Search Documents

By D. Kong, A. Klyashtorin, L. McGilp, I. Wilson

This work reports on applying iron oxide coated sands media in an experimental permeable reactive barrier to remove uranium species from uranium containing water. A field experiment was conducted at the legacy Gunnar uranium mine & mill site that was abandoned in the 1960s with limited to no decommissioning. The flooded Gunnar mine pit presently contains about 3.2 million m3 of water contaminated by dissolved U (1.2 mg/l), Ra-226 (0.4 Bq/l), and minor concentrations of other contaminants (As, Se, etc.). The water is seeping over the pit rim into Lake Athabasca posing environmental and health concerns. Iron oxide coated sands can be used to immobilize uranium species through an adsorption process. Methods for preparation of hydrous ferric oxide sorbents and their supported forms onto silica sands are described. Fourier transform infrared spectroscopy (FTIR), and powder X-ray diffraction (pXRD) were used to characterize the physical-chemical properties of the sorbent. The monolayer uranium uptake capacity (Qm) was estimated through the Langmuir adsorption isotherm. Adsorption kinetic experiments were performed in a lab environment before moving to a field trial. Based on these lab results and the input on field-scale appropriate geometries, a pilot permeable reactive barrier was fabricated and a field test conducted near the Gunnar pit in June 2019. This pilot test provided technical data and information needed for designing a full-scale permeable barrier based on the iron oxide coated sands, which may be applied for in-situ water treatment at Gunnar and other legacy uranium sites.

Jan 1, 2020

By C. D. Anderson, C. G. Anderson, P. R. Taylor

"Rare Earths have become critical for our energy and materials driven society. While primary production must ramp up to fill growing demands, the recycle of these strategic elements must also be initiated. This paper will outline the potentials of and metallurgical technologies employed for Rare Earths recycle from various secondary sources.INTRODUCTIONWhen investigating the recovery of rare earths from secondary sources it is necessary to understand the nature of the sources to be processed. As of 2009, the USGS reports the distribution of rare earths by end use, in decreasing order, was: chemical catalysts 22%, metallurgical applications and alloys 21%, petroleum refining catalysts 14%, automotive catalytic converters 13%, glass polishing and ceramics 9%, rare earth phosphors for computer monitors, lighting, televisions 8%, permanent magnets 7%, electronics 3%, and others 3% (USGS, 2011). Additionally, it is reported that the amount of recycling was quite small and consisted primarily of rare earth magnet scrap, although with the sharp increase in the price of rare earths, and the potential shortage in supply, focus in this area is continually growing. Thus, the opportunities, whether realistic or not, are extremely vast in the recycling of rare earth containing materials. The following subsections will present methods proposed for the recycling of rare earths based on the feed material type.RECYCLING OF RARE EARTH MAGNETSCurrently, investigations are ongoing in the area of recycling production scrap and end-of-life materials in the rare earth magnet industry. The following techniques illustrate potential methods for the recovery of rare earths from secondary RE magnet sources.Recycling of Rare Earth Magnet Sludge by Selective ChlorinationDuring the production of neodymium magnets, a by-product of production is the so called “magnetic sludge”. This by-product contains high amounts of neodymium, thus a process for the recovery of Nd has been proposed. In this process the Nd present is selectively chlorinated/distilled by the addition FeCl2 via the following reactions."

Jan 1, 2012

By John Loui Porathur

Highwall Mining has been recently introduced in India. The first Continuous Highwall Mining extraction in India started operating at Ramagundem Opencast Project-II (OC-II) of Singareni Collieries Company Ltd. (SCCL) in December 2010. A new hybrid empirical and numerical modelling approach has been devised to design web pillars for the initial Highwall Mining sites in India, considering the complex geology, such as existence of thick seams and multiple seams in close proximity. This paper gives the scientific elucidation of a comprehensive design methodology adopted for the above mentioned Indian Highwall Mining sites. The design technology includes web pillar design for multiple seams using hybrid empirical and numerical methods, slope stability assessment, ground movement monitoring, and recommendations for conducting blasting operations in the vicinity of Highwall Mining extractions.

Aug 1, 2013

By L. A. Homeniuk, R. J. McH. Clark

"The Maurice Bay deposit, the Stewart Island showing, the Fond-du-Lac deposit, the Middle Lake showing and the Nisto deposit are located on the North Rim of the Athabasca Basin. They are probably unconformity-related. These occurrences tend to be small. The Fond-du-Lac and Maurice Bay deposits are the largest and contain 450,000 kg and 650,000 kg of U10 8 respectively.Pitchblende is the main uranium mineral of all the occurrences, except at Middle Lake where autunite predominates. A II of the deposits are overlain and partially hosted by the Manitou Falls Formation of the Athabasca Group, except the Nisto deposit which is entirely within basement rocks, and the Maurice Bay deposit which is partially within the basement and overlying the Fair Point Formation of the Athabasca Group.The North Rim deposits are considered to be genetically similar to the other unconformity-type deposits found in northern Saskatchewan. It is suggested that a mechanical concentration of uranium may have occurred in heavy mineral beach sand type placers. The stability of the uranium minerals may have been enhanced by special local conditions. The fossil placers, after hydrothermal alteration and enrichment, would form the apparently ""rootless"" occurrences of uranium found totally within the sandstones above the unconformity.IntroductionAt least five deposits and showings and one train of mineralized glacial erratics of unknown provenance have been located on the North Rim of the Athabasca Basin from Maurice Bay in the west to Black Lake in the east. Distributed over a distance of 250 km, (Fig. l), they occur near the edge of the Basin, and are probably unconformity-related. The following have been identified from west to east (Fig. 2): The Maurice Bay deposit, the Stewart Island showing, the Isle Brochet train, the Fond-du-Lac deposit, the Middle Lake showing, and the Nisto deposit."

Jan 1, 1986

By A. Demers, M. Chapman, N. Reynier, R. Lastra, M. Courchesne, C. Laviolette

Historic medical isotope production at Canadian Nuclear Laboratories (CNL) in Chalk River involved the dissolution of irradiated isotope targets prior to extraction of Mo-99. This process generated liquid waste that was cemented in 5-gallon containers and transferred to an outdoor waste-management facility for intermediate storage. Research was undertaken to develop an innovative method for uranium, mercury and cesium recovery from the radioactive cemented waste (RCW). Regulations prohibit the removal of active radioactive waste from the Chalk River facility. Thus, CanmetMINING produced surrogate material following the same procedures and conditions to those used at CNL. The selective recovery of the uranium from the surrogate radioactive cemented waste (SRCW) could offer CNL more disposition options for the resulting wastes. Leaching tests were performed using four different SRCW at 1 kg scale. Different conditions, operating parameters, and the presence of plastic and corrosion products were evaluated on solubilization. The research investigated the use of potassium iodide with the sulphuric acid leach to increase metals recovery. Iodine improves the solubilisation of metals and the U dissolution reached 99%. The increase of leaching time reduces the U solubilization due to silica gel formation. Therefore, it will be important to control leaching time to avoid the loss of U during the pilot scale experiments. For Hg, the solubilization ranged from 60 to 80% due to the presence of metallic mercury and mercury sulphide found in SRCW cured at 60°C and/or aged for 30 months. Ion exchange (IX) was found the best method to separate the uranium from the impurities and produce a purified and concentrated uranium solution suitable for yielding a uranium product (yellow cake).

Jan 1, 2020

By Yuyong Li, Liangman Zhang, Zhaolian Wang, Shun Wang, Ltd. Shandong Huate Magnet Technology Co., Fengliang Liu

"Introduce a newly revolutionary magnetic separator - Raising Concentrate Grade and Decreasing Dregs Content Magnetic Separator Series JCTN (i.e. RCG&DDC MS JCTN). HUATE® JCTN is designed for rinsing, purification, desliming and thickening of the magnetic minerals as per different requirements. Adopting 240°-270° larger magnetic element with multi-poles and magnetic pulsation, and combining the devices of multi-channel rinsing water and top flushing water and new style tank, HUATE® JCTN can improve another 2%-10% concentrate mFe% than the traditional MS without lowering the concentrate recovery rate. Thereby, it solves the uneasy concentrate upgradation problem of the traditional MS resulting from the magnetic aggregation. Now, JCTN has been successfully applied in more than 30 mines in Australia, China and Russia, e.g. Sino Iron of CITIC PACIFIC MINING MANAGERMENT PTY LTD. HUATE® JCTN can optimize the industrial processing line by: 1) improving the discarding rate before milling to discard the necessary tailing ASAP; 2) getting in advance the final concentrate after milling. One JCTN can replace many traditional MS in series. In some way, it can also replace the anti-flotation separation process.INTRODUCTIONWe’re writing to introduce a newly revolutionary magnetic separator - Raising Concentrate Grade and Decreasing Dregs Content Magnetic Separator Series JCTN (i.e. RCG&DDC MS JCTN). HUATE® JCTN is designed for rinsing, purification, desliming and thickening of the magnetic minerals as per different requirements."

Jan 1, 2016

By Unknown

With the present-day trend of rising labour costs and a lowering of production efficiency of workmen, it has become imperative that every effort be made to use manpower to the greatest advantage and to mechanize mining as much as possible. During the past few years this trend has gained much prominence in the Porcupine camp. In view of this, the executive of the Porcupine Branch considered that the Mechanical Movement of Muck would be a very timely subject for a Symposium. Accordingly a Committee was formed, with A. K. Douglass, Mine Superintendent for Delnite Mines, Ltd., as Chairman, and the Symposium was held in the Auditorium of the McIntyre Community Building, Schumacher, on March 25th last. Papers dealing with shovel loader and mechanical scraper operation at six of the larger mines of the camp were presented and discussed, and a tabulation was prepared giving data on the machines in operation at a total of eleven mines. The papers and tabulation, reproduced below, will doubtless be of considerable interest to operators of mines in all parts of Canada.

Jan 1, 1948

By H. C. Gunnings, C. O. Swanson

"The Sullivan mine; at Kimberley in southeastern British Columbia; is the largest silver-lead-zinc mine in the Empire and one of the largest in the world.The original discovery was made in 1892 by four prospectors. Until 1899, when the branch line of the Canadian Pacific railway from Cranbrook to Kimberley was completed, little work was done on the property. In 1900, systematic development was started, and during the next 3 years 5,000 tons of ore was shipped to the smelters at Nelson and Trail. By 1903, some 300,000 tons of ore was developed, and a smelter was started at Marysville, about 5 miles from the mine. However, this smelter closed down in 1907 because of metallurgical difficulties after treating 75,000 tons, and the property came under the control of the American Smelting and Refining Company. An option on the property was taken in 1909 by the Consolidated Mining and Smelting Company of Canada, who exercised their option in the following year. During the next 5 years by selective mining and sorting 188,000 tons of high-grade ore was produced and shipped to Trail. This tonnage came from the upper levels, about 4,600 to 4,800 feet in elevation. At the same time, deep drilling down to the 3,900-foot level showed the presence of an immense body of complex ore. In 1915, the main adit-the 3,900-foot level-was started, and by 1919 this had been driven a distance of 2 miles to develop the ore above this level. Meanwhile, progress was being made in overcoming the milling problems. An interesting account of this work was written by the staff ( 4). In 1923, the first unit of the present concentrator was erected, with a capacity of 2,500 tons a day, and thereafter the rate of production increased rapidly. In 1934 it was around 8,000 tons a day, and to date a total of about 30,000,000 tons of ore has been sent to the mill. In recent years, a considerable part of the production has come from levels between the 3,900-and 3,350-foot, which were opened by an internal incline shaft started in, 1930. In 1942, tin was added to the products separated at the concentrator."

Jan 1, 1954

By S. W. Henley

"Shaft sinking design is typically driven by what has been successful in the past and the availability of sinking plant. This document considers a project where the sinking design and methodology is unconstrained by conventional thinking and removed from the commonly held belief that a sinking methodology should be developed from available winding plant. Schedule was a key driver for the Project and led to an alternative sinking design that aimed to optimise sinking advance rates by specifying new winders that compliment known sinking plant while providing improved safety, redundancy and flexibility within each part of the sinking cycle. KEYWORDS Consistent, Efficient, Flexible, Improved, Innovative, Optimise, Redundancy, Safety, Schedule INTRODUCTION The project is remotely located in the South Gobi region of Mongolia on a brownfield site and the scope of work included the concurrent blind sinking and concrete lining of two (2) ventilation shafts to an approximate depth of 1,150 m at a finished diameter of 10 m and 11 m respectively. All sinking and lining operations to be completed as in-line activities, (no lining whilst other activities are undertaken). The project was schedule driven with a completion date set for the first quarter (calendar) of 2021 and there were no restrictions imposed on the successful Contractor with respect to their equipment selection. Existing sinking plant already onsite from three previous shaft sinking operations would be made available to the Contractor if required on an as is where is basis Sustained advance rates in excess of 2.4 m per day would be required in order to achieve the completion milestone, therefore the design would have to include contingency and demanded flexibility to account for equipment down time. Previous shafts that had been sunk onsite have utilised a single double drum kibble (bucket) winder (hoist) with a single excavator loading on the shaft floor into a large capacity kibble (bucket). DESIGN Mucking The sinking design centred on the mucking cycle given that this is traditionally the most restrictive part of the sinking cycle and typically accounts for one third of the overall sinking cycle. The Vertical Shaft Mucker (VSM) and/or diesel excavator are commonly used plant for shaft sinking that were under consideration. The use of Cactus Grabs was not considered given the higher risk associated with grab ropes and hoist failures."

Jan 1, 2019

By E. Peek, L. Becze, K. Reading

"Gallium oxide is an important semiconductor material used in optoelectronic devices (flat panel and solar cell) catalysts and sensors. One of the methods to produce ?-Ga2O3 is the so-called hydrothermal route. It is practiced by Neo Gallium Compounds and comprises of two steps: (1) the production of mainly gallium-oxy-hydroxide in a pressure vessel by reacting metallic gallium with water at 200-220 ºC and (2) the calcination of gallium-oxy-hydroxide at 700-750 ºC to convert it into ?-Ga2O3. This paper describes this pressure hydrometallurgy process supported with relevant thermodynamic data and presents the characteristics of the ?-Ga2O3 powder produced for commercial purposes. INTRODUCTIONGallium is a relatively new metal, having been predicted by D. Mendeleev in 1871, discovered by P.E. Lecoq de Boisbaudran in 1875, and first commercially produced in the USA in 1943. Gallium is not rare, being more abundant in the earth crust than antimony, bismuth, molybdenum, silver and tungsten. However, few gallium minerals exist in nature, and the dispersion of gallium within other minerals add to the complexity of its recovery. In practice, gallium is found in dispersed state primarily in bauxites and in some sphalerites, and, to a much smaller extent, in some coals. At present, a very large proportion of the primary gallium in the world is recovered as a by-product of aluminum plants, mostly Bayer plants, where gallium is extracted from a bleed of the Bayer liquor (Roskill, 2011). In 2011, world production of primary gallium was estimated at 200 metric tonnes. In addition, there is a significant contribution of recycling to the overall yearly availability of the metal.Gallium exhibits fairly remarkable properties: it is liquid above 29.76 ºC, can be supercooled, and with its high boiling point (2204 ºC), is the metal with the widest liquid range. Gallium is magnetic, and is an excellent conductor of both heat and electricity. Gallium also displays a marked anisotropic electrical conductivity (Roskill, 2011). All these properties render gallium almost irreplaceable in the semiconductors (GaAs, GaN, GaSb, GaP wafers) and the optoelectronics industry (flat panel, solar cell)."

Jan 1, 2012

By I. Murray, N. Geoffroy

"Buried pipelines, tanks and other similar equipment are almost always present on large scale industrial sites, including in the oil and gas fields. However, as the proverb “out of sight, out of mind” suggests, it is easy to overlook proper maintenance procedures and simply assume that corrosion protection measures in place are working correctly. Unfortunately, this is not always the case, leading to significant environmental damage and loss of production. This paper describes several cases from various industries where buried equipment failed because of corrosion, sometimes with catastrophic results. It also presents various strategies, based on experience and new research, to help predict and prevent damage to underground metallic structures.INTRODUCTION Metallic underground structures are extremely common in industrial and commercial settings for numerous reasons. Burying pipes, tanks, wires and other similar equipment has numerous advantages: it provides significant protection from mechanical damage, frees up ground space that can be used for other purposes, requires little to no support structure and is generally more esthetically pleasing. However, this last benefit can also be considered the most significant disadvantage of underground equipment: becoming invisible and forgotten. While every engineer is aware of the importance of preventive maintenance, it is also human nature to somewhat forget about equipment that is hard to inspect and assume that everything is fine. This is unfortunately not always the case and failures in industrial settings can have extremely serious consequences. While economic aspects immediately come to mind (loss of production, cleanup cost, etc.), failure of underground equipment also results in an environmental and therefore public relations nightmare, especially in the oil and gas field. Leaks that would have been considered negligible in the past can now make national headlines and perfect reliability, while probably impossible to achieve, is now the goal of most companies. While environmental damage (real or perceived) is most often associated with leaks in the oil and gas industry, it can also affect the mining world. For example, the authors have worked on a project where a buried slurry pipeline had ruptured in the ground, causing a release of perfectly inert tailings. While the economic loss was low, the leak was reported in local media and caused a public relations problem."

Jan 1, 2017

By G. W. Neumann

"In order to avoid pollution of water in Flemming Brook and Little River, which drain the area in which the Brunswick No. 12 Mine and Concentrator are located, the company has gone to considerable expense in preparing tailings storage and effluent setting ponds. The attached drawing gives a plan of the six settling ponds together with elevations of the dikes and the effluent weirs.All original dikes for the six ponds were constructed from humus-free clay and rock material, which was obtained, preferentially, by excavating from within the dike area. Run-off water, precipitated on the outside slopes of the dams will drain off without contacting the tailing material. A ditch was made north of the dam site to deflect surface run-off to the east into a branch of Flemming Brook.A secondary dike, made from tailings, has recently been erected on No. 1 and No. 2 tailings pond inside and above the earth-filled dike which serves as a roadway. Run-off from the tailings dikes will be retained inside the ponds by ditching between the roadway and tailings dike into ponds 4 and 6."

Jan 1, 1969

By Robert B. Parsons

"The annual onslaught of provincial budgets and tax changes is complete, and once again the Canadian taxpayer is being asked to dig deeper into his pocket to fund old and new programs. It is noteworthy that 1987 tax reform promised lower taxes, but a broader fax base. Five years later, we still have the broader tax base, but the lower faxes have gradually crept up to pre-tax reform levels. Surprise! Surprise!IntroductionThe last edition of Tax Notes commented on some important proposals announced in Manitoba's 1992 budget. In this issue, Tax Notes summarizes the 1992 budget proposals of British Columbia, Ontario and Quebec. These budgets reflect the continuing trend of transferring responsibilities and the related costs-from the federal government to the provinces. As well, the budget papers bear witness to the respective governments' political stripes. British Columbia, Ontario and Quebec are seeking higher tax revenues. Only Quebec continues to acknowledge the importance of the mining industry in its annual budget documents."

Jan 1, 1992

By D. Gagnon, B. Dubreuil, J. -M. Lalancette, D. Lemieux

"The pilot scale extraction of gold with a brine of sodium chloride and bromide at 30 ºC, in an atmosphere of halogens at atmospheric pressure, leads to gold chloride with 95% gold recovery. The use of dilute hypohalites (1 – 3%) instead of free halogens, which is strong enough to oxidize hypobromite into bromine, simplifies the recycling of halogens by electrolysis. With the recycling of water and brine, the regeneration of hypohalites and with a barren solid that is inert and stable. The Nichromet Extraction technology is a green process where the protection of the environment does not preclude profitability.INTRODUCTIONThe use of chlorides for the extraction of gold predates the discovery of chlorine by Scheele in 1774. In the Plattner chlorination process (Christy, 1888) sodium chloride and copper salt were used to promote gold recovery by amalgamation with variable results. The introduction of the cyanide technology in 1889 has led to a general use of this method for gold recovery. In the last decades, a return to chlorine in extractive processes has been noted (Ferron, Fleming, O’Kane and Dreisinger, 2002), mostly because of environmental pressure for non-cyanide technologies.This paper describes a closed circuit proprietary approach (Lalancette, 2009) developed and piloted by Nichromet Extraction Inc. for the extraction of precious metals with recycled mixed halogens; chlorine and bromine from hypohalites. DESCRIPTION OF THE PROCESSThe attack of gold by halogens can vary significantly. The rate of reaction is substantially higher with bromine (Br2) than with chlorine (Cl2), by a factor of more than five, although the oxidation potential of Cl2 is higher than Br2, as shown in Equation 1a and Equation 1b (Latimer, 1952)."

Jan 1, 2012

By G. Avramovic-Cingara

Grain boundary characteristics and microstructural evolution are analyzed in a comparative study using orientation imaging microscopy (OIM/SEM) and transmission electron microscopy (TEM/SAD). The subgrain sizes and misorientations were determined by the OIM for aluminum deformed in torsion to equivalent strains between 0.2 and 4 over the temperature ranges of300-600°C and strain rates 0.01-1 s". The OIM gives clearer evidence of boundaries with high misorientation than does TEM, but it overestimates their frequency b y missing boundaries less than 1 0. T EM more clearly reveals low-angle arrays of widely spaced dislocations resulting in finer subgrain sizes than those indicated by OIM. The evidence supports a mechanism combining dynamic recovery (DRY), deformation band formation with permanent boundaries and geometric dynamic recrystallization (gDRX) in contrast to the hypothesis known as continuous dynamic recrystallization (cDRX).

Jan 1, 2004

By M. A. Cawley, J. W. Jordan

"IntroductionTHE ORE PILLARS in the lower ""A"" ore body of Waite Amulet Mines, Limited, can be divided into two groups, those mined in the open by sub-level blast-hole methods, and those to be mined .against coarse rock fill. Of the three pillars in the last group one has been mined and is dealt with in this paper. The method of mining pillars against coarse rock fill was suggested by the late Dr. Oliver Hall, who was Consulting Engineer for the Company when recovery of No. 2 East pillar was being planned.HistoryThe Waite Amulet mine is in northwestern Quebec, nine miles north of the town of Noranda. The property is approximately three miles long by one mile wide. The present Company, which was formed by the amalgamation of Amulet Mines, Limited, and Waite Ackerman-Montgomery Mines, Limited, commenced operations in the summer of 1937. In the fall of 1939 a new .flotation mill was erected with a capacity of 1,200 tons per day, which was increased to 1,800 tons per day in 1943. The mill is presently operated at 1,400 tons per day.To date, seven orebodies have been found, the major ones being Lower A, East Waite, and Waite. Three separate concentrates are produced, copper, zinc, and pyrite. Total tonnage mined to the end of 1954 from all orebodies has been 7,340,000 tons, which averaged 4.6 per cent copper, 5.3 per cent zinc, and 0.037 oz. gold and 1.27 oz. silver per ton."

Jan 1, 1955

By Andrew Barnes

The adsorption capacity of peat collected from a proposed mine development in northern Sweden has been determined using laboratory column experiments in which peat was irrigated with a simulated (acidic) waste rock dump leachate. The simulated leachate was made using a hydrogen peroxide leach of composite waste rock from the proposed mine development. The waste rock samples were composited in proportion to their predicted extractable tonnage for the mine development in order to generate a more representative leachate solution for the waste rock facility. As expected the test revealed that the peat material shows a very high affinity for attenuation with greater than 70% of Co, 90% of Ni and 95% of Cu removed from influent solutions through the majority of the tests demonstrating the potential benefits in mine water treatment. In contrast, it was found that Fe is initially released from the peat at concentrations up to 100 mg/L and can mean potential problems for the water released depending on the receiving environment. The exact mechanisms for Fe release is uncertain, though it is suspected that ion exchange / competitive desorption is responsible. Inspection of the laboratory results and drainage data from the natural peat wetland receiving drainage during overburden prestriping and mine development at the mine site are comparable, confirm the validity of the experiments, and further emphasize the potential for future use of pre-stripped peat material in managing water quality.

Aug 1, 2013

By P. Personnet, D. Wheaton, E. Couzinie, V. Demetriou, Brooks. W., G. Girault, M. Meyer, L. Charbonnel

A common problem in Gas Treatment Centers (GTC) from primary aluminium smelters is the temperature of the gas to be treated : above a threshold, filtering media are irreversibly damaged. The traditional way of dealing with high gas temperature is to dilute with fresh air, which implies over sizing - and therefore higher cost for - the GTC in order to have the capacity to treat this dilution air without compromising on pot suction. A system was developed which decreases gas temperature without having to use dilution air. This system is based on water pulverization in gas collectors. The water vaporization leads to a temperature decrease of the gas. A pilot system was trialed in our R&D unit. Satisfactory results led to the development of an industrial system based on Envirocare equipment (partnership), which was trialed in our production plant in Tomago (NSW, Australia). This patented system was then generalized in this plant, which is now using it with success during austral summer.

Jan 1, 2006

By K. Soga

DOWA has long been specialized in the treatment of complex massive sulfide ores from exploration through smelting. Its competitive advantage derived from ore dressing technology to dress and concentrate complex ore to various kinds of metals concentrates. With this technology, the company recovers as many as seventeen different nonferrous metals. Therefore, it is crucial for the environment management and recycling business both to recover valuable elements like gold, silver, copper etc. and to handle hazardous elements in safety. From this view point, the nonferrous metal industry has a potential to play an important role; that is "The Anchor of Recycling" or "The Joint of Recycling Loop". By utilizing these mining, smelting and refining technologies, know-how and facilities, DOWA became a leading waste treatment, soil remediation and metal recycling company in Japan. This knowledge is now being applied in China .

Jan 1, 2007

By Wei Yun-Jie

Columnar jointed basalt is a fractured rock, with a lot of small spacing structural planes and poor integrity of the rock mass. On the basis of the comprehensive study of the columnar shape of Columnar joints, rugosity of the fracture surface and the chemical composition of basalt, columnar joints of Bai hetan dam area were formed as a result of the cooling and shrinkage effect of magma. Columnar joints basalt are mainly chlorite, kaolinite, epidote, tremolite chemical reactions and the content of columnar joints are mainly chlorite by slice identification and chemical analysis. Columnar joints basalt showed high uniaxial tension test, low coefficient of friction and high cohesion by indoor physical and mechanical test. Columnar joints rock mass showed high strength and large deformation by field shear test and deformation test. Columnar joints basalt can be used directly as a foundation of dam as long as we follow the rules and reduce disturbance strictly.

May 1, 2009