Search Documents

By R. S. James, S. P. Goff, A. E. Armitage

"Abstract - Oxide-facies banded iron formation in the Third Portage Lake area is hosted by ultramafic and calc-alkaline volcanic rocks and related sedimentary rocks of the Archean (2.8 Ga) Woodburn Lake Group, 80 km north of Baker Lake. These rocks record at least two phases of metamorphism/ metasomatism. Greenschist facies metamorphism, in the temperature range of 370°C to 520°C and at pressures above 2.3 kbar, has affected all rocks on a regional scale. Later mineralization and alteration of banded iron formation (BIF) and associated volcanic rocks resulted from metasomatic fluids which carried Mg, K, Ca, S, As, Cu and Au. These fluids were confined to ductile to brittle, cross-cutting and layer-parallel micro-shears developed in the thickened hinge region of a shallow plunging recumbent fold. Metasomatic reactions yielded cummingtonite + biotite-bearing assemblages which are associated with strongly mineralized iron formation. Pyrrhotite is the dominant sulfide phase and occurs within ductily deformed iron formation where it pervasively replaces magnetite. Minor fine-grained chalcopyrite and arsenopyrite generally occur as inclusions within pyrrhotite and recrystallized magnetite, and rarely as individual grains. Pyrite is restricted to brittlely deformed iron formation, and to the contact between iron formation and altered ultramafic rocks, where it is associated with quartz veins. Pyrite typically replaces pyrrhotite. Native gold is associated with both pyrrhotite and pyrite, but higher gold concentrations are associated with pyrite. Grunerite/Ca-amphibole + stilpnomelane and sparse pyrrhotite and pyrite characterize weakly mineralized iron formation. Within adjacent ultramafic rocks, metasomatic reactions yielded assemblages of interlayered Ca-amphibole + biotite, and talc + Ca-amphibole + carbonate + biotite. K-Ar geochronology on metasomatic biotite from mineralized BIF yielded a 1791 ± 32 Ma age.An epigenetic model is favored for the emplacement of gold. The age of the gold mineralization in the Third Portage Lake area is uncertain, but may be Proterozoic based on the preliminary isotopic age and by analogy with Proterozoic gold deposits elsewhere in this part of the Churchill Structural Province."

Jan 1, 1996

By Solar D. Andrés

Several large open pit mines are facing the challenge to design and plan an underground transition to sustain the long term future of their operations. The desired underground method is Block Cave since its natural high productivity and low operating cost that could compete against the open pit cost to mine the final open pit pushbacks. It has been found at several operations where this transition is taking place that the pit limit at which transition is performed is rather deep. This aims to think that perhaps several transition projects have started late in the life of an operation producing an over stress in the transition project and reducing the flexibility in the design of the overall infrastructure and a substantial lost in the complete project NPV. Traditionally the approach to plan open pit underground transition consists of sequentially deciding the final pit using a Lerchs and Grossman type of optimization to find the overall maximum pit shell and then running block cave simulations to find the best footprint for the underground option. The research summarized in this paper is related to the development of an integer linear programming model that aims to compute simultaneously the maximum NPV of the combined option final limit open pit and block cave underground footprint. The model has been tested using two large block models representing two of the current operations in the process of transiting from open pit to underground operations. Finally, the integrated open pit underground transition model is going to be compared to the traditional sequential approach in order to define which method achieves the best NPV. The paper illustrates both case studies in depth.

Oct 1, 2009

By R. S. James, S. P. Goff, A. E. Armitage

"Oxide-facies banded iron formation in the Third Portage Lake area is hosted by ultramafic and calc-alkaline volcanic rocks and related sedimentary rocks of the Archean (2.8 Ga) Woodburn Lake Group, 80 km north of Baker Lake. These rocks record at least two phases of metamorphism/ metasomatism. Greenschist facies metamorphism, in the temperature range of 370°C to 520°C and at pressures above 2.3 kbar, has affected all rocks on a regional scale. Later mineralization and alteration of banded iron formation (BIF) and associated volcanic rocks resulted from metasomatic fluids which carried Mg, K, Ca, S, As, Cu and Au. These fluids were confined to ductile to brittle, cross-cutting and layer-parallel micro-shears developed in the thickened hinge region of a shallow plunging recumbent fold. Metasomatic reactions yielded cummingtonite + biotite-bearing assemblages which are associated with strongly mineralized iron formation. Pyrrhotite is the dominant sulfide phase and occurs within ductily deformed iron formation where it pervasively replaces magnetite. Minor fine-grained chalcopyrite and arsenopyrite generally occur as inclusions within pyrrhotite and recrystallized magnetite, and rarely as individual grains. Pyrite is restricted to brittlely deformed iron formation, and to the contact between iron formation and altered ultramafic rocks, where it is associated with quartz veins. Pyrite typically replaces pyrrhotite. Native gold is associated with both pyrrhotite and pyrite, but higher gold concentrations are associated with pyrite. Grunerite/Ca-amphibole + stilpnomelane and sparse pyrrhotite and pyrite characterize weakly mineralized iron formation. Within adjacent ultramafic rocks, metasomatic reactions yielded assemblages of interlayered Ca-amphibole + biotite, and talc + Ca-amphibole + carbonate + biotite. K-Ar geochronology on metasomatic biotite from mineralized BIF yielded a 1791 ± 32 Ma age.An epigenetic model is favored for the emplacement of gold. The age of the gold mineralization in the Third Portage Lake area is uncertain, but may be Proterozoic based on the preliminary isotopic age and by analogy with Proterozoic gold deposits elsewhere in this part of the Churchill Structural Province. Copyright"

Jan 1, 1996

By John C. Robbins

A new technique for the determination of trace levels of uranium in solution has been developed. A compact laser emits short, but intense, ultraviolet pulses to excite the green fluorescence of a uranyl-complex formed by the addition of a proprietary reagent to the sample. Organic species present in most natural waters also fluoresce quite intensely, but their emission does not last appreciably longer than the excitation pulse, in contrast to the relatively long persistence of the uranyl fluorescence . Electronic 'gating' is employed to separate the long-lived contribution, rejecting substantially the organic emission. Results using the laser fluorescence method on many sets of natural waters of various origins have been compared against corresponding values generated by independent laboratories. Correlation has been generally good over a range from less than 0.1 to more than 100 ppb U. Solid samples have also been analyzed after extraction of the uranium into solution. Accuracies adequate for most exploration purposes have been achieved, but further work is required to determine effects of interferences in samples with complex matrices. The transport and deposition of uranium in natural waters is controlled by the organic and inorganic chemistry of the waters involved. It is suggested that interpretation of very low uranium levels will be aided by additional measurements of conductivity and organic content, with subsequent statistical treatment.

Jan 1, 1978

By J. -C. Parisien-La Salle, D. Blais, G. P. Demopoulos

"In this work the dissolution, precipitation and adsorption behaviour of gold in acidic iron sulphate media containing small amounts of chloride ions is investigated via batch laboratory tests and OLI thermodynamic calculations over the temperature range 25-250°C. Chloride ions may be present in industrial pressure oxidation/pressure leaching (POX/PL) operations due to elevated water salinity levels or due to intentional addition as is the case of the CESL Copper Pressure Leaching Process. Thermodynamic calculations show that AuCl4 - may form depending on the free Cl-/Au ratio and temperature, its stability increasing with increasing Cl- concentration and decreasing with increasing temperature. On the other hand during POX/PL, we know that massive precipitation of iron in various hydrolysis products and compounds occurs. Hence of interest is the question how AuCl4 - that may form during leaching interacts with the iron precipitation products. Gold(III) chloride was found to co-precipitate with iron(III) (oxy) hydroxides and arsenates forming in the autoclave but not with natrojarosite. Upon further investigation it was discovered that activated carbon added in the autoclave (as done in CIL) acts as preferential sink for the mobilized gold, hence opening the potential for the development of a direct cyanide-free gold recovery process in acidic sulphate leach reactors.INTRODUCTIONThe recovery of gold from ores and concentrates has evolved over the years with processing routes becoming increasingly complex. Given the high value of gold, any reduction in losses during recovery operations constitutes an important economic benefit. One such loss that needs to be addressed is the potential solubilisation of gold during pressure oxidation (POX) of refractory sulphidic gold feedstocks. For example, Agnico Eagle Mines reported a loss in gold recovery due to the formation of a gold chloride complex (Garofalo, 2009). Gold is known to form complexes in solution, such as gold(III) chloride, if an excess of chloride ions are present. The fate of such soluble gold chloride during pressure oxidation and the subsequent neutralization of the acidic discharge slurry will determine if gold is lost or recovered in the downstream cyanidation operation. Thus it is of interest to know under what conditions gold chloride may stay soluble or co-precipitate along primary (formed in the autoclave) or secondary (formed during neutralization) precipitates. Furthermore, the mode of co-precipitated gold, such as adsorption on iron compounds, like goethite and hematite (Machesky et al., 1990; Nachayev, 1984); substitution in one of the precipitated phases; or finally chemical reduction to metallic state would have consequences in terms of gold recovery."

Jan 1, 2012

By A. B. Carino

Gulf Minerals (Canada) Limited's Rabbit Lake uranium operation is located in the northern portion of Saskatchewan, 198 miles southeast of Uranium City and /34 miles northwest of Lynn Lake, Manitoba. The paper follows the ore flow through crushing, grinding, sulphuric acid leaching, countercurrent decantation, solvent extraction, ammonium diuranate precipitation, thickening, drying and tailing neutralization.

Jan 1, 1979

By G. R. Tostengard

"The paper identifies functional areas which frequently can yield significant productivity improvement. Emphasis is placed on the repair and maintenance, material supply and training functions. Successful approaches are discussed in some detail, and typical results which have been achieved are reviewed.IntroductionA challenge which at all times confronts the manager o f any mineral operation is the potential to improve his operation no matter how effective it might be a t the present time. The challenge has been present through my entire lifetime and I suspect a good many years prior to that and, I expect, will continue many year s and decades in the future. The competitive and economic situation in which we in the minerals industry find ourselves today makes the challenge eve n more important during the 1980s. In many cases it’s a question of survival, not simply pr of it improvement.There are, of course, many avenues to improving profitability; technological changes, new equipment and facilities, improved products, improved mine plans, etc. All of these are important and must be addressed by each manager. This paper focusses on just one avenue to improvement and that is ""improved management"", not so much of management at the boardroom level but of improved management o f the facilities and workforce as the y currently exist. Management implies control. There are three areas where control is often found lacking:1, Repair and maintenance of equipment and facilities;2. Material supply including procurement, inventory control and warehousing; and3. Training.These three areas are all complex and difficult to manage and they are all but ignored in the formal education which our industry's manager s normally receive. They are areas which can be improved with relatively small investments and therefore, they represent especially attractive improvement targets during the 80s when, for most of us, investment dollars are very difficult to come by."

Jan 1, 1983

By J. A. Brown, F. P. Kerr, M. A. Archer

Extensive testwork on Global Atomic’s Dasa Project in Niger has been conducted at SGS Minerals laboratory in Lakefield, Ontario. Much of this testwork has focused on a two-stage counter-current leach as a means of improving leach efficiency and decreasing reagent consumption. The ore contains uranium mineralization requiring relatively high sulphuric acid concentrations during leaching to achieve acceptably high extractions. Excess free acidity in the leach solution may be utilized by recycling the high acid solution and contacting it with fresh ground ore. The resulting pregnant leach solution (PLS), now higher in uranium concentration and depleted in free acid, is forwarded on to uranium recovery by solvent extraction. The first stage residue proceeds to the second stage leach where fresh acid and oxidant are provided to leach the remaining uranium. This paper presents the results of the testwork conducted on both a Master Composite and Variability samples.

Jan 1, 2020

By A. Ojaghi, A. R. Mohammadi

"The Marvast monazite deposit is located 35 kilometres south - southwest of Marvast in Yazd province of Iran. A representative sample weighing approximately 10 tons was prepared to study the amenability of the ore to physical beneficiation. The size fraction of +1000 µm was removed due to low monazite content and the –1000 µm size fraction was concentrated by the gravity-classification-magnetic methods. According to the results of sample characterization, the representative sample contains 220 ppm REO that is contained in monazite. It was concentrated to 41.5% REO by the above mentioned methods. The recovery of REO in the monazite concentrate was 41.5%.INTRODUCTIONRare earth elements are critical metals in many countries (Gupta, 2005; UK Geological Survey, 2011). Increasing application of these metals in hi-tech industries and price fluctuation caused by Chinese production policy has led other countries to focus on their local resources (UK Geological Survey, 2011). In this case, Iran is not an exception.REE mineralization in Iran is mainly located in the central zone. Regarding the exploration data, these deposits are divided into two categories. The first group is iron ore deposits in which the REE are carried by phosphate minerals. The other group is placer deposits where monazite is the major mineral of the deposit. The Marvast placer deposit is one of these types of deposit (Daliran, 1990; Mokhtari, 2008; Torab, &Lehmann, 2007; Alipour, 2014)."

Jan 1, 2016

By James F. Archibald

A research effort has been undertaken, under WSIB sponsorship, to characterize the support capabilities of conventional and innovative spray-on lining materials for mitigating dynamic failure effects created by simulated rockbursts. Conventional spray support media, such as shotcrete and fibrecrete linings, and a variety of new spray-on lining materials (TSL?s), typically polymer-type thin coatings, were subjected to simulated rockburst influence. For baseline comparison, conventional rockbolt and boltand- mesh support products were also evaluated. Observation of lining performance was undertaken through completion of field scale support and rock detonation trials. Controlled blasting tests were conducted at the Queen?s University Explosives Laboratory to examine the effectiveness of the variety of surface coating agents for modifying dynamic rock spalling processes. All tests were performed upon largely undisturbed and homogeneous rock materials in highly repeatable fashion. Both conventional and innovative TSL-type surface lining materials were subjected to ?rockburst? exposure in rigorously-controlled blast trials. All blasts were observed seismically and photographically to provide detailed information concerning rock motion, surface fracturing, ejected fragment motion and support liner survivability characteristics. These material comparison trials were performed to assess the relative effectiveness of a wide range of currently-available area support techniques for suppressing hazards associated with dynamic rock ejection. The results of this study validates that thin, sprayon linings may be equally as effective, and often better, than conventional support materials at mitigating rockburst or like damage in highly stressed mine environments.

May 1, 2003

By W. A. Jones

THE estimation of the average value of gold ore involves many considerations, among them the correct sampling of the deposit, the dilution by waste, and the loss of high-grade fines. It is a common experience that, after all these factors have been evaluated, adjustment of the assays is necessary before satisfactory agreement between the calculated mine grade and the mill heads is obtained. In fact, at many mines the latter correction overshadows all others in the preparation of routine estimates. For this reason it is proposed to deal only with the mathematical treatment of mine assays and the problem of bringing estimates into conformity with the corrected mill heads. Mine assays differ from physical measurements because the range of values is very great and these are not symmetrically distributed above and below the average, there being fewer high than low results. There is no widely accepted mathematical procedure for determining the average of series of measurements which exhibit these characteristics. Customary practice consists in empirically reducing high assays until a satisfactory agreement with mill heads is reached. It was thought that more confidence could be placed in grade estimates if a logical basis for calculations could be devised .. In an attempt to find a fundamentally sound procedure, amenable to practical application, many series of assays comprising over 235,000 channel samples (1) were studied at Hollinger Consolidated Gold Mines, Limited. Such an investigation could only be made where records covering many years of operation are available and where tabulating and calculating machines are in use. The results are recorded in the hope that the relationships noted for the large groups of assays used are of fundamental character and that the data will be useful to others dealing with the problem of grade estimation.

Jan 1, 1943

By Allan A. Este, Bruce Arthur

"Rio Algom's Stanleigh Mine and Mill Operation Was' officially started up in August 1983. In September 1982, Rio Algom contracted Estonix International Inc. from Lively, Ontario, to develop and implement two innovative programs: (1) Work Renovation Planning, and (2) Systems Performance Training. This paper deals with the development and implementation of these two concepts relative to the plants technology from start-up to present and the exceptional results achieved. This paper discusses how a small but motivated workforce resulted in the smooth transition from startup to full production. It also deals with how these concepts were applied elsewhere in the organization which permitted a successful transition and downsizing of the over-all operation.IntroductionRio Algom Limited produces uranium in Elliot Lake, Ontario. In the late 1970s Rio Algom entered a contract with Ontario Hydro to supply uranium from its Stanleigh property, which had been idle since 1960. The mine was subsequently upgraded, and a new modem mill was designed and built, commencing operation in 1983.From then until September 1990,Rio Algom had three producing mines and mills in the Elliot Lake area. Quirke mill, with a capacity of 6350 tonnes per day, operated continuously from 1968. The Panel mill with a 3000 tonnes per day capacity, operated since 1979. Stanleigh mill continues to operate under long-term contracts, although at a production rate about 25070 lower than its rated capacity of 5000 tonnes per day.Both the Quirke and Panel mills, although not entirely similar, were conventional uranium mills utilizing crushing, grinding, leaching and ion exchange. As such, and in keeping with the traditional management style, there was a rather large mill operating workforce, which utilized a line-of-progression job classification system."

Jan 1, 1993

By G. J. Kipouros, W. Judge

"The prevalent metal extraction processes for most reactive metals are fused salt electrolysis and metallothermic reduction. The feed material for both of these processes is the anhydrous chloride of the metal under consideration. Dehydration of the feed material is then a critical step in the production of most reactive metals and requires rigorous thermodynamic analysis. Thermodynamic data for most of the reactive metal chloride hydrates have not been measured. Improper dehydration of the metal chloride may lead to a prohibitive amount of hydroxychloride, oxychloride, and oxide. To prevent hydrolysis a certain pressure of hydrogen chloride is required. An estimation and prediction model is presented for the vapour pressures of reactive metal chloride hydrates in an attempt to deduce the conditions necessary for dehydration to proceed without hydrolysis. Thermodynamic data including heat capacities, standard entropies, and standard enthalpies are estimated/predicted for all conceivable intermediate hydrate compounds. Estimations are based on published data as well as trends proven in similar systems. The thermodynamic estimations and predictions are presented for the magnesium, neodymium, praseodymium, and dysprosium chloride hydrates. INTRODUCTIONThe high reactivity of metals such as the alkalis, alkaline earths, and lanthanides prevents their reduction by traditional pyro- or hydrometallurgy. In their elemental form, these metals are raw materials in the manufacture of intermediate products such as alloys and electronic components. Currently the only two viable metal production methods are fused salt electrolysis and metallothermic reduction. Various feed materials have been proposed for these processes. Using the chloride of the metal as a feed material offers advantages in separation and purity of the final product, as well as lower energy input. Chlorides, however, are hygroscopic and must be dehydrated before use. Improper dehydration will lead to a prohibitive amount of oxychloride which will lower efficiencies and contaminate the final product.Optimum conditions for proper dehydration of MgCl2•6H2O to produce pure MgCl2 without hydrolysis have been calculated from existent thermodynamic data and have been reported previously (Kipouros, 1987; 2001). Calculations were also performed for the case of production of pure anhydrous NdCl3 from NdCl3•6H2O (Roy, 1997)] and the mechanism of dehydration was elucidated. Some thermodynamic studies on the dehydration of chlorides of the rare earths have also been conducted (Sundstrom, 1997; Hong, 1997; Aschcroft, 1968; Haeseler, 1965; Ukraintseya, 1989)."

Jan 1, 2012

By B. R. Hart, S. S. Dimov, J. Fournier

Carbonaceous matter (c-matter) in sulphide ores can adversely affect the process of gold recovery during cyanidation due to its ability to adsorb, or preg-rob, gold from a cyanide leach solution. This paper describes a standardized procedure for characterization of c-matter in an ore sample providing detailed information on its composition, maturity and preg-robbing capacity. The procedure utilizes the following complementary analytical techniques in conjunction with several chemical tests and assays: SEM/EDX Raman spectroscopy and TOF-SIMS. Results of the test can be used as a predictive tool to estimate the impact the c-matter will have on the gold recovery process. A comparison between predicted preg-robbing behaviour and cyanidation test results are presented.

Jan 1, 2011

By M. Cossette, P. C. A?tcin

At present there is considerable confusion in the asbestos industry with regard to density and porosity measurements of asbestos. In order to clarify the situation, various notions of porosity and density are defined by means of simple schemes and clear symbols are proposed to denote them. An experimental procedure is then preposed and outlined, which is based upon Archimedes' principle. Experimental conditions at each stage of the method are explained clearly in order to minimize the opportunity for errors. Finally, the results of a study on the porosity and density of asbestos minerals having various characteristics are presented.

Jan 1, 1972

By W. G. Worcester

Generally speaking, the term 'clay' appears to convey but little to the average layman other than of a sticky substance to be rigidly avoided when making a cross-country drive in the family ark- especially so if the chains have been left behind. On the other hand, the technical ceramic; engineer, though his chariot be bogged in the self-same mud-holes, will, more than likely, be planning on ways and means for the conversion of the troublesome gumbo into paving bricks over which all might ride with pleasure and security. However, to come to the point, the term 'clay' bears much the same relation to the ceramic world that the term 'ore' does to the metallurgical; in other words, as there are many kinds of ores, so also are there many kinds of clays, and it therefore becomes necessary to classify and sub-classify them previous to a discussion of their relative values and importance. Hence, a brief digression will be made from the main topic of this paper in order to enumerate and classify a number of the more important types of clays. By so doing, the relative position of Saskatchewan clays, later discussed, will be better understood.

Jan 1, 1929

By A. Valdivieso

Reducing accident rates keeps getting more and more complex as the usual tools enter a curve of diminishing results. Fortunately, nothing modifies behaviour in a stronger and wider way than having a robust safety culture. On the other hand, managing cultural change is difficult and the risk of back-fire is very high, especially if the workforce does not trust our intentions. A personalized approach of well chosen and targeted actions tends to be the only yet difficult option. We have found, via experience in the metallurgy and chemistry industries, a way of preparing the company and the workforce to accept these sorts of culture changing measures faster and easier. Using company-wide changes based on workplace perception, yields the most optimal acceptance. It is based in the principle that we all use clues in our environment as guides to choose our behaviour. So, controlling the perception that our workplace generates can affect behaviour and simplify our task before it even starts. It is a matter of using the tools that other disciplines such as marketing, social engineering and architecture bring to us and adapting them to a very defined objective: Having our installations “sell” safety so that our people unconsciously believe that they must adapt to safety values in order to “do well” in said environment. INTRODUCTION After decades of improvements in accident rates, we are understandably hitting a diminishing results curve: most actions that spectacularly reduced accidents in the past (e.g., Innovation in Personal Protection equipment, adapting international standards and legislation, and innovative safety programs; Figure 1) now hardly get us the exponential gains we saw years back, regardless of the investment we put on them. Furthermore, the improvements in safety of the last 3 decades have been creating new sets of issues that start to show their face such as: By reducing accidents we can create feelings of invulnerability as we lose view of the consequences. With innovative protection equipment we increase Risk Homeostasis, meaning that people behave in a more dangerous way in order to maintain a constant level of risk in their lives (Getting closer to fire after getting better fire-proof garments for example). Too much Legislation can create a feeling of disengagement from personal responsibility. And despite improvements, we haven’t really solved the production vs safety confrontation, it is now stigmatized and less visible, yet it tends to reappear in moments of weakness.

Jan 1, 2019

By H. J. McQueen

Large-scale industrial production of pipe began with longitudinal hot pressure welding of wrought iron by passage of skelp (narrow strip with beveled edges) through a die or bell that curled it about a longitudinal axis until the edges were forced together. Such small to medium tubes could be reduced by rolling or drawing; with threaded connections, they were excellent for distribution of clean water and of illuminating gas for street, home and industrial lighting. Although steel lacks the fluxing slag for pressure welding it has hot strength similar to iron; hot-pressure bell welding was advantageously transferred to steel in long coiled strip with 50% higher cold strength. For pipe without weld-line defects, hot cupping followed by Pilger mill rolling produced tubing that revolutionized bicycle quality and high-pressure service for boilers and chemical processing. Mannesman hot rotary piercing produced long thick walled tube that permitted reduction or expansion by rolling to provide pipe sections up to 60 cm diameter and 12 m long. During 1910 - 1940, oil and gas pipeline technologies, notably welding evolved markedly as they proliferated in the United States, in response to far-flung petroleum fields, expanding industry consumption and the automobile revolution. In the Second World War combat pipelines were laid rapidly, such as: the Canol line through the Yukon to Alaska, and fuel supply lines across the channel and through liberated France. Perfection of welding techniques for both longitudinal and spiral weld large diameter pipe in combination with controlled-rolling of micro-alloyed steels made possible reliable Arctic pipelines. The development of pipe production and utilization in Canada is recounted. The fabrication techniques and metallurgical controls are explained.

Jan 1, 2005

By C. Tasker

Introduction In the Early part of 1930 the Ontario Research Foundation was asked by the Minister of Mines, the Hon. Charles McCrea, K.C., M.P.P., to undertake a technical and economic investigation of the Northern Ontario lignite deposit. This investigation has been under way since June, 1930, and has necessitated considerable work at the deposit, in the laboratories of the Foundation, and at test plants in Europe. All the work has been carried out in active co-operation with the Provincial Department of Mines, the Deputy Minister, Mr. T. F. Sutherland, and several of his technical colleagues being associated with members of the staff of the Foundation on the Advisory Committee, which has met at frequent intervals to co-ordinate and direct the various lines of research. An interim report was made to the Minister of Mines by the Director of the Foundation, Dr. H. B. Speakman, at the end of December, 1932, and is at present under consideration by the Minister. This report deals with the extent and character of the deposit, the methods and costs of mining, and the methods and costs of processing raw lignite, the characteristics of certain lignite products, and the technology and economics of present fuel utilization by railways, industry, and domestic users in northern Ontario. It is not the purpose of the author to discuss in this paper either the geology of the deposit or the economics of the mining, processing, and utilization of lignite, but rather to deal briefly with some of the technical problems investigated by the Foundation during the study of the characteristics and methods of utilization of Northern Ontario lignite. Some mention, however, of the work carried out to define the extent of the deposit is a prerequisite to any discussion of the nature of the lignite.

Jan 1, 1933

By John Blackshaw

NEW sources of supply of tungsten concentrates became necessary when the flow from the Far East was blocked in 1942. In Canada, one source has been noted in the workings of the Hollinger mine at Timmins, Ontario. For many years, a small amount of scheelite had been removed with the gold ore, and an appreciable tonnage of scheelite still remained in the mine. At the request of the Dominion Government, a plant was built to recover this scheelite in the form of a concentrate that could be used by the alloy-steel industry without further preparation. The plant began operating early in March, 1942, and a small tonnage of ore, carrying scheelite and gold values, has been treated daily since then. The possibility of recovering the scheelite had been considered on several previous occasions. Each time the proposal had been given up because the total profits from the enterprise were estimated to be insufficient to repay the capital cost of building the recovery plant. At the time the plant was built, additional information had been gathered about the tonnage and grade of the scheelite ore in the mine, and several thousand tons of ore grading higher than 0. 25 per cent WO3 (tungstic trioxide) were known to be available.

Jan 1, 1943