Search Documents

By Lee Wehner, Daryl Kin, John Bolger

The Maumee Quarry, located in the city of Maumee, Ohio, has large in-situ cavities, ranging in size from 3 ft (.91 m) in diameter to over 15 ft (4.5 m). The drill/blast team challenge is to drill, load and shoot the geologically disturbed rock in a safe, cost efficient manner, while in close proximity to a commercial area. A continuous improvement process, managed by a Blast Optimization Team (BOT), was implemented to quantify the innovative explosive loading techniques that have been implemented. Borehole camera monitoring, modified loading practices, the need for accurate drill hole logging and open communications between the drill and blast crew proves critical to the success of the operation. Safe Standard Operating Procedures (SSOPs) have been developed and are strictly enforced for the drill/blast cycle. All blasts are monitored with seismographs and recorded on video to provide detailed information as part of the Blast Management Plan. Despite the geological challenges, the measurement of rock fragmentation index versus loader dig rates has provided near optimal crusher throughput.

Jan 1, 2007

By Andrew Ritter, Victor I. Montenyohl, Stephen R. Winzer

Thirty-seven open pit production blasting operations have been monitored using high-speed cameras running between 500 and 7000 frames per second. Analysis of the resulting films reveals irregularities in timing including sequencing errors and crowding (holes firing less than 8 ms apart), confirming results of laboratory testing of ms delay blasting caps (Winzer, 1978). Where blasting parameters are otherwise constant and within recommended guidelines (stemming, spacing, burden, etc.), timing problems dominate the overall performance of the blasting operation. Model tests in layered Homalite 100, designed to simulate joint or bedding planes in rock, indicate the importance of the stress waves generated by the explosive in developing the crack network which is ultimately responsible for the fragmentation seen in the resulting muckpile. These mechanisms are strongly supported by high-speed film studies at Pinesburg, Maryland. Experiments in controlling relief in deep shots (where depth approaches the lateral extent of the bench blasted) using borehole geometry and hybrid initiation systems (electronic timer and pyrotechnic delays) were carried out. The results suggest that the 1 me/ft. of burden guideline developed by Bergmann et aI., 1974 is too short, and that much longer times are necessary to optimize fragmentation and muck digability. Longer times are found to reduce noise, vibration, and flyrock.

Jan 1, 1979

By R Holmberg, C Sjoberg, B Larsson

This paper describes the excavation of an underground naphta storage facility at Stenungsund in Sweden. The main purpose with this paper is to give an overall view of how the excavation was carried out and in what type of bedrock the storage was built. Emphasis has been done to highlight the importance of using cautious blasting to avoid blast damage in the remaining rock. Attempts has also been done in order to evaluate what the degree of Swedish cautious blasting has meant for the rock support costs during the construction period.

Jan 1, 1984

By Chapman Young, William L. Fourney, Richard D. Dick

During 1981 and 1982, an extensive oil shale fragmentation research program was conducted at the Anvil Points Mine near Rifle, Colorado. The primary goals were to investigate factors involved for adequate fragmentation of oil shale and to evaluate the feasibility of using the modified in situ retort (MIS) method for recovery of oil from oil shale.

Jan 1, 1985

By A Lance McAnuff, Robert T. Booren

Construction of a dock facility for the Lake Erie Development Project of Stelco Steel involved underwater blasting in commercial fishing waters near Port Dover, Ontario. The most stringent environmental constraints were imposed and a monitoring program involving water overpressure recordings, using equipment developed specifically for this assignment, correlated with observation of caged fish specimens at various distances from the blast source, was undertaken to determine the effects on fish life and to establish whether a protective air-bubble curtain system should be installed around each blast area.

Jan 1, 1989

By Richard W. Watson, Julius Roth

The Bureau of Mines has recently completed a contract study of the hazards associated with surface mining.! Part of this effort involved an analysis of surface mining accidents associated with blasting activities. For this purpose, 71 reports of accidents investigated by the Bureau of Mines or the Mining Enforcement and Safety Administration (MESA), covering the period from 1962 to 1976, were collected and analyzed. In addition, blasting accident frequencies for the period 1973-1976 were extracted from the central computer files maintained by the Health and Safety Analysis Center (HSAC) in Denver, Colorado. This paper presents a preview of the findings, which are treated in more detail in the final report.

Jan 1, 1978

By H Fukui, K Ichikawa, K Aikou, E Suzuki

An electronic delay detonator (EDD) consisting of a digital-base electronic delay module and a conventional instantaneous detonator module, designed for series connections with a special adjustable-output blasting machine, is described and shown to provide a delay time accuracy some four to twelve times higher than that of pyrotechnic millisecond and decisecond delay detonators, together with the other performance characteristics necessary for practical use. Also described is a blasting design system which allows effective reduction of ground and air vibration, through the use of EDDs with optimum delay times as determined by accurate computer simulation based on wave form and other data obtained from an on-site single-shot test blast.

Jan 1, 1989

By Charles E. Joachim

Railroad and blast induced vibrations were measured in the vicinity of the proposed Big Bend Cutoff. Peak horizontal and vertical particle velocity relations were developed using least squares regression analysis. The dominant frequencies of these data are in the range of 30 to 50 hz. Therefore, allowable charge weight per 30 msec delay curves were generated for buildings (2 in./sec) and unlined tunnels (8 in./sec). A blasting contour map is presented for this site.

Jan 1, 1984

By Lina Lopez, Jose Sanchidrian, Manuel Lopez, Pablo Segarra

Previous work in which rock properties and blasting parameters (geometry, charging and timing) were reported together with truck filling times, is taken as a starting point for a thorough analysis of the influence of the former on the mucking velocity. The experimental set was composed by 11 blasts made in an open pit mine. Non-parametric, distribution-free statistics is applied. The mucking rates (in bank cubic meters per unit of bucket volume and per hour) appear to be clearly dependent on the explosive energy and powder factor, both magnitudes combined as energetic powder factor (energy per unit of rock volume). The mucking rate is a non-monotonic function of such factor in the range of the blasts analyzed. The determination of the function is optimum when the fraction of the explosive below grade is not considered and when the explosive energy is qualified as that delivered at a partial detonation regime. Different types of loaders seem appropriate for different energy levels. At low levels both front loaders and rope shovels obtain small productivities without a statistically significant difference in their performance. At high energy levels, front loaders qualify higher than rope shovels. Mucking velocities can be equally small at low energy powder factors and at high ones if rope shovels are involved.

Jan 1, 2008

By Gungor Tuncer, Erhan Bakirci, Ali Kahriman, Atilla Ozmen, O. Nuri Ucan, Savas Gorgun

There are several methods for demolition of structures but most of them depend mostly on conventional ways of using machines for breaking and crushing structural elements. However the need for lots of work force, expense and extreme amount of time for demolition, made most of these methods non-popular nowadays. Therefore, trials to accomplish a more economic and less time taking method lasted with the use of blasting. By applying controlled blasting on a suitable structure, the structure can collapse and break down to pieces in very short period of time, with no extra work force and cost. In spite of advantages of explosive demolition, the potential danger of explosives and the damage that the blasting may cause to surrondings, if not controlled properly, made people timid to the method especially in urban areas. Therefore, the pre-assumption by computational analysis has become an essential matter in the process.

Jan 1, 2002

By Navid Mojtabai, Jaak J. K Daemen

Some facilities require ground vibration limits that are far below typical vibration levels of interest in most blasting situations. A possibly extreme example of such a facility might be the proposed SSC (Supercollider Super Conductor) high energy particle study system. The applicability of conventional blast vibration predictors for such a low amplitude vibration is highly uncertain. For this preliminary study, a series of field measurements are made, and the results integrated in a set of vibration predictor equations. Ground vibrations induced by blasting operations at one proposed SSC site are monitored at close distances (hundreds of feet), intermediate distances (miles), and long distances (tens of miles) from the blasts. Peak particle velocities are recorded at short distances, ground displacements at other points, as well as frequencies. Theoretical analyses are performed by integrating all data in a variety of ground vibration predictors. From the statistical analysis of the data, ground motions at various points along the ring site are predicted for a given charge weight. The approach taken appears adequate for making tentative estimates of exceedingly low amplitude vibrations at great distances from mine blasts.

Jan 1, 1987

By Charles A. Kliche

The Comprehensive Environmental Response, Compensation and Liability Act of 1980 (CERCLA) established a national program for responding to releases of hazardous substances into the environment. The funding mechanism for this program is the Hazardous Substance Response Trust Fund (commonly referred to as Superfund), which provides funding for the implementation of removal and remedial response actions.

Jan 1, 1997

By R Frank Chiappeta, Eduardo Nixon, John Dean Smith, Tom Treleaven

"The creation of the Panama Canal was far more than a vast, unprecedented feat of engineering. It was a profoundly important historic event and a sweeping human drama not unlike that of war. Apart from wars, it represented the largest, most costly single effort ever before mounted anywhere on earth. It held the world's attention over a span of forty years. It affected the lives of tens of thousands of people at every level of society and of virtually every race and nationality. Great reputations were made and destroyed. For numbers of men and women it was the adventure of a lifetime.

Jan 1, 1998

By R A. Farnfield

Measurement of the environmental impact of ground vibration from blasting operations is based almost exclusively on the peak vibration level generated. This measurement is known as the Peak Particle Velocity or PPV. The recorded PPV is used to assess the impact of the vibration both in terms of structural damage and human response. Limits for vibration are almost universally quoted in terms of PPV levels and, as a consequence, blast design for vibration control is centred around techniques for the control of this peak value.

Jan 1, 1996

By Donald D. Eilers, Pharis E. Williams, Thomas O. McKnown

The Continuous Reflectometry for Radius vs. Time Experiment (CORRTEX) system was developed by the Los Alamos National Laboratory for determining the energy released in a nuclear explosion by measuring the position of its shock front as a function of time. The CORRTEX system, fielding techniques, and the methods and software for data reduction and analysis were developed over a 15 year period with hundreds of measurements made on nuclear tests and high explosive experiments. CORRTEX is a compact, portable, fast-sampling, microprocessor-controlled system, based on time domain reflectometry, requiring only a 24 volt power source and a sensing element. Only the sensing element (a length of 50 ohm coaxial cable) is expended during the detonation.

Jan 1, 1995

By Calvin Konya, Theodore R. Myers, Robert Lundquist

The design of a single, large mass blast using ring drilling may take two to three months. This time requirement inhibits the evaluation of multiple designs. It also reduces the flexibility to redesign a blast when a parameter affecting the blast changes. Manual preparation exposes the design of a ring blast to a greater probability of human error. The use of Computer Aided Design (CAD) can help to overcome the shortcomings of manual design preparation. High speed electronic calculation, as well as programming, allow for many designs to be considered before blasting. Parametric programming allows single or multiple parameter changes to be introduced into an existing design, such as changes in drilling equipment, variations in ore density or changes in explosive. Exposure to human error is reduced by programming that performs calculations and produces graphical displays for review by the designing engineer. The goal of achieving desirable fragmentation for the minimum cost, when using ring blasting, is obtainable using blasting design techniques and CAD. Multiple designs can quickly be generated and costed, producing cost curves that indicate an optimum design with respect to cost.

Jan 1, 1990

Fracture Control Blasting is an alternative to pre- and post-splitting or smooth wall blasting. It was developed at the University of Maryland as an attempt to overcome some of the disadvantages that occur with normal blasting practices. There are two main factors that are unique to fracture control blasting. First, it utilizes a notched or grooved borehole to initiate fractures at desired locations and secondly, it employs a very carefully selected charge so as to provide control over borehole pressure. The maximum borehole pressure must be kept between very definite limits in order to obtain initiation of fractures at locations where they are desired and yet not obtain fractures where they are not desired. When coupled with stem induced fracturing, which was developed for oil and gas well stimulation, it has been found that the charge required for fracture control can be as little as 1/40th that required for normal smooth wall blasting. The paper describes the technique of fracture control blasting and gives results of some of the field testing conducted to date.

Jan 1, 1984

By Scott G. Giltner, Paul N. Worsey

During the short duration of an explosive blast, many events occur which are too quick to be detected or observed in detail with the naked eye or by normal photographic techniques. Through the use of "hightech", high speed video, many of these events can be observed, instantly played back and recorded for later use. The use of a Spin Physics SP 2000 Motion Analysis System at a blast casting operation is presented. The variable range of recording speeds offered by the SP 2000 allowed it to be used for examination of different areas of blasts. At its maximum full frame rate of 2000 frames per second the SP 2000 can easily pick up the flame front as it travels down a nonel tube and the flash from the surface delays as they fire. The system was used for a variety of tasks including, but not limited to,the determination of delay accuracy to within 0.5 ms, the velocity and trajectory of the faces during blasts, and pinpointing geological problem areas. The effectiveness of the system as used on site is discussed along with detailed method of set up, recording, playback and data processing. Other details including site specific environmental and lighting problems are also covered.

Jan 1, 1986

By E Emery Jr Gray

A need for more delay periods other than those normally manufactured throughout the explosives industry rarely occurs. This paper will discuss one such incident from an analytical view through practical application.

Jan 1, 1976

By Erik K. Lauritzen, Jorgen Schneider, Niels Madsen

From 1986 to 1988 Kalaallit Tunisassiorfiat (KTU)/Gronlands Hjemmestyres Produktionsvirksomhed (the part of Greenland's own governing body which is in charge of production activities) has been responsible for blasting projects in the following 4 towns: Ilulissat/Jakobshavn, Qasigiannguit/ Christianshab, Qeqertarsuaq/Godhavn, Sisimiut/Holsteinsborg

Jan 1, 1989