Search Documents

By F. Hassani, E. Aflaki, M. Nokken, M. Kermani

"This paper presents and compares the physical properties of Gelfill and cemented hydraulic fill (CHF) obtained by lab experiments. Gelfill consists of tailings, different binders such as Portland cement, fly ash and blast furnace slag and an alkali activator such as sodium silicate. The CHF and Gelfill samples with various mixture designs were cast and cured for 28 days. The influence of sodium silicate concentration, pulp density and mixing time on the mechanical properties of samples were evaluated using the uniaxial strength test. Mercury intrusion porosimetery (MIP) was used to analyse the microstructure of CHF and Gelfill samples.This study concludes that: (i) The mechanical properties of CHF can be improved by the addition of appropriate amount of sodium silicate. (ii) The rate of strength acquisition in Gelfill samples is faster than CHF samples over 28 days of curing period. (iii) Mixing time strongly influences the mechanical properties of Gelfill samples but did not have any effect on CHF samples. (iv) The MIP analyses indicate that the pore size distribution and total porosity of Gelfill and CHF were different, and this did contribute to higher strength development of the Gelfill samples. INTRODUCTIONThe increased depths of mines in the Canadian Shield and the high stress associated with these depths favour a new method of mine backfill that can both meet strength requirements and help mine productivity. The mine backfill mainly consists of tailings, water and binder materials, the latter being most expensive. Gelfill is a new mine backfill material whose binder usually consists of alkali activators such as sodium silicate and other cementitious materials such as blast furnace slag and normal Portland cement. Although sodium silicate has been used in concrete manufacture, the use of this material in mine backfill is relatively new (Doucet, 2007, Razavi, 2007). Until very recently there have been only a few isolated publications, mostly out of McGill University, regarding mine Gelfill (Razavi, 2007 and Kermani et al., 2009 and 2010). These papers have investigated some of the basic mechanical properties and mechanical behaviour of Gelfill. However, the physical performance of Gelfill in various conditions has yet to be understood. Therefore, the main objective of this study was to investigate the influence of mixing time and sodium silicate concentration on the mechanical performance of Gelfill and CHF through a series of experiments. Moreover, the microstructure of the Gelfill and CHF samples was studied."

Jan 1, 2015

By Stanley Davidson

"The ore deposit mined by Falconbridge Nickel Mines, Limited, is one of the numerous nickel-copper sulphide bodies marginal to the large oystershaped mass of differentiated norite in the Sudbury district, famous as the world's most important nickel producing field. The unique character of the ore deposits of the district has resulted in its intensive geological study over a period of more than 50 years. The results of these studies have given rise to a voluminous geological literature and to a great deal of controversy as to the genesis of the ores. This description of the structural geology at the Falconbridge mine is presented in the hope that it may form a small part of the chain of evidence leading to a reasonably satisfactory explanation of the ore genesis.The mine, named after Falconbridge township in which the deposit occurs, lies along the southeast margin of the norite mass, which, however, is h::re concealed beneath a deep mantle of glacial sands and gravels averaging over 100 feet in thickness. As a consequence, the deposit was not discovered by the early prospectors, and it was not until 1916-17 that E. J. Longyear, of Minneapolis, located the ore by drilling(ll). The discovery was foreshadowed in 1899 by the work of Thomas A. Edison, who found indications of the deposit by what is believed to have been a combination of magnetic and electrical geophysical surveys. He sank a prospect shaft over what has to date proved to be the largest and richest ore section in the mine. A wet quicksand layer at the rock surface proved impenetrable, however, and the 'Edison' shaft never reached bed-rock.The Falconbridge property was acquired by the Lindsley interests in 1928, and ore output, since its inception in 1929, has gradually risen from a modest beginning to the present 2,000 tons and more daily. Total production in this period is 7,500,000 tons of ore averaging 1.72 per cent nickel and 0.89 per cent copper, together with a small but valuable content of precious metals, principally of the platinum group."

Jan 1, 1954

By Michael J. Sapko, Ellsworth R. Spencer, Frank J. Perzak

"The fire resistance of several mine conveyor belts is evaluated using a new belt-flammability apparatus developed by the U.S. Bureau of Mines. The test apparatus, experimental details and a calculated flammability index (FI) are described.The FI values are useful for ranking the fir e resistance of mine conveyor belts. Values are determined using parameters readily measured with thermocouples, high-temperature flow probes and a methane-oxygen torch, all of which are components of the Bureau's new test apparatus. The FI varies directly with the flame-spread rate and the rate of heat release during burning and varies inversely with the critical (minimum) ignitor energy output.The fire-resistance ranking of nine different belt types using this moderately scaled apparatus is compared with available full-scale data on belt fires. This comparison shows that the ranking based on the FI is consistent with the full-scale data.IntroductionFull-scale fire hazard evaluations of mine conveyor belts are not easily related to the properties usually measured in small-scale flammability tests. The inadequacy of small-scale belt fire tests has been demonstrated in works by Mitchell, Warner and Reinke.Mitchell and Warner showed that certain neoprene (NP) and polyvinyl chloride (PVC) belts, which had been approved by the Code of Federal Regulations 30 CFR 18.65, were nevertheless capable of propagating flame over their entire length when full-scale fire conditions were simulated. Comparable results were also observed by Reinke at the Tremonia experimental mine in Dortmund, West Germany, where all belts burned in full-scale tests even though they passed the small-scale tests. Only by reducing the severity of the full-scale test could these fire-resistant belts be grouped on a pass-fail basis."

Jan 1, 1982

By E. Ozberk, N. Gibson, W. G. Davenport

"In the 1950s, Canada produced more than ninety-five percent of the non-communist world's nickel and achieved dominance in terms of production, technology and pricing policies.Over the past thirty years there have been dramatic changes in the nickel industry to the extent that Canadian production is now less than thirty per cent of the total.In this document we have presented statistics relevant to this transformation and reviewed the technology, particularly with regards to energy and environmental considerations.Under the new market conditions nickel producers are likely to face more difficult competition than they have encountered in the past.The economic scene and measured nickel reserves dictate that for the purpose of increasing production, new nickel smelters will not be built in Canada in the foreseeable future. However, in order to reduce sulphur dioxide emissions, Canadian nickel smelters will possibly go through some modifications or rebuilding.IntroductionThis paper presents a review of the Canadian nickel industry in relation to the world nickel industry. Major changes are described which have occurred in the characteristics of the nickel market over the last thirty years. The pre sent status of the nickel market with respect to Forecasting future trends is reviewed and attempts are made to predict what further changes will take place in the next two decades. Comparisons are made of the economics of producing nickel from sulphide ores and oxide ores and the advantages and disadvantages the Canadian nickel producers face.A brief critique of the existing and emerging nickel production technologies in Canada and the world is carried out and attempts are mad e to predict the changes which may take place in the foreseeable future."

Jan 1, 1983

By J. Chlan

"Dryer DescriptionProctor and Schwartz Continuous Conveyor DryerThe Proctor and Schwartz Continuous Conveyor Dryer has been in operation since July 1958, and comprises six unit• - an 8• wide single conveyor with roller extruder, insulated housing, type 304 stainless steel circulating and exhaust fall system, steam heating coils, temperature controls and discharge crusher rolls. Entire dryer dimensions are 52’ x 12'0""weighing 53,000 lbs,Extruder rolls - setting is 1/8"" (Drive 3 HP 1800 RPM) clearance off the extruder screen.Conveyor - consists of 151 interlocking pans, measuring 8"" x 8' (2 HP 1200 RPM) One Exhaust Fan (5HP - 900 RPM)Steam Coils -- l"" steel pipe - with steel fins -- each coil measures 16' 2’’- 64 coils in the No, 1 Compartment- 64 coils in the No, 2 CompartmentDryer OperationThe yellowcake slurry at 28% solids is pumped to an 81 x 8' Peterson Filter. The filter media presently being used is a Neotex 4372 blanket, being 100% staple fibre nylon, 12 oz per square yard with air porosity of 9 CFM's. The cake discharge at 45 - 50% moisture falls into the roller extruder. Extrusions are formed by forcing the material by rolls through a perforated plate moving back and forth and depositing the spaghetti-like extrusion on onto the dryer-conveyor.The conveyor now carries the extruded material through the heating chamber•, The feed end of the dryer will be referred to as No. 1 Compartment, with temperature control set at 280""F. The circulating fans take the hot air off the coils and circulate the heated air through the perforated openings in the dryer conveyor pane, After passing through the set of steam coils and circulating fan in No, 1 Compartment, the material then goes through No, 2 Compartment where the temperature is set at 305'F, Final material then discharges through a set of crusher rolls set at ~"". Moisture of final dried product runs at less than 2%.The dryer conveyor load is usually run to a 3"" - 4"" depth load. Conveyor speed at approximately 90 minutes for load to pass through. Load onto the conveyor is controlled by boot level and speed of the 8' x 8' filter. The dryer steam coils are water-washed twice a month."

Jan 1, 1972

By J. A. Finch, A. M. Elmahdy

Blending frothers is becoming common in flotation practice apparently enhancing performance. However, there have been no studies to understand the blend mechanism. In this paper, the effect of two frother blends ofF150 (polyglycol) with MIBC or pentanol (both alcohols) on bubble size, gas holdup and froth height is reported. The blends focused on a small addition of the polyglycol to the alcohols as base frother. The tests showed that the bubble size at blend concentration below the critical coalescence concentration (CCC) of the base frother was decreased but was significantly larger above the base CCC. Froth build-up showed a strong synergistic effect.

Jan 1, 2009

By J. K. Atherton

If the metals sector is to contribute successfully to sustainable consumption we must adopt principles and practices which address the entire life cycle of the materials we produce. Progress must be founded on a sense of shared responsibility for the resources we utilize and the materials we create - it is this integrated approach which lies at the heart of materials stewardship. Materials stewardship means mining and metals companies producing materials in a responsible manner and then working with others, beyond their site, to ensure that the downstream material flows and applications are managed properly to create maximum societal value. In September 2006 ICMM published 'Maximizing Value: Guidance on implementing materials stewardship in the minerals and metals value chain'. This document takes a practical view presenting structured guidance as well as good practice case studies. In the publication, materials stewardship is described in terms of the range of activities that can be undertaken to ensure that all parties work collectively toward the responsible use of metal and mineral resources. This paper introduces the materials stewardship concept as set out in `Maximizing Value' and describes the business case for implementation as well as the ICMM framework for promoting materials stewardship.

Jan 1, 2007

By Laura Kelsey

Contaminant Robust In Situ Water Extractor CRIWE Nafion-based water clean-up Extract purified water from natural extraterrestrial sources In situ water processing for downstream electrolysis Chemically resistant to process contaminants such as acid

May 1, 2013

By W. L. Goodwin

Twenty-five years ago mining engineering in Canada was not a profession. To-day the members of the mining fraternity can fairly claim for 10themselves the professional status. If their pretension is not fully warranted by fact it is not for lack of any technical attainment or service to the public but by reason merely of their neglect to cultivate the cohesion and consciousness that are the outward and visible signs of a professional body. This paper is an attempt, first to sketch briefly the course of the events during the past thirty-five years that have resulted in organizing the mining industry of this country in its present form; then to notice the principal features of the professional organization of this day; and finally to point out that an important part of the work of the mining engineer remains in the state of chaos that characterized the whole of it three or four decades ago, and to suggest a remedy. Thirty years ago there came a great wave of interest in mining in Canada, based principally upon the discovery of gold-quartz and gold-copper throughout wide areas in Nova Scotia, Ontario and British Columbia.

Jan 1, 1926

By John H. Low

Introduction Despite the fact that the .association of magnetite with chrysotile asbestos in the parent producing area of the world, the Thetford Mines - Black Lake area, has been recognized since the ores of that region were first known, magnetic methods were not extensively employed in exploration for asbestos until about the beginning of 1949. Since then, large areas of Ontario, Quebec, and the eastern United States have been prospected both by aeromagnetic and conventional ground magnetic methods. Prior to 1949, a limited amount of magnetic work had been done, notably that of A.H. Miller (1, pp. 184-186), which was carried out in conjunction with the geological survey of the Thetford area by H. C. Cooke (2) in the years of 1930 to 1932. At that time, Miller pointed out that the occurrence of asbestos is associated with very large magnetic 'anomalies' and that, within the Pennington dyke, an area of asbestos- bearing peridotite could be distinguished, by the anomalies, from adjacent areas of non-asbestos ?-bearing peridotite. Since he .also observed large anomalies in what were believed to be ?barren areas, Miller concluded, however, that the magnetometer could hardly be of much or any value in the direct location of asbestos War .and post-war demands on known reserves of asbestos ore, however, stimulated the search for new deposits, and an economical and rapid method of directing speculative drilling was most desirable.

Jan 1, 1951

By L. A. Homeniuk, R. Bonnar

"The Fond-du-Lac uranium deposit is located on the northern rim of the Athabasca Basin. The uranium mineralization is, for the most part, confined to the Athabasca Group, which is underlain by pre-Helikian metamorphic rocks of the Western Craton.The deposit is characterized by a remarkable train of mineralized glacial erratics which led to the original discovery. The mineralization is present as a ""high-grade"" core and a diffuse ""low-grade"" aureole. The ""high-grade"" core occurs as a stockwork of steeply dipping pitchblende veins which strike N 50°E. Hematite, siderite and secondary silicate are also abundant. The ""low-grade"" aureole contains uraniferous goethite, argillaceous material and rare carbon buttons. Recent alteration to coffinite has taken place along the margins of pre-existing ore minerals.The ""high-grade"" core is 390 m long and 10 to 40 m wide, and is surrounded by an irregularly shaped zone of ""low-grade"" mineralization with a similar length and a width of up to 350 m.Comparing the Fond-du-Lac deposit to other unconformity-type deposits, several important differences can be noted:1. Ninety per cent of the ore is above the unconformity, in the Athabasca sandstone.2. The deposit is not associated with underlying graphitic rocks or a major structure.3. The clay-rich alteration zone is not extensive around the Fond-du-Lac deposit.Although there are differences with other Athabasca unconformity-type deposits, the high-grade portion below the unconformity suggests a common origin.The ore deposit is postulated to have been formed from uranium-bearing solutions which entered the stockwork of fractures. Following the reduction in part of these solutions by pre-existing carbonaceous matter and pyrite and/or chemical reaction with pre-existing hematite, deposition continued as a result of decreasing temperature and pressure. Subsequently, minor supergene redistribution of the uranium has taken place."

Jan 1, 1982

By L. A. Homeniuk, R. Bonnar

"The Fond-du-Lac uranium deposit is located on the northern rim of the Athabasca Basin. The uranium mineralization is, for the most part, confined to the Athabasca Group, which is underlain by pre-Helikian metamorphic rocks of the Western Craton.The deposit is characterized by a remarkable train of mineralized glacial erratics which led to the original discovery. The mineralization is present as a ""high-grade"" core and a diffuse ""low-grade"" aureole. The ""high-grade"" core occurs as a stockwork of steeply dipping pitchblende veins which strike N 50°E. Hematite, siderite and secondary silicate are also abundant. The ""low-grade"" aureole contains uraniferous goethite, argillaceous material and rare carbon buttons. Recent alteration to coffinite has taken place along the margins of pre-existing ore minerals.The ""high-grade"" core is 390 m long and 10 to 40 m wide, and is surrounded by an irregularly shaped zone of ""low-grade"" mineralization with a similar length and a width of up to 350 m.Comparing the Fond-du-Lac deposit to other unconformity-type deposits, several important differences can be noted:1. Ninety per cent of the ore is above the unconformity, in the Athabasca sandstone.2. The deposit is not associated with underlying graphitic rocks or a major structure.3. The clay-rich alteration zone is not extensive around the Fond-du-Lac deposit.Although there are differences with other Athabasca unconformity-type deposits, the high-grade portion below the unconformity suggests a common origin.The ore deposit is postulated to have been formed from uranium-bearing solutions which entered the stockwork of fractures. Following the reduction in part of these solutions by pre-existing carbonaceous matter and pyrite and/or chemical reaction with pre-existing hematite, deposition continued as a result of decreasing temperature and pressure. Subsequently, minor supergene redistribution of the uranium has taken place."

Jan 1, 1982

By Gerhard Melcher, Hermann Hilbrans, Michael Gamroth

"IntroductionSeveral new smelting processes have been proposed and developed during the last 20 years. This has been true, in particular, for copper smelting technology. The important impulses for the advances in this field have been the recent demands regarding the environmental protection, energy saving and improved utilization of the metals contents of deposits, in particular that of complex raw materials.The methods developed more recently for pursuing these objectives have been outlined in several papers. In some of them the advantages and drawbacks of certain developments have been stressed. These documents are of great importance for assessing the different processes. The following paper tries to explain some details of the cyclone smelting process taking into consideration a few of these well-known presentations. The effectiveness of operation of the cyclone smelting process indicates that this process presents a significant achievement when compared with other conventional methods.The application of the CONTOP smelting cyclone range s beyond the field of copper metallurgy or the smelting of sulphide concentrates with the aid of oxygen. The research work carried out in the pilot plant of KHD Humboldt Wedag AG in Cologne-Porz also includes the recovery of the metal contents of intermediate products and processing of smelter residues which have to be converted in a disposable stat e, free of environmental pollution. This paper explains a few examples in this regard."

Jan 1, 1987

By Torsten Zeller

Due to the increasing worldwide demand for raw materials and the resulting rise in commodity prices more expensive processing that is able to utilize complex ores becomes economically viable. This and increasing ecological awareness is why the interest in recycling and urban mining is steadily growing in Germany. In addition to that; landfills do also contain elements, which were not targeted over the period, when they were being accumulated. Examples are rare earths, indium, gallium, cadmium, arsenic, selenium and tellurium. Also copper, zinc and lead, the target components of ancient mining, can be obtained due to more effective processing and smelting technologies. Funding by the German Federal Ministry for Education and Research, entitled "r³ ? Strategic Metals and Minerals ? Innovative Technologies for Resource Efficiency" also indicates the high level of strategic interest. It is against this background that the research project "Exploitation of the Raw Material Potential of Mining and Metallurgical Tips in Respect of Sustainability as Exemplified in the West Harz Mountains (ROBEHA)" has been implemented. A major concern of this project is the possible transfer of results to landfills in other areas. Therefore the development of an expert system based on the innovative processing methods and a method manual for urban mining are the central components of the investigation. This will provide an important contribution to the cost optimization of ensuing urban mining projects. To ensure the success of landfill mining projects it is necessary to record the composition and quality of the deposits accurately. Also the environmental impact caused by landfill mining and changes in the natural and cultural landscape will be considered in a multicriteria evaluation method. Depending on their origin the tips are divided into the categories mining, processing, and smelting. The content of a landfill and thus the economic potential in terms of urban mining is dependent on the type and composition of the deposits (host rock, gangue, and ore mineral), the available processing and smelting technology, and the target components at the time of mining. Zinc, for example, was not been processed until the 19th century, when it gained attention as being material of economic importance. After such knowledge about a landfill is obtained the decision for further investigations can be made. For a total of 158 landfills in the Harz Mountains, both the volume and the approximate contents of copper, zinc, and lead has been estimated for the different types of tips within past research projects. Based on the prices of the London Metal Exchange (LME) and a euro/dollar exchange rate of 0.76 (as of 03/05/2012) and assuming a minimum density of ? ? 1.5 t/m³ a average value of 1.6 billion ? in copper, zinc, and lead can be obtained. Although only these three metals are considered in this first estimate, it demonstrates the potential of landfill mining and the need for further research. KEYWORDS Urban Mining,

Aug 1, 2013

Safety Leadership The management and leadership of a mining operation is a challenge at all times. The pressure to make production, safety, and environmental goals is intense. At some point mining cycles will put every operator into periods of time where economic issues seem to over-ride all other concerns. This is when leadership is most needed.

May 1, 2009

By E. G. Gaylord

THE material improvements which have been made in the practice of exploiting oil and gas reservoirs in the United States during recent years may be attributed largely to: (1) The necessity for drilling deeper wells at costs not much greater than was formerly expended on shallower wells. (2) The necessity for producing oil at a lower cost per barrel. (3) A growing recognition of the importance of the nature of production practice upon ultimate yield of oil and gas. The first two of these factors result, to a large extent, from the fact that a greater proportion of new development has been deeper development, and these wells have been drilled in the face of progressively lower per well allowables. In California, for instance, maximum allowables have declined from 400 barrels per day in March, 1938, to 156 barrels per day in September, 1940, and during this same period some 125 wells were drilled to the deeper 10,000-foot producing horizons discovered during this time. The third item listed above results from our increasing knowledge of the basic factors which influence the amount of recovery we may expect from reservoirs. In addition to the longer-range planning now being undertaken by the more prudent operators, State proration and conservation laws have focused attention upon the importance of methods conducive to obtaining progressively greater quantities of the hydrocarbons in place. In a paper of this length it will be possible to discuss only a few of the recent advances. An effort has been made to select the more important of these and to indicate, where possible, the factors which have made these advances possible.

Jan 1, 1941

By Tibor Horvath

Dust abatement is possible on bulk materials, whether conveyed or stockpiled. Minimum (ppm) quantities of chemical additives can efficiently and rapidly control dust of conveyed substrates with no effect on floatation chemistry. Top coating of large surface areas can control surface dust and wind erosion. Environmental and toxicity impact must be considered in any treatment, especially on areas with percolation runoff, leachates, or limited containment. The most effective dust control is preventing release of substrate fines rather than trapping and removing air borne dust. Techniques to prevent release of fines from conveyed substrates will be discussed. Dust control dynamics are a very complex combination of solid phase physical and chemical interactions between the substrate and the fines. ?Smart Technology? products permit dust abatement of stockpiled substrates and tailing fields with no environmental impact. Using ?Smart Technology?, the dust abatement products remain active and can re-seal damaged areas. Efficient, low environmental and toxicity impact, dust control will be demonstrated through case studies where these principals have been applied.

Oct 1, 2010

By V. Fiedler, H. Lachmund, R. Bruckhaus

"After producing some 50 million tonnes of crude steel the two BOF vessels at Dillinger Hüitte steel plant had to be replaced in 2000/01 due to large deformations. The new vessel design was optimised after a number of theoretical evaluations.Refractory investigations were carried out as well as temperature measurements of the shell to provide a basis for selecting a suitable steel grade. This was found in a DH-GTS development - P420M HT - with high strength at elevated temperatures and excellent weldability and made it also possible to build the vessel without any cooling system.After putting the first vessel into operation the metallurgical results showed no remarkable improvement compared to the old vessel, and were therefore not satisfying. With the help of cold model investigations the arrangement of the tuyeres was modified to improve the flow conditions and the interactions between oxygen jet and the heterogeneous plume of the bottom stirring gas. Further optimisations were obtained by a variation of lance tips and a newly developed lime addition model."

Jan 1, 2004

By C. O. Staples, J. G. Morrow

The application of cationic flotation to the upgrading of magnetic concentrates was investigated in the laboratory by both batch and continuous test procedures. It was found that the collection of coarse gangue particles with amine, heretofore considered a serious obstacle to this particular application of cationic flotation, is greatly enhanced by a drastic reduction in what might otherwise be considered normal impeller speed. Gangue flotation is in-dependent of variations in the rate of aeration. The collector and Crother additions and the impeller speed which favour the formation of a matte froth yield optimum results.

Jan 1, 1966

By S. Esmaeili

The yield strength model developed by Esmaeili, Lloyd and Poole [1] has been adapted to model isothermal aging in Cu-containing AA6xxx alloys, with (a) a moderate and (b) a very low Cu content in the solution-treated, as-quenched, condition, Isothermal calorimetry has been used to analyze the kinetics of precipitation in these alloys, While the kinetic parameters for the low Cu alloy has been derived from the present experiments, the previously determined kinetic parameters for the high Cu alloy AA6111 has been used to model the precipitation kinetics in the moderate Cu alloy. The age hardening responses of both alloys have been well predicted by the model.

Jan 1, 2005