Search Documents

By A. M. Cormie

Introduction The purpose of this paper is to give a brief, general outline of mining practices at Torbrit Silver mine. The geology of the mine is touched on as it is felt that a rough picture of the geology will result in a clearer understanding of the mining methods employed. The main part of the paper deals with mining methods and a section is included on haulage. Development practice is mentioned only briefly. Torbrit Silver Mines, Limited, a subsidiary of Mining Corporation of Canada, is located in the Alice Arm area of northern British Columbia. Access to the mine is by boat to the village of Alice Arm at the head of Alice arm, then truck road, following the course of Kitsault river for 18 miles in a northerly direction to the plant site. The main portal is a further two-thirds of a mile along the course of the river, at approximately the same elevation as the plant, 1,014 feet above sea level. Geology The ore occurs in a massive, irregular-shaped quartz-barite body replacing a folded area in a series of volcanic breccias, tuffs, and flow rocks locally referred to as 'green-stones'. A series of parallel, nearly vertical, fine-grained basic dykes cut across the formation at right angles to the strike of the ore belt over a horizontal distance of 140 feet. The whole of the quartz-barite vein material, which ranges up to several hundred feet wide in places, carries silver values but commercial grade is confined to lenses and shoots where there have been more than usual concentrations of native silver and silver-bearing minerals. The ore-bearing structure plunges at approximately 25 degrees along an axis striking roughly N.65°W.

Jan 1, 1951

By Y. X. Li, L. R. Xiao, S. Gong, S. S. He

Porous copper and porous copper based alloys with controllable pore structure have been manufactured successfully by sintering evaporation process. This process consisted of mixing copper or copper based alloys with NaCl powders, hot pressing and final high-temperature sintering to evaporate the filler material of NaCl powders. NaCl was eliminated completely during vacuum sintering, and strong metallurgical bonding in the walls was achieved. The pores’ structural parameter (pore size, shape, and direction) and porosity can be controlled effectively. These porous copper and porous copper based alloys with controllable pore structure have great potential in many fields. Including heat dissipating materials, heat absorbing materials, chemical catalyst carriers, electromagnetic shielding materials, filtering materials, damping materials, silencing materials, battery electrode materials. INTRODUCTION The development of porous materials began in the 1960s. The research of activated carbon with high specific surface area made porous materials enter the stage of material research (Belyakov et al., 2008; Ferey et al., 2008). With the rapid development of science and technology, porous materials play an important role in material research, and gradually become an indispensable part of the material research field (Wu et al., 2012). The research of porous materials has gradually extended to metal, ceramics, plastics and glass and other fields. It has been successfully applied in many fields, such as functional materials, industrial production, aviation, medical materials, biochemistry and electronics, which fully shows that porous materials have considerable development prospects. Porous silicon, plastic porous materials and glass porous materials are the most widely used in the field of non-metallic porous materials (Capelle et al., 2012). Compared with non-metallic porous materials, metal porous materials have developed rapidly in the late 1980s and become new materials with good mechanical properties and excellent physical properties. Porous metal materials have many advantages, such as large specific surface, small specific gravity, good silencing effect, high stiffness, high electromagnetic shielding performance, good shock absorption performance, etc (Li et al., 1999; Ferey et al., 2008). Among its many applications, metal porous materials can be used as both functional materials and structural materials. In some cases, metal porous materials have dual functions and structures. It is a multi-purpose engineering material with excellent performance. At present, porous copper, porous aluminium and porous nickel are the most concerned materials (Chen et al., 2002; Yang et al., 2017; Liu et al., 2018). The preparation methods of porous copper and copper-based alloys mainly include self-propagating high temperature synthesis (SHS), capsule-free hot isostatic pressing (CF-HIP), spark plasma sintering (SPS) (Kvanin et al., 2008; Takahashi et al., 2008; Zhang et al., 2014). However, these methods can not accurately control pore structure parameters (including pore size, shape, orientation, distribution, etc.). In porous materials, pore structure plays an important role in the overall performance of materials. In order to control pore structure parameters accurately and optimize material performance, it is necessary to explore and develop new preparation technology. In this paper, the sintering evaporation process (SEP) was introduced for the preparation of porous copper and copper-based alloys. The core process of the preparation method is hot pressing and evaporative desalination. Hot pressing can make the pore orientation consistent. Evaporative desalination can ensure the complete removal of NaCl in the form of vapor in a short time, thus eliminating the corrosion of residual NaCl on the matrix metal (Gong et al., 2011).

Jan 1, 2019

By Simon Weixiao Sun

Conventionally, carbon steel has been the primary material for salt mine headframe construction, protected by specialty paint layers to prevent corrosion. These layers require meticulous QA/QC during fabrication and erection, and the top UV protection layer typically loses effectiveness after an average of 10 years, necessitating ongoing maintenance. As headframes age, significant structural repairs are often required. Alternatively, stainless steel can eliminate corrosion concerns, though its high initial cost has limited its use in headframe design. However, when factoring in long-term maintenance costs, a 'maintenance-free' stainless steel headframe can be an attractive option for stakeholders. This paper compares the structural performance and economic considerations of painted carbon steel and stainless steel headframes, including initial capital and long-term maintenance costs. Additionally, it explores a hybrid approach, strategically using carbon steel in low-contamination areas to reduce initial costs and significantly minimize future maintenance efforts.

May 4, 2025

By Fidelis T. Suorineni

HydraboltTM is a Swellex-type dowel support element developed and manufactured by New Concept Mining in South Africa. Like Swellex, the HydraboltTM is a folded tube which can be inserted into a larger diameter hole without pushing. It is then activated by injection of high pressure water which inflates the folded tube to intimate contact with the walls of the borehole at a set pressure, normally 25 MPa. Unlike Swellex however, the set water pressure at the end of the inflation is maintained throughout the life of the dowel. An integral non-return valve makes this possible. The HydraboltTM is being investigated as a possible stress change measuring cell. This paper presents the results of closed form solutions, numerical modeling and laboratory test to date. Preliminary results indicate that the HydraboltTM can be used as a stress change monitoring cell in addition to its conventional role as a rock mass reinforcing element. If successful, the HydraboltTM will supplement microseismic monitoring systems in rockburst-prone ground conditions where they will give quantitative stress change data for both mine design model calibrations and means for proactive safety measures.

Oct 1, 2010

By J. B. Mitchell

Using digital image correlation the evolution of strain and strain at the onset of localisation resulting in a hot tear has been determined for alloys AA6111 and Al¬0.5wt% Cu during solidification. High resolution images of hot tear formation and growth were captured during a constrained bar test that incorporated a glass window above a central hot spot region. The images were analysed using digital image correlation software to measure the evolution of displacement and strain based on tracking the motion of discrete features on the as-cast surface of the sample. Temperature data was also acquired with a thermocouple cast into the sample in close proximity to the hot tear. The interval starting from the point immediately after solidification shrinkage ends (the metal pulls away from the glass) and finishing when the first sign of a crack or hot tear is visible to the eye was used to determine strain data. The minimum strain at which strain localisation occurs was found to be 0.0069 in AA6111 and 0.0021 for A1-0.5%Cu.

Jan 1, 2007

The concept and practices of co-extraction of coal and methane have emerged in recent years to improve coal mining safety and productivity, utilise methane resources, and reduce fugitive emissions in environments that involve multiple coal seams with low gas permeability. The system of co-extraction integrates two previously separate operations of coal extraction and methane drainage. The coal mining operation reduces the coal seam gas pressure and creates strata fractures that enhance gas migration and capture from mine workings and surrounding coal seams. An effective methane drainage operation produces a consistent and quality clean energy product and, at the same time, reduces the methane concentration in underground workings and the methane content and pressure in the adjacent coal seams. This is a significant benefit in preventing gas explosions and outbursts, and promotes a safer and more productive coal mining environment. In addition, the co-extraction with enhanced utilisation of coal mine methane directly leads to a reduction in greenhouse gas emissions. Presented in this paper are key results and outcomes of a major Asia Pacific Partnership project carried out from 2008?2012 by the Commonwealth Scientific and Industrial Research Organisation in collaboration with Huainan Mining Industry (Group) Co. Ltd., to develop and demonstrate advanced technologies at Pansan mine, Huainan, that promote the concept and practices of co-extraction of coal and methane. A comprehensive approach was adopted to assess fundamental strata and coal seam methane conditions during mining, and optimise mining sequences and coal mine methane capture systems. The project has not only demonstrated a practical approach and procedures of advanced co-extraction of coal and methane systems but also delivered significant benefits and outcomes in improved mining safety and efficiency, increased methane capture and utilisation, and reduced fugitive methane emissions at the Pansan mine. The total mine gas drained increased from 25.36 Mm3 in 2007 to 47.0 Mm3 in 2011, and the mine gas utilisation increased from 4.94 Mm3 in 2007 to 21.15 Mm3 in 2011. The improved methane capture resulted in reduced coal and gas outburst risks and methane concentration levels at the mine workings, provided a safe working environment for coal production, boosted the mining efficiency, and eliminated methane related incidents over the last few years at Pansan mine.

Aug 1, 2013

By D. L. Millar

The hydraulic air compressor (HAC) is driven only by water, held up by a dam, to create relatively low head (typically 10-20 metres), such that the developed hydropower is used to cause flow in openings deeper underground. Air is entrained in the water at the inlet to the sub-surface openings (an air to water volume ratio of 1:1 is reported to be optimal) and is compressed as it is carried along by the deepening water flow. At depth, and with lower water velocities arising from larger cross sectional area tunnels, air bubbles separate out of the water flow and are collected in a receiver space above the flowing water. Water, free of air, then passes back up a return shaft (up-pipe) and rejoins the river or stream flow. In principle, an HAC can produce any pressure and flow rate required, given large enough shafts and enough water supply with head sufficient to overcome frictional resistance in the sub-surface tunnels. Practically, as air solubility in water increases with pressure, HAC installations with depths greater than 100 metres may lead to higher rates of compressed air loss, without special separation measures. A modern HAC application for mine refrigeration and cooling is presented.

Aug 1, 2013

By Nelson Hogg

"THE NOR-ACME gold mine is located close to the north shore of Snow Lake, at 54°53' north latitude and 100°03' west longitude. It is about 75 air miles east of Flin Flon, and 36 miles by road from Wekusko at Mile 81 from The Pas on the Hudson Bay Railway.The claims which contain the Nor-Acme orebodies were staked in 1927 by C. R. Parres, who, with his sons, held the ground until 1938 when Nor-Acme Mines Limited was incorporated. In 194 l, on the recommendation of F. Ebbutt (1), this property was optioned by the Howe Sound Exploration Company, Ltd. A program of 50,000 feet of diamond drilling resulted in the outlining of two orebodies containing an estimated 5,000,000 tons with an average grade of 0.15 ounces per ton to a depth of 1,000 feet.A period of inactivity during the war years was followed by the construction of a mining plant capable of treating 2,000 tons of ore per day. Milling started in March 1949, and to the end of 1954 has resulted in the production of 383,793 ounces of gold and 32,906 ounces of silver from 3,331,403 tons of ore.General GeologyThe general geology of the Snow Lake area is described by J. M. Harrison (2), and will not be discussed here except insofar as it affects the Nor-Acme orebodies. The orebodies occur in rocks of Precambrian age that have been classified by Harrison as the Snow group, comprising meta-morphosed sediments interbedded with acid and basic volcanic rocks. The volcanic rocks include pyroclastic types which are unique in the region, a fact which led to their classification in the Snow group rather than the more widespread Missi group that generally occupies the same stratigraphic position above the Amisk group (Figure 1)."

Jan 1, 1949

By M. Ghamgosar, Erarslan N.

Rock cutting includes many unknown parameters which result in different consequences of the different cutting conditions. However, based on the current suggested models for rock cutting, there are some critical parameters that control the fracture initiation and propagation in the rock domain. In general, there are two major cutting tools are used in rock cutting: drag bits and indenters. Different mechanical attacks of cutters result in different fracture models. For example drag bits break the rock parallel to the rock surface, which is called ‘undercutting’ while indenters cut rocks by pressing normal to the rock surface. Both tools cause rock failure by inducing tensile cracks in the rock. However, drag bits induce more tensile cracks compared with the indenters. The full benefits of improvement in rock cutting efficiency will arise from a clear understanding of rock fracture mechanics principles. Therefore, fracture mechanics principles will be applied to the rock cutting as the rock fragmentation process is based on the rock fracturing. The Oscillating Disc Cutting (ODC) has more advantages than drag bits and disc cutters. The forces transmitted back through the cutting head are much lower with ODC. Although ODC attacks rock in much the same way as drag bits, a combination of the oscillating action of the cutter and the undercutting mode produces the lower cutting forces and causes rock fatigue. Fatigue phenomenon in rock has advantages for the rock breaking by applying less effort and energy due to the cyclic loading. The aim of this study is using the Extended Finite Elements Analyses (XEFM) numerical modelling for simulating the ODC cutting with different cyclic loading conditions. An accurate prediction of numerical investigation requires detail laboratory experiments. A series of laboratory tests were performed to obtain the fracture toughness values of our Monsonite rock samples under various cyclic amplitude and frequency values. The numerical results showed different types fatigue damage mechanisms due to the various cyclic loading conditions. Thus, modelling and understanding the crack propagation behaviour depending on different amplitude and frequencies are believed very important for the dynamic rock cutting researches and rock cutting machine manufacturers.

Jan 1, 2015

By J. R. MacDonald

MINING literature contains very few descriptions of operations producing as little as 25 to 30 tons of ore per day. The purpose of this paper is to discuss the gradual development of a mining method for such a small-scale operation at the No. 2 mine of Central Patricia Gold Mines, Limited, and in doing so to review several systems of stoping applicable to narrow ve1ns. MAIN ECONOMIC FACTORS TO BE CONSIDERED (1) Overhead.-The outstanding feature of most mines operating on a single narrow vein is chat of small daily tonnage. The reason for this low output can be readily understood. The strictly limited ore-reserves present a condition unfavourable for a policy of large initial expenditures, with the result that the capacity of the plant provided must be governed by the? amount of ore in sight at the time when mill construction is planned. This is immediately reflected in the cost per ton, there being relatively few tons over which to distributed the more or less static charges, such as hoisting, heating, supervision, administration, pre-production expenses, and other write-offs. (2) Development.-In mining this type of orebody, the main factor contributing to high costs is unquestionably the small tonnage of ore made available by a given amount of development. Thus, for example, from the data tabulated below it can be seen chat, assuming a 12-in. vein and a drifting cost of $9.00 per foot, the development charge for this item alone would be 71 cents per ton. Add to this the charges for raising, cross-cutting, shaft-sinking, and pumping, besides charges arising from development in waste, and the figure will be very considerably higher than 71 cents.

Jan 1, 1941

By Ken J. Brouwer

Stillwater Mining Company commenced construction and development of the East Boulder underground mine in 1998. This new PGM mine is situated adjacent to the East Boulder River approximately 35 miles south of Big Timber, Montana. Project planning and development incorporated detailed collaboration between the regulatory agencies, concerned citizens and mine personnel. A unique ?good neighbour agreement? was established with a local environmental group who have become actively involved in the review of ongoing site development and the implementation of environmental and compliance monitoring. Environmental management systems allow for integrated management of tailings, waste rock and water in order to minimize surface disturbances and to prevent adverse impacts to the East Boulder River. Long-term site development plans contemplate implementation of comingled waste rock and paste tailings. Water management capabilities allow biological treatment of all excess mine water in order to reduce nitrogen loadings prior to land application disposal by means of spray evaporation, snow making and land application. The comprehensive waste and water management plans have also been integrated with staged mine development and interim reclamation requirements.

May 1, 2002

By Norman M. P. Low

"IntroductionIndustrial applications of mica utilize two commercially important varieties of mica: muscovite and phlogopite. Muscovite mica is a potassium mica with a general chemical formula, H2KA1(Si04)3 h, and is sometimes referred to as a potas hsilicate. Phlogopite is a magnesium mica having a general chemical formula, H2KMgSi(Si04)3, and is distinguished from the muscovite mica by its decomposition in sulphuric acid.Canada is one of the major natural mica producers in the world. A large tonnage of the mica powders is at present mined and processed in the Eastern Townships of Quebec. This Canadian mica is of the phlogopite type. A closely related mineral of the mica family which is widely used in the construction industry is vermiculite. It is a dehydrated magnesium-aluminum-iron silicate characterized by a foliated structure. Expanded vermiculite, which is often referred to as exfoliated mica, is used as many types of thermal and acoustic insulation, as loose fill in buildings, as an aggregate in concrete, as an ingredient in plaster and insulating concrete , and in fire-proofing compositions. Natural phlogopite and muscovite mica powders are used extensively as reinforcing agents in organic polymers. They also have a wide range of applications in commerical products. For example, dry-ground mica powders are used in large tonnage as a surface finish in roofing materials and as a bonding agent in wallboard joint cement. Common products such as paint, rubber, plastics and welding rods contain mica. Recent studies have also shown that mica powders can be added to portland cement in the preparation of concrete products, as they could improve the tensile strength of the concrete products. The potential and possible"

Jan 1, 1982

By Dale L. McKinnon, Jean-Pierre Farant

"Dust collectors are used to reduce airborne dust levels generated during crushing at a mining operation and their adequate maintenance is required to ensure effective control of health and safety hazards associated with dusty conditions. Although the pitot traverse technique is commonly employed to balance these dust collectors, the use of an alternative-the equilibrium concentration tracer gas method-is proposed in this paper. This method, which uses sulphur hexafluoride as a tracer gas, can be used to balance airflows in dust collectors and to determine hood collection efficiency accurately and effectively. This technique also reduces some of the errors inherent to pitot tube measurements. IntroductionIndustrial dust collectors are used to reduce dust genera ted by processes like cru shin g, and these must be periodically checked and balanced to ensure continuing effective control of health and safety hazards associated with dusty conditions.To date, the pitot tub e traverse technique has been commonly used to balance air flows in dust collectors. However, this technique is both time -consuming and cumbersome. The equilibrium concentration tracer gas method, described in this paper, is proposed as a viable alternative as it is faster, more reliable, and amenable to automation. The use of tracer gases for such task s is not new. This approach has been used in a variety of mining situations to determine volumetric flow rates in underground openings, leak age through mine stoppings, the effectiveness of face ventilation, pollution migration patterns, mine air recirculation rates, and rock porosity."

Jan 1, 1986

By J. P. Thomson

Magnesium alloys are steadily improving their market share as structural components especially in the transportation sector. Therefore, there is a great deal of interest from the automotive and the metal casting industry to develop viable economic casting processes for magnesium-base alloys. This paper summarizes the preliminary results on the continuing projects within CANMET-MTL on casting processes such as gravity and low-pressure casting in sand molds, permanent molds and lost foam.

Jan 1, 2004

By Ki-Bok Min, Bona Park

"In spite of the applications of DEM models to emulate the elastic modulus, Poisson’s ratio and strengths of isotropic rock in laboratory scale, extensions to anisotropic rock and larger engineering scale still have many challenges to overcome such as robust verification and validation against observed field case. In this study, a discrete element modeling was performed in order to represent a transversely isotropic rock such as shale, and the upscaled model was applied to foundation and borehole problems using PFC2D. The applicability of the upscaled rock mass model was verified by an analytical solution. The DEM modeling of stress redistribution induced by an applied surface line load compares well with Boussinesq’s isotropic solution and anisotropic solution given by Bray. The borehole model with a circular opening under biaxial stress was compared with both isotropic and anisotropic solutions resulting in good agreement. The abilities of DEM model to investigate the micromechanisms accounting for complex macroscopic behaviors and to predict the macroscopic behavior are discussed.The results demonstrate that DEM modeling has the potential to be applied to anisotropic rock mechanics problems on larger engineering scales such as wellbore stability problems especially in shale formations. Furthermore, the effect of anisotropy modeled through this study may be able to explain failure behavior of anisotropic rock encountered frequently in real cases.INTRODUCTIONAnisotropy is prevalent in various types of rocks, especially in shale that contain a set of parallel bedding planes. These weak planes in various forms are sources of large deformation and low shear strength and contribute significantly to the anisotropic behavior of rocks (Amadei, 1996; Cho et al., 2012; Kim et al., 2012). As elastic and strength behavior of anisotropic rock is substantially different from that of isotropic rock, proper consideration of anisotropy is of great importance. There is extensive of experimental evidence showing the anisotropy of shale. Niandou et al. (Niandou et al., 1997) analyzed the plastic deformation and failure mechanisms of Tournemire shale were highly dependent on the orientation of bedding planes. Cho et al. (Cho et al., 2012) presented various deformations and strengths of Boryeong shale obtained from laboratory experiments. Fjaer and Nes (Fjaer and Nes, 2013) performed uniaxial and triaxial compressive strength tests using Mancos shale, and they observed that the shear sliding along the planes of weakness before the occurrence of a major failure can reduce the strength of anisotropic rock. The recent research has demonstrated that the anisotropy of rock is an important consideration in rock engineering."

Jan 1, 2015

By J. Dubinski

Passive tomographic imaging is a technique that can be used for assessing seismic hazard in mines with high seismic activity induced by mining. The basic idea behind such an interpretation is the assumption that there is a relationship between high values of seismic velocity and high values of stresses in the rock mass. This relationship was confirmed both in laboratory an in situ measurements and constitutes the basis for rock-burst and seismic hazard evaluation. In the paper seismic tomographic images of seismic P wave velocity and seismic P wave velocity gradient have been presented to determine rock-burst hazard and locate high seismic activity zones in the area of coal panel 306 in Zabrze Bielszowice mine. The zones of high values of P-wave seismic velocity gradient have been found to correlate with the distribution of high energetic seismic events. Passive tomographic images were obtained using modern bent ray tracing tomography algorithm with regularization. Recent study give rise to observation that not only high values of P-wave seismic velocity is important in seismic hazard assessment as many strong seismic events are located in the areas of high values of velocity gradient. This recent observation permits to increase quality of passive tomographic imaging for detection of seismogenic zones and is presented in the paper. The advantage of passive tomography comparing to active tomography is that sources of seismic waves are generated by rock mass itself and costly controlled explosions are not necessary. Another practical limitation of active tomography is the size of study area which usually do not exceed 200 m by 200 m. This restriction does not appear in passive tomography where area of study is usually 2000 m by 2000 m and the tomographic images delineate velocity structure in locations where mining induced seismicity take place. Passive tomography method utilized in analysis of rock mass state in underground mines encounter some difficulties concerned with the numerical stability of optimization algorithms. In the presented approach to passive tomography problem numerical stability is obtained by special regularization method and by application of very stable numerical seismic ray-tracing algorithm.

Aug 1, 2013

By Richard Cyr, Peter Larsen, William Quesnel

"The need to continually improve efficiency and lower costs in mining operations is of paramount importance to all concerned in the industry. Mining operations are constantly testing new methods and equipment in order to lower costs and improve productivity. Equipment suppliers strive to fulfill the demands of the mines through improved design and innovative ideas for productivity increases. In some cases, however, an increase in productivity does not require new equipment design, but rather the application of an existing mining method into different operating parameters. Such is the case in applying longhole methods to narrow vein ore deposits.Bulk mining methods have long been recognized as efficient, low-cost alternatives in narrow vein operations. Typically, shrinkage and some cut-and-fill methods are employed. The shortfall of these methods is the tendency to be labour intensive. The demand for miners skilled in these methods far outweighs their availability. Consequently, labour-efficient methods have to be employed to fill the void. The application of longhole drilling techniques to narrow vein deposits is one such method.IntroductionPercussion longhole drilling evolved in Canada in the early 1940s. Prior to percussion drilling, blast holes were drilled using diamond drill equipment. Jack Gardner, of Gardner Steel, began testing with carbide percussion bits and extension drill steel in applications where diamond drills had been previously employed. Percussion drilling equipment proved to be considerably more productive and cost-efficient. The experiment eventually led to the replacement of diamond drills in this application.Over the years, the percussion methods were improved, with particular emphasis on the equipment used. Rifle bar rotation machines evolved to independent rotation. Bar and arm set ups evolved into self-contained mobile drill carriers that increased productivity while reducing the physical labour. The introduction of hydraulics further improved efficiency and production figures. Today, it is not uncommon to see fully computerized jumbos in production longhole drilling applications. These machines represent the ""state-of-the-art"" in longhole drilling equipment.Production longhole drilling is considered to be one of the most efficient bulk mining methods in use today. Production statistics normally exhibit low-cost, efficient ore extraction. As a rule, longhole (blasthole) methods are associated with substantial ore deposits. These methods have exhibited high production figures and low mining costs.Over the past decade, long hole methods have been applied to several narrow vein deposits. These applications have proven that, given the right parameters, longhole methods will produce the same advantages in narrow vein deposits as are seen in more conventional applications."

Jan 1, 1990

By J. Béland

"Three stages, each characterized by a particular sedimentation, magmatism, mineralization and deformation, are recognized in the geological history of Gaspe. The first stage led to the formation of the Taconian orogen, the second to that of the Acadian orogen and the third stage to the accumulation of a post-orogenic cover. The Taconian orogen includes volcanic and detrital rocks of Late Precambrian or Cambrian and Lower to Middle Ordovician ages in which ultrabasic intrusions have been emplaced. Folding is severe. Mineralization is of the Cr-Ni-Cu type, related to the igneous facies.The rocks constituting the Acadian orogen include two distinctive sequences corresponding to two successive sub-stages. The second substage began in Early Devonian time with the first pulses of the Acadian orogeny. The rocks of the first substage grade southward from a nearly platformal sequence to an assemblage implying less stability and spotty volcanism. The second substage was one of synorogenic deposition of elastic rocks, first in a marine environment and later under terrestrial conditions. Granitic intrusions, surrounded by aureoles of skarn and hornfels in which Cu-Pb-Zn mineralization is found, accompanied the Acadian deformation. The second-stage"

Jan 1, 1969

By J. Spross

"The Key Lake mill has operated since the fall of 1983. The ore from both Key Lake open pits will be depleted by 1997. It is planned to use this mill, located about 60 km southwest of McArthur, to process the McArthur River ore.While the geological data collected so far on the McArthur deposit are encouraging, more information of the deposit is needed before any detailed mine planning can begin.The surface drilling program identified the orebody and provided information on the geomechanical and hydrological properties of the overlying sandstone. It was proposed to conduct an underground exploration program to further delineate the orebody. This was air proved following a public hearing and review process. This program involves the sinking of a 630 metre deep shaft and the driving of one or two drifts along a portion of the orebody. From these drifts, exploration drilling every 10 m to 15 m through the orebody will provide the information required for the preparation of a feasibility study and an Environmental Impact Statement (EIS)."

Jan 1, 1994

By N. Chow, W. McCombe, G. Remple, J. Nikkari, L. Nightingale-Mercer

Orano Canada Inc. (Orano) operates the McClean Lake mill in northern Saskatchewan, processing high concentration uranium ore, delivered in slurry form, from the Cameco operated Cigar Lake mine. This slurry is ultimately processed into the purified uranium oxide product known as calcined yellowcake. During the calcining process, sulphate (SO42-) entrained in the yellowcake undergoes thermal decomposition into sulphur dioxide (SO2). SO2 is a colourless gas that poses health and safety risks. Since 2016, an anhydrous ammonia dosing system was successfully added to the existing Venturi particulate scrubber system to provide efficient removal of SO2 from the calciner off-gas. Within the pH controlled scrubber solution, SO2 exists in a pH dependent equilibrium with sulphite/bisulphite (SO32-/ HSO3-). The presence of a significant fraction of reduced sulphite and bisulphite in mill solutions presents a hazard in downstream circuits. Should these solutions drop in pH, either through natural oxidation or inadvertent mixing with low pH solutions, the solution equilibrium will shift from SO32-/HSO3- in favour of SO2, resulting in the evolution of SO2 gas from any liquid surfaces. In 2018, Hatch Ltd. (Hatch) and Orano implemented a design change in the calciner scrubber system. Blowdown from this system is now treated in an oxidation pre-step utilizing hydrogen peroxide (H2O2) and anhydrous ammonia (NH3) for pH control, in order to convert the residual sulphite/bisulphite present in solution to stable ammonium sulphate product. This paper will detail some of the challenges and actions undertaken to minimize SO2 risk, culminating in the recent introduction of a novel system designed to oxidize sulphite/bisulphite and prevent mobilization from the calciner scrubber solution into other mill areas where there is the potential for acidification and SO2 release.

Jan 1, 2020