that Wyoming has a water deficiency but that the shortage is less severe than in the arid Southwest. Projection of the water needs of the Wyoming mineral industries indicates that the demand for new water will increase from the 20 billion gallons used in 1964 to 25 billion gallons in 1980, a 25-percent increase. The projected new-water requirement for the year 2000 is 40 billion gallons, a 100-percent increase compared with the 1964 figure.

Jan 1, 1967

By Stephen R. Iverson

Manganese deposits exist in the Wonder Mountain RARE II area (fig. 1). The manganese mineral is primarily bementite, a silicate. It occurs with Jasper and manganese oxides in tabular or irregular lenses along the contact between red limestone and basalt. There are about 11,000 tons (10,000 t) of indicated sub-economic resources in the northeast part of the study area. Of this, 10,700 tons containing 27.1 percent manganese is at the Apex Prospect and 300 tons averaging 24.8 percent is at the Brown Mule Mine (fig. 1). Another 1,000 tons (900 t) containing 27.0 percent manganese is at the Steel Creek deposit 0.5 mi (0.8 km) west of the area (Wiebelt, 1942, p. 1, 2). Each of these deposits is subeconomic due to small tonnage and high estimated recovery costs. They are in a regional belt of manganese occurrences trending northwesterly through the area. Pardee (1921) reports that manganese ore was shipped from the Triple Trip (Brown Mule) Mine in 1916.

Jan 1, 1982

The development of an onboard contaminant diagnostic monitor to continuously measure contaminant level in a mining machine was advanced to a prototype stage in this contract. Several concepts were investigated and it was found that a static spool type sensor was the most reliable and accurate. Laboratory and field tests showed that an instrument based on this concept is capable of measuring contaminant levels and/or size distribution, depending on the configuration of the sensor. Moreover, this instrument can function on emulsions or homogeneous fluids. Current laboratory equipment can operate on homogeneous fluids only.

Jan 1, 1983

In 2006, a total of 7,178 sand and gravel mining operations reported employment to the Mine Safety and Health Administration (MSHA).1 ? Sand and gravel mines were the largest mining sector, comprising 48.2% of all mining operations. ? Sand and gravel mines were found throughout all 50 states and Puerto Rico.

Sep 1, 2008

By E. R. Bauer

This report describes a U.S. Bureau of Mines investigation into the removal of gate road chain pillars in conjunction with longwall retreat mining. The research objective was to determine, through evaluations of the loads imposed on the gate road pillars and supplemental support elements in the entries, how the pillars, supplemental support, and entries were affected by the longwall abutment pressure. To achieve this goal, vibrating wire stressmeters and hydraulic flatjack pressure cells were installed in the support elements to monitor stress change caused by abutment pressure as a function of longwall face advance. The findings documented in this report are the result of information collected from instrumentation and observation at the mine. Pillar and support loading measurements and stability observations revealed that the roof and the sup- port elements remained stable during panel retreat, while the face progressed at a normal rate of advance. The ability to safely and efficiently mine chain pillars during panel retreat increases resource recovery and can provide several other benefits described in this report.

Jan 1, 1993

By Eliezer Kamon

To finalize the three years granted for the study of miners physiological responses to emergency situations, all the data obtained, were summarized into the following relevant sections; A.. Information on elements of the Man Test required under Subpart 4, Part 2, Title 30 in the Code of Federal Regulation (see Table M-T and Ref. I., Section A). B. Investigation on possible emergency activities, its simulation in the laboratory and the physiologic data obtained on miners performing them This included some studies under cool ambient conditions, expected to prevail in coal mines. C. While in section B the steady state responses have been obtained, time was devoted to establish a unit that will allow data gathering for non-steady state, i.e., transient responses to rapidly changing activities. Section B and C contained elements that were relevant to section A; the Man Test. Therefore some of the information described under section A Man Test, were actually measured during the battery of tests in either section B or in section C.

Jan 1, 1974

By August J. Kwitowski

This Bureau of Mines report summarizes the development of a protective operator compartment for a new generation thin-seam mobile bridge carrier. The developed compartment is commercially available and is currently employed on approximately 15 bridge carriers used in the mining industry. The design of the compartment, which employed human factors engineering and small- and full-scale mockup models, is fully described. Details of the compartment's fabrication, evaluation, and demonstration in a commercial low-seam coal mine are also provided.

Jan 1, 1986

By Charles J. Cohen, Donald F. Reed

"INTRODUCTION AND ACKNOWLEDGMENTSThis report supplements a previous report on work done in this same area 4/ but covers only the period from November 1945 to November 1946. The project was established in 1943 to investigate magnetite deposits in the northwestern Adirondacks by geophysical surveying and diamond-drilling for the purpose of increasing iron production in the eastern United States.In its program of investigation of mineral deposits, the primary objective of the Bureau of Mines is the more effective utilization of our mineral resources, that they may make the greatest possible contribution to our national security and economy. The policy of the Bureau is to publish the facts developed by each project as soon as possible after its conclusion. Maps showing the detailed magnetic surveys of the deposits and anomalies discussed in this report are on open file at the offices of the Bureau of Mines, College Park, Md., and at the University of the State of New York in the office of the Director of the State Science Service, Educational Building, Albany, N. Y.The Mining Branch, Lowell B. Moon, chief, conducts preliminary exami¬nations, performs the actual investigations, and prepares the final report. The Metallurgical Branch, Oliver C. Ralston, chief, analyzes samples and performs beneficiation tests.The chemical analyses included in this report were made at the Eastern Experiment Station of the Bureau of Mines at College Park, Md., under, the general supervision of J. B. Zadra, chief, College Park Division, Metallurgical Branch, and the immediate direction of Dr. Alton Gabriel, in charge of the laboratory service unit."

Nov 1, 1947

By George A. Morgan

The 53 countries that constituted Africa in 1990 accounted for a significant portion of total world output of a number of mineral commodities. Among the most significant to be produced in Africa were andalusite, antimony, asbestos, bauxite, chromite, coal, cobalt, copper, diamond, fluorspar, gold, lithium minerals, manganese, phosphate, platinum-group metals, the titanium minerals-ilmenite and rutile, vanadium, vermiculite, uranium, and zircon. Several of these, chromite, cobalt, diamond, and manganese, were not produced in the United States. Despite the underdevelopment of much of Africa, mineral raw materials playa very important part in the national economies of many of its countries. In many cases, the production of minerals is the dominant economic activity in the country, often having the largest and most sophisticated work force. In several countries, one or two mineral commodities are dominant in a weakly diversified economy. Among these are petroleum and diamonds in Angola, petroleum in the Congo, gold in Ghana, bauxite in Guinea, uranium in Niger, phosphate in Senegal and Togo, and copper and cobalt in Zaire and Zambia.

Jan 1, 1992

By Martin D. Conyac

A mineral resource survey of rock types and geologic structures indicates that the Mt. Henry RARE II area has low potential for the discovery of metallic minerals. Potential for coal and geothermal resources is negligible. Essentially, the Mt. Henry RARE II area has had no claim-staking activity, nor has any mine been developed in it. SETTING Size and Location The 23,000-acre (9,308 ha) "1t. Henry RARE II area (No. 1-666) lies within the Kootenai National Forest approximately 36 mi (58 km) north of Libby, Montana, in the Purcell Mountain; of Lincoln County. Irregularly shaped, the area measures roughly 5-1/2 mi (8.9 km) north-south by 8 mi (12.9 km) Past-west, and lies about 1-1/2 mi (7.2 km) south of the Canadian border.

Jan 1, 1982

By N. Kumar Kittusamy

The purpose of this study was to assess the adequacy of the cab design and to determine the percentage of musculoskeletal symptoms among workers. A questionnaire was designed to assess demographics, work information, job history, and musculoskeletal symptoms in operators of heavy construction equipment. Information concerning equipment included design of the seat/chair, levers, pedals, bothersome vibration, quality of egress from the equipment, proper preventative maintenance and repairs, and age of the equipment. The body regions that were evaluated included the neck, middle/upper back, low-back, shoulder/upper-arm, elbow/forearm, wrist/hand, hip, knee, and ankle/foot. One hundred and eighty nine operators completed the questionnaire. The results indicate that these workers are at risk for developing musculoskeletal disorders, the need to perform a larger survey to further substantiate the outcome, and the need to quantify risk factors (i.e., whole-body vibration and static sitting postures).

Jan 1, 2003

By Kim M. Cornelius

Musculoskeletal injury is a term used to describe a wide range of soft tissue disorders which affect the nerves, tendons, and muscles. Common examples include lower back pain, tendonitis, and carpal tunnel syndrome. The majority of these injuries are not the result of sudden mishaps, but usually develop gradually from repeated wear and tear. Symptoms may first appear after weeks, months, or even years. Symptoms may result from many types of activities, performed at work or at home, and it is often difficult to attribute a single event. In fact, it is more common to identify the factors which may have contributed to the development of the condition. The terms repetitive strain injuries or cumulative trauma disorders (CTDs) have been commonly used to refer to disorders that have occurred due to work related activities (Putz-Anderson, 1988; Fraser, 1989). Three main risk factors contribute to CTDs: force, repetition, and awkward postures. Any one or combination of these may contribute to the development of CTDs. Therefore, the design of equipment in conjunction with the required tasks should attempt to reduce these risk factors. Examining the layout of the work area to help identify tasks which may contribute to cumulative trauma is necessary. The following list(Putz-Anderson, 1988), describes ergonomic concerns that, overall, should be minimized at the work area:

Jan 1, 1997

By R. P. Vinson, Abdurrahman Cetinbas, Joseph Cervik, M. G. Zabetakis

The effect of water infusion on the flow of methane and on the production of dust was investigated at an active face in the Pittsburgh coalbed. The average total flow of methane at the face decreased by approximately 79 percent, whereas the flow from the ribs increased about 24 percent after infusion. On the day after infusion, dust concentrations appear to have been reduced; however, the presence of large quantities of rock dust obscured the results on the following days.

Jan 1, 1972

By C. E. McElroy

"INTRODUCTION The ventilation of working places in mines by jets of air discharged from fan-pipe lines is an important phase of mine ventilation, whether the primary purpose is to dilute gas or dust concentrations or to provide air-motion cooling effect. Jets of similar nature are very prominent factors in the ventilation of enclosed spaces, such as buildings and ships. The effectiveness of such jets depends on the distribution of the air in the jet streams, a subject on which the little definite information previously available applied to jet discharge into large, open spaces under conditions quite different from those ordinarily associated with fan-pipe discharge in mines.The results of an initial series of experiments on the discharge of air from fan-pipe lines in mine openings have been described. 3/ This report presents the results of a second series of experiments and compares the results of both series with theory and experiment on jet discharge into large, open spaces. The results of this second series confirm and supplement those of the initial series, in which a 10-inch pipe discharged into an 8- by 8-foot develop¬ment end through seven short discharge pieces of different designs. In the present series the same 10-inch line was used, but the discharge was through 10- to 30-foot lengths of 5-inch, 10-inch, and 20-inch-diameter pipes and through a 20-foot length of 29- by 3-inch pipe. Tests were made with the air discharged into a closed drift or development end, as in the previous series (in which case the discharged air returned past the end of the pipe) and into an open drift (in which case the discharged air did not return past the end of the pipe but continued out along the drift). Test conditions corresponded to the discharge of a jet into a channel closed at one end; in one case, the discharge was directed toward the closed end and in the other toward the open end. The former typifies fan-pipe ventilation of development ends and the latter an abrupt increase in the sectional area of an airway. In both the flow had to pass from jet to open air against some resistance.The tests were made in the Mount Weather Testing Adit of the Bureau at Bluemont, Va., on the pipe line installed for ventilating the adit, and extended from late September to mid-November 1940. Preparations were made for directly comparable series of experiments on the injector effect of fan-pipe discharge in an open drift and on free expansion in large, open spaces, but these test programs were .first postponed in favor of other work and finally abandoned until the war is over."

Nov 1, 1943

By M. Zaki El-Sabban

Tables of chemical thermodynamic properties for the ideal gas state from 0° to 1,000° K are reported for eight alkanethiols, three cycloalkanethiols and arylthiols, six thiaalkanes, two dithiaalkanes, three thiacycloalkanes, and three thiophenes. They are based on current physical and thermochemical constants and definitions, reliable vibrational assignments, and the latest insights into molecular structure and energetics.

Jan 1, 1970

By Michael S. Contratto, Dave Marshall, Tom Brodersen

The European Union (EU) completed a new directive 2002/44/EC1 called the Physical Agents Directive (PAD) that establishes action and limit values for hand-arm and whole body vibrations. The directive specifies that: “…workers shall not be exposed above the exposure ‘limit value’.” 1 and “…once the exposure action values … are exceeded, the employer shall establish and implement a programme of technical and/or organisational measures intended to reduce to a minimum exposure to mechanical vibration and the attendant risks…” 1 The PAD limit value is effective for new machines starting July 6, 2007 and for used machines by at least July 6, 2010. These requirements apply to the users of machines, but machine manufacturers will be challenged to provide machines and information to help the users comply with the directive. Caterpillar manufactures machines with the goal of enabling our customers to comply with all regulations dealing with health and safety. Caterpillar designs all of our machines to provide a safe, comfortable and productive work environment. This study was to determine if seat suspensions could provide a reduction in the vibration environment experienced by operators of Caterpillar mid sized (<50,000KG) Track Type Tractors Methods Seat manufacturers were asked to provide seat suspensions that provide improved isolation over and above current seat suspension. Each supplier was provided with ride profiles and was asked to demonstrate the vibration reduction on a shaker table. Two suppliers provided suspensions that were compared with the current seat suspension in a field study. Three full factorial experiments were conducted. The first experiment was to evaluate overall suspension performance for four operations. The second experiment was to determine the benefit of the adjustable vertical damper at three different levels and the third experiment was to determine the effect of the fore/aft and side/side isolators. Six operators were used for the study. Acceleration was measured at the seat base and at the operator seat pad. Both the transfer function and the ISO 2631 RMS ride values were used to determine the seat suspension’s effectiveness of isolating the operator from vibration. A structured questionnaire was used to determine the operators’ subjective assessment of the seat suspensions. Results There was significant operator-to-operator variability in the vertical direction (>35%), however there was little variability in the fore/aft and side/side direction based on seat base

Jan 6, 2006

By Mark Davis

As a follow-on to previous investigations, reduced treatment levels for the optimum fire retardant/preservative system were evaluated. An impregnation of 3.5 lbs/ft3 of Fyreprufe followed by 3.5 mils of Albi 107A plus an Albi 144 top coat provides adequate flammability and flame spread protection. However, there is a significant loss in compressive strength at this retention level, particularly parallel to the grain. A pilot-size pressure impregnation cell was installed for use in treating larger quantities of wood. Based on the optimum fire retardant/preservative treatment system - Fyreprufe/ACC impregnation followed by Albi 107A/144 intumescent paint - a model treatment pro¬cess was developed, capable of handling 3 million board feet per year. Associated annualized costs per thousand board feet (K bd. ft.) for treating 12" x 12" timber were calculated to be: Impregnation: $-63.00/K bd. ft. Coating: $112.00/K bd. ft. A literature search was conducted to identify materials and techniques suitable for a localized stench warning system for heated mine timbers. Based on this review, a number of stench warning concepts were developed. Those based on surface coating were given a preliminary laboratory evaluation.

Jan 1, 1982

By F. S. Crawford

The wide variation in the medical facilities, type of accident reports and provision for the welfare of employees, in addition to the compensation provided by the various State laws,- was -studi-eci, by the.. wri-ter in the Lake .. Superior_ r.egion . .. - -Several cDmpanies f~rnished. the information which follows. Names have been omitted , ~ut the information should be of .intere·st to companies desirous of improving t_his branch of thej..r accident-prevention work. : . . --Because a summary of the metho.ds used would merel:y: result in _ a.n a.ttempt to set _up an ideal, it was concluded that in preparing this paper a statem.ent .of_ tbe individual methods of -each company wou-l d .b-e .Qf .. the most inte-res.t, . and the.y h~ve . been .. li.steq with .no regard to the size of the company . . ··· -In the - appendix are -a -number of report. forms used by .various _operators for reporting accidents to t he company and .to the State. These are self- explanatory. and many a re mentioned in -the body of circu-1-ar-.

Mar 1, 1932

By Michael L. Boninger, Erik J. Wolf, Rory A. Cooper

Although wheelchair users are regularly subjected to whole-body vibrations little research has been conducted to assess these vibrations or attempt to reduce them [2,3,5]. Most of the wheelchair and whole-body vibration research done to this point has been conducted on manual wheelchairs. Van Sickle et al showed that manual wheelchair propulsion over a simulated road course produces vibration loads that exceed the ISO 2631-1 standards for the fatigue-decreased proficiency boundary at the seat of the wheelchair as well as the head of the user [6]. In a study by Boninger et al [1], 66% of wheelchair users reported neck pain since acquiring their wheelchair. One of the key reasons believed to be the cause of pain, was the exposure to whole-body vibration. Kwarciak et al [4] and Wolf et al [7] performed similar studies using two methods of analysis to evaluate vibrations on suspension and non-suspension wheelchairs while descending curbs of varying heights. Both studies revealed no significant difference in the abilities of the wheelchairs to reduce the amounts of vibrations transferred to the wheelchair user. Although the efforts of wheelchair companies to reduce the amounts of whole-body vibration transmitted to wheelchair users through the addition of suspension systems is encouraging, the technology is not yet ideal. Additionally, the research to date has focused on manual wheelchairs exclusively, while little attention has been shown to powered wheelchairs. Methods This study includes the use of two suspension electric powered wheelchairs: The Quickie S-626 and the Invacare 3G Torque SP Storm Series. Each subject tested all of the configurations of the suspension wheelchairs. These included the Invacare with suspension, the Quickie with suspension set to three settings (most stiff, least stiff, and 50% stiffness), and both wheelchairs with solid inserts to act as non-suspension wheelchairs. Sixteen able bodied subjects have been recruited for this study so far. In each of the configurations of the wheelchairs, the subjects traversed an Activities of Daily Living (ADL) course. Vibrations were collected from a tri-axial accelerometer attached to a seat plate beneath the cushion during driving over the activities course. A mixed model ANOVA was used to determine if there were differences between suspensions based on Vibration Dose Value (VDV). Results Statistical analyses of the VDV data revealed significant differences between the six different suspensions over each of the obstacles in the activities of daily living course. Post-hoc analyses revealed that for each of the obstacles, significant differences existed between the Invacare suspension and the Invacare solid insert. For the Quickie power wheelchair the solid insert setting was not significantly different from the most-stiff setting for each of the obstacles

Jan 6, 2006

By A. J. Kraemer

This paper is the second and concluding report of the results of the twenty-fourth semiannual survey made by the Bureau of Mines of motor gasoline marketed in the United states. The first report on this 1931 survey gave the results of the examination of the gasoline samples in accordance with the new Federal specification for United States Government Motor Gasoline. The present paper reports results of the examination of the gasolines for color, doctor test gravity, end point, per cent recovered copper-dish gum, and steam-oven gum. The retail price and the tax at the time each sample was taken are also reported.

Jan 1, 1932