Search Documents

By H. C. Cooke

Geological examination of the underground workings of the Horne and Aldermac mines during the summer of 1927 has brought out the following facts: (1) That the ores tend to replace bodies of breccia or tuff rather than massive lava or dyke material; (2) That the faulting and folding at the Horne has had a pronounced effect in localizing the ore-bodies; (3) That there is a tendency in cert?-in cases for ore-bodies to be localized beneath gently dipping dykes, which acted as impervious roofs; (4) That there is a great difference in age between the chalcopyrite part of the ore-bodies and the pyrite-pyrrhotite portion. A statement of the development to date at the Aldermac mine is also included in the paper. ALDERMAC MINE The Aldermac property is made up of eight claims in the western half of Boischatel township, Quebec, including 747 acres in all. The mine itself is approximately three miles, 25 chains from the west boundary, and four miles, 55 chains from the north boundary, of the township.

Jan 1, 1928

By X. Q. Jiang, D. L. Chen, A. Macwan

Magnesium alloy, being the lightest structural material, is a key candidate for the weight reduction of vehicles in automotive and aerospace industries; however, its poor corrosion resistance and difficulty in deformation are limiting factors. Recently, Al/Mg/Al tri-layered clad sheets have been considered as a promising alternative to improve corrosion resistance and formability of magnesium alloys. The aim of this study was to evaluate the tensile properties and deformation behavior of Al/Mg/Al tri-layer clad sheets at different temperatures and strain rates. Yield strength (YS), ultimate tensile strength (UTS), and elongation were observed to increase with increasing strain rate. With increasing temperature from -40°C to 180°C, YS and UTS decreased and ductility increased. The strain hardening exponent evaluated via three equations of Hollomon, Swift, and Afrin et al. showed a similar increase with increasing strain rate and decreasing temperature. The fractographic analysis showed partial debonding of clad interface especially at higher strain rates and lower temperatures.

Jan 1, 2015

By Simon C. Dominy, Alwyn E. Annels, Paul Wheeler, Suzanne P. Barr, G. Simon Camm

Narrow veins are an important world-wide source of silver, tin, uranium and particularly gold. To potential ?nanciers, this style of mineralization is viewed as high risk because of the often relatively small resource involved and high cost of estimation. In many cases diamond core drilling will not enable resource estimation beyond the inferred and indicated categories. Exploratory under-ground development is required to de?ne measured resources. The de?nition of geological and grade continuity are major factors in narrow vein assessment. A measured resource must be based on strong geological and grade continuities. Narrow veins, generally less than 3 m wide, are complex geological phenomena, which commonly display unpredictable geometry and grade distribution. Variations in structural continuity, dip, strike, width, mineralogy and speci?c gravity are common. Veins may be composite, with ore-grade mineralization restricted to a speci?c structural domain. Branches, intersections and braided zones are common features. Potentially high-grade zones are often localized within ore shoots, which are surrounded by barren/low-grade regions. Resources must be determined as closely as possible to reality and re?ect the distribution of the commodity in the rock. Estimation has three main requirements: (1) geological study to determine orebody nature;(2) estimation of tonnage and grade, and (3) the presentation of this information using a classi?cation that is clear, unambiguous and bankable. Estimation methods employed are either classical or geostatistical; however, classical methods are often used because of the dif?culties in applying geo-statistics. Grades generally show a strong positively skewed distribution testifying the presence of high-grade values. Problems exist in the applicability of cutting outlier values risking over- or under-estimation of grade. It is generally believed that where resource estimates are in error, poor geological control is usually the cause. Overestimation can lead to the closure of a mine through lost revenue and capital. An understated estimate can result in an opportunity missed for pro?t and/or greater economies of scale. De?nition of reserves involves the consideration of economic and engineering data, to decide which part of the resource is economically mineable. Geology plays a similarly important role at this stage in the assessment of likely mining method, dilution, recovery etc. Throughout resource/reserve estimation, it is crucial that the amount and quality of the data and the geologist’s experience are relevant. The impact of geological understanding on estimation is often undervalued or assumed to be of lesser importance than ?nding grades and tonnages. This paper discusses the geology of narrow vein deposits and the importance of geology in their evaluation.

Jan 1, 1997

Access to accurate real-time information is critical to maintaining efficiency and competitiveness in any modern minerals processing facility. At MMG LXML Sepon Copper Operation in Lao P.D.R., controlling the copper grade of the feed to the leaching circuit is paramount for maximising productivity and copper recovery. Since 2008, real-time analysis data has been available to process engineers from the Geoscan on-belt analyser installed on the Copper Mill feed conveyor. Access to accurate real-time results from the Geoscan has allowed the process engineers to strictly control blending based on copper grade to overcome variability in the plant feed, where conventional sampling and laboratory analysis is difficult, error prone and time consuming. In addition to enjoying these benefits since the Geoscan’s installation, in recent times the process engineers have expanded the use of the Geoscan by observing elemental results other than copper grade to control different aspects of the operation, focussing on the reduction of Gangue Acid Consumption. This paper discusses the process of expanding the Geoscan use at the operation, including an explanation of the calibration process. Additionally, a brief description of the Geoscan and its use at MMG LXML Sepon Copper Operation is provided, as well as a summary of recent calibration and analysis results. A discussion of future works concludes the paper.

Jan 1, 2016

By S. R. McCutcheon, D. R. Lentz, W. S. Downey

"Abstract - The Little Falls member of the Nepisiguit Falls Formation is situated in the northern part of the Brunswick Belt of the Bathurst Mining Camp and has been interpreted as the distal equivalent of proximal tuffaceous rocks that host the stratiform Brunswick No. 12 and No. 6 Pb-Zn massive sulfide deposits. It comprises fine-grained, greenish-gray tuffaceous sandstone in the lower part, and coarse-grained, crystal-rich tuffaceous sandstone in the upper part. Petrographic evidence suggests that these rocks have a turbiditic origin. The Little Falls member is underlain by the Vallée Lourdes member, mainly composed of relatively shallow-water calcareous rocks, and is conformably overlain by Mn-rich sedimentary rocks, mainly red argillites that host the Tetagouche Falls Mn-(Fe) deposit. All these rocks are considered to belong to the Nepisiguit Falls Formation, part of the Ordovician Tetagouche Group. Whole-rock geochemical data from the fine-grained tuffaceous sandstone and coarse-grained tuffaceous sandstone indicate that the two units of the Little Falls member are distinct. Zr and TiO2 contents, and total rare earth element (REE) values are higher in the coarse-grained unit (average Zr/TiO2 = 0.040, average SREE = 247 ppm, n = 6) than in the fine-grained unit (average Zr/TiO2 = 0.048, average SREE = 158 ppm, n = 17), which can be attributed to the variation in crystal content between the two units. Both units are HREE-enriched and have elevated La/Yb relative to the typical Nepisiguit Falls Formation. Overall, the geochemical data combined with evidence from the bounding units suggest that the Little Falls member was deposited in relatively shallow water, possibly in a near-arc environment. The relationship of volcanic facies within the Nepisiguit Falls Formation and the geochemistry of these facies indicate strongly that fine grained, reworked tuffaceous rocks, regardless of whether they are the distal equivalents of proximal tuffaceous rocks, are not associated with the major ore-bearing horizons of the Bathurst Mining Camp. Sommaire - Le Membre de Little Falls de la Formation de Nepisiguit Falls se retrouve dans la partie nord de la Ceinture Brunswick du Camp Minier de Bathurst ou elle a été interprétée comme l’équivalent distal des roches tuffacées proximales hôtes des gisements de sulfures massifs de Pb-Zn stratiformes Brunswick No.12 et No.6. Il consiste en grès tuffacé à grains fins gris verdâtre dans sa partie inférieure et en grès tuffacé à grains grossiers riche en cristaux dans sa partie supérieure. Les données pétrographiques suggèrent que ces roches ont été déposées par des courants de turbidité. Le Membre de Little Falls repose sur le Membre de Vallée Lourdes, lequel consiste principalement en roches calcareuses déposées en eau relativement peu profonde; il est de plus recouvert en concordance par des roches sédimentaires manganifères, lesquelles consistent principalement en argilites rouges hôtes du gisement de Mn-(Fe) de Tetagouche Falls. Toutes ces roches appartiennent à la Formation de Nepisiguit Falls, laquelle fait partie du Groupe de Tetagouche, d’âge Ordovicien. Les données lithogéochimiques des grès tuffacés à grains fins et à grains grossiers indiquent que ces deux unités du Membre de Little Falls sont distinctes. Les teneurs en Zr et en TiO2, ainsi que la teneur totale en Éléments des Terres Rares (ÉTR) sont plus élevées dans l’unité à grains grossiers (Zr/TiO2 moyen = 0.040, SREE moyen = 247 ppm, n = 6) que dans l’unité à grains fins (Zr/TiO2 moyen = 0.048, SREE moyen = 158 ppm, n = 17), ce qui pourrait s’expliquer par la variation de la quantité de cristaux dans chacune de ces deux unités. Chacune de ces deux unités présente un enrichissement en ÉTRL ainsi qu’un rapport La/Yb relativement plus grand que ce qui est typiquement observé dans la Formation de Nepisiguit Falls. Les données géochimiques considérées conjointement à l’information provenant des unités adjacentes suggèrent que le Me"

Jan 1, 2006

By Simon C. Dominy, Alwyn E. Annels, Paul Wheeler, Suzanne P. Barr, G. Simon Camm

Abstract-Narrow veins are an important world-wide source of silver, tin, uranium and particularly gold. To potential financiers, this style of mineralization is viewed as high risk because of the often relatively small resource involved and high cost of estimation. In many cases diamond core drilling will not enable resource estimation beyond the inferred and indicated categories. Exploratory underground development is required to define measured resources. The definition of geological and grade continuity are major factors in narrow vein assessment. A measured resource must be based on strong geological and grade continuities. Narrow veins, generally less than 3 m wide, are complex geological phenomena, which commonly display unpredictable geometry and grade distribution. Variations in structural continuity, dip, strike, width, mineralogy and specific gravity are common. Veins may be composite, with ore-grade mineralization restricted to a specific structural domain. Branches, intersections and braided zones are common features. Potentially high-grade zones are often localized within ore shoots, which are surrounded by barren/low-grade regions. Resources must be determined as closely as possible to reality and reflect the distribution of the commodity in the rock. Estimation has three main requirements: (1) geological study to determine orebody nature; (2) estimation of tonnage and grade, and (3) the presentation of this information using a classification that is clear, unambiguous and bankable. Estimation methods employed are either classical or geostatistical; however, classical methods are often used because of the difficulties in applying geostatistics. Grades generally show a strong positively skewed distribution testifying the presence of high-grade values. Problems exist in the applicability of cutting outlier values risking over- or underestimation of grade. It is generally believed that where resource estimates are in error, poor geological control is usually the cause. Overestimation can lead to the closure of a mine through lost revenue and capital. An understated estimate can result in an opportunity missed for profit and/or greater economies of scale. Definition of reserves involves the consideration of economic and engineering data, to decide which part of the resource is economically mineable. Geology plays a similarly important role at this stage in the assessment of likely mining method, dilution, recovery etc. Throughout resource/reserve estimation, it is crucial that the amount and quality of the data and the geologist’s experience are relevant. The impact of geological understanding on estimation is often undervalued or assumed to be of lesser importance than finding grades and tonnages. This paper discusses the geology of narrow vein deposits and the importance of geology in their evaluation.

Jan 1, 1997

By H. P. Pew

THE Pembina oil field is in west-central Alberta, about 88 miles west-southwest of Edmonton. The field, about 35 miles long by T HE Pembina oil field is in west-central Alberta, about 88 miles west-southwest of Edmonton. The field, about 35 miles long by 85 miles wide, is the largest in Canada in areal extent, in the amount of oil in place and in the current producing rate. The discovery well was completed in the middle of 1953. The field has grown until its present area is 369,820 acres. There are 74 working interest owners in the field. Early in the producing history of the Pembina field a committee of operators was formed on a permanent basis. The Pembina Operators' Committee has established a permanent staff, which compiles and distributes pertinent field information on a regular basis to all participants. The Alberta Oil and Gas Conservation Board has dealt with field-wide problems primarily through this committee. Expansion of the field was rapid as shown by the number of wells completed -from 135

Jan 1, 1961

By Joel Werner

Weak metal prices, declining head grade, and increased operational costs are forcing many open pit mining companies to look to their balance sheets for significant cost reductions in order to remain competitive. Maintenance continues to represent a significant proportion of the total operating costs in the mining industry. Compared with the other major cost components of the mining process very little effort has gone into maintenance optimization. The potential payoff from maintenance optimization on the cash cost of the commodity is enormous. A large percentage of these costs are incurred in unscheduled maintenance events, which typically cause serious disruptions to the production process. These maintenance induced production losses can be a significant contributor to the overall operating costs. A structured proactive maintenance approach using the latest advances in technology can achieve dramatic cost reductions and productivity improvements. Remote condition monitoring systems are becoming increasingly commonplace and have the potential to identify problems prior to failure. Detection of equipment degradation prior to failure will enable repairs to be scheduled thereby reducing costs and interruptions to production. Remote condition monitoring technology has evolved rapidly in recent years, with a host of new tools becoming available to assist mine operators in improving their maintenance operations. These tools have capabilities such as: remote real-time vital signs and performance monitoring, alarm/event handling, trend analysis, and maintenance workflow management. When these monitoring tools are used in conjunction with a mine management system the vital signs data can be integrated and associated with maintenance history, predictive maintenance data, operational information, and geographical information. This integrated approach to the management of vital maintenance data will help shift the mobile equipment maintenance paradigm from reactive to proactive. This paper will introduce a proactive approach to the management of the maintenance process and the tools required to facilitate this process.

May 1, 2003

By Yoginder P. Chugh

This paper discusses an ongoing field study in southern Illinois (USA) that focuses on: 1) Identifying mechanisms of instability in the set-up rooms (SR) and their T-junctions with headgate and tailgate entries, 2) Developing alternate 3-entry and 4-entry set-up rooms geometry using 3-D numerical analyses, 3) Implementing developed geometries in cooperation with mining professionals and regulatory agencies, and 4) Demonstrating performance of implemented geometries through field monitoring. Illinois longwall mining operations typically experience ground control problems (roof falls, rib sloughing, floor heave, etc.) within SR layouts and around the T-junctions of SR. These occur around the areas where the SR for adjacent longwall face (to be mined) connect with the SR of the previously mined face, and around the tail-gate entries of the mined-out longwall face and around the T-junctions of SR. The problems manifest as highly fractured immediate roof strata, major shear zones in the roof, horizontal displacements within the excavations that result in shearing off the heads of the bolts, floor heave and severe rib sloughing. Similar observations have also been made in longwall mining in Utah.

Aug 1, 2013

By Dharmendr Kumar, Pradip, Sivakumar Subramanian, Beena Rai, Venugopal Tammishetti

The separation efficiency in a mineral processing plant is generally assessed and reported in terms of elemental assays constituting the minerals of interest. However, different minerals comprising of same elements behave differently under similar process conditions. Thus, it is imperative to track the mineral composition thank elemental composition of different streams in a processing plant. The availability of automated mineral analyzers such as QEMSCAN and TESCAN in recent times has made it possible. However, due to the high cost and expertise required, their adaptation in day to day monitoring of operations is not yet a common place. X-ray diffraction (XRD) profile fitting (Rietveld Refinement) is another technique which can provide estimates of mineral proportions in a sample. The results of Rietveld Refinement however are affected by coating of fines on coarse particles, method of sample preparation, particle size distribution of sample, elemental substitution in mineral crystal lattice. In the present work, we propose a simple and efficient method for quantitative estimation of minerals in iron ores using elemental assays and thermo-gravimetry analysis data. The minerals (hematite, goethite, gibbsite, kaolin and quartz) are identified using powder XRD analysis. It is also observed that goethite contains Al substitution in the crystal lattice. The samples were analyzed for %Fe, %Al2O3 and %Silica using chemical analysis. The measured Loss on Ignition (LOI) in the sample is contributed from goethite, gibbsite and kaolinite phases. LOI from gibbsite and goethite occur in temperature range 250–350°C and LOI from kaolinite occur in temperature range 400–700°C. According, LOI are determined in two different temperature ranges that are 100–400°C and 400–850°C. We have used the data to successfully determine the mineral compositions of iron ore samples. We have also employed a data reconciliation algorithm on the calculated data for further improvement and consistency of our results. Our method is very convenient for quick estimation of mineral proportions in a sample. The proposed method can also be used for quantitative phase estimation in bauxite ores and red muds.

Jan 1, 2016

By Robert G. Boutilier

So far, most social performance monitoring systems have not gone beyond listing the impacts on various stakeholders. Executives have had to rely on intuition to devise interventions that would improve the impacts. This paper describes a survey process, known as the Stakeholder 360 (S360), which eliminates much of the guesswork. The paper reviews key studies showing that raising the levels of communication, trust, and common vision among stakeholders leads to the acquisition of the resources needed to improve the socio-economic situation. Therefore, the Stakeholder 360 measures the levels of these three factors in the relationships between a company and its stakeholders, and among the stakeholders themselves. In a validation study at a gold mine in rural Papua New Guinea, the S360 produced a socio-political ?roadmap? that showed management and stakeholders alike which relationships need more communication, trust, or common goals/vision. Management used the findings to create alliances that helped the government move forward on a regulatory regime for the mine closure. The community used the findings to focus its planning for life after the closure. An S360 survey conducted six months later revealed a decline in dependence on the mine and an overall increase in levels of mutual understanding.

May 1, 2002

By Owsiacki. Leo

Both the 8 and A-C ore zones of the Heath Steele Mine contain extensive areas of brecciated ore. This texturally distinct ore type has been tentatively defined as a fragmental or conglomerate massive sulphide. It consists of subangular and round fragments of pyrite up to 30 em in diameter, smaller quartz clasts and chloritized, mineralized, lithic fragments in a faintly banded matrix of pyrrhotite and chalcopyrite. The chalcopyrite is concentrated in the pressure shadows of the fragments and appears to reflect remobilization and recrystallization during a deformation which postdates the formation of the clasts. A generally conformable relationship with the underlying banded pyrite-sphalerite ore, discordancy with the host banded argillites, spatial distribution and similarity to Kuroko ores suggest that the fragmental ore is of primary origin and that breccia formation is probably due to soft-sediment slumping or sliding initiated by volcanic explosions, as hypothesized for similar massive sulphides in various Japanese mines. It is nevertheless recognized that certain structural features in some clasts may result from deformation preceding the formation of the breccia, and at this stage a tectonic origin cannot be completely eliminated.

Jan 1, 1979

By A Hitchen

A general outline is given for the determination of copper, nickel, cobalt, zinc, lead, cadmium, bismuth, manganese, uranium, molybdenum, vanadium, sulphate and fluoride by polarographic or amperometric methods in a variety of ores or metallurgical products. The detection of oxygen in gas mixtures by an amperometric method used as a safety device is also discussed. Introduction I N this paper, a general outline will be given of the polarographic and amperometric methods used for the chemical analysis of various ores and metallurgical products in the Chemical Analysis Section of the Extraction Metallurgy Division of the Mines Branch. The methods to be discussed will be confined to those based on the use of normal D.C. polarography and will not include those methods which utilize a cathode-ray, square wave, pulse or A.C. type of polarograph. For the sake of convenience, ? the polarographic methods will be discussed according to the type of supporting electrolyte employed, as the same electrolyte may serve to determine more than one element in more than one type of ore. Amperometric methods will be discussed according to the element to be determined rather than

Jan 1, 1965

By C. Pichler, C. Benigni, J. Antrekowitsch

"The recycling of steel mill dust results in zinc oxides which are sold to the primary industry in or-der to recover zinc in its metallic form. Due to the contained impurities - chlorine and fluorine - these sec-ondary oxides are usually charged into the roaster together with primary concentrates. Appearing problems in this furnace limit the application of secondary materials. Based on the zinc amount, a direct leaching, assumed that a low halide concentration is present, would be possible. To use the zinc solution directly in the electrowinning stage, the concentration of impurities, first of all iron, is limited. Iron can be found in secondary zinc oxides due to carry over during the recycling process. In order to reduce the iron content in the solution, the leaching has to be pH-controlled. This leads to a limited number of simple purification steps before the solution enters the electrolysis. Various trials were performed to evaluate the influence of temperature, time and sulphuric acid concentration on the iron dissolution. This paper deals with the results and also focuses on other impurities such as halides. Additionally, the soda washing process, usually done with secondary zinc oxides to remove most of the halides, and the challenges within this step are discussed.INTRODUCTION Recycling of steel mill dust, which is the main zinc containing residue, in the Waelz process dis-plays the common method worldwide. The product of the process is a secondary zinc oxide which is con-taminated with different elements like lead, iron and halides due to mechanical carry over or evaporation. Depending on the feeding material the concentration of each element in the dust is varying. The zinc con-tent of the product, also called Waelz oxide, lies around 65–68%. Based on these values it presents an al-ternative to the primary concentrate for the production of metallic zinc. The contained halides limit the direct utilization in the leaching stage and therefore have to be reduced. State of the art is a soda washing process but also solvent extraction gives a possibility to remove chlorine and fluorine but the desired con-centration for the electrolysis is hardly reachable (Antrekowitsch et al., 2016) Iron is present as an undesirable component of such secondary zinc oxides due to carry over. During the hot acidic leaching of the secondary concentrate, iron is dissolved too. Based on the higher electrical potential iron has to be removed before the zinc solution enters the electrowinning stage. It is usually removed by precipitation as goethite, hematite or jarosite, which is the common precipitation residue (Ismael et al., 2003)."

Jan 1, 2017

By R. J. Mitchell

"The use of hydraulically delivered classified tailings sands to provide ground support in large mining operations is still widespread despite recent developments of alternate backfilling methods and materials. The major disadvantages of the use of hydraulic fill are the costs and risks associated with slurry delivery. The main risk is that of bulkhead failure resulting from sand liquefaction due to insufficient operational control or due to dynamic loading from earthquake or rockburst. That risk may be eliminated by the pouring of a stiff cemented sand plug in the base of each stope prior to continuous fill pouring in that stope. An additional advantage of cemented plugs is that massive bulkheads are not needed. Instead, a temporary (removable and reusable) bulkhead can be used for plug forming.Physical model studies of fill pressures on a temporary bulkhead were carried out in a 3 m radius centrifuge facility. Fill pouring in-flight was carried out in order to model prototype stress paths. The results indicate that the average bulkhead pressure is likely to be less than 10 kPa under normal operating conditions and less than 20 kPa under the poorest anticipated operating conditions which include smooth walls, high slimes content and high water-content slurries. A portable bulkhead consisting of a central core and a surrounding sealing bladder was modelled and found to be effective. The use of different sizes of cores allowed the stress distribution adjacent to these bulkheads to be evaluated."

Jan 1, 1992

By Robert T. McKnight

"Traditional techniques for valuing resource projects companies have been primarily based on discounted cashflow methods (DCF) or by comparison to similar projects with an apparent market capitalization. Many resource projects are really forms of options to invest rather than a future cashflow stream. Employing the DCF method to value a resource project which is really an option to invest, can dramatically underestimate the real value of the project. The analytical tools required to evaluate options, while more complicated than the usual spreadsheets used for DCF, are becoming more easily available and usable by managers. This paper will discuss the background of options valuation and some of the tools which will make it easier for managers to estimate the value of projects and companies which have significant real option values.ResumeBob McKnight is a graduate of the University of British Columbia in Geological Engineering, supplemented by an MBA from Simon Fraser University. Following several years in the oil patch with Cities Service and Brascan, Bob returned to Vancouver in 1979 to work for Wright Engineers. He subsequently went on to work for Cassiar Mining, Getty Resources and Endeavour Financial before joining Pincock Allen & Holt Ltd. in 1998. His experience ranges from exploration to feasibility studies, financial evaluations of mining and oil & gas projects, due diligence, project finance, valuations and mergers and acquisitions. He has extensive international mining experience pertaining to such countries as Chile, Mexico, Uruguay, Thailand, Indonesia, Angola, Papua New Guinea, Kazakhstan.What are Options?Options have been around for centuries. They were familiar to Roman and Phoenician traders who were shipping cargoes from Mediterranean seaports. In the financial world, options are types of contracts that generally include the right, but not the obligation, to buy or sell a share, currency or commodity. The underlying commodity price or share price changes are assumed to be lognormally distributed. In this context, options are of two general types, ""call"" options and ""put"" options. Call options have the characteristic of having the right to buy a tradable commodity or currency at a predetermined price for a specified period of time. For the owner of call options, they become more valuable as the price of the underlying commodity increases. For the seller of call options, these options become an increasing liability as commodity prices rise, since there is the obligation to sell the commodity at a predetermined (perhaps lower-than-market) price. This characteristic of call options recently became high profile with the sharp rise in gold prices last year. The value of gold call options sold by certain producers increased their associated liabilities to the point where margin calls were made."

Jan 1, 2003

By J. A. Abols, P. M. Grady

Recovery via gravity is one of the oldest mineral processing methods available. Unfortunately, the use of gravity techniques for gold recovery has been in decline for the past century as more effective chemical processes such as flotation and leach/CIP have been developed. Recently, with the push towards more sustainable environmental outcomes, the benefits of gravity separation have become more apparent. While gravity as a unit process is not usually capable of achieving as high a recovery as flotation or whole ore cyanidation, a combination of gravity devices alone or in conjunction with these processes can offer significant advantages to the operator. This paper reviews the range of gravity devices available, their application and the results that can be achieved by maximizing gravity through the use of a combination of gravity recovery devices. Three case studies are provided.

Jan 1, 2005

Since 2008 rapid advances have been made in technologies for the sensing and sorting of ores, particularly copper, and copper-related ores. Advances include significant increases in the sensitivity and throughput, specifically in the area of bulk sorting. Such advances were not possible without contemporaneous advances in the understanding of copper orebodies, in particular the understanding and quantification of the heterogeneity required within an orebody to support an effective sort, regardless of the technology deployed to do this. This paper covers fundamental knowledge in the characterization of orebodies and their ores for sorting; relationships between measures of heterogeneity and sorting response; the design of bulk sorting systems that can exploit this heterogeneity to add value to copper operations; and, a quantification of the value that can be generated from bulk sorting at a case study mine. INTRODUCTION Society currently puts increasing pressure on industries to move towards cleaner and more efficient means of production, and the mining industry is no exception. Mining additionally faces other factors increasing the pressure to be more efficient: high-grade and easily accessible reserves have become largely depleted, therefore the mined grade at operations across most commodities, including and in particular copper, is decreasing. Additionally, the grade of new discoveries in the sector continues to decrease (Schodde, 2011). Factor in the high capital cost of processing facilities and the low levels of efficiency of current grinding circuits, and the situation for such mines becomes dire. Sorting, by maximizing the amount of ore extracted while simultaneously reducing the waste content in ore delivered to downstream processes (whether simply transport and crushing, or more sophisticated circuits such as grinding and flotation or leaching) has long been of interest to mining operations and projects struggling with low margins (Bamber, 2012). However, until recently sorting technologies that are both cost effective and effective at such high throughputs have not been commercially available.

Jan 1, 2019

By A. D. Misener

Introduction Temperature gradients have been determined for numerous locations in the Canadian Shield in connection with mining operations (1, 2, 12, 13, 14, 15). As part of a programme of geophysical studies of this region, some of these gradients were re-determined by the writer at locations where other thermal properties, specific heat, thermal conductivity, radioactivity, etc., were also to be measured. The ultimate object was to determine the heat flow to the surface at these locations. It was felt that the practice of determining heat flow from the temperatures and conductivities obtained in a single vertical bore hole (3, 4, 5, 6, 7, 8, 9) might give results which were appreciably divergent from the average for a considerable area. Particularly, it was thought that temperature gradients, whether obtained in a single vertical hole or from a number of random locations at various depths in a mine, might be subject to local variations and anomalies serious enough to render unsure any discussions based on them. The procedure followed in this investigation was to select a location where mine workings extended to considerable depth over a reasonably wide area. At selected depths below surface, horizontal drill holes extending into regions of undisturbed rock were located and resistance thermometers were inserted into these holes far enough to record the true rock temperature. An attempt was made to obtain a sufficient number of readings at or near any one level to give a representative coverage of the area selected. This ideal could not always be attained, but the large number of readings obtained for each are a does give a reasonably representative picture of the temperature conditions. These readings required much rime and movement of men and equipment underground . They could not have been obtained without the wholehearted co-operation of the management and considerable assistance from the personnel of the mines concerned.

Jan 1, 1949

By R. Amata

"The Gakara Rare Earth deposit in Burundi (East Africa) is unique for its high grade (e.g., 54.3% TREO on average) and low uranium and thorium levels. The majority of the light rare earth (RE) elements in material from Gakara are contained within the familiar RE minerals bastnaesite and monazite. Extensive metallurgical test work was conducted by SGS Minerals Services on mineral samples collected from the Gakara deposit. Various whole ore hydrometallurgical processing routes were examined in a scoping level test program. Preliminary beneficiation testing was also conducted, though it was determined that only marginal upgrading would be achieved with significant RE losses. Thus a hydrometallurgical process on whole ore was developed to minimize the overall process complexity and achieve maximum RE recovery. Results from the test work will be presented, along with the selected base case flowsheet involving agitated atmospheric sulphation of the RE minerals, RE double sulphate precipitation, caustic conversion, redissolution, and carbonate precipitation. Following the base case flowsheet, a purified cerium free mixed RE carbonate with low levels of radioactive elements was produced.INTRODUCTIONRainbow Rare Earths Limited (Rainbow) is a mining company engaged in the exploration and development of the Gakara rare earth deposit in Burundi; Figure 1 shows the project location. The project is located in the Bujumbura Province and 45 km from the Burundi capital of Bujumbura. Notable for its exceedingly high in-situ grade – 54.3% on average total rare earth oxide (TREO), low uranium and thorium levels and familiar rare earth minerals, bastnaesite and monazite – Gakara is the world’s richest rare earth deposit. The project, a previously operating mine from 1948–1978, has a significant mineral inventory base, a long life of mine, well understood mineralogy, and robust economics. Rainbow is focused on bringing Gakara into production in the near term, ramping up to produce 5,000 t/y of a 54%+ TREO concentrate."

Jan 1, 2016