Search Documents

By Gordon A. Irons, H. Y. Hwang

An impinging gas jet on a water surface was studied to understand momentum transfer in oxygen steelmaking. Depth, width and oscillation frequency of the jet cavity were measured and the splashes interpreted with Kelvin-Helmholtz instability and combined Rayleigh-Taylor and Kelvin-Helmholtz instability theory. A model to calculate separate gas and liquid velocities, applying the exact momentum boundary condition, is proposed.

Jan 1, 2004

By J. Fellowes, V. Landais, J. Robson, J. Carr

"Aerospace Al-Zn-Mg-Cu (7xxx) alloys are known to be susceptible to environmentally assisted cracking (EAC). This phenomenon has been studied intensively for many decades, leading to empirically adopted methods to mitigate this problem through overaging and composition design. In parallel, many theories have been developed to explain EAC in 7xxx, but none is yet universally accepted. Today, a number of emerging techniques offer potential to shed new light on EAC in 7xxx. The purpose of the present paper is to demonstrate how X-ray tomography (XCT) combined with electron microscopy can be used to identify the true crack path in 3-dimensions, and hence identify material for site specific electron microscopy analysis. Composition mapping over large areas to high accuracy has been performed using a modern electron microprobe analysis system. This has been combined with transmission electron microscopy to investigate local composition in matrix and precipitates at high resolution. This combination of techniques across length scales offers the potential to provide new insights into the links between local composition, microstructure, and EAC resistance.INTRODUCTION Environmentally-assisted cracking (EAC) is a phenomenon which dramatically decreases the performance of metals and can cause premature failure of large structures. Observed in situations where components were not subjected to critical loads and no widespread corrosion was involved, this type of brittle failure is extremely difficult to predict. The EAC designation covers a number of phenomena, e.g. stress corrosion cracking (SCC), hydrogen embrittlement (HE), corrosion fatigue (CF), etc. Initially identified in steels, EAC can also affect other metals such as high-performance aerospace aluminium alloys, and this phenomenon has been a concern for industries for decades. Extensive research has been conducted on the effects of various environments (moist air, saline water, dry hydrogen gas, etc.) on microstructures and crack propagation, however no consensus has been reached and the exact nature of the mechanisms that control EAC is still being debated (Birnbaum & Sofronis, 1994; Gangloff, 2007; Holroyd & Scamans, 2013; Lynch, 2012; Oriani, 1972; Scamans, Alani & Swann, 1976, Young & Scully, 2002)."

Jan 1, 2018

By Mark Holdsworth

In 2002, Kennecott Utah Copper Copperton Concentrator installed an Expert Control system for optimization of their SAG and Ball milling circuits. The advanced process control has been well received and is utilized well over 95% of the time. In the years since, many lessons have been learned and many advances have been made. Improvements have produced millions of dollars of benefits and have included directly controlling feedrate with complex logic as opposed to using a bearing pressure controller, modifications to how sound is used for control, modifying logic for maximizing asset utilization and using advanced control for automating equipment restart.

Jan 1, 2012

By Adrian E. Scheidegger

"AbstractThe possibilities of deriving pertinent information about fractures in an oil pay from data obtained by core analysis are investigated. It is shown that it is possible to obtain an estimate of the fractured area per unit volume of the pay, and that the size of the fractures can be estimated if their shape is known. A suggestion of a routine procedure for the analysis of fractures is given.1.-IntroductionMany oil fields are producing essentially from cracks or fractures. Where this is the case, it is important to be able to obtain a knowledge of the size and distribution of those fractures in the oil pay. This knowledge has to be derived from the analysis of cores taken from the fields, as it is generally impossible to follow a fracture through the pay by direct means. The necessity of using statistical methods to extrapolate the meagre information obtained from the cores of the wells is therefore indicated.It is known that the fractures are much bigger than the diameter of the cores; thus, if they strike a core, the latter will generally fall into two pieces. The angle of the fracture with the vertical can be measured and, if oriented cores are taken, the exact position of the surface element representing the intersection of the fracture with the drill stem can be determined. Sometimes the edge of a fracture can be seen in a core. The number of •Cores that show such an edge can be noted. Of course, one has to be careful to distinguish between original fractures in the pay and fractures in the core caused by drilling operations. Only the former are relevant."

Jan 1, 1955

By A. D. Walters

"IntroductionScreens are used in coal preparation plants for four basic functions, namely:I. Scalping off large size run-of-mine coal for initial size reduction;2. Sizing of coal treatment in different process streams;3. Removal of magnetite (dense medium) from clean coal and refuse;4. Dewatering.Canadian coal preparation plants use screens extensively in the above functions. Even plants where no beneficiation takes place, screening and crushing are carried out in the size reduction process.Description of Process UnitsThe type of screen used in coal preparation plants generally falls into the following categories:Fixed Screens and Grizzlies (for large coal)Often a simple rugged construction, either set horizontally above a bin or inclined with the coal flow.Fixed Sieves (for fine coal)They are used for dewatering and/ or size separation of slurried coal or discard. The sieve bend, the Vor-Siv, the Wilmot riffle and the cross flow screen fall into this category. The most commonly used in coal preparation plants is the sieve bend, Figure 1. Coal slurry is fed tangentially onto a fixed curve wedge wire screen deck. The solids are separated at a predetermined particle size, delivering a partially dewatered overproduct and a dilute underflow. The coal slurry is initially delivered to the sieve bend via a feed box. A series of baffles spreads the feed evenly across the width of the deck. The slurry drops from the last baffle, passes through the feed spout and is fed tangentially to the screen. It is important that the feed should contact the surface immediately at the front end of the sieve bend. It is possible to lose as much as 250Jo of screening area with a poorly fitted screen box.The full stream of coal slurry flowing over the sieve bend decreases in depth, in increments of approximately •;4 the slot width each time it passes a slot. Sieve bends make a size separation at 112 to 2h the slot width. This feature virtually eliminates blinding of the screen surface. Slot sizes are normally quoted in millimetres, available standard slot sizes are from 2 mm to 0.125 mm. The sieve bend is also widely used in coal preparation for preliminary dewatering."

Jan 1, 1989

By Nirmal Weerasekara

Mill liners serve the dual purpose of protecting the shell from wear and transferring the rotary motion of the mill to an effective grinding action. As the liners wear, the efficiency of energy transfer changes, so there is balance between liner profile for wear and for milling efficiency. A tool that can simultaneously predict the evolution of the liner profile and the associated change in milling efficiency should prove most useful in optimal liner design. This paper presents such an approach, based on measured 3D liner profile data informing 3D DEM simulations of charge motion and liner wear modelling.

Jan 1, 2012

By F. Calizaya, S. Bhattacharyya

"This study presents the results of a set of sound level measurements carried out in three underground mines where auxiliary fans are used regularly. Sound levels as high as 100 dB(A) by the workings and 115 dB(A) by the fans were measured in these mines. These levels are quite high even for intermittent noise. Ventilation layouts and best practices used to overcome potential problems related to overexposure to fan noise in underground hard-rock mines are presented here. Factors such as fan type, rotational speed, and silencer-duct arrangements and their effects on noise attenuation are discussed. INTRODUCTION Auxiliary fans are used in hard-rock mines extensively. They are used to ventilate development headings, crusher rooms, conveyor transfer points, and underground shops. They are also used in developing long tunnels and ramps. Depending on the flow requirements and space restrictions, single or double stage axial fans with rigid or flexible ducts are used. Usually, they are high pressure (3.75 kPa) fans with flow rates ranging from 7.1 m3/s to 30 m3/s. The input power varies from 15 kW to 113 kW (Mutama, 2004; O’Connor, 2008). Typically, a 113 kW fan can produce sound levels as high a 113 dB(A) (Howes, 2005). Silencers are often omitted for cost reduction purposes or when used, they are not well maintained. Furthermore, silencers provide limited attenuation depending on their length and type. Typically, the sound attenuation ranges from 10 dB(A) for a 1 × D silencer to 14 dB(A) for a 2 × D silencer, where D is the fan diameter. In a mine, the silencer is subject to wear and tear, especially when the silencer is used in harsh environments. The interior lining can get clogged and the acoustic fill can get covered by dust and diesel soot, thus reducing the silencer performance. Periodic cleaning of the interior casing can increase the attenuation capacity of a silencer by 6 to 9 dB(A) (Dabson & Acuña, 2017). However, this requires a special silencer design in which the inner cartridge can be removed, the sound absorbing material replaced, the inner casing cleaned and the whole set retrofitted. A number of techniques can be used to reduce auxiliary fan noise in underground mines. These range from selecting the right fan for the job to installing adequate silencers. The choice depends on the air quantity requirement at the working place, cross-sectional area of the opening, duct diameter, fan type (axial or centrifugal) and local restrictions. Auxiliary ventilation layouts and best practices used to overcome potential problems related to overexposure to fan noise in underground hard rock mines are presented here. Factors such as fan type, rotational speed, duct diameter, and silencer-duct arrangements and their effects on noise attenuation are discussed."

Jan 1, 2019

By S. Isaac

The networks of interdependencies between elements in building projects, referred to as the project topology, are often complex and difficult for project teams to comprehend. It is hypothesized that a graphbased model of the project topology can be based on existing data in Building Information Models (BIM), facilitating the application of graph-theoretic algorithms to analyze this topology. The objective of this study is to propose an outline for the synthesis of BIM and graph theory. This synthesis is expected to contribute to the development of new tools for representing, managing and analyzing the design of building projects.

Aug 1, 2013

By H. Thalenhorst

For an advanced mineral exploration project that has a ?nugget? issue making the assessment of the deposit grade difficult, a bulk sampling program using a sample tower can provide information that is otherwise not obtainable prior to actual production. This information includes the verification of predicted resource grades for the bulk sample tonnage (and, indirectly, of the methods and parameters used for the grade estimate), confirmation of the physical and grade continuity of the mineralization, and geotechnical data for a future mining operation. The information gathered will improve the input of a feasibility study, particularly with respect to expected mining grades, which are the key economic parameter for most mining projects. The bulk sample rejects can be used for pilotscale metallurgical testwork. Bulk sampling is also useful in cases of potentially biased drill-hole assay results and in the reliable determination of ore grade before shipment of ore from production or development operations to an external beneficiation plant. This paper presents a practical bulk sampling and sample preparation protocol, lists design features for the sample tower, examines the sampling errors that will be encountered, provides information on quality control procedures, and looks at the costs and benefits of such a program, based on the experience of undertaking bulk sampling programs during the period of 1985 to 2008.

May 1, 2010

By A. L. Valdivieso

"The correlation obtained by plotting pH of maximum adsorption of dextrin versus the isoelectric point of involved metal hydroxides can be used to predict the depressing effect of dextrin on flotation in ""pure"" sulfide mineral systems. Sulfides are strongly depressed by dextrin whenever their surfaces are coated by the corresponding metal hydroxide. The efficiency of dextrin as a depressant is affected by the adsorption of the sulfhydryl collector. Hydrolyzable cations modify this relationship in flotation of sulfide ores. This type of deviation of the real-life systems from the predictions based on the behavior of the pure systems shows the possible ways that could be followed to further improve the obtained correlations. Advances in Mineral Processing Science and Technology Proceedings of the 48th Annual Conference of Metallurgists ofCIM Sudbury, Ontario, Canada Edited by"

Jan 1, 2009

By R. T. Jones

"Technical publications in the field of mining and metallurgy have existed for a long time. Recent developments in electronic publishing on websites make it possible to disseminate information more widely and cost effectively than before. Professional societies have an opportunity to serve their members and their industry by publishing high-quality peer-reviewed papers on their websites as well as in printed form. Older publications can be scanned, and optical character recognition can be used to provide searchable text. Various business models exist around this process. This paper outlines the approach used by the Southern African Institute of Mining and Metallurgy (SAIMM) to provide free open access to their journal papers and conference proceedings, as well as the work being done by OneMine.org to collect technical papers from a number of international societies and make them available to subscribers via a large database. An approach is outlined that should be of benefit to authors, readers, and society at large.INTRODUCTIONGeorgius Agricola (1494-1555) was not the first writer on the subjects of mining and metallurgy, but is well known as the author of De Re Metallica (‘of things metallic’ or ‘on the nature of metals’), a book that documents and illustrates the observations he made in the course of his extensive travels in the 1500s. Agricola wrote extensively about mining methods and metallurgical processes that were in place in the Middle Ages. The original Latin version of De Re Metallica was published in 1556, the year after Agricola died. It was translated into English by Herbert Hoover, a mining engineer and later President of the United States, and his wife Lou Henry Hoover, a geologist and classicist. The English version of De Re Metallica was published in 1912."

Jan 1, 2012

By C. O. Swanson

THE purpose of this paper is to discuss the use of the dip needle in the field of mining geology. The subject matter is new only to the extent that it reflects the writer' s added experience in recent years. The treatment is brief, and those interested in a more extended analysis are referred to the articles listed at the end of the paper. In the discovery and tracing of mineral deposits, the clip needle, like most other geophysical instruments, can be used in two ways. One method may be termed direct; the other, indirect. The direct method is that of finding or following certain ore-bodies by virtue of their magnetic properties. Explicitly, or by inference, it is the method which many mining men and practising geophysicists have in mind when they consider whether or not a certain property should be studied by geophysical means. In the ideal case, this method demands little or no knowledge of geological conditions. The indirect method uses the clip needle as an aid to purely geological studies in working out the structure of a mineralized area. Although not as simple as the direct method, it enjoys a much wider field of usefulness. The writer's experience in the past fifteen years, which is believed to be typical, is that the indirect method finds application four or five times as often as the direct method. The indirect method is of particular value because it furnishes information concerning the relationship between geological structure and ore occurrence. Most mining engineers will agree that structural control is an important factor in the localization of ore deposits, and therefore that the subject under consideration is of some interest in mining geology. Specifically, then, the present purpose is to outline the principles and practice of using the clip needle in working? out geological structure.

Jan 1, 1941

By J-P. Rossetti, A. Guerin, M. Jaboyedoff, L. Baillet, A. Mariscal, J. D'Amato, D. Hantz

"The processes leading to the fall of rock compartments from rock walls are poorly known as well as their velocity. It ensues that quantitative prediction of the failure time for a rock compartment which is presently stable, is not possible by a purely geomechanical approach. However a quantitative probabilistic prediction of rockfalls at the scale of a rock wall is possible if the spatial-temporal rockfall frequency can be determined or estimated (Hantz, 2011). For a better knowledge of failure processes and frequency, rockfalls have been detected in several rock walls, using annual terrestrial laser scanning, allowing comparison of the frequencies in different geological conditions. For one of these rock walls, the spatial detection have been completed by a precise dating of the events, using a quasi-continuous photographic survey (one photo every 10 mn), allowing the study of the influence of meteorological factors.The precise dating of rockfalls has been carried out for the Saint-Eynard cliff which towers above a residential area of the town of Grenoble (French Alps). The South-East facing cliff consists in bedded limestone gently dipping North-West and located at an elevation between 850 m and 1100 m. The surveyed zone is about 750 m large and 250 m high. Between 01/02/2013 and 26/11/2013, 65 rockfalls ranging between 0.01 m3 and 20 m3, have been detected by diachronic comparison of laser scanner data and dated by comparison of photographic images. The temperature at the elevation of the cliff has been calculated from the temperature measured (every 5 mn) at a meteorological station located at an elevation of 245 m and 2.5 km away from the cliff, using a temperature gradient of 0.003°C/m (D’Amato et al., 2014). The precipitation were measured 900 m away from the cliff at an elevation of 469 m. Different meteorological conditions have been defined: (a) “freeze” qualifies days with negative mean temperature (but with a thaw period, except for two days); (b) “thaw” qualifies days with positive mean temperature, but following a freeze day; (c) “rain” qualifies days with precipitation.Table 1 shows the rockfall temporal frequency for the different meteorological conditions. It appears that the frequency is about 6 times higher the freeze days, 2.5 higher the thaw days and 3 times higher the rain days than days without freeze, thaw or rain."

Jan 1, 2015

By Curtiss O. Ehrsam, M. Naseem Mian

Alaska’s Red Dog Mine is strengthening its position within Cominco’s “Vision 2000”strategic plan by continually improving quality and quantity of production while reducing costs. Red Dog has evolved into a stable and mature operation, after six years of milling experience. A high grade, partially oxidized orebody in the severe Arctic environment, along with competing producers in a volatile metals market, are the continuing challenges facing Red Dog. The Red Dog Mine is striving to meet these challenges with emphasis on operator training combined with creative systems development and increased production. This paper describes developments in operations along with future plans.

Jan 1, 1996

RÉSUMÉ L’estimation la plus précise possible des coûts de minage est d’extrême importance pour les études de préfaisabilité afin de diminuer les risques financiers des projets miniers. Les méthodologies existantes d’évaluation des coûts de minage ne permettent pas de les évaluer avec des marges d’erreur acceptables tout au long de l’évolution des projets miniers. Elles visent à évaluer les coûts unitaires de minage des études préliminaires de faisabilité, pour les principales méthodes d’exploitation, en prenant pour l’hypothèse que ces coûts dépendent principalement du taux d’extraction journalière. Si cette hypothèse peut être justifiée pour l’évaluation du coût d’opération, elle est fort discutable pour l’évaluation des coûts de minage. Pour démontrer que cette hypothèse est inadéquate nous avons analysé la méthode d’exploitation la plus populaire sur le continent nord-américain c’est à dire celle par chambres vides avec retrait horizontal (Hr – Horizontal retreat), ou « Longhole » et celle avec retrait vertical (VCr - Vertical Crater retreat). Il ressort de cette analyse que les coûts unitaires de minage dépendent principalement des conditions géotechniques du massif rocheux et de la largeur du gisement et non pas du taux d’extraction journalière du minerai.

Jan 1, 2010

By J. B. Yianatos, F. A. Contreras

Mineral carrying rates across the pulp-froth interface in the range of 1.4-3.2 tph/m2 and bubble surface coverages between 7 and 22 %, have been determined in large rougher flotation cells operated under normal conditions. To evaluate these variables, measurements of bubble size distribution, bubble load and size distribution of particles collected by true flotation, were performed at different concentrators. A model for estimating the bubble surface coverage at the pulp-froth interface level as a function of bubble load, Sauter mean bubble diameter and particle size distribution of the mineral collected by true flotation, was developed. Bubble loadings in the range 24-70 kg/m3, bubble sizes between 1.5 and 3.2 mm and superficial gas rates between 1.2 and 2.0 emfs, were measured in copper rougher flotation cells under normal operating conditions. Estimated bubble surface area fluxes were in the range 31 to 62 cm2/s/cm2- Results of carrying rates and bubble surface coverage, at the pulp-froth interface, were significantly lower than the maximum carrying rate for the collection zone, indicating that in this case is difficult to achieve maximum carrying rate at the pulp-froth interface level. The main constraints regarding carrying capacity limitations are then related to the froth transport characteristics (i.e. cell design, froth residence time, froth stability, froth recovery). Advances in Mineral Processing Science and Technology Proceedings of the 48th Annual Conference of Metallurgists ofCIM Sudbury, Ontario, Canada Edited by

Jan 1, 2009

By S. Kelebek, E. Yalcin

"Diethylenetriamine (DETA) and/or triethylenetetramine (TETA) are reagents that can generally be categorized under ""flotation modifiers"". These polyamines are known to be effective for the deactivation/depression of pyrrhotite that is present in Canadian nickel-copper sulphide ores in large quantities. Recent bench scale testing on some of these complex ores indicated that chalcopyrite flotation can also be adversely affected under certain conditions involving polyamines, which may be taken to be an evidence of their specific affinity towards chalcopyrite. In general, DETA shows no significant depressant action on chalcopyrite while TETA's promotion of hydrophilicity for this mineral has been observed even in the presence of xanthate. This prompted an investigation on thermodynamic equilibria involving these polyamines and copper ions. Results serve a useful purpose to identify conditions for deactivation phenomena. CuDETA2+ and CuTETA2+ chelates as products of sequestration have large predominance areas covering a wide range of redox and pH conditions, where copper xanthate species are not stable, especially in the presence of TETA."

Jan 1, 2009

By H. J. lgner

Hydraulic fills are widely used in the tabular, steeply dipping stopes of the South African gold and platinum mines as an integrated process within a daily cycle of drill and blast. There is therefore only a small time window in which to fill the geotextile bags used as primary fill containment, without the risk of loosing production. Consequently, mines tend to increase the flow rate to the stopes, although this compromises adequate drainage, consolidation and strength development during filling. Recent underground measurements inside the geotextile bag have revealed that at high rates of rise and at 25 degrees dip, the backfill can remobilise within a limited area inside the geotextile bag during filling. This sudden downward surge of backfill exerts, for only a few seconds, additional loading on the geotextile, its supporting mesh and the props. This unstable behaviour poses a serious threat as it can push props out of place, thereby damaging the geotextile bag and causing a mud slide in the stope. To reduce the risk of accidents, the phenomenon of sudden slumping was further investigated for various filling conditions in the laboratory. The results confirmed that the maximum pressures associated with the sudden slumping can be more than five times those experienced during steady-state consolidation. Based on this new insight, the current best practice for hydraulic backfilling was critically reviewed. A practical approach to implementing meaningful standards is presented to ensure safe operations in relation to the consistency of the backfill quality and the appropriate matching of geotextile characteristics with backfill properties.

May 1, 2007

By McGill Metals Processing Centre, S. Chang, L. Calzado, X. K. Cao, C. H. Hsin, M. Isac

"Due to the increasingly stringent cleanliness requirements for final steel products, there has been a growing interest in the possible use of micro-bubbles for the removal of inclusions with diameters smaller than ~50µm, present within the steel passing through a steelmaking tundish. However, several technological barriers have prevented the adoption of this technique in industry. These are related to a) the generation of micro-bubbles in liquid steel, b) the measurement of bubble size distributions, and c) the optimization of bubble injection conditions to create micro-bubbles. In the present study, a novel Aqueous Particle Sensor (APS) system was developed for the in-situ, on-line, detection of micro-bubbles in water, generated by a newly designed full-scale ladle shroud, located at McGill Metal Processing Centre (MMPC). Measurement results from the sensor were validated against bubble size data collected through a high speed camera and post-processed through the commercial software, Image J.Control variables and orthogonal experiments were designed to assess the dependence of average micro-bubble sizes and bubble size distributions on key experimental parameters. Those chosen were the air inlet flowrate, the distance of the gas injection port from the slide gate, and the number of injection ports used. The investigation demonstrated that the APS system can be successfully adapted to detect micro-bubbles up to ~800 micron diameters. Using this novel sensor, it was shown that multi-port injection using low air inlet flowrates, closer to the slide gate, were useful in forming small micro-bubbles within the flow through the ladle shroud. The results from the APS system were compared and validated against data resulting from an optical technique. INTRODUCTIONModern industry expects increasingly stringent cleanliness requirements for final cast products. Therefore, the numbers and sizes of inclusions need to be strictly controlled in steelmaking operations. Thus, the cleanliness of steel products depends on the amount, morphology and size distributions of nonmetallic inclusions in steel (Zhang L. & Thomas B., 2003). Since large, deep, tundishes provide longer nominal residence times for liquid steel passing through it to the exit SEN’s, this can provide the ideal place to separate inclusions, and bubbles can assist by removing help attach inclusions and float them to the top surface."

Jan 1, 2016

By M. Cai

"It is well known that Peak Particle Velocity (PPV) plays a critical role in triggering rockburst damage in burst-prone underground mines. To estimate the PPV distribution around excavations, advanced numerical modeling can be used. In wave propagation numerical modeling, velocity field is often assumed to be uniform around an excavation. However, it is observed that wave velocities near mine openings are not constant, but rather non-uniform. Wave velocity in a rock mass depends on many factors such as rock quality and confinement. In particular, confinement has a large influence on wave velocity. The confinement around an excavation is low at the wall boundary and increases gradually and reaches a constant value far away from the excavation boundary. Hence, stress redistribution due to excavation will have a profound influence on wave propagation in underground mines. A better understanding of the influence of excavation effect on wave propagation helps to interpret the field observation of rockburst damage and improve mine safety. For this purpose, a non-uniform velocity model need to be constructed and the influence excavation effect should be taken into account in numerical wave propagation modeling.In the present study, a non-linear velocity model is developed firstly by considering the influence of confinement on wave velocity. This model links wave velocity to confinement explicitly. A coupled numerical method is then developed and used to study the seismic wave pattern around excavations in underground mines. Two codes, FLAC and SPECFEM2D, are coupled in the analysis. The motivation of developing the FLAC/SPECFEM2D coupled approach is to take merit of each code, such as the stress analysis capability in FLAC and the powerful wave propagation analysis capability in SPECFEM2D. The coupling process is realized through three steps: (1) static stress redistribution around an excavation is analyzed in FLAC; (2) data for coupling analysis, such as non-uniform velocity field (based on the new developed velocity model), mesh, absorbing boundaries, etc., are generated by FISH functions in FLAC and passed to SPECFEM2D; and (3) wave propagation modeling is performed in the SPECFEM2D considering a fault-slip seismic source. Because stress redistribution around the excavation is considered, non-uniform velocity field for the SPECFEM2D model can be obtained and this is a notable feature of this study. Very large difference in the S-wave response in these two modeling approaches with uniform and non-uniform velocity fields can be seen from the modeling results.Using the FLAC/SPECFEM2D coupled modeling approach, accurate velocity models can be constructed and this in turn will help to produce accurate PPV distribution around the excavations. Accurate PPV contours can be used to identify high rockburst risk zones for improved dynamic ground support strategy."

Jan 1, 2015