Search Documents

By S. Stephen Uslan

The purpose of the study was to demonstrate the effect of positive reinforcement, specifically, social reinforcement (SR), on the frequency of eye, hand, and back injuries at four experimental salt mines. Injury data was collected from January, 1976, for the prePOMOST period and from the onset of training to September, 1978, for the post-POMOST period. All data was collected on a month-by-month basis. For the training period approximately 100 managers and supervisors from five plants were trained in the use of positive reinforcement for occurrences of "safe behavior." Each supervisor was also provided manuals and other supportive materials. Additionally, following training, all supervisors were provided some coaching experience to keep the knowledge and capabilities gained during training from being extinguished. The analysis showed significant injury reductions in two sites and no injury reductions in the other two. When the injury data was corrected for the additional man hours expended in the postPOMOST period, a third site showed reduction in injuries. Similar findings were shown when the experimental sites were compared to other sites in the industry. The results were interpreted to support the hypothesis that the application of social reinforcement is related to a reduction in injuries.

Jan 1, 1978

By M. J. Ferrante

The Bureau of Mines investigated the applicability of the freeze-drying technique for preparing dispersion-strengthened tungsten powders suitable for conversion by powder metallurgy into materials which might have improved high-temperature strength. Extruded rods from compacts of tungsten-5 vol pct thoria had at 1,650° C a tensile strength of 30,300 psi and a 10-hour stress-rupture strength of 12,700 psi, These are slightly below those measured for swaged rods of commercial tungsten-3.7 vol pct thoria. Only those tungsten-thoria dispersions containing a stoichiometric deficiency of oxygen yielded a significant strengthening effect. A low-melting eutectic formed in extruded tungsten dispersions containing either zirconia or yttria, which caused a lowering of the tensile strengths. These tensile strengths were only slightly higher than strengths of elemental tungsten made from commercial powder having a particle size of 2.4 microns (Fisher subsieve). Sheet made from this commercial tungsten had a slightly higher tensile strength than tungsten made by freeze drying, but the freeze-dried tungsten sheet had a lower recrystallization temperature, a lower ductile-to-brittle transition temperature, and a higher purity.

Jan 1, 1971

By A. B. Pederson, G. E. Bartlett

As a part of our study of how coal mine dusts injure the lung we have studied the effects of dusts and dust-exposed pulmonary alveolar macrophages (PAMs) on the growth of lung fibroblasts (LF). Fibroblasts were cultured near confluence in low-serum medium, either alone or in the presence of dusts, dusts plus PAMs, dust leachates or superriatants of dust-exposed PAM cultures. We report here provisional conclusions, based on initial observations. Rat LF were relatively unresponsive to direct effects of dusts, showing weak stimulation in only a few cultures, and there was no evidence that dust-exposed rat PAMs had released any growth-regulatory products. In contrast, guinea pig cells were more responsive to the dusts. The pattern of responses was quite complex. Three of the dusts stimulated LF directly (with no mediation by PAMs). Two dusts were essentially inert when added directly to fibroblast cultures, either with or without PAMs, but their leachates were active: 867 leachate was inhibitory and RF leachate was stimulatory. Dust 1361, either directly in the cultures or as an aqueous leachate, was stimulatory, and it activated cocultured PAMs to stimulate LF growth; however, supernatant products of 1361-stimulated PAMs were inhibitory. Direct exposure to 1192 stimulated LF, but its leachate was inert; cocultured PAMs exposed to 1192 had weak stimulatory effects, but supernatants of 1192-exposed PAMs were mildly inhibitory. MP3-3 had effects similar to 1192, except that the cocultured, dust-exposed PAMs had no effect on growth. We conclude 1) that guinea pig lung cells are more responsive to dusts than are rat lung cells, 2) that dusts can influence growth of LF by four kinds of interaction (by direct dust-cell interaction, by release of soluble dust components into the culture medium, by activating P AMs to exert direct cell-cell interactions, and by activating P AMs to release growth regulatory products into the culture medium), 3) that each kind of interaction may be neutral, inhibitory or stimulatory, depending on the dust tested, 4) that four of the dusts tested were neutral, inhibitory or stimulatory, depending on the assay (the fifth <lust was either neutral or stimulatory), and 5) that the effects of soluble mediators (leachates or products of activated PAMs) frequently did not correspond with the direct dust-cell or PAM-fibroblast effects. These results suggest that the nature of the dust-lung interaction at the level of cells and molecules is exceedingly complex. These observations need to be confirmed and extended to determine what characteristics of the dusts determine the nature of the cellular responses, and to determine which patterns of responses are detrimental and which are beneficial in the overall health of the dust-exposed lung.

Mar 1, 1989

By Ned Baker

Details are given of a Hydride Fuel System to provide 5 kg of HZ to fuel a Caterpillar 3304 engine previously modified to operate on hydrogen fuel and intended to power an underground mining vehicle. The Fuel System was installed onto the engine and the Engine/Fuel System tested under cold start conditions and a full range of engine loads and speeds. Refueling tests were also performed. The fuel system tested will support full engine power and allow delivery of at least 3/4-power on a continuous basis, from cold start conditions.

Jan 1, 1983

By C. A. Rhoades

The spillage that accumulates under conveyor belt lines presents a possible fire and explosion hazard fomiinqjetsoruiel, especially to those who must clean up the spillage. The U.S. Bureau of Mines conducted research to reduce this hazard by identifying and investigating the parameters affecting the efficiency of conveyor belt cleaning. The amount of material carried back under the conveyor and the wear rates of metal cleaning blades decreased with increasing blade-to-belt pressure to a limiting value, after which the carryback and wear rates remained essentially constant. The optimum blade-to-belt pressure was found to be 11 to 14 psi for the research conveyor system. Greater pressures increased the blade-belt friction without improving either cleaning or blade life. The modes of blade wear were three-body abrasion and slurry erosion caused by the sand-lime test mixture. Wear rates were reduced by increasing the metal hardness, opti-mizing the pressure, and removing conveyor belt imperfections. Corrosion was not observed to affect the wear of various steels in tests of less than 34 h. The results of this study should allow mine operators to run their conveyors under conditions that will maximize cleaning and minimize equipment wear.

Jan 1, 1989

By John P. Hager

A special inlet system has been developed for a TOF mass spectrometer that allows the equilibrated high-temperature vapors from an atmospheric-pressure flow reactor to be leaked into the ion source of the mass spectrometer without undergoing any compositional changes. Using this flow reactor - mass spectrometer system and a modified transpiration system (one that allows for the carrier stream to be equilibrated with two different condensed samples) a series of fundamental vapor transport studies were undertaken. The results of these studies are summarized as follows: 1. The vapor species in equilibrium with condensed copper (I) chloride were determined to be Cu3C13, Cu4C14, and Cu5C15. The gas mixture is fifty percent tetramer near the melting point (703°K), with the percentage of tetramer decreasing with increasing temperature. The following thermodynamic results were obtained.

Jan 1, 1977

By K. E. Robinson

This study is the extension of an investigation of reclamation of floodplain areas in the Coeur d&apos;Alene Mining District, Idaho, that are unuseable in their natural condition, by construction of landfills with mill tailings. The study develops a valley-wide tailings disposal plan to utilize 20 potential landfill sites on floodplain areas and presents measures for reclaiming the sites for subsequent productive use. Field and laboratory testing on a test section and two abandoned impoundments support the use of hydraulically deposited tailings for landfill construction. Hydrological testing has shown that controlled discharge from tailings impoundments results in contaminant levels in the discharge below regulated standards. Additional testing indicated that compacted soil liners and pond management provide adequate contaminant abatement where acid-generating tailings are encountered. Mechanical compaction, including surcharge loading, upgrades foundation support capacity so that construction on the surface of tailings deposits is feasible. On completion of the testing program, the test sections were abandoned and rehabilitated. Details concerning potential landfill sites have been refined. At recent production rates, the 20 sites would result in 680 acres of reclaimed land, while providing a minimum of 40 years of tailings storage capacity. A general design has been developed for the retention dikes. Aspects of embankment stability, including liquefaction are discussed, and are shown to provide an adequate factor of safety under the anticipated range of operating conditions.

Jan 1, 1983

By E. O. Wagner, A. W. Koth, V. F. Parry, J. B. Goodman, D. C. Gernies

"INTRODUCTION A commercial-scale pilot plant for gasification of lignite was completed by the Bureau of Mines at Grand Forks, N. Dak., early in 1945 as an extension of work on, gasification of low-rank coals initiated in a smaller pilot plant at Golden, Colo., during 1943. The development work on this plant was part of a program to make reducing gases from lignite for beneficiation of low-grade iron ores. The background of this project has been described in a previous report. 6/ The present report describes the major features of the large pilot plant, a record of experimental operating data during five runs totaling about 1,800 hours, .and results of experimental work on the small pilot plant at Golden during 1945.This project has created considerable interest because heretofore there has been little success in several attempts to gasify American lignites.Furthermore, the methed employed is a departure from conventional processes. Natural lignite is fed continuously into an externally heated annular retort and is converted into water gas by heat conducted through alloy metal walls. Because of the high thermal conductivity of metal, the rate of gasification is several times greater than can be obtained when employing refractory walls. The process has been developed to a part that leaves one major question unanswered. - ""How long will the alloy last under practical operating conditions?"" - and this question has aroussed the interest of the Coal Division of the Bureau of Mines in this new development.Owing to the high reactivity of the lower-rank fuels, the water-gas reactions proceed rapidly at medium temperatures of 1,650°F. to 1,800°F. These temperatures can be attained in a reaction zone heated by external means when the temperature of the retort does not exceed 1,900°F. while transferring from 6,000 to 7,000 B.t.u. per hour per square foot. Such rates are several times greater than can be attained through refractory walls as employed in the Didier-Bubaig 7/ and the Ahrens processes. 7/ Therefore, the investment cost of the gas generator per unit of capacity will be considerably lower for the higher-capacity process. However, the maintenance cost of metal vessels will be higher than that of refractory retorts, and this emphasizes the importance of large-scale operation to determine the life of an alloy retort under practical operating. conditions."

Sep 1, 1947

By G. S. Scott, W. J. Huff, G. W. Jones, R. E. Kennedy

"INTRODUCTION This report gives preliminary results of field and laboratory investigations made at the request of the War Production Board relative to causes that have occurred during the last 8 months in acetylene-generat72,r plants in shipyards on the Pacific coast.Six acetylene-generator explosions have occurred in four shipyards. These explosions killed five operators, injured six others, and extensive damage to the plants involved and curtailmnent of vital defense Although the occurrence of acetyiene-generator explosions in other section of the United States is not known, it appears, at least, that if such have occurred, they have caused only minor damage and no loss of lives.The use of acetylene in shipyards on the west coast has expanded tremendously during the past 2 years. These shipbuilding, companies erected aletylene-generatcr equipment, which was soon found to be entirely inadequate to meet the needs of their expanding acetylene requirements for welding, cutting, shrinking, and other purposes, and instances found it necessary to operate their equipment at rates greater than deemed consistent with safe operating practice."

May 1, 1944

By A. C. Richardson

The mine of the Porter Coal Co. is located at the town of Porter in the northwestern part of Jefferson, County, Ala., about 20 miles west of Birmingham. The operations in this mine are confined to the middle and bottom benches of the Mary Lee bed. The coal from the Porter mine is handpicked and washed before being placed on the market. The handpicked lump coal and the washed egg and nut, coal are sold chiefly as domestic and steam-raising fuel. The coal finer than 1 inch is washed in 2-compartment jigs and utilized in the manufacture of metallurgical coke. The coal company has found that, when coal ranging in size from 1 to 0 inch is washed in jigs, a considerable amount of high-ash material finer than 3/16 inch remains in the washed coal. This paper gives the results of an investigation which was conducted for the purpose of determining the washing characteristics of the through 316-inch raw coal and the extent to which the ash might be reduced by means of coal-washing tables. This investigation has been made in connection with an. extensive study of the coal-washing problems now being conducted by the United States Bureau of Mines and the University of Alabama, with the cooperation of the coal-mining companies of the State.

Jan 1, 1933

By S. R. Borrowman

This investigation by the Bureau of Mines was undertaken to develop information on the extractive metallurgy of thorite ores because potential ore bodies of this mineral have been found recently in Colorado, Idaho, and Montana. Basic information on thorite ore treatment that would be useful in appraising the potential of these and other domestic thorium resources was developed. The work was done mainly on thorite ore containing 3.87 percent ThO2 from the Powderhorn district, Colo., and on a composite sample containing 0.52 percent ThO2 from the Wet Mountains district, Colo. Limited tests of d corroborative nature subsequently were made on a sample containing 2.30 percent ThO2 from the Lemhi Pass area on the Idaho-Montana border.

Jan 1, 1962

By L. F. Heising

This report is a general summary of pertinent data on the manufacture and use of synthetic ammonia products. It provides a condensed summary of the potentialities of a synthetic ammonia industry in North Dakota for Federal, State, and private organizations that may be interested in helping to develop an integrates synthetic ammonia and fertilizer industry. The report contains discussions of: (1) Materials used in the manufacture of nitrogenous fertilizers, nitric acid, and urea; (2) National production, imports, exports, and consumption; (3) the ammonia industry, location, capacity of plants; (4) processes used in manufacturing synthetic ammonia, nitric acid, and urea; (5) other potential industries; and (6) analyses of manufaturing and plant cosh;. Additional information on industrial compounds from ammonia and plant nutrients removed by crops is given in Appendixes 1 and 2. Synthetic ammonia is one of the primary ingredients in fertilizers. Resources required in synthetic ammonia manufacture are available in North Dakota. Hydrogen is available from the petroleum and natural gas resources, particularly in the Williston Basin, and from the large lignite resources in the State. Hydrogen can be produced from lignite by a gasification process developed by the Bureau of Mines at Grand Forks, N. Dak.

Jan 1, 1954

By E. K. Stanek

This research study was performed on a case study basis and can be divided into two parallel thrusts: electrical and thermal energy conservation. Energy consumed annually in mining and refining operations represents about 6% of the 80 quadrillion Btu&apos;s consumed nationally. In the electrical portion of the study, five areas were addressed: optimal dispatching of on-site generation, high-efficiency motors, conductor selection, power factor correction, and high efficacy lighting. In the case study mine which has a multiple unit on-site generation system, optimally dispatching units can save significant energy. The other four methods are difficult to justify on a retrofit basis due to capital costs. In the thermal portion of the study, a thermodynamic analysis was performed on the reverberatory smelting process possible areas of energy conservation were identified as radiation and convection heat losses from the furnace arch and the dumping of high energy content smelting slag. It has been shown that materials currently available can provide the means of reducing heat loss from the reverberatory furnace. It has also been shown that a significant amount of energy may be recovered from the slag. However, these are both subject to further study and validation.

Jan 1, 1982

By J. D. Noll

Elemental carbon (EC) is used as a surrogate for regulating the exposure to diesel particulate matter (DPM) of underground metal/non-metal miners. EC was chosen as a surrogate because EC is selective to DPM and is a major component of DPM. Using EC as a surrogate also gives one the advantages of no sampling artifacts and being able to sample at all locations in the mine. Currently, EC represents DPM well in underground mines. Some control technologies have been shown to possibly alter the relationship between DPM and EC and characteristics of DPM. Therefore, future work will investigate the relationship between DPM and EC as new control technologies are implemented.

Jan 1, 2002

By W. W. Agey

The Bureau of Mines examined and tested the rhodonite deposits of the Silverton lead-zinc district, San Juan County, Colo., as a possible source of domestic manganese. Exploration and development work by several mining companies and preliminary reconnaissance of the area by Bureau of Mines engineers indicated the presence of extensive manganese resources in the form of rhodonite. This report summarizes the results of laboratory beneficiation tests made on samples of different type and grade material obtained from surface and underground exposures of seven veins in the district. Surface and underground examinations revealed the presence of several prominent veins that could be traced up to 2 miles for a single vein along the surface. The principal veins average about 50 feet in width and apparently carry rhodonite to considerable depth. Underground samples were taken from the Sunnyside, Silver Queen, Washington, Independence, and Scotia veins. Samples also were taken from surface exposures of the Sunnyside Extension and Hidden Treasure veins.

Jan 1, 1962

By W. M. Deaton

[The formation of gas hydrates in natural-gas pipe lines depends on temperature and pressure conditions in the lines as well as on the presence of condensed water. The operating pressure in a pipe line may be determined easily and usually is available from the records of operation, but the temperature seldom is known. In cooperation with the American Gas Association, the Bureau of Mines, in its investigation of gas hydrates, conducted a pipe-line-temperature survey and studied underground temperatures at depths at which pipe lines ordinarily are buried and the relationship of these temperatures to prevailing atmospheric conditions. A similar but more limited study of this type was, conducted by engineers of the Bureau of Mines a number of years ago.4/A summary of the earlier findings was included in a general report by the Bureau on the flow of natural gas through high-pressure transmission lines.5/ In the present study, data on temperature variations were obtained at several places widely separated geographically. This information should assist pipe-line engineers in designing and operating natural-gas pipe lines. In the pipe-line-temperature survey here resorted, a study was made along a 22-inch natural-gas pipe line: originating near Amarillo, Tex., and extending northwestward through New Mexico into Colorado (fig. 1). Some data also were collected along a 16-inch line extending southward from Amarillo. In the study of underground temperatures and their variation with atmospheric temperature, recording; equipment was installed at the]

Jan 1, 1941

By M. J. Sapko

A moderately scaled apparatus was developed by the Bureau of Mines to determine the fire resistance characteristics of mine conveyor belts and similar type materials. The design of the apparatus was based upon data obtained in full-scale fire tests and features a radiant panel to preheat the belt and a methane-oxygen ribbon burner to ignite the sample under ventilating condi¬tions in a rectangular duct. The test method overcomes the limitations of existing laboratory-scale methods and provides a measure of both ignitability and flammability in quantitative terms. Flame propagation depended upon such variables as air velocity, ignitor heat flux, and belt width and height in the test chamber. Data are presented for nine belt materials and fire resistance ratings are proposed in terms of the flame spread rate, heat release rate, and the critical ignitor heat flux. The ratings discriminate between the fire hazard posed by different fire-resistant belts and tend to be in reasonable agreement with those obtained in full-scale fire tests.

Jan 1, 1981

By James J. Snodgrass

The Bureau of Mines has investigated vibration levels produced by blasting at four underground sites to establish how such factors as type of explosive, delay blasting, charge weight, and geology affect amplitudes of ground motion. A summary of the work is presented and the results of further analysis of the data are discussed. Square root scaling was found applicable to two of the underground sites and could be applied with minor error to all the sites. Comparison of empirical propagation equations in the different rock types indicates that although the site effect is apparent, the combined data may be used as a basis for engineering estimates of vibration amplitudes from subsurface blasting in many different rock types. Recommendations for predicting and minimizing vibration amplitudes from underground blasts are given.

Jan 1, 1974

By J. E. Conley

Available statistics show that the demands of the American chemical industry for sodium sulphate have been increasing slightly in recent years. The supply from domestic sources, particularly In the form of byproduct salt cake from the acid manufacturers, has been tending to decrease due to the growing manufacture of synthetic acid. Both hydrochloric and nitric acids are being synthesized from their elements. The natural result has been that a smaller amount of salt cake is available. Simultaneously, the expansion of the Kraft paper industry, especially in the South, has brought about greater demand for sodium sulphate in that section. This dean is being met by domestic byproduct salt cake, by imported German sodium sulphate made from potash waste liquors, and by favorable situated domestic deposits of Glauber salts and tile anhydrous salt, thenardite. No shortage of natural sodium sulphate exists in the United States, but usually such deposits occur in semiarid regions far removed from transportation facilities and from markets. Moreover, the major portion of the natural deposits is Glauber salt or mirabilite (Na2SO4 ? 10H20), which must be dried or dehydrated in order to meet consumer requirements. The water of hydration represents, roughly, 55 percent of tae total weight of the crude salts and therefore has a very important influence on transportation costs. In marry instances the cost of getting, even the dehydrated product to market is the deciding economic factor. Therefore, the recovery oil production of anhydrous sodium sulphate from plant-.waste liquors or from natural brines of suitable composition might be economically feasible. The U.S. Bureau of Mines, at its nonmetallic Minerals Experiment Station, New Brunswick, N. J., has, for a number of rears, been investigating the commercial possibilities of treating the complex saline mineral polyhalite (K2SO4?NgSO4?2CaSO4?2H20) for the recovery of potash and magnesia. Certain proposed processes (1, 2, 3, 4)4/ yield waste liquors that contain the bulk of the magnesium and sulphate originally combined as magnesium sulphate in the polyhalite molecule. Sodium chloride In limited concentrations is also present, as extensive beds of salt occur in strata overlying the polyhalite deposits. A typical waste liquor would contain:

Jan 1, 1936

By Michael J. Pazuchanics

This report documents the current status of the U.S. Bureau of Mines ongoing investigation of the use of adaptive signal discrimination (ASD) systems to distinguish between cutting coal and cutting rock. Cutting-tool forces and vibrations were measured in the laboratory using both conical bits and roller cutters in a linear-cutting apparatus for several material samples and two cutting directions. A number of ASD systems consisting of one or more signal classifiers were trained and tested to study how data window size, type of signal feature, and combining (polling) of classifier results influence system performance. The results show that ASD system recognition rates can be improved by increasing data window size, removing air-cutting portions from the signal data, overlapping data windows, and combining (fusing) information at various levels of ASD system operation.

Jan 1, 2010