Search Documents

By L. C. IlsLey

"During the last eight years there has been a noticeable increase in the use of permissible equipment in gassy and dusty coal mines. This trend has undoubtedly been toward greater safety in mining, but in spite of this all is not well ""along the front.""In many mines those in charge, either through ignorance or supposed economy, have neglected to install sufficient copper and maintain good bonding on the rails used for return circuits to have a safe working voltage for the permissible equipment which is intended to afford them safety.Low voltage, when properly analyzed, is not economy but frequently is an expensive oversight. Burned-out armatures, controllers, rheostats, and switches are costly in themselves to repair or replace, but the greatest cost in many instances is the loss of production resulting from idle and broken-down equipment.From a safety standpoint, excessive low voltage where permissible equipment is necessary is almost criminal negligence. A burn-out of any kind is liable to cause an arc that may burn its way through a casing wall and bring about a hazardous condition if gas or dust in explosive proportions should be present. Again, all wiring, both interior and exterior to the apparatus, is subject to the extra heating consequent upon low voltage. It should be remembered that if the voltage drops the current must increase a corresponding amount in order that the same work may be accomplished; and as the heating effect is as the square of the current, an enormous overheating of the electrical parts and wiring often takes place. This heating effect is especially detrimental to trailing cables used on portable equipment, because under the most favorable conditions the size of cable selected is only barely sufficient to do its work properly at a safe working temperature; therefore, when the extra current load is added because of poor voltage, overheating is sure to result, with consequent deterioration of the insulation, This effect greatly increases the liability of cable failures in service, and in turn adds to the hazards incident to the use of portable equipment of the permissible type involving the use of trailing cables.Some manufacturers have tried -to protect their equipment from low voltage, especially below a certain point, by -installing low-voltage relays which will trip when the voltage falls to a predetermined value. It is understood that some operators have hesitated or refused to install such low-voltage protection because they were aware that the voltage conditions were so poor that the equipment could not operate under the safe limits set. It is difficult to understand how any progressive company that is willing to go to the ex-pense of installing permissible equipment could be so shortsighted in this phase of common sense, safety, and economy."

Dec 1, 1929

By Stephen C. Tadolini, Thomas M. Barczak, Paul McKelvey

A new generation of hydraulic mine support prestressing devices has been developed. These thin-walled steel shells are machine-welded and can be inflated with water or any liquid to provide prestressing for a wide variety of roof support products ranging from Can supports to props and cable bolts. With an expansion capability of several inches, depending on the geometry and size of the unit, they can also establish roof contact eliminating the need for wooden wedges or crib blocks that are commonly employed with several standing roof support products. Capable of withstanding pressures from 1,000 to 6,000 psi, these cells are able to transfer roof loading into the support structure without rupturing. A recent development has been the addition of an inexpensive yield valve that provides control of the maximum pressure and load development on the support. This paper examines the performance capabilities of these inflatable prestressing units and the impact they have on the performance of various support systems, including an evaluation of the overall stiffness of the support system and the load control during yielding of the prestressing unit. Recommendations are made regarding the design requirements of the prestressing unit to optimize the support performance. A summary of mine applications using this technology is provided with general comments regarding their impact on ground control.

By John B. Gayle

The Bureau of Mines has designed and constructed an experimental coke oven, using a commercial oven as a model where practicable. Because the rate of carbonization is important in determining the quality of the coke produced and may affect the "mount of pressure developed during carbonization, particular attention was given to those elements of the design that govern the heat transfer to the charge. The new oven deviates in design from most existing test ovens in that the charge is full width (17 inches), the heating walls ore constructed of 4-1/2-inch silica brick, and zoned, heat-input arrangements compensate for heat losses at the ends, top, and bottom of the charge. This report describes the oven, which was designed by H. S. Auvil and installed under his direction, at the Southern Experiment Station, Tuscaloosa, Ala., while he was supervising, engineer, Coke Section. It gives the results of a limited number of carbonizing tests. These results indicate that the main objective in designing and building this oven, that off duplicating commerical, slot-oven carbonizing conditions, has been accomplished; if coke-discharge conditions simulate commercial-oven conditions, the cokes from the experimental oven arc very similar to oven coke, in soma tests being fully as close is duplicate tests from a Angle batch of coke.

Jan 1, 1952

By E. L. Garton

[AnalY3e s of Qany crude t) i 1 s prod.uced in Loui sia.na are incl udeo" in re!Jor~ ~ th'l t have b en u~li shed by the BurOllU 0: i?{ine s. The first rc-port,j} givin..; analyseG of 6 Louisiana crude oils, '-vas pUblluhed in 1921'l.s,nd this was 1'0110\ cd a year later by P.ep rt of InvBstign.tions 21a6t~ givi~ 7 addi tional analyses. The G7even :,ost il'!lportant of these analyses were incol"]lorated in Bulle~in 91,.2, is~ued in 1928. In 1934, analyses of 26 cl ... ude oils j)roduced in southern Louisiana ",ere published ? .§! The present report I)renonts analysos of 72 ad(~itional samples of crude oil frorl 4-, fields in 23 "l)ari shefl in Loui f",io.r]

Jan 1, 1939

By T. L. Joseph

The Bureau of Mines gas been studying the blast furnace for a number of years and has published detailed reports on various phases of its investigations. Inquiries frequently received for information of a more general character than that given in the detailed reports have promoted the preparation of an information circular to cover in a general way the important features of the Bureau of Mines blast-furnace investigations. SHAPE AND DIMENSIONS OF FURNACE The modern blast furnace approximate a refractory-lined steel cylinder about 90 feet in height and 25 feet in diameter. It actually consists of a number of cylinders and truncated cones superimposed upon each other. The shape and dimensions of a modern furnace are shown in figure 1. The bottom section, commonly referred to as the hearth or crucible, is a cylindrical section about 12 feet high. Liquid metal and slag collect in this part of the furnace and are withdrawn at regular intervals; iron is removed at a level about 2 feet above the bottom of the furnace and slag at a level about 5 feet higher. Depending upon on the size of tie furnace, 40,000 to 75,000 cubic feet of preheated air per minute is introduced through from 10 to 16 tuyeres equally spaced around the periphery of the hearth.

Jan 1, 1934

By Robert J. Timko

This U.S. Bureau of Mines study examined spontaneous heating episodes in coal mine pillars in an active underground coal mine. The information obtained from these incidents was then analyzed to learn which sampling methods provided the earliest indication of pillar heating. The objective of this study was to discover if the location of future events of pillar spontaneous heating could be inferred from the available information. The spontaneous heating-prone area in this evaluation involved pillars located just inby the mine portals. Several detection methods were used to determine gas levels outside as well as inside the affected pillars. It was hoped that, by incorporating external and internal sampling methods into an organized pro-gram, locations undergoing spontaneous heating could be determined more readily. This study found that by drilling small-diameter boreholes into the pillars, then obtaining gas samples from the affected pillars, the ability to locate early spontaneous heating episodes was improved. However, the ability to accurately predict future spontaneous heating events remains in question.

Jan 1, 2010

By Harold J. Bennett

This study was performed by the Bureau of Mines to evaluate the potential supply of primary copper from domestic resources. A tonnage-price relationship was developed indicating the quantity of copper that could be produced economically from known deposits at various copper prices and at various rates of return on the required capital investment. Costs of production are based on estimated capital and operating costs for mining, concentrating, smelting, and refining the copper. Total known recoverable copper resources are 189 million short tons of which 83 million tons could be economically recovered assuming a price of $0.50 per pound of copper, credit for the recovery of byproducts, and a 12-percent rate of return on capital investment. The quantities of recoverable byproducts associated with the 83 million tons of recoverable copper are molybdenum, 1.8 million tons, gold, 43 million troy ounces, and silver, 740 million troy ounces.

Jan 1, 1973

By Jürgen F. Brune, Alex C. Smith, William D. Monaghan

One of the predominant causes of fires in underground coal mines is flame cutting and welding. These fires can lead to major events such as the explosion that occurred on January 22, 2003 in an airshaft being constructed at the McElroy mine. Six contractors were inside the shaft at the time of the explosion and the explosion fatally injured three and seriously injured three [MSHA 2003]. Understanding the root causes of these fires and explosions will help prevent these types of events from occurring in the future. Fires and explosions require fuel, oxygen and an ignition source (heat). These three items are referred to as a fire triangle. The control of these three items in flame cutting and welding operations is required to prevent fires and or explosions. United States Department of Labor, Mine Safety and Health Administration (MSHA) Reports of Investigation (ROI), MSHA Mine Accident, Injury, and Illness Reports, and the MSHA Mining Industry Accident, Injuries Employment, and Production Data Base were analyzed and interviews and observations with mine workers and welders were conducted to determine the root causes of coal mine fires and explosions caused by flame cutting and welding operations. This paper will discuss the root causes and potential means to reduce the number of fires and resulting fatalities and injuries caused by or due to flame cutting and welding.

By Elaine T. Cullen, Thomas W. Camm

The mentor/learner model is a time-honored approach to teaching, including within the mining industry. Miners know when they see excellence and have a deep respect for experts in their field. By using expert miners as mentors to other, less-experienced miners, training programs can be developed that will have a legitimacy and credibility that resonates with those being trained. Building upon concepts in current theories of adult education, this paper highlights the unique advantages of using mentoring as a teaching method that can make the educational experience both interesting and effective. Current NIOSH safety training materials use these concepts to deliver effective adult learning experiences for workers in the mining industry.

Jan 1, 2002

By N. I. Jayaraman

High-pressure shrouded sprays were first tested on a bench to determine air-moving capability and dust collection efficiency. The bench-scale tests indicated that at 500 psi and above, the dust collection efficiency, when sampled downstream of a water eliminator, was about 99 pet for two types of nozzles. However, for the same water flow, the induced airflow was about three times greater in one type than in another. Since the only difference in the nozzles was the spray angle, this factor was important in air movement through a shrouded spray. Full-scale model mine tests were then conducted to determine the reduction in dust concentration behind the line curtain and at the operator position produced by high-pressure sprays in a shroud. The shroud was mounted on top of the boom of a model continuous miner, and high-pressure (greater than 500 psi) sprays were installed inside the shroud. The inlet of dusty air to the shroud was open toward the face and the outlet toward the exhaust line curtain. The high-pressure sprays were compared with conventional sprays mounted at the head of the continuous miner and directing water toward the face. The difference at the operator position (opposite side of brattice) was significant in that, under certain conditions, with conventional sprays an increase in respirable dust concentration of 471 pet was noticed compared with dry operation due to rollback from face. High-pressure shrouded sprays, on the other hand, decreased the dust concentrations at the operator position (opposite side of brattice) by 28.2 pct.

Jan 1, 1981

By Clyde L. Brown

The ignition source of fires and explosions in coal mines is sometimes difficult to explain because resulting widespread destruction often erases valuable evidence that might reveal the cause. However, through years of experience, investigators have been able to piece together enough evidence to establish the reasons and, thereby, have been equipped to recommend corrective or preventative measures. The pattern of hazards is not constant. It changes with the development of new practices and new equipment. Important among the new hazards to coal mining are those introduced by electricity. In addition to the dangers of electric shock, fires and explosions from heat and arcs, and premature blasts, certain others have developed as a result of stray electric currents from direct-current traction systems. The conventional direct-current power-distribution system in coal mines is conducive to electrolysis damage to mine tracks, metallic pipelines, grounded power conductors, and structures in a position to become conductors of stray currents. The voltage drop resulting from power demand on intentionally grounded power conductors and accidental grounds on insulated conductors are common sources of stray currents in coal mines. Uncontrolled electric cur-rents flowing through the earth and metallic structures can be a menace, and these contribute to the estimated $6,000,000,000 annual loss caused by corrosion. The purpose of this publication is to discuss some of the electrolysis hazards in the coal-mining industry and to outline corrective measures to alleviate them.

Jan 1, 1962

By Walter J. Huff

"INTRODUCTION The technical studies conducted by the Explosives Division of the Bureau of Mines have been summarized in a series of publications issued annually for the past 10 years. 3/ The following account covers studies undertaken from July 1, 1944 to June 30, 1945. The work is set forth under a number of main headings to correspond to the organizational structure of the division, the various activities being under the immediate direction of unit chiefs, who report to the author. Specific credit it due to the unit leader and his assistants.Determination of Ignition TemperaturesThe ignition temperature of mixtures of isobutane and air were determined by the static method using a 131-cc. quartz bull. 5/ The results obtained follow: Prevention of Benzene-Air Explosions by Addition of Nitrogen and Carbon Dioxide The elimination or mitigation of the explosion hazards of combustible gases is a part of the work undertaken by the Bureau of Mines in promoting safety. Explosions can be prevented by the maintenance of concentrations that lie outside the inflammable limits. A procedure has been developed whereby the inflammable limits of many complex gaseous mixtures may be calculated in a rather simple manner without requiring toilsome laboratory experiments. This procedure has been outlined in a number of previous publications. 6./ During the fiscal year under review, essential data required for the calculations of complex combustible gas mixtures containing varying percentages of benzene were obtained. Benzene vapor is a normal constituent of many manufactured gases and is widely used in the solvent industry and in the manufacture of high explosives."

Oct 1, 1946

By G. F. Friel, J. C. Edwards

A series of seven underground-coal-mine fire experiments was conducted in the Safety Re-search Coal Mine at the National Institute for Occupational Safety and Health, Pittsburgh Research Laboratory. Coal and styrene-butadiene-rubber conveyor belting were burned upwind of two sensor stations, 18 m and 148 m from the fire source. Exhaust from a diesel locomotive flowed over the fire sources in six of the tests. Metal-oxide-semiconductor (MOS), CO, and optical-path-smoke sensors were positioned at both stations and found to be an optimum set of sensors for the fire discriminations. A representative set of 7,679 samples of CO data and data from the smoke and diesel-exhaust MOS sensors were used as inputs to train a neural network (NN). By testing 42,538 data samples from the seven experiments, all fires were detected by the NN within 9.67 min from the onset of significant changes in the MOS voltages without any false alarms.

By Eugene T. Sheridan

The process of converting coal into coke is known as carbonization. Essentially, carbonization is destructive distillation in which the volatile matter of coal is released when coal is he ted above its decomposition temperature and passes through a plastic stage before solidifying and forming coke. The mechanics of coke formation are complex, and the specific properties of certain coals that tallow them to "cake" or form coke are still unknown. Coke is a hard, cellular, carbonaceous mass, formed by heating coal in the absence of air. It is porous, irregular in size and shape, and is similar in appearance to wood charcoal. Coke, however, is denser, more porous, and more abrasive than charcoal.

Jan 1, 1965

By Eugene T. Sheridan

The process of converting coal into coke is known as carbonization. Essentially, carbonization is destructive distillation in which the volatile matter of coal is released when coal is heated above its decomposition temperature and passes through a plastic stage before solidifying and forming coke. The mechanics of coke formation are complex, and the specific properties of certain coals that allow them to "cake" or form coke are still unknown. Coke is a hard, cellular, carbonaceous mass, formed by heating coal in the absence of air. It is porous, irregular in size and shape, and is similar in appearance to wood charcoal. Coke, however, is denser, more porous, and more abrasive than charcoal.

Jan 1, 1965

By C. W. Morris

The continuous miner training system provides classroom materials training aids, and a continuous miner simulator to provide a short, intensive instruction and skills development program for training or retraining continuous miner operators. This project included refinement of training objectives, revision of training aids, improvements to the simulator, and evaluation of the entire system. This report describes the revised classroom materials and the validation of the training system.

Jan 1, 1982

By Donald E. Buck

In 1988, Albania's centrally planned economy continued to decline. The country's officially published yearend economic report did not contain concrete results such as the growth of national income or industrial output. 2 The shortfall for central budget earnings for 1988 amounted to 9% below the planned target. Losses in industry were attributed to poor management and organization, as well as to low technical standards and excessive consumption of fuels and raw materials. The construction, energy, and mining sectors of industry did not meet their annual production plans. As in 1987, within these sectors, the chromite and petroleum extracting and processing industries continued to lag in output. Both chromite and petroleum remained Albania's chief sources of foreign exchange; the production downturn of these commodities continued to negatively affect the country's foreign trade position, especially in view of constitutional prohibitions against using foreign credit to finance trade. The chief events in the minerals industry in 1988 included the construction startup of the first of four planned new concentrators at the Bulquize chromite mine, as well as the construction startup of new ferrochromium capacities at Elbasan. Also, the copper mining industry reported the completion of facility expansion at the Perlat mine in the Mid-rite district. Albania began new facility construction at the Dinamo heavy-equipment enterprise at Tirana to maximize self-sufficiency in mining equipment production. Upon completion, the new factory would double the out-put of mining equipment at the enterprise and would introduce new designs for electric trucks and pneumatic drills for the mining industry. The new facility would also increase the production of new machinery and equipment for the country's beneficiation plants.

Jan 1, 1990

By P. M. Ambrose, C. Travis Anderson, Cresap Moss, R. S. Dean

"MANGANESE METALMethods of PreparationMethods of preparing the manganese metal that has been used in chemical and metallurgical investigations have passed through a cycle. Most of the investigations made before the turn of the century used Moissan's pyrophoric manganese. 5/ This material was made by electrolysis into a mercury cathode and distillation in vacuo. It was essentially a pure material, and investigations in which it was employed (with proper precautions against oxida¬tion) led to accurate results concerning the intrinsic behavior of metallic manganese.An early investigation of the properties of ""Manganese-by-Mercury"" was made by M. Guntz. 6/ He prepared manganese by electrolysis of a concentrated MnCl2 solution with a mercury cathode. The manganese amalgam was pressed through chamois and distilled in vacuo (2 to 3 cm. of mercury) at 200°0., slowly rising to 250°0. Guntz recognized especially the decreased reactivity of manganese with increased temperature of mercury distillation. The most careful and com¬prehensive study of manganese made by this method is that of Kuh 7/ whose work unfortunately was never published in an accessible journal.Royce and Kahlenberg 8/ studied the electrode potential of manganese made by this method."

Nov 1, 1939

By D. E. Welcome, T. W. McDowell, R. G. Dong, S. F. Wiker

Workers using vibrating hand tools have the potential for developing health problems associated with repeated forceful actions and exposures to hand-transmitted vibration. Hand-arm vibration syndrome (HAVS) and other hand-arm system disorders have been associated with such exposures.1-2 To better assess health risks, comprehensive evaluations of these exposures must include quantitative assessments of hand-tool coupling forces; unfortunately, no standardized method for quantifying hand forces exists. Handle instrumentation may be ill-suited for some field environments. Psychophysical force-recall techniques may provide alternatives to handle instrumentation. A thorough understanding of the effects of vibration and other factors on force-recall accuracy and reliability is important before such methods are applied in risk assessments. Methods In this study, the effects of vibration and other factors on the accuracy of psychophysical force-recall were explored in two experiments. Twelve male subjects participated in the first experiment. The second experiment employed 20 participants (10 female, 10 male). In each experiment, participants applied specific grip and push forces to an instrumented handle mounted on a shaker system. Participants were exposed to sinusoidal vibration at frequencies that ranged from 0 Hz to 250 Hz. Three levels of applied force (low: grip = 15 N/push = 25 N, medium: grip = 30 N/push = 50 N, and high: grip = 45 N/push = 75 N ) and two levels of vibration magnitude (low: ANSI 4-8-hr limit and high: ANSI <0.5-hr limit)3 were examined. During the vibration exposure period, participants were provided with visual feedback while they attempted to “memorize” the applied grip and push forces. At the conclusion of the vibration exposure/force memorization period and a controlled rest period, the participants tried to duplicate the grip and push forces on a non-vibrating handle without the aid of visual feedback. The effects of different vibration frequencies, vibration magnitudes, and grip and push force levels were tested in a random order from trial to trial. Results Participants tended to overestimate grip and push forces. Depending on exposure conditions, error means ranged from 2 N to 10 N. The ANOVA revealed that force-recall errors for exposures between 31.5 Hz and 63 Hz were significantly higher than those at other vibration frequencies (p < 0.05). The frequency effect is depicted in Figure 1. Error means were greater when participants were exposed to the higher vibration magnitude (mean = 9.1 N, 95% CI = 8.2-10.1 N) when compared with the lower vibration magnitude (mean = 4.9 N, 95% CI = 3.9-5.8 N) (p < 0.05). The effect of vibration magnitude is shown in Figure 2. The average error for

Jan 6, 2006

By Jerry E. Olson

In 1986, at the request of the U.S. Bureau of Land Management, the U.S. Bureau of Mines studied part of the 20,071-acre South Fork Wilderness Study Area (OR-005-033) and part of the 8,791-acre Sand Hollow Wilderness Study Area (OR-005-034) in order to evaluate their identified mineral resources. The study areas are located in Crook County, OR, about 58 air miles east from Bend. The areas studied are underlain by Tertiary- and Quaternary-age volcanic and tuffaceous sedimentary rocks. No mineral resources were identified in or adjacent to the study area. Except for common opal and agate occurrences along the northern boundary of the study areas, no mines, prospects, or mineralized zones occur within the study areas. Bentonite is periodically mined less than 1 mi southwest of the Sand Hollow study area boundary. Neither of the study areas has geothermal leases, but both areas are under lease for oil and gas.

Jan 1, 1987