Search Documents

By K. M. Wild, C. D. Martin, F. Amann

"Argillaceous rock formations, in particular clay shales, are notorious for creating challenges in rock engineering. Due to their generally low hydraulic conductivity and their complete saturation in their natural state at depth, the behavior of clay shales is usually characterized by a strong hydro-mechanical coupling.This paper presents typical pore pressure responses monitored in different underground rock laboratories and explores alternative ways for their interpretation. The underpinning processes and their relevance are identified based on analytical and conceptual numerical models. Pore pressure monitoring data from Opalinus clay at the Mont Terri Underground laboratory, the Boom Clay at the Mol facility and the Callovo-Oxfordian clay in the Meuse/Haute–Marne URL show a similar pore-pressure response associated with stress changes accompanying tunnel construction although the tunnels were built in different rock types, at different locations, and under different in-situ conditions.The numerical analyses in this study shows that the pore pressure response around an excavation in low permeable clay shales may have different explanations. Pore pressure drops observed in the tunnel near field can theoretically be explained by both, a pure elastic response in an isotropic or anisotropic rock mass with an anisotropic stress state, or a inelastic response and related dilatancy. However, a comparison between the numerical models and the in-situ measurements revealed that the latter is more likely. This conclusion is justified by the observation that pore pressure drops occur significantly ahead of the tunnel face which is not the case in elastic numerical simulations. Pore pressure measurements in the far field, where failure processes are unlikely to occur, can only partly be explained by a linear poroelastic models. The introduction of an anisotropic material plays a key role in reproducing the responses, conceptually."

Jan 1, 2015

"Virtual reality, a 3D computer-generated environment, has become a recognized delivery system for many forms of education. This paper describes the application of virtual reality to mineral processing education. An interactive mineral processing visualization module developed at the University of New South Wales, Australia, provides users with an overview of a base-metal concentrator and details about how the mined ore progresses through stages in processing. The module also involves developing instructional based plant layouts and flowsheets in the virtual environment. These assist the user in understanding the essential components of the base-metal concentrator.RÉSUMÉ La réalité virtuelle (RV), un environnement en 3D généré par ordinateur, est devenue un système de prestation reconnu pour diverses formes d’éducation. Cet article décrit l’application de la réalité virtuelle à l’éducation dans le domaine de la minéralurgie. Un module interactif de visualisation du traitement des minerais développé par l’université de Nouvelle-Galles du Sud, en Australie, offre aux utilisateurs une vision d’ensemble d’un concentrateur de métaux communs ainsi que des détails concernant la progression du minerai extrait à travers les différentes étapes de traitement. Ce module implique également le développement de schémas de réalisation et de traitement didactiques dans l’environnement virtuel, lesquels schémas aident les utilisateurs à appréhender les composantes essentielles d’un concentrateur de métaux communsINTRODUCTIONVirtual reality (VR) is the creation of an artificial environment that is experienced through sights and sounds provided by a computer (Squelch, 2001). The simulated environment is achieved through technologies such as 3D graphics, audio feedback, and special peripheral devices to produce interactive environments.Virtual reality has been used in diverse fields including medicine (Riener & Harder, 2012), entertainment (Hsu, 2011), military (Manojlovich, Prasithsangaree, Hughes, Chen, & Lewis, 2003), manufacturing (Zimmermann, 2008; Jiang, 2011), and chemical processing (Squires, Andersen, Reklaitis, Jayakumar, & Carmichael, 1992; Schofield, Lester, & Wilson, 2005). Virtual reality is also becoming the recognized delivery system for education in many fields, including engineering (Bell & Fogler, 1996, 1998; Shin, 2002). For example, VR laboratories have been designed and developed to teach users fundamental features of heterogeneous catalytic mechanisms and absorption columns (Bell & Fogler, 1995), the multi-phase and multi-component blast furnace iron-making process (Babich & Senk, 2009), and to guide users to identify various safety measures while working in a real laboratory (Bell & Fogler, 1996)."

Jan 1, 2017

By Juergen Antrekowitsch, Stefan Steinlechner

"Within the last decades, mainly the base metals, like zinc, copper and lead were recycled from different industrial residues without taking into account that accompanied minor side-elements are often also present. A high supply risk for critical raw materials derives mainly due to the high share of the worldwide production in a limited number of countries. Examples include indium and germanium in China, PGM in South Africa and Russia or cobalt and tungsten in the Democratic Republic of Congo. By taking the market of critical metals into account, the recycling of potential residues does not only contribute to an economic treatment but also to the European strategy to decrease the supply risk of certain metals. Depending on the metal discussed, political unrest, decreasing primary resources leading to supply risks in different countries or also simply economic interests moved these mentioned side elements and with this the residues where they are present in, into the focus of the recycling industry.Because of this, the typical routes of lead, zinc and copper production are evaluated concerning generated residues and their typical contents of contained minor elements. Finally, the paper tries to answer the questions how a possible treatment of these wastes could contribute to the overall supply of for example silver but also other minor elements."

Jan 1, 2016

By D. E. Deegan, P. M. Keeley, N. A. Rowson, T. Stachowski

An investigation into the use of Tetronics International’s thermal plasma technology based pyrometallurgical smelting process for the recovery of both platinum and rhenium was conducted. 1000 kg of Pt-Re catalysts containing 0.36 wt% Pt and 0.21 wt% Re was blended with fluxing agents, reducing agents and an iron based collector metal precursor and then fed into a plasma furnace over five individual trials at Tetronics International’s facility in Swindon, UK. Both platinum and rhenium partitioned to an iron rich collector metal phase in the furnace, which formed in-situ and accumulated beneath a less dense slag phase, derived from the inorganic substrate of the catalyst, and was easily separable. The levels of Pt and Re concentration achieved in the iron collector made it suitable for subsequent final refining. Technical recovery efficiencies of =98% for both platinum and rhenium were achieved and the concentrations of the metals in the recovered metal bullion were 2.23 wt% Pt and 1.35 wt% Re.

Jan 1, 2015

By Maurice Lauzon

"Aerial surveys of the open pits have been conducted regularly at Lake Asbestos of Quebec, Ltd. -a subsidiary of American Smelting and Re-fining Company -since 1958. Ground controls are supplied by Lake Asbestos, and a topographic map of the pits at a scale of 1 in. to 50 ft., with 2-foot contour intervals, is obtained by aerial photography. The information from the topographic map is then transferred by the Lake Asbestos engineering staff to sections from which the volumes removed are calculated. Considering the size and complexity of the operation, this system has proved to be the cheapest, fastest and most accurate way of determining the quantities of rock and overburden removed. More than 11,000,000 tons of ore and waste are mined each year in three different pits. Further-more, the nature, shape and extent of the orebodies make it necessary to mine on many (up to eight) benches of a pit during a single year. In addition, there are sections of the pits where it is impossible or un-safe to survey the crest of some benches by standard ground methods. For these reasons, the tonnages obtained by truck count are checked and adjusted by aerial survey. These surveys are now taking place every six months. With this system, it is possible for a two-man surveying crew to look after all field work in the mine area."

Jan 1, 1967

By G. P. Contractor

Medium and low carbon steels, modified with uranium, were studied in order to evaluate the influence of uranium on forge ability, mechanical 11roperties, response to heat treatment and microstructure. Uranium contents ranged up to 0.70 per cent. The medium carbon steels are hot short if the uranium content exceeds about 0.35 per cent. More uranium can be tolerated in low carbon steels. The hot shortness is caused by the formation of intergranular phase UFe2. Critical transformation temperatures, Jominy hardenability, and resistance to tempering are not significantly affected by the 11resence of uranium. Similarly, uranium has little or no effect on the tensile properties of carbon steels. The addition of uranium has a favourable effect 11n the stress-rupture characteristics and some beneficial effect on fatigue properties. However, more results are required for verification. In the steels investigated, it seems that most of the uranium carbide combines to form complex inclusions of U (0, C, N) or (C, N), rich in oxygen or nitrogen or both.

Jan 1, 1963

Reaction between xanthate ions in solution and oxidized compounds present on the surface of galena to form lead xanthate is considered to be a side reaction not contributing to flotation, although accounting for some consumption of reagent. The direct reaction of lead sulphide with xanthate and oxygen to form lead xanthate is the most significant to flotation. Coadsorntion of dixanthogen is also involved. Previous work has shown lead recovery in lead rougher flotation to be a function of m [H+] where: m = concentration of xanthate in solution rHl = hydrogen ion concentration. A plausible explanation for this relationship is suggest-ed. Likewise, the experimental findings that the amount of xanthate adsorbed under certain conditions is a function of m'[H+] are explained in terms of reaction between xanthate ions and soluble basic lead salts such as PbO.PbS04? It is also shown that m[H+] should have a constant value in lead cleaners operating at a higher pH than the roughers. This conclusion is confirmed by plant data, and the value of the constant agrees well with the calculated value. The finding is useful in mill control.

Jan 1, 1965

By R. E. Whitehead, G. J. Prior

"Abstract -Biotite from aplite that appears to have crystallized simultaneously with disseminated Cu-Mo mineralization at MacLeod Lake in northern Quebec yields K-Ar dates in the range 2032 ± 44 Ma to '2f1:)1 ± 47 Ma. The mean value, 2065 Ma, is some 400 Ma younger than the 2485 ± 64 Ma date obtained from a hornblende concentrate separated from a granodiorite sill that is spatially, but apparently not genetically, associated with the disseminated Cu-Mo deposit. The mean biotite date of 2065 Ma at MacLeod Lake, a K-Ar date of 2055 Ma reported from an area 50 km east of MacLeod Lake and published dates of about 2000 Ma for galenas from the Chibougamau Cu-Au ores, suggest a widespread thermal and mineralization event, in that part of the Superior Province east of James Bay, that differs from the common late Archean mineralization that is related to volcanism and metamorphic-intrusive activity.Sommaire - Les datations au K-Ar sur des biotites qui auraient cristallisé en même temps que la minéralisation disséminée en Cu et Mo dans une aplite mise en place au Lac MacLeod, au nord du Québec, s'échalonnent entre 2032 ± 44 Ma et '2f1:)1 ± 47 Ma. La datation moyenne, soit 2065 Ma, est d'environ 400 Ma plus récente que la datation obtenue pour un concentré de hornblende extrait d'un fùon-couche de granodiorite qui est spatialement mais ne serait pas génétiquement as­ sociée à la minéralisation disséminée en Cu et Mo. La datation moyenne de la minéralisation au Lac MacLeod, soit 2065 Ma, la dataion au K-Ar à 2055 Ma citée pour une région à 50 km à l'est du Lac MacLeod, de même que les datations d'environ 2000 Ma établies pour des galènes qui se trouvent dans le minerai aurifère et cuprifère à Chibougamau, suggèrent un phénomène thermique répandu qui aurait produit la minéralisation dans cette région à l'est de la Baie James, dans la province du lac Supérieur. Ce phénomene serait différent de celui qui aurait produit la minéralisation répan­ due d'âge archéen tardif qui elle serait associée à l'activité volcanique et à l'activité intrusive accompagnée de métamorphisme."

Jan 1, 1992

By Pingyang Zhang, Caichu Xia, Shuwei Zhou, Yu Zhou, Yongsheng Hu

A lined rock cavern (LRC) is an alternative container for compressed air energy storage (CAES) to store high-pressure air that is later used to produce electricity. A critical requirement of CAES in LRCs is that the inner seal should provide adequate sealing capacity to prevent air leakage from LRCs. In many studies, rubber sheets are applied to build the inner seal. However, air leakage through rubber seals has not been given much attention and rubber seals are usually assumed to be absolutely airtight. Given that rubber is permeable especially under high air pressure, such as in CAES, air therefore leaks through rubber seals during CAES operations. In this study, a numerical analysis was conducted based on the permeation equation of polymers and the governing equations of thermodynamics of CAES caverns to analyze the characteristics of air leakage from CAES caverns through rubber seals. A planned CAES plant in China was considered as a case study. Results show that air leakage rate increases with increasing cavern temperature and pressure during air injection and decreases as cavern temperature and pressure decline during air withdrawal. However, in total, the daily air leakage percentage is in the order of magnitude of 10-3% in a typical operation cycle, which is much smaller than the critical value of 1%. Under a common range of realistic operations conditions, the daily air leakage percentage is still of the order of 10-3%. Therefore, rubber seals can be used to prevent air leakage in LRCs for CAES. However, the experience of Japanese pilot cavern indicates that the specifications for the on-site vulcanization jointing and installation methods of rubber seals still need improvement.

Jan 1, 2015

By Andrew Bamber

The mining and beneficiation of minerals is the second largest end-use of electrical power on the planet, and comminution is by far the largest single contributor to this. Several jurisdictions, including British Columbia, have, in response to concerns about greenhouse gas emissions and climate change, adopted energy conservation legislation, including carbon taxes, carbon trading and conservation incentive schemes. Key to achieving conservation objectives is firstly an understanding of usage metrics across the various unit operations in the sector, and secondly an understanding of the conservation potential represented by available technologies and approaches in reducing end-use. This paper presents the results of a recent utility-funded study on energy use metrics and conservation potential at large open pit mines which are typical of the sector in BC.

Aug 1, 2013

By Kenneth G. Thomas

Since approximately 2003 we have witnessed the unprecedented escalation in commodity prices. Coupled with economic chaos following the 2008 economic downturn this has caused difficulties in controlling schedule, capital costs and operating costs for mining projects. Once again escalation has returned to commodity prices fuelled by growth in the BRIC countries especially China and Brazil. This is further exasperated by the missing generation of skilled technical personnel not graduating from universities in the 1980s and 1990s owing to depressed commodity prices. This paper examines the six tenets for successful project implementation.

Jan 1, 2011

By C. Mills, A. O. Burt

"The paper examines the role of gravity concentration in both an historical context and within the modern mineral processing industry. It discusses the principles of the process on both a theoretical and practical level. The importance of more mineralogy and its effect on the choice of the wide range of equipment available is discussed. The paper concludes with a discussion on the relative merits of gravity concentration with other forms of processing.IntroductionIt is an unfortunate, albeit popular, misconception among otherwise enlightened engineers in the mineral processing industry that gravity concentration was a process developed in the dark ages, perfected in the middle ages, and abandoned in the modern ages.Gravity concentration was developed in the dark ages - long indeed before that. Agricolau: cited examples of gravity concentration, crude examples admittedly, being practiced over 3000 years ago. However, gravity concentration is not dead. Far from it. As recently as 1978 it was reported that the total mineral tonnage treated by this process in the United States was greater than that processed by flotation. Coal represents the bulk of the or e treated by gravity separation in the U.S.A., with iron ore representing a major portion of the balance."

Jan 1, 1985

By C. E. Ells

Current knowledge of the behaviour of inert gases in metals is reviewed, with particular emphasis given to the phenomenon of the growth of gas-filled bubbles.

Jan 1, 1960

By K. E. Prince, S. Burling, R. J. Ring, M. K. Maley, W. R. Taylor

Vanadium occurs as a component of carnotite, which commonly occurs in calcrete type ores, and in association with uranium in some sandstone-hosted deposits. Increasing demand for vanadium, which is used in high-strength steel and Vanadium Redox Flow Batteries (VRFBs), is offering some uranium producers a potential option for by-product vanadium recovery to improve project economics at a time when uranium prices are low. This paper presents the results of recent optimisation studies on the Bigrlyi deposit for the recovery of both uranium and vanadium. The impact of carbonate leaching conditions on uranium and vanadium extraction from a range of carnotite-in-calcrete ores is also examined, with vanadium extraction limited by the proportion of non-carnotite vanadium present in the ores. The findings are particularly relevant to developing projects as results show that elevated vanadium content in ore does not necessarily equate to a high vanadium extraction in leach.

Jan 1, 2020

By Yvon T. Maurice

Under the auspices of the Federal-Provincial Uranium Reconnaissance Program, a geochemical orientation survey was undertaken in an area of uraniferous Lower Proterozoic (Aphebian) rocks near Cape Dorset in southwest Baffin Island. The main objective of this study was to establish a methodology for a future reconnaissance geochemical program using lake samples over a 300-mile Lower Proterozoic rock belt that occurs along the southern coast of Baffin Island. Mineralogical and chemical studies of known radioactive occurrences, combined with detailed sampling of secondary environment media in the vicinity of the showings. indicate that uranium is the most significant pathfinder, despite considerable enrichment of other metals in the uraniferous rocks, Significant geochemical patterns produced by uranium in lake waters and uranium in lake sediments have been obtained, but their relative usefulness depends on the distribution of carbonate bedrock, which in turn affect the bicarbonate content of lake waters. In southern Baffin Island, because of erratic variation in lake-water alkalinity, it is recommended that both water s and sediments be sampled on a routine basis. The need for lake-water acidification to prevent depletion of soluble metal ions in samples resulting from adsorption on the walls of the containers and/or suspended solid matter is discussed briefly. The base metal potential of the area was examined in some detail and found to be significant, particularly for a Lower Proterozoic gossanous formation that occurs throughout southern Baffin Island.

Jan 1, 1977

By Sunil S. Gandhi

Magmatic-hydrothermal deposits rich in magnetite and/or hematite form a broad group that includes monometallic Fe deposits and polymetallic (mainly Cu and Au) deposits. They show a considerable variation in deposit characteristics, but share the genetic processes of magmatic differentiation and related hydrothermal activity in intermediate to felsic melts, and in some cases involve brines and/or meteoric waters during mineralization. They include several world-class deposits. They range in age from Proterozoic to Recent, and form important metallogenic districts in Scandinavian, Canadian, Brazilian and Australian Shields, Circum-Pacific regions, and in China, Iran and Turkey. Monometallic deposits have been important sources of iron in the past and still contain significant resources of the metal, e.g., the Kiirunavaara deposit in Sweden. The giant Olympic Dam Cu-Au-Ag-U-REE deposit was discovered in 1975, and since then explorationists have focussed on search for analogues worldwide. This has brought to light a number of economically important new deposits and prospects, including examples in Canada. The discoveries have in turn prompted considerable research on individual deposits and the group as a whole. This short paper is an attempt to summarize the main aspects of the group from the literature cited in Gandhi and Bell (1996), and from the papers published recently in two milestone volumes on these deposits, edited by Porter (2000 and 2002).

May 1, 2003

By Robert D. McKellar, Luke Frawley, Richard Okrasa

"The resource industries in Canada are facing increasing global competition and stringent environmental regulations. This has made it essential for companies to lower operating costs wherever possible. Electrical energy rep-resents one variable cost that may be better managed and utilized, providing the user with lower operating costs, improved productivity and better yields.The utility industry is also facing changes in the way it must do business. Utilities in North America are facing the prospect of deregulation that will eliminate the monopoly they have traditionally held. This will force them to strive for lower operating costs, to maintain a competitive position and to improve customer ser-vice so as to maintain their customer base.Ontario Hydro has been working with industry for several years. Many opportunities for cost savings have been identified involving energy efficiency, process improvements and the use of new electro technologies. One useful service that the utility can offer industry is to increase the awareness of potential opportunities suited to their operations. This paper will provide an overview of some of the projects that have been implemented and those that are presently being evaluated. An electronic data-base of electro technology applications that is under development will also be described."

Jan 1, 1996

By T. E. W. Nind

"A short description of the chamber lift method for producing oil wells is followed by some comments on compressor requirements and gas utilization. A quantitative analysis of the process is presented and, based on this analysis, criteria are suggested for selecting wells for which this type of lift might be suitable. The analysis leads to the conclusions that chamber lift is an efficient producing mechanism for wells having very low productivity indices (say about 0.05 bbl/d/ p.s.i. or less), but that for such wells optimum utilization of injection gas cannot be attained. It is suggested that the gas injection time per cycle should be kept as low as possible, compatible with a small oil fallback volume, and that the cycle frequency should be in the range of 20-40 cycles/ day. For wells with productivity indices of 0.2 bbl/d/p.s.i. or higher, chamber lift is relatively inefficient; how-ever, if well allowables are low it may offer an attractive, low cost, alternative to gas lift or pumping."

Jan 1, 1960

By DONALD E. BARNETT

Since the days of early settlement ew Brunswick has produced a variety of industrial minerals but it is perhaps only the recent discoveries of significant reserves of potash that have elevated the meaning of industrial minerals in their contribution to the provincial economy. With potash production commencing in July 1983, the role of industrial minerals will increase significantly to the value of mineral production in the province.

Jan 1, 1984

By S. K. Dimitrov

?Ellatzite Med? is one of the biggest mining companies in Bulgaria, processing about 12,000,000 t of ore per year. Waste materials left after extraction of copper concentrate are deposited in tailings dam ?Benkovski 2?. The hydraulic structure is built according to the downstream method, through hydrocyclonization where the downstream batter and the body of the wall are formed by the separated coarse sand particles of the separated tailings. In connection with the prolonged concession of Ellatzite Med and the enlarged capacity of Benkovski 2, the tailings dam has expanded on to the surrounding terrain. To guarantee a normal hydrocyclonization and build up of a tailings wall during waste deposition from the ore mill, the technological scheme of the hydraulic transport system of Benkovski 2 has been changed.

Aug 1, 2013