Search Documents

By Y. Q. He

The methodology of active pulsing air separation is a new method for dry material classification. Especially, it is suitable to electronic scraps disposal and re-utilization. By studying the difference of drag coefficients of the particles moving through areas of varying Reynolds numbers, and considering the extra-mass forces acting on the particles in the active pulsing air field, models of the dynamic motion which particles follow were developed. A computer simulation was prepared that showed the traces of particles with different densities and/or diameters, but similar aerodynamic characteristics, as they moved through the turbulent flow, to modify and define the parameters of the models. The simulation was found to predict the observed results with artificial tracing spheres being separated by the laboratory equipment. The separation performance, as being affected by the particles, nature, the air velocity, the pulsing frequency and the air pattern, is discussed. In general, lower density particles are more responsive to variations in airflow velocity. In addition, an industrial scale active pulsing air separator was designed, and it provides a new and efficient method for resource re-utilization in China.

Jan 1, 2014

By Alexander E. Sobolev

The kinetics of oxidative dissolution of lead sulfide in solutions of nitric acid and sodium hypochlorite was studied using the rotating disk method and the factor experiment design. The dependences of the PbS dissolution rate on concentration of oxidant (HNO3 or NaOCl), temperature, disk rotation frequency, and duration of interaction were determined. The adequate kinetic models allowing calculating the specific dissolution rate at any combination of values of the influencing factors were obtained. As a result of the complex analysis of kinetic parameters, the modes of the each process proceeding were established, their macromechanisms were determined, and the limiting stages of the oxidative dissolution processes were revealed. The dissolution kinetics of lead sulfide in solutions of nitric acid was found to have several regimes. At HNO3 concentrations below 0.5 mol/L, the process proceeds in a mixed mode close to a diffusion-controlled. It is caused by low oxidative activity of HNO3 and considerable diffusional diffuculties at this acid concentration range. At the nitric acid concentrations more than 0.5 mol/L and less than 6.0 mol/L, the process was found to be kinetically controlled. The limiting stage of the interaction is the surface chemical reaction. The observed relatively high order of the dissolution rate with respect to the concentration of HNO3 was explained by the autocatalytic action of the acid reduction products. At nitric acid concentrations exceeding 6 mol/L, the process proceeds in a mixed mode close to a diffusion-controlled, and the dissolution rate sharply decreased that was explained by a decrease in the solubility of reaction products. When lead sulfide is dissolved in sodium hypochlorite solutions, at first time the amount of PbS transferred into solution remains close to zero. Gradually, as time goes, this amount begins to increase sharply. The dissolution rate rises and reaches the maximum value, further remaining constant. At the steady-state regime, the dissolution rate is independent of the duration of interaction and disk rotation frequency. The process was found to be kinetically controlled. The limiting stage is likely to be chemical reaction on the surface of solid lead sulfide. The obtained kinetic characteristics enlarge the database on hydrochemical oxidation kinetics of sulfides and can be used for the elaboration of the recommendations for the effective comprehensive exploitation of lead-bearing ores and concentrates. Keywords: lead sulfide, nitric acid, sodium hypochlorite, hydrochemical oxidation, dissolution kinetics

Sep 1, 2012

By Skinner. W.

"Introducing cutting-edge development work, which aims to simplify mineral processing flow-sheets, reduce costs and address environmental issues. Over the past four years Innovative Mineral Processing Technologies Pty. Ltd (IMPTEC) Australia have developed a Super-fine Crusher and a Planar Magnetic Separator which offer low cost, wet or dry alternatives to conventional grinding and conventional magnetic separation. Each of these machines has been successfully trialed at pilot scale and are now in the process of transitioning to commercial scale. This paper reports on the progress made in each of these fields. The potential scope for application of super-fine crushing technology as an alternative to grinding is potentially expansive and could include beneficiation of metalliferous ores, precious metal ore processing, hydrometallurgical processing, industrial minerals and coal processing, plastic fillers and ceramics processing as well as processing of cementitious slags and fly-ash. IMPTEC have recently achieved outstanding results at pilot scale with a dry combination of super-fine crushing and planar magnetic separation, which offers an alternative to the wet processing of magnetic iron ores. The dry combination has set new laboratory performance benchmarks when compared with the industry standard wet Davis Tube Tester. The test results have also established a strong evidence base showing that super-fine crushing achieves liberation of value minerals at coarser sizes when compared with grinding. The dry combination of super-fine crushing and planar magnetic separation also addresses environmental issues and completely eliminates grinding. An IMPTEC super-fine crusher is currently undergoing commercial trials, generating ultra-fine products from granulated lead blast furnace slag for use as cement substitutes. The performance of the super-fine crusher on this extreme duty highlights the potential benefits of super-fine crushing over the wide range of industries and applications where conventional grinding is employed.INTRODUCTION Present day mineral processing practices can become anchored in convention, where, inefficient methodologies are recognized and accepted as “best practice” or “industry standard”. Motivated by this challenge, IMPTEC has undertaken the development of radically different and improved methodologies in the fields of fine comminution and magnetic separation. Whilst, crushing is much less energy intensive and generally less capital and maintenance intensive than grinding, the technology has stalled due to the lack of crushing devices, which have the capacity to adapt to fine and ultra-fine duties. Grinding practice advances have been achieved through major increases in machine size and power. However, these advances are also accompanied by major escalations in capital, operating and maintenance costs. The economics of this strategy has become increasingly questionable. A typical example is the viability of low-grade magnetite beneficiation, which can hinge largely on the cost of grinding to fine and ultra-fine liberation sizes."

Jan 1, 2018

By Santiago Garcia, Dariusz Lelinski, Devan Govender, Tyson Baker, Mads Jespersen

"In recent years, the scale-up of mechanical flotation machines has been attempted with greater frequency. In contrast, the development of rotor-stator designs has been subject to greater inertia. The rotor-stator components are integral to the operation of mechanical flotation machines, responsible for the key physical processes of solids suspension, gas dispersion and energy dissipation. Design modifications are predicated upon the dual purpose of meeting customer needs while achieving metallurgical performance objectives. Accomplishing the latter is a rigorous undertaking, typically involving the sequential application of fluid dynamics principles, prototyping, smaller-scale research screening studies and larger-scale development projects. This industrial evaluation details the final stages of the forced-air rotor-stator development process using a double-refractory Carlin-type gold ore. A bypass stream of the primary rougher feed was further classified into cyclone underflow and overflow products. Four rotor-stator treatments were evaluated using parallel flotation rows coupled with a randomized statistical design. Only two treatments are compared in this initial assessment. Metallurgical responses were measured as a function of the random variation of key machine factors. Machine characterization measurements complemented the analysis of flotation performance indicators."

Jan 1, 2014

By I. Zh. Bunin, G. K. Khachatryan, N. E. Anashkina

For optimization of diamond processing technology the influence of nanosecond high voltage pulses on mechanical and technological properties of diamond crystals and kimberlite rock-forming minerals (calcite, olivine, serpentine) was investigated. Using methods of Fourier Transform Infrared Spectroscopy (FTIR), X-ray photoelectron spectroscopy (XPS), microscopy and mikrohardness measurement the changes of structural, physic-chemical surface properties, and microhardness of minerals as the result of impacts, was studied. Non-thermal impacts caused a decrease of kimberlite rock-forming minerals microhardness in general to 40-66% as the result of surface microstructure destruction which is caused by formation of micro cracks, traces of surface breakdown and other defects. At the same time, the pulse energy impact on natural diamonds led to formation of B2 type crystal lattice microsift defects, elevated concentration of which increases the hardness properties of crystals. The obtained result indicates possibility of applying pulsed energy effects to improve the softening efficiency of diamond-bearing kimberlites rock-forming minerals without damaging the diamond crystals and ensuring their preservation by the subsequent grinding of ores. By IR and X-ray photoelectron spectroscopy revealed that processing by hight voltage pulses causes a change of natural and synthetic diamonds surface functional cover composition. Short-term exposure (~ 10 - 30) leads to detachment and partial destruction of secondary phases mineral films on the surface of natural technical diamonds, increasing floatability and hydrophobicity of crystals. However, with increasing duration of treatment (~ 30 - 150) occurs surface hydroxylation (found by XPS for synthetic diamonds), as a result of diamond surface layer oxidation. The effect of increasing the natural diamonds flotation activity by 14% (from 47% to 61%) was experimentally established as a result of processing diamond crystals with nanosecond pulses (~ 10-50 sec), which indicates the principal possibility of using pulsed energy impacts to intensify the diamond flotation during processing diamond-bearing kimberlites.

Jan 1, 2018

By Shankar Narasimhan

Data Reconciliation is a technique that has been developed more than fifty years ago and has been refined over the past few decades and is now being deployed routinely in several process industries such as refining, petrochemicals, mineral processing and hydro-metallurgy. The main aim of data reconciliation is to obtain accurate estimates of all process variables and parameters using plant measurements that are invariably corrupted by random errors and may also contain biases and other gross errors. These reconciled estimates are subsequently used either in offline exercises such as simulation, retrofitting, and de-bottlenecking or in online optimization and control applications. In this presentation, a brief history of data reconciliation, its assumptions, and uses are reviewed. New developments in this area are highlighted such as robust data reconciliation to handle model uncertainties, and reconciliation using identified models derived purely from operating data. Several case studies in the mineral processing industries reported in the literature are also highlighted to indicate the potential benefits of this technique.

Sep 1, 2012

By V. Z. Kozin, E. A. Bekchurina, P. S. Volkov, Yu. P. Morozov, A. S. Komlev

"The current sampling systems of ore flows or concentrates are based on the method of cross sections in point sampling and the method of scooping in reducing. The limited number of point samples in sampling and microsamples in reducing lead to big random and probable systematic errors. The paper defines the principles of sampling, which assure the absence of systematic errors and also provides calculation formulas of probable errors in sampling methods of cross and longitudinal sections as well as in samples preparation. The article sets the fundamental laws of sampling: the dependency of minimal mass of gross sample and number of point samples from mass of point sample in sampling from heterogeneous body; the dependency of a sample minimal mass from lumps’ size in preparation of carefully mixed samples; the dependency of point samples’ dispersion from duration of control period. The paper introduces the fundamental notions: lump variance; probable systematic error; methodical error. It also provides a solution of outstanding sample correct application in analysis results calculations. In application of automatic analyzers, mounted in material flows, the probable error connected with sampling, is calculated by the formulas for carefully mixed sampling bodies. The paper describes the developed and introduced sampling systems on the base of combined application of cross and longitudinal sections methods in sampling and preparation of samples. The advantages of this equipment are compactness, reliability, simplicity in service and operation, and for pulps it is adaptability in pipelines. Application of the developed equipment entirely excludes probable systematic error. The new systems of sampling and preparation of samples are introduced at 25 concentrating plants. Introduction of the developed systems at sampling balance points of concentrating plants allowed double reducing balance deficiency."

Jan 1, 2018

By M. Kadiyski, V. Stoyanova, E. Visariev, V. Stoilov

"The present study deals with copper losses in slag from copper smelting. Copper slag cooling at Aurubis Bulgaria is traditionally done in pits. A new type of slag-cooling is introduced in the site, involving cooling ladles. In a previous study, the ladle cooling process was studied in detail, showing an improvement in the recovery of copper in the slag after flotation. The main reason for better recovery of copper is the increased cooling time, which allows for the accumulation and aggregation of copper droplets. The effects of the newly introduced slag cooling process are studied using optical microscopy and scanning electron microscopy. Cooling in pits and in ladles is compared, based on copper droplet size, distribution and content. Specialized image processing software is employed on images taken with an optical microscope. The results are then compared with a similar technique, available in SEM software. The availability of phase-analysing image software in combination with electron dispersive X-ray spectroscopy makes it possible to study the morphological properties, distribution and chemical composition of the copper droplets. The obtained results confirm the initial conclusions about size, distribution and composition of the copper-bearing particles. A large amount of copper particles is examined showing an obvious increase in their size from pit- to ladle cooling. The results show an increase in the average size of the droplets, which doubles from pit-cooling to ladle-cooling. There is a well-pronounced tendency of decrease of the percentage of droplets in the smallest fraction (<5 µm) in the ladle-cooled slag. In addition, the number of droplets in the larger fractions increases, compared to the ones in the pit-cooled slags. It is believed, that the developed methodology for analysis provides a relatively quick and reliable solution for comparison of the cooling rates in the slag. INTRODUCTION In the process of copper smelting and converting, iron-silicate slags are produced that contain various amounts of dissolved and entrained copper. Different physical and chemical techniques are employed for the valorisation of the remaining metals in the slag – magnetic separation, leaching, roasting, flotation, etc. According to Gorai et al (2003), about 2.2 tons of slag is produced per ton of metal. In 2016, about 20 million tons of copper have been produced globally (www.icsg.org). At an average of 0.5 percent copper content after treatment, these slags contain more than two hundred thousand tons of copper which is lost due to inefficient processing."

Jan 1, 2018

By A. Güney, G. Önal

"Karagedik Chromite Concentrator of the ETI Holding Co., which is located in Fethiye (south Turkey), has been producing chromite concentrate assaying 47-48 % Cr2O3 from the chromite ores containing 30-35 % Cr2O3 by using gravity separation methods since 1920. The tailings having 13-14 % Cr2O3, which had been removed from this plant, were accumulated at the stockpiles amounting about 1.2 million tons. In order to recover the ultra fine chromite particles from the Karagedik Concentrator tailings, the new process including Wet High Intensity Magnetic Separation and column flotation, was developed and the Karagedik Research Pilot Plant based on this process was commissioned in 2000. At this plant, the final concentrates assaying 46-48% Cr2O3 were produced and overall plant recoveries are about 60-65%.At the chromite concentrators using gravity separation methods, if their material size is about minus 1.0 mm, chromite particles especially pass to fine fractions according to their mineralogical structures and the ore-genesis (Önal and Güney, 1990). Generally, after crushing and grinding, the shaking tables and spirals are used at the chromite concentrators; therefore fine size chromite particles (-0.038 mm) are removed as tailings. Cr2O3 content of the -0.1 mm size fraction with 52.3% of the total amount is 19.58 % with Cr2O3 distribution of 82.6%.In order to upgrade the minus 0.1 mm size fraction of the tailings, assaying about 20% Cr2O3, Karagedik Research Pilot Plant (KRPP), which includes Wet High Intensity Magnetic Separator (WHIMS) and Column Flotation units, was installed by Istanbul Technical University (ITU), Mineral Processing Section in 2000.Feeding material of the KRPP having 5 tons per hour capacity is obtained from stockpiles amounting 1.2 million tons. After attrition scrubbing, the feed is sent to a screen with aperture of 1.0 mm. The screen overflow, assaying 5-6 % Cr2O3 is removed as tailings. Screen underflow is classified to –1.0+0.1 mm and minus 0.1 mm size fractions by using cyclone and sieve bend. –1.0+0.1 mm size fraction assaying 6-7 % Cr2O3, is sent to existing gravity separation plant. Minus 0.1 mm size fraction is firstly fed to WHIMS for pre-concentration and non-magnetic product assaying 10-11 % Cr2O3 consisting of serpentine, talc and olivine minerals are separated as tailings. Also magnetic product (25-30 % Cr2O3) obtained from WHIMS is fed to the two stages conditioners after dewatered to 30 % solid ratio."

Jan 1, 2003

By Reza M. Rahman, Seher Ata, Graeme J. Jameson

"This paper presents the results of a through investigation into the froth recovery measurements in a controlled plant environment using a device that allows direct collection of dropback particles from the froth phase. Test work was performed at the Northparkes concentrator (NSW, Australia), using a feed taken from the head of the cleaner scavenger bank. The feed slurry had a relatively higher copper grade varying from 5.2% to 6.8%. Experiments were performed to investigate the effect of important flotation parameters such as air flowrate on the froth recovery. The size of the particles in the relevant streams was also analysed to acquire in-depth knowledge about the froth dropback mechanism. The results suggested that the froth recovery could be as low as 70%, although it was relatively easy to achieve the values in the range 75% to 85% by the correct choice of operating variables. It was found that the air flowrate has a positive impact on both collection (pulp) and froth zone recoveries. However, the effect was more prominent in the froth zone. It appeared that the froth recovery is a strong function of particle size."

Jan 1, 2014

By Erico Tabosa, Meng. Jun, Kym Runge, Matthew Brennan, Weiguo Xie, Dee Bradshaw

Turbulence and its distribution are of great importance in flotation cell design as they affect suspension of particles, air dispersion and particle-bubble collision rates, which in turn determine flotation performance. However, there is no mature technique to measure turbulence in three phase (liquid-solid-gas) systems such as in flotation cells. In this article, the authors present two new approaches that are suitable for measuring turbulence distribution in three phase systems and validate their applicability. The first technique uses a piezoelectric vibration sensor (PVS) to measure fluid kinetic energy standard deviation and the second technique applies electrical resistance tomography (ERT) to measure conductivity variation at a measurement position in a flotation cell. For the PVS technique, calibration of the sensor was performed to determine the values of parameters that were needed to calculate the force applied to the sensor. Then measurement was conducted in a 60L batch flotation cell and the results were compared with LDA measurement. This demonstrated that the piezoelectric sensor signal provides a good representation of fluid kinetic energy standard deviation at the position of measurement. For the ERT technique, conductivity distribution data was processed to give conductivity variations, which were then used to calculate fluid kinetic energy standard deviation at the measurement position. The spatial distribution of turbulence obtained by performing multiple measurements at different positions in the 60 litre batch flotation cell was found to agree with the PVS measurement results. These two techniques are potentially powerful tools for turbulence measurement in flotation environments, enabling a clearer understanding of turbulence’s influence on flotation performance to be determined.

Jan 1, 2014

By M. Wright, A. H. Mwale

This paper examines the combination of unit technologies in a minerals beneficiation train, and explores the inter-relationship between energy input and water consumption for a given mineralogy and product recovery, as these are two critical environmental issues which affect the overall viability of many minerals plants. In particular, we review constitutive relationships for each of the sub-processes of comminution, flotation, and tailings dewatering, and suggest how these might be integrated into a unified hybrid model, with particle size distribution as the key design variable. Such a model can then be used to explore the trade-offs between different performance objectives (be these technical, economic or environmental) as part of a multiple-objectives optimisation exercise. In this way, it may become practical to envision situations in which concentrate grade and recovery are sacrificed, marginally, in order to reduce energy demand in comminution, and improve overall water recovery. This becomes more relevant as the industry commits to advancing the sustainable development agenda in the face of the increasing life -cycle costs and impacts of minerals processing operations, coupled to declining ore body grades, and the desire to maximise recovery of minor and trace elements. Some specific observations for copper are offered.

Jan 1, 2003

By B. S. Moroney

Elemental distribution varies widely in the ores, minerals and beneficiated products depending on the constituents. Accurate analysis of each element present in various beneficiated products is utmost required to assess the grade in view of zero waste technology. Hence, the suitable methods and instrumental technique is of prime importance as the distribution of various elements differs in the beneficiated products. Conventional classical technique of analysis is absolute and due to this, it has not become obsolete. Besides, it is much needed for making standards for various relative techniques. Instrumental techniques comprising of X-ray fluorescence, Induced Coupled Plasma Analyzer, Carbon-Sulphur Analyzer, Atomic Absorption Spectrometer etc. are important for quick and accurate analysis. However, the selection of these instruments depend on the nature of material to be analyzed. This paper highlights the importance and use of various methods/techniques and instruments involved in the analysis of various ores, minerals and beneficiated products. Keywords: wet classical, x-ray fluorescence, induced coupled plasma analyzer, atomic absorption spectrometer

Sep 1, 2012

Flinders Power, formerly NRG Flinders, is considering the possible use of low rank coal from Lake Phillipson, South Australia (SA) in its power stations at Port Augusta, SA. Typically, this coal contains about 35% moisture and 10% ash. Unfortunately, it also contains high levels of sodium (1% Na) and chloride (0.95% Cl) with a Na2O level in ash of 18.9%. Such levels cause serious problems during coal combustion, making the use of as-mined coal impractical for power generation. This paper describes the development of an aqueous leaching technique to remove 90% of the sodium and chloride and to yield a product with a Na2 O level in ash of less than 3%. Small-scale agitation leaching tests with good quality tap water at ambient temperatures showed that the coal needed to be crushed to minus 5.6 mm to obtain maximum removal of water-soluble sodium and chloride in 30 min. Leaching kinetics, but not the ultimate removal of salt, were enhanced by the use of higher temperatures (up to 150°C), but this was deemed uneconomic. Varying the pulp density between 20% and 50% had little effect on extractions and there was no benefit in multiple stage water washing. The best results by water leaching were 69%~74% extraction for sodium and 95%~97% for chloride, meaning that the sodium removal was well below the target level. From SEM examinations of the leached product it was concluded that the remaining sodium was organically bound to the carbon atoms in the coal. Further tests using aqueous solutions containing cation exchange additives such as calcium chloride (CaCl2) or ammonium chloride (NH4Cl) or sulphuric acid (H2SO4) showed that significantly enhanced sodium extractions were possible and target specifications were met. Two options, namely a single-stage and a two-stage leach, were then investigated. In a single-stage leach with additive, minus 5.6 mm coal was leached at 33%~50% solids for 30 min at ambient temperature and then filtered and washed with fresh water. This gave a sodium removal level of about 81% and a Na2O level in ash of about 5%. These levels do not quite meet tar-get specifications. In a two-stage leach, the coal was first leached with water alone without an additive as in the single stage leach, and the washed residue re-leached under similar conditions for about 5 min with an additive (CaCl2), and then filtered and washed. This gave a cumulative sodium removal of 96% and a Na2O level in ash of 1.4%~2.4%. These levels are well within target specifications.

Jan 1, 2014

By Y. H. Tang, H. Y. Zhang

"Tailings from lead-zinc mine contain plenty of dolomite and low-grade fine-grained barite, which is difficult to enrich by mineral processing. Since the density of barite and dolomite has some differences due to the fine dissemination size in a complex sedimentary, the gravity separation tests were conducted with no results obtained. The magnetic separation was conducted to remove the magnetic gangues, and the results were not satisfactory because of the gangue minerals such as limonite and others were low in content. The results of floatation tests showed that the mineral separation of barite and dolomite is quite difficult because that they have similar mineral floatability. Experimental research shows that the good results can be obtained by “desulfurizationbarite floatation” processing with the new depressant TS. The barite concentrate containing BaSO4 91.27%, BaSO4recovery is 70.25% when sodium dodecyl sulfonate serves as a collector and TS as the depressant.INTRODUCTIONBarite is an important mineral material. Often associated with other minerals, it usually needs to be separated by mineral processing in order to meet the application requirements. The main barite beneficiation methods include hand sorting, gravity separation, floatation, magnetic separation, acid leaching, etc. Usually barite associated with oxide ore such as fluorite dolomite, quartz ore etc. are also associated with sulfide ore such as pyrite, sphalerite and galena. The separation between barite and sulfide ore (such as pyrite) is easy. On the other hand, the separation between barite and oxide ore (such as dolomite and fluorite) is very difficult. There are quite a lot of reports on the separation between barite with fluorite dolomite however the separation between barite and dolomite is seldom discussed.The ore properties are quite complex attributable to mineral assemblage containing a large amounts of dolomite. As the density of barite and dolomite has some differences, gravity separation between them is usually easy. The gravity separation tests were conducted with no results obtained due to the fine dissemination size in a complex sedimentary. The magnetic separation was conducted to remove the magnetic gangues, and the results are not satisfactory as the gangue minerals such as limonite and others were low in content. Due to the fine dissemination and intimate association of minerals, and barite and dolomite contain the same group ions of Ba2+, Ca2+ and Mg2+, the results of flotation tests showed that the mineral separation between barite and dolomite by flotation means problematic. Previous studies have been conducted by several institutions but none to date has come up with a satisfactory process in dealing with the deposit. This may be attributable to: high cost of reagents; unsatisfactory performance. Therefore, the key to the flotation separation of barite and dolomite is the application of selective inhibitors. Based on previous test observations and years of extensive research experience in barite processing technology, with the new depressant TS has selectivity inhibition on dolomite developed and used, good results can be obtained by “desulfurization-barite flotation”, which allows barite in the lead-zinc tailings to a comprehensive recovery."

Jan 1, 2018

By R. Prakash

Column flotation has now gained wide application in the recovery of various minerals. The performance of the flotation device depends on the mixing characteristics of the phases inside the devices. In this work, quality of mixing in a flotation column has been analyzed by using information entropy theory. Empirical models have been developed for flotation column with the parameters which affect the quality of mixing. The efficiency of the particle separation in the flotation column has been enunciated based on the quality of mixing. The present analysis on the quality of mixing in flotation column may give insight into a further understanding and modeling of flotation devices in industrial applications.

Sep 1, 2012

By Rod Hocking, Nenad Djordjevic, Randolph Pax

"Semi Autogenous (SAG) mills exhibit complex interactions between the competing processes occurring inside them. Traditional practice is to measure the operation of the SAG mill at an operating point in terms of its load, power draw, steel load, ore throughput rate, water addition rate and more recently the feed size distribution. However significant departures of operating conditions can occur due to changes, for example, in ore hardness, the quest for higher throughputs and mill internal geometry.Fundamental to SAG mill operation are the internal processes that ensure that a given ore throughput and discharge grind size are obtained and maintained. These processes can be measured using non-contact acoustic emissions from the SAG mills which utilise the information rich noise that is generated by the grinding, flow and charge movement inside a mill.Non-contact acoustic in-mill measurements can be used for the validation of discrete element modelling (DEM). The approach being reported in this paper is to model the individual physical processes and then to simulated the assemblage of a physical mill."

Jan 1, 2003

By Rintaro Hayashi

The enrichment of useful components from ores and/or wastes has become important with increasing recent worldwide resources demand and the amount of wastes generated from the urban mines, in order to establish real ?sound resource-cycle society? including the activity of resource exploitation. The first stage of the treatment in the process must be comminution and it is important to make good liberation among compositional phases in the targeted resources. Electrical disintegration (ED) is well known to make a selective breakage at phase boundary. However, the detailed mechanism of the phenomena is not clarified yet, in especial, on the influence of electrical properties of compositional materials on the liberation. This paper made a comparison between the liberation degrees of ED products and the results of electromagnetic field analysis using finite element method (FEM). In the experiments, we used several synthetic cement paste based samples in which mineral particles were dispersed to apply the ED, and in the electromagnetic field analysis, we calculated the charge density accumulated and the Maxwell stress at phase boundary. It was found, for highly insulating mineral samples, that higher breakdown voltage was necessary because electric charge was not easily accumulated at phase boundary but that higher liberation degree was obtained after the breakdown (ED). It was also found the tendency that higher liberation was observed for the samples which had higher maximum Maxwell stress calculated by the electromagnetic field analysis. From the results, the electrical charge and Maxwell stress induced at phase boundary could be driving forces of selective breakage. In addition, we also applied the ED to the printed circuit boards (PCBs) in order to concentrate miner rare metals, which were essential for producing electronic devices. It could be demonstrated that the devices installed on the PCB were easily detached from the board and that most of metal elements in the devices was exposed and liberated from the insulating plastic covers, which were broken in the ED, then, it is considered that the subsequent solid phase separation could be effective for concentrating such metal elements. Keywords: liberation, electromagnetic field analysis, printed circuit board, miner rare metal

Sep 1, 2012

By I. Gombköto

Mining and mineral processing operations are usually generating huge amount of tailings. These tailings often gives lots of maintenance work in order to protect environmental resources from heavy metals slowly leaching out of tailing are due to Acid Rock Drainage (ARD) process. Handling leakage could be active or passive such as using of Permeable Reactive Barriers (PRB). PRB?s are used worldwide treating underground contaminations, using different type of matrix materials. All generally used matrix material has its advantages and disadvantages such as selectivity, sensitivity of precipitation generation or not satisfying hydraulic conductivity. Nowadays cheap and effective matrix material which is ignorant to pore plugging caused by precipitation within the PRB could be one solution to the demands of the industry. The authors have been carried out an investigation at University of Miskolc on lignite as high humid acid containing material for determining the ability of heavy metal adsorption and pore plugging resistance. Moreover, using hydraulic and chemical simulation methods, complete PRB dimensioning protocol based on new lignite matrix had been introduced. Within the frame of this paper the results are going to be discussed.

Sep 1, 2012

By M. Brennan, A. Majumder

"The mineral processing research community has devoted enormous efforts to the modelling of mineral separators over the last 50 years. While many efforts have been made to use only fundamental physics as a basis for the models, fluid flow patterns in separators are not simple while the motion of particle swarms through fluids is extremely complex.One of the simplest separators is the sluice, in which separation takes place in a flowing film a few millimetres thick. The particles are suspended by turbulent eddies and motion relative to the fluid takes place in so-called hindered settling mode.In an effort to test the extent to which fundamental fluid mechanics can provide a prediction of particle separation, a study on a simple parallel-sided sluice has been carried out using glass beads at various particle concentrations and flow rates.The actual particle separation taking place was compared to predictions made by first describing the fluid flow by a modified ‘law of the wall’ model.Particle concentration distributions were described using Hunt’s sediment transport model, assuming the particle eddy diffusion coefficient to be the same as that for the water. Settling velocities were calculated using either the Richardson and Zaki or Brauer and Thiele models. The latter takes into account particle size and density distributions and solids volumetric concentration.The resulting predictions of particle separation are remarkably good, even though the model does not model the local settling velocity in the slurry."

Jan 1, 2003