Search Documents

By Y. Shu, A. R. Laplante

"A laboratory Knelson Concentrator (LKC), 7.5 cm in diameter, was used to study the performance of a similar unit at plant scale, 76 cm in diameter, This paper reports on sampling and assaying procedures and problems, and discusses the performance of the plant unit.The sampling procedure was based on the extraction of large samples, 5-15 kg, and their complete processing with a LKC, to characterize size-by-size performance. The procedure yielded reliable estimates of overall gold assays, after blatant assaying errors were corrected. The plant centrifugal unit concentrate was sampled in situ, which yielded very erratic grades, with a large overall negative bias. Due to the very heterogeneous nature of the concentrate, which can be linked to flow patterns in the riffles of the unit, it is recommended that for future testwork, the concentrate be recovered separately, blended and then sampled.The plant centrifugal separator, when operated at a feed rate of 25 t/h, yielded total and free gold recoveries of 41 % and 62%, respectively. This is much lower than previously reported data, and suggest that at 25 t/h, the unit is overloaded. However, recovery did not decrease with time over a loading cycle of 2 hours, which suggests that present loading cycles, generally 1 hour, can be significantly increased. INTRODUCTIONThe study of gold gravity circuits is plagued with the statistical problem of determining the behaviour of particles occurring with a very low frequency. This problem becomes particularly acute with increasing particle size. For example, considering the average weight of a gold flake in the 840-1200 µm (20/28 mesh) to be about 5 mg (Banisi et al, 1991), a reasonably high grade feed of 10 git would require, for a relative error (standard deviation) of 10% on grade, 100 particles, that is 0.5 g of gold, or 50 kg of 840-1200 µm material (a Poisson distribution is assumed). Gy's formula, for the same data, yields a weight of 33 kg, with a shape factor of 0.1 and a size distribution factor of 0.5. Both results are comparable; to obtain the suggested weight of material, a stream containing 5% weight in the 840-1200 µm would require 1 tonne samples (of unsized material). The problem rapidly disappears with decreasing particle size. Still with Banisi et al's data, a gold flake in the 300-420 µm range averages 0.5 mg in weight; the same 10% error on grade corresponds to a weight of 5 kg. Gy's formula for the same size distribution and particle shape factors as above predicts a required mass of 1.4 kg. This would correspond to an unsized sample weight of 10 kg with 14% weight in the 300-420 µm, for example."

Jan 1, 1992

By Gianni Bartolacci, Patrice Nadeau, Szatvanyi. Gerard, Carl Duchesne, Claude Chrétien

"Combustion is used throughout the mineral processing industry to produce steam in boilers, to dry concentrates in rotary dryers, and to apply heat treatments in pyrometallurgical furnaces. Tight combustion control is very important in latter type of furnace since the combustion conditions directly affect final ore quality. However, achieving tight combustion control is not straightforward since most of the flames encountered in industry are turbulent non-premixed flames, they are affected by several unmeasured disturbances and are often produced by burning several types of fuel simultaneously, some of them coming from other parts of the plant. A novel method is proposed in this paper to improve process and product quality control as well as to optimize the combustion conditions based on digital flame color images. Multivariate Image Analysis and Regression is to used extract the flame color characteristics from images to predict the solids discharge temperature of an industrial rotary kiln. It is shown that this method yield extremely good 10 minutes ahead forecast of the temperature and should lead to a substantial reduction in product quality variability as well as in fuel consumption.INTRODUCTIONFuel-fired furnaces are often used in the mineral processing industry for various purposes, such as for the production of steam (utility boiler), in conjunction with rotary dryers to dry mineral concentrates or in pyrometallurgical processes for induration, roasting, and so forth. These furnaces are necessary in the supply chain from the mine to the metals, but their operating costs are constantly rising due to the fluctuations in fuel prices. Moreover, these processes are now targeted by the Kyoto Protocol since they are energy intensive and they produce significant amounts of CO2 and other pollutants such CO, NOx and SO2. To achieve both a reduction in operating costs (i.e. fuel consumption) and in pollutant emissions while maintaining or improving product quality, one needs to have a very good control of the combustion process."

Jan 1, 2005

By B. Haugrud, E. McConaghy, M. Collins, G. Smith

"Laterite ore processed by the Ambatovy Joint Venture in Madagascar is primarily limonitic in nature, containing about 40 to 45 wt.% Fe and 1.1 wt.% Ni. The process selected for treatment of this ore considered the behavior and deportment of iron in each step of the commercial flowsheet. Such considerations included nickel and cobalt recoveries, reagent consumptions, liquid-solid separation characteristics, and both intermediate and final product purities. In this paper, the results for the first three years of commercial operation at Ambatovy are compared with the design parameters, with emphasis on the behavior of iron.INTRODUCTION The main component of nickeliferous laterite ore is iron, and the Ambatovy deposit in Madagascar is no exception. The Ambatovy ore is primarily limonitic in nature, containing about 40 to 45 wt.% Fe and 1.1 wt.% Ni. Since the nickel content of the ore is roughly one fortieth that of iron, successful recovery of nickel depends on close control of the behavior of iron in the selected process. Exploration of the Ambatovy area, which is located to the east of Antananarivo, the capital of Madagascar, dates back to 1960, when the Malagasy Service Géologique carried out a limited pitting and auger-drilling program. Phelps Dodge Corporation (now Freeport-McMoRan Copper & Gold, Inc.) was granted the mining rights to the property in 1995 and carried out significant resource definition, environmental assessment and engineering studies between 1995 and 2001 (Chou, Rooke, Williams, & Hanks, 2000). In 2003, Dynatec Corporation, which was formed in 1997 by the merger of Dynatec International Ltd. and Sherritt International Consultants Inc., signed a joint venture agreement with subsidiaries of Phelps Dodge to evaluate the Ambatovy Nickel Project. Dynatec then became extensively involved in the development of the project, including process selection and pilot plant testing in Fort Saskatchewan (Collins et al., 2004, 2005, 2009; Collins & Vardill, 2005). Dynatec acquired 100% of the project in 2005 and a joint venture between Dynatec, Sumitomo Corporation, Korea Resources Corporation (KORES), and SNC-Lavalin Inc. (SLI) was formed shortly thereafter to provide funding for further development. SLI was responsible for engineering, procurement and construction management of the commercial facilities. Sherritt International Corporation reacquired Dynatec Corporation, including 40% ownership in the Ambatovy Nickel Project, in 2007. The current Ambatovy Joint Venture consists of an integrated nickel and cobalt mining, processing, refining and marketing enterprise between subsidiaries of Sherritt (40% owner and mine and plant operator), Sumitomo Corporation (32.5% owner) and KORES (27.5% owner)."

Jan 1, 2016

By Malcolm Powell

"The argument has long raged across the oceans as to what the best AG/SAG mill aspect ratio is. The North American practice of a high aspect ratio of two, diameter twice length, through to the South African and Scandinavian practice of an aspect ratio of as low as a 0.5. Within the collaborative P9 AMIRA project the MPRU of the University of Cape Town and the JKMRC of the University of Queensland have been collecting plant data pertinent to this issue over the past four years.The JK SAG mill model developed by the JKMRC is based upon data collected from mills having a range of aspect ratios from 1 up to 2. The maximum mill speed, mill load, and ball filling in the fitted data base were all below the operating range common in South Afr-ica. The extension of the P9 project into South Africa therefore lent an ideal opportunity to collect data in a whole new window of operation that would allow the range of applicability of the semi-empirical SAG model to be greatly extended.At the heart of the differences in aspect ratio is the completely different operating practice for high- and low- aspect mills. The mill filling, mill speed, and recirculating loads of closed-circuit single-stage operation have more influence on the differences in operation than the pure aspect ratio relationship. Relationships for load have been extended to 45% filling, with the modified model showing the measured peak in throughput as the mill filling increases. The ball load relationship now covers fillings of over 30% balls (of total mill volume), thus including so-called SAG-ball mills. The influence of closed circuit operation has been measured. It has been found that a key issue of the high slurry flows associated with closed circuit operation, especially when closed with a cyclone, is the pulp discharge limitation of the traditional grate and radial lifter configuration. It has also been observed that absolute mill length is more of an issue than aspect ratio. Slurry flow along the mill and charge segregation within the load are being investigated on pilot and full-scale mills to provide data for potentially modifylng the perfect mixing model that is used for the SAG mill.Improved understanding of these aspects of SAG mill operation and extension of the JK SAG model to better cover the entire range is allowing serious direct comparison of high- and low aspect mills for the first time. It is the conclusion of the researchers working in this area that there is no one best practice, that in fact mills across the range have their application based on ore type, desired product, available capital and on operating costs. Developing robust designs allows direct comparison of two-stage circuits using high-aspect primary SAG mills, with single-stage closed circuit low-aspect SAG mills. The new operations within South Africa are now considering both circuit types, and data is presented on selections that cover the full range of aspect ratio and operating practice."

Jan 1, 2002

By R. H. O. Wagner

"This paper describes the bench testing, pilot plant studies of alternative flowsheets, to determine the feasibility of gold recovery, by carbon in pulp extraction, in the Schumacher Mill gold flotation tailings. The economics were calculated based on pilot plant recoveries and actual industry operating costs.The economics of the carbon in pulp treatment of the gold flotation tailings were not justifiable. The economics of desliming the gold flotation tailings followed by carbon in pulp treatment were marginal, but favourable. INTRODUCTIONPamour Porcupine Mines, Limited is a gold, silver and copper producer located in Timmins, Ontario. In 1983 the head grade of Pamour's gold ores averaged nine one hundredths of a troy ounce of gold per short ton.Pamour operates two area mills to concentrate the gold ores. Free milling gold ores are processed at the Pamour One Mine mill, whereas the refractory carbonaceous gold ores, and complex gold, silver, and copper sulphide ores, are processed through the Schumacher Mine mill.The complex Schumacher mill feed ores do not all react favourably to flotation methods, consequently this study was commissioned to investigate the feasibility of the carbon in pulp cyanidation of the Schumacher mill gold flotation tailings. These tailings contain ten to fifteen percent of the gold in the mill feed. During the study period, the average grade of the Schumacher mill flotation tailings was nine one thousandths of a troy ounce of gold per ton, or one quarter of a gram of gold per metric tonne."

Jan 1, 1984

By Salvador Gómez, Rodolfo Espinosa, Jaime Bravo, Leopoldo Gallas

"Compañia Fresnillo, S.A. de C.V. - Proaño Mine, is owned by Industrias Peñoles S.A. de C.V. (Peñoles). The Proaño Mine, is one of the richest silver underground mines in the World, and for this reason, production capacity has always being expanded, based on generated reserves. Reserve generation has not being an easy task as this is a vein type deposit.This paper presents the growing stages at the Concentrator, for about the last twenty years; which can be listed as follows:1.,Increase in capacity from 1,000 to 4,500 tonnes per day, at several stages; on the same infrastructure, and without production interruptions.2.,Addition of a new flotation circuit to recover a zinc concentrate with a high silver content.3.,Installation of a semi-autogenous (SAG) mill, to replace a conventional crushing circuit. 4.,Modernization. Installation of an on stream analyser, an automatic reagent dosification system, 4500 ft3 unit cells, pressure filtration, a closed circuit video system to help process monitoring, an automatic ball addition system for SAG and ball mills, and on-line particle size analysers.5.,Silver recovery from old tailings, installing a 2,350 tonne per day treatment plant.INTRODUCTIONIndustrias Peñoles, S.A. de C.V. (Peñoles)Peñoles’ mission is to add sustainable value to non-renewable natural resources. Peñoles seeks to: build long-term shareholder value; provide customers with the highest quality product services; maintain productive long-term relationship with suppliers; develop and promote the capabilities of their personnel; foster mutually beneficial relationship with the communities in which operates; protect and preserve the environment."

Jan 1, 2002

By Graham Davey

"Low speed stirred milling has been employed for many years in the metalliferous and industrial minerals industries. High speed stirred milling is a relatively new method of grinding in the metalliferous process industries. However it has been it has been in wide spread use in the industrial mineral field for over 30 years for various minerals. Many existing metallurgical operations are looking to maximize economic return from existing deposits, requiring new thinking and technologies. By combining low speed and high-speed milling fine and ultrafine grinding efficiency and operating costs can be improved.The correct selection of different fine grinding technologies is covered, when each mill is applicable and when a combination of the VERTIMILL® Grinding Mill and SMD provides the best economic solution.INTRODUCTIONUltra-fine grinding of minerals has been in wide spread use in the industrial mineral field for over 30 years. Within the last 10 years the metalliferous industry has shown interest in the ability to produce ultrafine particles, as chemical, physio-chemical and physical separation processes have advanced to be able to treat ultrafine metalliferous particles. Also as the primary mineral deposits, around the world are depleted, new more difficult deposits must be mined. Existing operations are also looking to maximize economic return from existing deposits, requiring new thinking and technologies.The traditional approach for gold containing refractory material has been to liberate the locked gold by chemically destroying the pyrite through oxidation. Roasting, pressure oxidation, and bacterial oxidation all employ various degrees of temperature, pressure and catalysis to react the pyrite with oxygen to produce iron oxide and sulfur by-products. However all of these methods are economically impacted due to specific operational added requirements and emissions controls. Pressure and bacterial oxidation have very high capital and operating costs."

Jan 1, 2006

By Rodolfo Espinosa

"Industrias Peñoles, S.A. de C.V. in Mexico, has nine mining operations, six managed by Peñoles (base metal mines) and three managed by Fresnillo plc (precious metal mines). Seven of the operations use flotation and the other two are heap leach operations, one for gold and the other one for copper.This paper gives a brief introduction of Peñoles, shows mine locations and describes the main process characteristics of each concentrator. It also presents four of the new operating practices that were implemented over the last four years to improve the economics of the mining operations. These include (1) the use of centrifugal gravity concentrators to increase the recovery of gravity recoverable gold (GRG) and silver (GRS), (2) the use of expert systems to reduce process variability while increasing grades and recoveries, (3) the application of the Six Sigma methodology to key projects to ensure success and personnel development and (4) the use of water chemistry fundamentals to identify chemistry problems and design adequate solutions for improving grades and recoveries.INTRODUCTIONPeñoles was founded in 1887. It is a mining group with integrated smelting, refining and chemicals producing operations. Peñoles is the world largest producer of refined silver and metallic bismuth, the leading Latin American producer of refined gold and lead. It is amongst the world leading producers of refined zinc and sodium sulfate.Peñoles operates and controls six underground mines in Mexico and is the largest producer of zinc and lead of the country. It also produces copper concentrates and cathodes. Through its 77.1% equity stake in Fresnillo plc (a London Stock Exchange listed company); Peñoles is also a significant producer of gold and silver. Fresnillo plc operates three precious metal mines in Mexico. While Fresnillo is the world largest primary silver mine, Ciénega and Herradura are two leading gold mines of Mexico. Figure 1 shows a map of Mexico indicating the locations of the Peñoles mines. The main process characteristics of each concentrator are listed in Table 1."

Jan 1, 2011

By Yannis Faitakis, Simon Bergeron

"This paper describes the implementation of model-based predictive control (MPC) on a vacuum heat exchange network at Alcan's Jonquière Complex. The plant produces alumina from bauxite ore using the Bayer Process.The MPC system was commissioned in 2000, by Alcan personnel and an Advanced Control Engineer from Matrikon. The application has achieved an uptime of about 97%.The benefits were:• Energy savings : 0.5% - live steam reduction• Reduced variation: standard deviation of key temperatures reduced by 50%• Plant throughput increase: via the automated use of surge tanks• Decreased supervision time: by plant operations• Faster and easier diagnosis of problems and plant constraintsThe benefits were higher than expected with a payback time around 12 months.The purpose of the vacuum heat exchange network is to recover energy from a hot stream (pregnant liquor) by transferring it to a cold stream (spent liquor). The system is very tightly coupled, and the main constraints of the multivariable control system are: • to control the many tank levels involved in the process (8 tanks)• to maximize the temperature of the heated streams (spent liquor)• to prevent cooled streams (pregnant liquor) from cooling to below a minimum temperatureThe system includes 9 manipulated, 14 controlled and 2 feedforward variables.The advanced control implementation runs under an expert system environment and provides added flexibility to the overall control strategy."

Jan 1, 2003

By J. A. Allan

OCCURRENCES of salt in Alberta have been mentioned and described by the writer in 1929 (l) and by Cole in 1930 (2). Brine springs occur at a number of places along the valley of Athabaska river north of latitude 56 degrees, and also on the south margin of Salt prairie, twenty-five miles west of Fitzgerald in the vicinity of the 60th parallel of latitude, which is the boundary between Alberta and the Northwest Territories. These salt springs were visited by Sir James Richardson in 1820, and in the same year D. W. Harmon stated that " ... clown Salt river there are several places where almost any quantity of excellent dean white salt may be taken with as much ease as sand along the seashore" (3). One hundred years later, in 1920, when the writer first visited these springs, the "dean white salt" which had accumulated about the springs was about 400 tons ( 4). This paper deals with a thick deposit of rock-salt which has been proved by drilling in the vicinity of McMurray. Particular attention will be given to a well drilled at Waterways early in 1936 by Industrial Minerals, Limited, when a continuous bed of rock-salt was penetrated with a thickness of 199 feet. As this paper is being presented, a salt plant is being completed and a production well is being drilled at the plant. < is salt deposit is in the vicinity of McMurray, close to the junction of the Clearwater and Athabaska rivets, in township 89, range 9, west of the 4th meridian. McMurray is about 240 miles northeast from Edmonton. As shown on Figure 1, Clearwater river, which rises at Methy portage, in Saskatchewan, enters Athabaska river at McMurray. Some three miles above the mouth of Clearwater river, the Hangingstone enters from the southwest. Waterways, where the latest salt development has taken place, is situated at the end of the Northern Alberta railway, a distance of 304 miles from Edmonton. This railway reaches the bottom of the Clearwater valley at Draper station, about 3 miles east of Waterways and near the mouth of Deep creek. The Draper bituminous sand plant is approximately half a mile east of Draper station. About one mile south of the townsite of McMurray, Horse river enters the Athabaska from the east.

Jan 1, 1937

By Alexandra Kozak, Rodrigo Costa, Bob Fukuhara

"The Jacobina project in Bahia, Brazil commenced operations in 2004 with a design capacity of 4,200 tpd. A project development plan to increase plant capacity to 6,500 tpd will be discussed. The project included an evaluation of the existing circuit and addressed bottlenecks in the crushing, milling, sedimentation, leaching and tailings transport. These circuits and the methodology used to provide higher capacity will be presented.INTRODUCTIONThe Jacobina mine is located in the state of Bahia in northeastern Brazil approximately 330 km northwest of the state capital city of Salvador and 9 km from the town of Jacobina. The Jacobina Mine (Figure 1) is owned by Jacobina Mineração e Comércio, a wholly owned subsidiary of Yamana Gold Inc.The gold mineralization of the Jacobina mine is hosted within quartz pebble conglomerate reefs of the Serra do Córrego Formation which together with the Rio do Ouro Formation forms the Serra do Jacobina mountain chain.The Serra do Jacobina mountains have been mined for gold since the late 17th century. Since the 1970’s, the Jacobina mine has been operated by Anglo American, Williams Resources Inc., Desert Sun Mining Inc. The mine is currently owned by Yamana Gold Inc.In December of 1998, operations at Jacobina were suspended and the property was placed under care and maintenance. Desert Sun Mining Inc. began exploring the property in 2002 and eventually purchased the Jacobina mine in 2003. In 2003, a feasibility study was completed that evaluated the economics of re-developing the mining operations and expanding gold production. In 2004, refurbishment and re-development of the mining operations began and the milling facility throughput capacity was expanded from 1.08 to 1.512 Mtpy (3,000 to 4,200 tpd). The milling operations were commissioned in the 1st quarter of 2005 and commercial production was declared 1 July 2005. In April 2006, Yamana Gold Inc. acquired the Jacobina mine through its acquisition of Desert Sun Mining Inc."

Jan 1, 2008

By Gunnar Nord

Introduction ??Atlas Copco has customers both amongst Miners and Contractors ??We believe that the contractor&apos;s approach to tunnelling is worthstudying ??For a tunnel contractor the incentive is speed as ?30 % of the costs are material related ?70 % of the cost are time related ?A tunnel contractor favours utilizing of the face ?A miner favours utilizing of the gear ??Statement; In mining, a long term average advance rate of more than 10 m / day can be achieved with the excavation techniques availabletoday

May 1, 2009

By H. A. Bilgin, G. G. U. Aldas

"Ground vibration is the natural result of the blasting process. Many empirical formulae and methodologies including analysis of travel path effects have been developed. The scaled distance, which is the most popular approach for the calculation of the attenuation of particle velocity in the ground, has led to significant advances in the prediction of particle velocity when both explosive charge and distance vary. However, this approach does not consider the effect of ground anisotropy and existence of structural geological features on ground vibration. Therefore, in this study, the effects of these rock mass properties on types, amplitudes, and frequencies of ground vibration waves at four surface mines are examined. The results, which were implemented at Kangal coal mine, Bastas quarry and Kíbrís quarry, provided guidance for the extensive study at Orhaneli surface coal mine.As a result of the study, the authors came to the conclusion that vibration amplitudes change depending on the ground on which sensors were deployed and the conditions depending on whether measurements were done near major structural geological features. It was determined that the vibration amplitudes, measured at equal distances from the source but in different directions, change because of the propagation velocity anisotropy. Besides the change of wave type due to the kind of ground at the measurement location, it was determined that vibration anomolies were due to structural features."

Jan 1, 2004

By G. R. Addie

"In February, 1975, the President of Georgia Iron Works Company, Mr. Tom Hagler decided to build a new hydraulic laboratory to water performance test all of the companies' centrifugal slurry pumps.Equipment procurement started in March, 1975, by ordering of a mini computer data acquisition system.Work commenced on the lab in July, 1976, by erection of a Butler Building and the laying down of a 20,000 gallon concrete sump.By late October, a facility compromising two water test loops of 8"" and 18"" pipe diameter was in operation carrying out head quantity and suction performance tests on pumps up to 16"" in size.In August of the following year, an 8"" diameter pipe slurry loop was installed to enable pipe friction and deposition velocity of a slurry to be measured in an 8"" inside diameter pipe.With the encouragement of Reserve Mining in Minnesota and IMCC in Florida, this was followed in March, 1978, by the addition of over 300 feet of 18"" diameter pipe to make up an 18"" diameter pipe slurry system complete with head loss and deposition velocity observation sections.The office and shop areas of the lab were again expanded in April, 1978, to provide further expansion to the test sections and staff facilities."

Jan 1, 1980

By Mehmet Canbazoglu, Kaarlo Haavanlammi, Hannu Laitala

Cobalt is currently a critical metal because of the increasing number of electrical vehicles forecast for production. Copper and zinc are base metals that are used in many everyday applications, including vehicle production. Eti Bakir Co. Mazidagi Phosphate Plants in the Mazidagi district of Mardin, Turkey is a multi-product facility that produces cobalt, copper, and zinc, as well as fertilizers, from the roaster calcine. Roaster off gas is treated in a sulfuric acid plant (SAP) and the acid itself is utilized in fertilizer production. The comminution circuit, roaster, SAP, and calcine leaching process were developed by Outotec and integrated with the fertilizer production process implemented by Eti Bakir A.Ş. This paper describes the hydrometallurgical calcine leaching process used at the plant, with a focus on the oxidative pressure leaching of the cobalt, zinc, and copper-containing calcine. The cold and hot commissioning phases of the pressure leaching autoclave start-up are discussed together with experiences from the ramp-up period. The production processes of the copper cathode and cobalt and zinc-containing salts are also presented together with some of the plant’s operating parameters. INTRODUCTION The ETI Bakir A.S. fertilizer plant, Turkey, is located in Mardin Province near the border with Syria, (Figure 1). The leaching plant project was started in 2012. The purpose of the plant is to separate the valuable metals from the calcine produced by the pyrite roasters, which are used to produce a SO2 containing gas for the new sulfuric acid plant. Fertilizer production requires sulfuric acid, and for this reason a sulfuric acid plant was built; customer already had access to pyrite concentrate, which is used as the roaster feed. During the engineering phase of the roaster and acid plants it was noticed that the roasted calcine contained considerable amounts of valuable metals like cobalt, copper, and zinc. To recover these metals, a calcine leaching process was developed at the Outotec Research Center in Pori, Finland. The main process connections of the Mazidagi site are shown in Figure 2.

Jan 1, 2019

By Amir Zavichi

Today, with the necessity of timely, on-budget and high quality completion of projects, proper use of construction equipment is essential to ensure project success. Construction equipment places a large monetary burden on the project and if not utilized efficiently, it can result in economic losses. Cranes are one of the most important and expensive operational devices on construction sites. They play a central role, and often activities that rely on crane services fall on the project?s critical path. Currently, material-handling scheduling is done by the crane operator or by an on-duty superintendent using his/hers personal judgment, making the process manual and timeconsuming. Thus, developing an optimal schedule, which considers different dynamic constraints in construction job site, may not be possible based on the current practice. This leads to longer operation times and a negative impact on project cost. This paper presents the latest results of an ongoing study, which aims to design and implement a nearreal time crane operation decision support system to be utilized directly by the crane operator or as an aid for the superintendent in scheduling optimal operation services. This system has several advantages such as maximizing the efficiency of crane operations, guaranteeing the best operation possible to reduce the crane?s travel time, reducing crews and equipment idle time, and minimizing the dependence on subjective human judgments.

Aug 1, 2013

By Donald J. Hallbom

"While pipeline hydrotransport is often the most economical way to transport large volumes of mineral concentrate, tailings, or fine ore slurry over long distances, it is in mountainous terrain that pipelining becomes particularly attractive. These areas are often remote, with limited existing infrastructure and few potential users willing to share in the cost of new infrastructure. The rugged terrain makes the construction of railways or roads suitable for haul trucks difficult and expensive. The elevation difference between the mine and the terminal means that the empty trains or haul trucks need to return up-hill, resulting in high fuel costs. With pipelines, this elevation difference may reduce or even eliminate the need for pumping. As a result, numerous pipelines have been built, or are being considered, in mountainous regions around the world including: Tasmania, New Guinea, China, Madagascar, the Rockies of North America, and the Andes of South America. However, there are technical difficulties that need to be overcome in the design and operation of mountain pipelines that do not affect pipelines on more level terrain. This presentation reviews some of these difficulties and methods used to overcome them.INTRODUCTIONPipeline transport of solid-liquid slurry (“hydrotransport”) is an important and cost-effective means of transporting large volumes of solids over long distances, especially from a single supplier to a single user (e.g., a concentrator to a port, a concentrator to a tailings dam, or a coal mine to a power plant). Pipelines are generally found to be more economically attractive than alternate transportation methods (e.g. trucking, rail, conveyors, shipping, or some combination) over the life of a project (Aude et al. 1974).Hydrotransport systems have been built in a variety of terrains, but it is in mountainous regions that pipelining becomes particularly attractive. These regions are often remote and generally do not have existing transportation infrastructure (roads, railways, navigable rivers). There are few potential users (e.g., farmers, other mines, forestry companies, etc.) who may be willing to share in the cost of new infrastructure. The rugged terrain makes the construction and maintenance of railways or all weather roads suitable for large haul trucks difficult and expensive. Mines tend to be higher than the receiving terminal (e.g. a port). This means that the empty trains or haul trucks need to return up-hill, resulting in high fuel costs. With pipelines, this elevation difference may reduce or even eliminate the need for pumping. Pipelines are easier to construct than roads and railroads in these areas for several reasons, including:"

Jan 1, 2006

By N. Shi, T. G. Joseph

The design of dippers for cable shovels has essentially remained unchanged for the last 100 years. In the past 10 years, shovel manufacturers have started taking another look at dipper design, resulting in changes that have borne models from major manufacturers that address some of the wear conditions and material retention problems that dominate maintenance and operational costs. However, with the exception of added lateral curvatures to the front and corners of the dipper, the geometry is essentially unchanged. This paper looks at the criteria that have resulted in the first new cutting dipper design in a century. The design is based on kinematic considerations, reflected in a revolutionary geometry that matches the range of motions of the shovel, designed to minimize wear, impact loading and power required to dig, thus maximizing productivity for a minimum energy requirement. The shape configuration is such that the weight of the dipper is reduced through wall thickness, enabling a larger capacity dipper to be conceived for the same shovel. Benefits are reflected in reduced operational and maintenance costs and increased productivity.

Jan 1, 2006

By Stephen Se

Geological assessment of active mine faces enables ore grade control, geological modelling and exploration planning. Monitoring of the mine advancement at every drill-blast-muck cycle allows for effective production management. However, geological assessments are performed infrequently due to the need to travel to active mine faces, and detailed surveys to map the mine progress are performed at the end of the month. Instant Mine Modeller (iMM) is a portable ruggedized stereo-vision system that creates photo-realistic three-dimensional models of underground mine faces on-site. The 3D models are generated automatically within minutes and can be viewed underground and annotated with geological information. The overall ore percentages of the face are calculated automatically for grade control. Annotated 3D models are located in the mine coordinate system and can be imported into mine management systems. iMM allows for daily monitoring of the mine progress and geology, and for re-visiting the mine virtually as it existed. iMM has been deployed in an underground hard rock mine for 18 months, and it effectively brings the underground work face into mine management offices enabling the right decisions at the right time. iMM has demonstrated benefits to various mine processes including grade control, geological mapping, 3D photo-realistic as-built and production volume.

Oct 1, 2009

By H. D. Stolovitch, M. L. Lavallée

"An engineering system used to analyze and improve the performance of industrial grinding circuits has been adapted into a training program. The systematic approach to the design of training was applied in order to:Determine if training was an appropriate and effective tool for the transfer of this new technology;Define the technical content of the program;Establish program specifications based on learner and context characteristics;Design and test prototypes of the instructional modules; and,Establish a strategy for plant implementation and maintenance of the training program.This paper thus describes how a engineering system is transferred to the workplace through the use of designed instruction.INTRODUCTIONTraining can change human performance in a permanent way. It can improve productivity for the overall benefit of an operation. Organizations can therefore use training as a mean to achieve their specific goals. Training is not the solution to every performance problem. However, in many cases, it can be a very effective way to attain desired performance.The benefits of training are often difficult to assess. However, to remain competitive, organizations must introduce new products and innovative technologies. Often, they can do both most effectively through suitable training interventions.In order for the effort and investment of training to provide optimal results, two points of view should be adopted.• An overall view of the system in which training is to be applied.• A systematic approach to the design of training (Stolovitch and Keeps, 1989)."

Jan 1, 1992