Search Documents

By W. G. Campbell

"The region discussed comprises approximately eight million acres spreading across the Arctic Circle in Yukon and North West Territories.Encouraged by four years of surface geological and geophysical work, which strongly suggested that suit-able conditions existed for the entrapment of oil and gas, a decision was reached to drill. In due course two holes were drilled; Eagle Plains No. 1 drilled to 9589 in 1957-8 and Western Minerals Chance No. 1 spudded in 1959 is being deepened this year.Thick sections of sedimentary rocks occur on both sides of the Richardson Mountains, however, most of our activities have been concentrated to date on the west side in the Eagle Plains basin. Here are found stratigraphic units ranging from Precambrian to Tertiary age. The drilling of the two exploratory wells proved the presence of these strata at depth and have confirmed the presence of promising structures. A geological cross-section across Eagle Plains presents an interpretation of these conditions.Physical and engineering aspects of exploration in the northern Yukon and North West Territories are de-pendent largely upon seasons and transportation. Reconnaissance gravity and surface geologic mapping by air presents no serious problems. However, seismic operations on the ground are greatly affected by the season, presence of permafrost and mobility of equipment.The actual drilling of the hole may well be the simple part of a wildcat undertaking once equipment and supplies are on location. Over-all planning, assembling supplies, transporting equipment and personnel seems to be the real job. Serious consideration must be given to per-ma-frost effect in the drilling pro-gram and on surface installations as well.Programming for -the various exploration activities should be under-taken well in advance of the actual doing. Considerable extra costs may be the results of crash programs. Costs are high, and the rewards uncertain. Economic evaluation is based •on the long term outlook."

Jan 1, 1960

By W. R. A. Graeser

"The Nordenham finishing mill is situated in the town of Nordenham, Fede1•al Republic of Germany, on the banks of the Weser River opposite the town of Bremerhaven, with access by water to the North Sea.The unfinished fibre, shipped j?•om Deception Bay during the sub-Arctic summer shipping season, is unloaded from bulk ocean carriers, stored and then processed throughout the year until the following shipping season. This paper describes the unloading and storage facilities,the finishing mill and the finished-fibre storage arrangement. Details of environmental and dust control practices and West German environmental standards are discussed. A resumé of fibre markets is included."

Jan 1, 1976

By R. Butar-Butar, J. Mosher, G. Banini, J. Hollow, A. Villanueva

The effect of High Pressure Grinding Rolls (HPGR), as a preceding stage to a conventional ball mill circuit at PT Freeport Indonesia’s C1/C2 concentrators, has been studied in terms of downstream grinding efficiency and circuit performance. When milling the product from the HPGR, mill capacity increased by 21% for the same product grind size, when compared to processing similar ore from a conventional crushing circuit. This achievement is a result of several reasons, among them: reduction in feed size (F80), fines generation beyond the proportional reduction in F80, reduction in ore hardness induced by HPGR comminution mechanism, optimization of the recycle system of the HPGR and ball string optimization in the ball mill circuit given the new feed to the mill.

Jan 1, 2012

By K. J. Heale, G. G. Richards, D. J. Rioux, R. L. Stephens

Slag fuming has remained a key process for the recovery of Zn, Pb, and minor elements in the integrated flow sheet at Teck Cominco's Trail Operations for more than 75 years. Since the start-up of the KIVCETTM process and the #3 slag fuming furnace in 1997, a range of process intensification projects have been completed to improve metals recoveries and throughput based on improved process control, mechanical modifications, and, most recently, the implementation of oxygen enrichment of the blast air. This latter project, initially named 'nitrogen depletion' and now 'nitrogen oxygen performance enhancement' (NOPE), is the primary focus of this paper. NOPE reduces the amount of heat required to heat the inert nitrogen gas, and therefore more of the energy input can be used for reduction. It also frees up boiler capacity because the inert nitrogen gas does not then have to be cooled down. A dynamic METSIMTM model was developed to determine the opportunities to improve the process capacity and heat balance to both assist with justifying the project and to verify the observed furnace behaviour. Several process safety management issues were also addressed and a few key minor mechanical modifications were made to allow the project to proceed to commercial implementation at 25% blast air oxygen enrichment. Short term plant trials have confirmed the model predictions. The first three months of a long term, continuous trial showed a 6% increase in zinc fuming rate from average furnace performance despite the implementation of a KIVCETTM fluxing change to assist with minor element recovery that was expected to negatively impact the zinc fuming rate by 3 to 5%. This encouraging result is also in line with the model predictions.

Jan 1, 2008

By J. U. MacEwan

THE basis on which the modern metallurgical industry is operated is the endeavour to attain maximum return in purchasing power for the least expenditure of energy. This has always been the general objective of the industry, as of all industries. In recent years, however, it has received a new emphasis. Today, as never before, increased attention is being directed to the detailed study of plant operations and the application of scientific knowledge and of business principles in order to achieve the maximum efficiency. This new emphasis is the result in large part of the new problems and conditions with which the industry has been confronted, chief among which are the following: (l) Development of new ore-bodies and the treatment of complex ores. (2) Necessity of achieving a greater degree of purity in some of the metals in order to meet the newly discovered demands for some of the industrial metals. (3) Discovery of new markets for many of the metals, either in pure form or in the form of alloys. ( 4) Change in values, absolute or relative, of some of the important metals. (5) Increasing scale of investment in expensive plant and equipment, which makes imperative most efficient utilization if total unit costs are to be kept to a minimum. (6) Increasing scale of operations in some important branches of the industry, which also makes essential maximum efficiency in organization, administration, and operation. The success with which the metallurgical industry has met the problems created by these changing conditions has been due primarily to the following factors: (1) Results of research and experimental work carried on by universities, government laboratories, and many private corporations in the industry itself. (2) Closet study of every detail of plant operation, both from the technological and from the economic point of view, with the object of increasing plant efficiency. (3) Interchange of information and experience amongst the operating companies. It is only by the concerted efforts of numerous investigators and experimenters that the underlying fundamentals of plant operations can be learned. The exchange of results permits their easy assembly and correlation with maximum benefit to the whole industry. Unnecessary duplication of research and experimental work is avoided and the industry as a whole is able to reap the fruits of this work with the maximum of-speed and efficiency. (4) Advances made in recent years in so-called 'scientific management' in industry as a whole and the application of the principles learned to the metallurgical industry. A review of the modern trends in extractive non-ferrous metallurgical processes illustrates the afore-mentioned new conditions and problems, and gives some idea of the methods by which they have been and are being surmounted.

Jan 1, 1937

By E. Nolasco, J. Ouellet, T. Tikka

"Shaft bottom structural systems are used in underground mining to support transfer of personnel, equipment and ore to and from underground to the surface. This paper first summarizes the evolution of design philosophy from a concrete tower supported on a concrete plug to the current structural steel design arrangement with unlined shaft walls, clear shaft bottom area with only a concrete housekeeping pad. Then the paper reviews the design parameters, analysis and design, and construction methodology for this rather unique shaft bottom structural system consisting of three sets of hitch beams, with each having specific functional requirements. INTRODUCTION Shaft bottom structural systems are used throughout the world in underground mining operations to provide a means to support the transfer of personnel, equipment, materials, ore and waste entering and exiting a vertical shaft ready for transport to and from the surface via the hoisting system. The shaft bottom structural system, for the Service Shaft (SS) at the Jansen Mine, is designed to accommodate two skips, a personnel/equipment cage, counterweight, services, loading pocket, rope changing, arrestor system, crash (or catch) beams, access platforms, stairs and rope divider system. Stantec and BHP have engineered a unique structural steel shaft bottom system for hoisting system at a Potash Mine. The shaft bottom structural system connects to a fixed guide and cantilever bunton system, used in the vertical shaft (shaft barrel), above the shaft bottom. The geometry for the shaft bottom structural system, shown in Figure 1 a), features three sets of hitch beams, beams which span across the shaft excavation or barrel. At the top of the structural system are two upper hitch beams. These hitch beams support a 64 metre suspended rectangular braced tower (upper tower), complete with steel guides for the conveyances. The upper tower passes through the main station (potash or mining) level and then connects to the top of the arrestor (lower) tower structure via a sliding vertical connection. The potash level is supported by two hitch beams spanning the shaft and loading pocket excavations. The arrestor tower, a braced compression tower structure, is carried by a third set of hitch beams. Below the third set of hitch beams is a short suspended tower complete with access platforms, stairs and the rope divider system."

Jan 1, 2019

By C. Lambert

It has been shown that contacts between host rock and engineered barriers may be critical in the design of deep radioactive waste repositories. Water is expected to reach the interface zone after the re-saturation of the geological massive and its presence may lead to concrete leaching. Such a phenomenon could increase the interface transmissivity and compromise the confinement of radioactive waste. Recent experimental results from Buzzi et al. (2008) have enhanced how concrete leaching can drastically change the mechanical behaviour of such interfaces. Because of the local loss of strength resulting from leaching, shearing resulted in a degradation of the interface asperities. Similarly to rock joints, intact interfaces exhibit a usual contracting-dilating behaviour. On the contrary, depending on the extent of leaching, the degraded interface can display a fully contracting. This paper intends to investigate the influence of concrete leaching on the mechanical behaviour of host rock-concrete interfaces. The leaching process consists in the dissolution of some of the hydrates of the cement paste, leading to a reduction of the strength and Young's modulus. A discrete model has been developed with PFC3D where a simplified interface morphology has been introduced using a saw-tooth description of the asperities.

May 1, 2009

By G. A. Brown

"Mining executives are becoming increasingly involved with decisions of the ""What would happen if ... "" variety. Potential changes in government policy, such as tax incentives, E.G.M.A. allowances, etc. affect the economic future of present and proposed mining ventures.This paper will discuss various measures of effectiveness normally used in assessing this future, such as discounted cash flow, etc., and will describe means of introducing uncertainty into the computations. As the recognition of risk and attitudes toward accepting it are very important in the life of a mine executive, there will be a brief discussion of utility theory and its application to risk analysis.Risk models are usually of a size to warrant the use of an electronic computer. Therefore, to demonstrate the simple interaction necessary between a financial analyst and such a model, data will be read into a remote computer from a time-sharing terminal in the meeting room. It will be shown that changes may be rapidly made and alternative policies investigated ""on line"" to a computer."

Jan 1, 1970

By J. G. Cullain

Inco Limited is an integrated mining, smelting, refining and manufacturing company with operations located worldwide. The Ontario Division operations consist of 13 mines and 10 processing facilities located in Sudbury, Port Colborne and Shebandowan. The scope of our utilization of energy in the Ontario Division in 1976 included in excess of 2.2 billion kilowatt hours of electric power, 12 billion cubic feet of natural gas, 60 million Imperial gallons of residual oil and smaller quantities of other fuels. In addition to the primary energy consumption, waste-heat energy is recovered in various operations throughout the Division, thereby reducing our primary energy requirements. Total expenditures for primary energy alone in 1976 exceeded 60 million dollars. Energy management studies were initiated by Inco's Utilities Department in late 1972, and resulted initially in a program of electric power cost reduction. This program produced significant results by improving the use of the water available for our hydraulic generation facilities and by a comprehensive peak reduction program. Our experience showed that a program of peak power control creates an awareness of both peak and energy costs, and thereby encourages a general reduction in the electric energy consumption as well as lowering the peak demand. Energy management is a continuing program at Inco and, recently, a formal energy management policy and program was instituted. Energy management committees were formed in each plant or mine area to identify the major areas for energy; consumption, thereby isolating areas with large potential energy losses, and determining immediate action which will improve the energy efficiency or reduce the energy waste within their respective areas. A decentralized program with good cross-communication between all committees was felt to be the best method of providing an on-going effective energy management program. In the future, the projections of dwindling fossil-fuel supplies in Canada and the resultant spiralling energy costs will further emphasize the need of sound energy management practices for all Canadian industry.

Jan 1, 1977

Of the twelve known ore zones on the Sunro property, acquired by Cowichan Copper Co., only the "B" and "C" orebodies of the "River Zone" had been explored sufficiently to indicate the grade and tonnage. The "B" zone was selected for initial production. The portion of this orebody above the main adit level was developed for horizontal-ring, longhole mining. Ore from the stope would be scraped directly to the coarse ore bin. The lack of a suitable mill site on surface, as well as the 8,000-ft. tramming distance, led naturally to the installation ground. I N November, 1960, a lease was obtained by Co-wichan Copper Co. Ltd. (N.P.L.) from Sunro Mines Ltd., covering the main ore (River) zone of the Sunro property. A total of twelve zones had been located on the property. Nine of these lay within the leased area. With the exception of the "B" and "C" orebodies of the River Zone, there had been insufficient exploration for tonnage and grade calculations. Exploration by previous companies had

Jan 1, 1965

The negative effects of pyrite and pyrrhotite on thiosulfate gold leaching have been investigated. Possible remedies to reduce some problems are discussed. In a gold bearing pure silicate ore, 92% of gold could be extracted within 3 hours using a solution containing 0.2 mol/L ammonium thiosulfate, 0.9 mol/L ammonia, 30 - 300 ppm copper sulfate and 8.6 ppm dissolved oxygen at pH 10.26. The thiosulfate consumption was 7.1 kg/t under these conditions and could be further reduced to 3.5 kg/t by decreasing the dissolved oxygen to 0.3 ppm. Addition of 16% pyrrhotite or pyrite into the silicate slurry led to a decrease in gold extraction by 2% or 9% respectively and an increase of thiosulfate consumption by 11 kg/t or12.8 kg/t respectively in three hours. Several adjustments, such as increasing copper ion and ammonia concentration and reducing the dissolved oxygen level to 0.3 ppm resulted in increased gold extraction and lower thiosulfate consumption despite the presence of these sulfides.

Jan 1, 2005

By M. Tadayonsaidi

The effect of alloying elements on the mechanical properties and thermal expansion of 336 casting alloy usually used as piston alloy which has low thermal expansion and very good high-temperature mechanical properties and good wear resistance was investigated. The mechanical properties and thermal expansion characteristic of samples with different combination of alloying elements, which enhance to reduce the cost of products, have been studies, The results show remarkable increase in the mechanical properties with increasing the amount of Cu and Mg, while are reduced with increasing amount of Ni, On the other hand, the use of eutectic aluminum alloy as 336 alloy with higher percent of Cu and Mg and lower percent of Ni are recommended for industry, due to economical viewpoint and satisfactory properties.

Jan 1, 2005

By S. R. Steinacker, H. Schnideritsch, J. Antrekowitsch

Primary copper industry flue dust plays an increasingly important role in the creation of matte and slag. From a thermodynamic point of view, the chemically formed section of fine particles play a techno-logically interesting role in comparison to the mechanical carry-over. Here, the volatilization and the sub-sequent condensation in the off gas system lead to a characteristic distribution of the contained elements which are represented by various compounds of desired metals like zinc and lead. On the contrary, certain undesired components such as arsenic, bismuth and cadmium accumulate within the product as well. This paper describes existing models and theories concerning the formation of flue dust in the copper smelting process and presents a thorough investigation of the physico-chemical fundamentals by verifying assump-tions with thermodynamic calculations. By fully understanding the formation patterns at different stages and temperatures within the process, better knowledge for flue dust in the first step of the pyrometallurgi-cal copper smelting can be obtained - hence leading to new ideas and incentives for the following stages in the copper production cycle.

Jan 1, 2015

By D. Milne, G. Snell

"A new method to predict stope hangingwall failure in underground excavations is proposed. This method compares movement rate for stope hangingwalls, determined from changes in strain or deformation, with changing opening geometry. This geometry is represented by the effective radius factor (ERF), a measure of relative distance to supporting abutments from an opening surface point. This strain-ERF (SERF) approach is applied to an instrumentation program for Brunswick mine near Bathurst, New Brunswick. The SERF method for this case study predicted failure at an ERF of 13.9 m and hangingwall failure actually occurred at an approximate ERF of 12.4 m.RÉSUMÉ Cet article propose une nouvelle méthode permettant de prévoir la rupture de l’éponte supérieure des chambres d’abattage dans les excavations souterraines. Cette méthode compare la vitesse de mouvement des épontes supérieures des chambres d’abattage, déterminée à partir des changements aux niveaux des contraintes ou de la déformation, à la géométrie variable de l’ouverture au jour. Cette géométrie est représentée par le facteur du rayon effectif (ERF, de l’anglais Effective Radius Factor), une mesure de la distance relative jusqu’aux appuis latéraux de soutènement à partir d’un point de la surface d’ouverture au jour. Cette approche contraintes-ERF (SERF, de l’anglais strain-ERF) est appliquée à un programme d’instrumentation pour la mine Brunswick située près de Bathurst, dans le Nouveau-Brunswick. Pour cette étude de cas, la méthode SERF prévoyait une rupture à un ERF de 13,9 mètres (m); la rupture de l’éponte supérieure s’est effectivement produite à un ERF d’environ 12,4 m.INTRODUCTIONUnderground stope design can be improved with the installation of field instrumentation. The most commonly used instrumentation for monitoring rock mass behaviour around open stopes is extensometers. The y-axis of Figure 1 represents how the changing rate of movement, measured using either displacement- or stress-type instruments, can be observed over time. The magnitude of movement measured by extensometers can give an approximation of the load on installed support (Milne, Pakalnis, & Lunder, 1996) and a changing rate of movement can indicate approaching instability."

Jan 1, 2018

By N. Parnian

"Carryover of caustic soda (NaOH) in the steam path caused catastrophic failure of superheater 304H stainless steel tubes in a steam generator and led to an unexpected shutdown after just five months of continuous service of petrochemical following the start of production. The cause of the failure was studied, with a focus on the formation of sigma phase in the weld joint and effect of caustic embrittlement on stress corrosion cracking (SCC). The cracks were examined at the seam weld, heat affected zone (HAZ), and Ubend areas. Hardness was measured for the base metal, HAZ, and weld metal, and microstructures were examined using optical microscopy and scanning electron microscopy (SEM). Crack initiation is attributed to gouging on the precipitated carbide at the HAZ and also the formation of sigma phase in the weld metal, as shown by energy dispersive X-ray (EDX) analysis. In addition, cracking was propagated by caustic embrittlement because of residual stresses and hammering. Finally, the characteristic feature of fracture was illustrated by SEM fractography, and consists mostly of intergranular SCC and some quasicleavage transgranular. INTRODUCTIONThree key factors are needed for the initiation and propagation of intergranular stress corrosion cracking (IGSCC): a susceptible material, a corrosive environment, and sufficient stress. Although austenitic stainless steels are susceptible to sensitization and IGSCC, they are widely used in boiler and superheater tubes because of their high corrosion resistance, high oxidation resistance, acceptable mechanical characteristics at elevated temperatures, and low cost.Sodium hydroxide is injected to neutralize acidic constituents in the steam path, but caustic can concentrate in boiler tubes and attack the surface metal (known as gouging) even traces of caustic in the steam can deposit on surfaces and cause local concentrations of several percent (ASM handbook, 1992). Not only sensitized grains but also sigma phase formed in the weld metal can initiate caustic cracking. In this research, the cause of the failure of 304H stainless steel superheater tubes in a methanol petrochemical plant in Iran was studied with a focus on the effects of caustic embrittlement on IGSCC."

Jan 1, 2012

By K. Izumi

Ultra-grain refinement and high strengthening of metals by accumulative roll bonding (ARB) was widely reported. However, applications of ARB to magnesium alloys were rather limited. In this study, Mg-9%Li-1%Y sheets were applied to ARB at room temperature. Six 0.5 mm thick sheets were stacked and reduced into 0.5 mm thick by four passes. The procedure was repeated up to three cycles, so that the equivalent strain of 6.2 was applied. The sheets show dual phase structure with a (hcp) and ß (bcc). Grains elongates to the rolling direction with increasing number of ARB cycles. After three cycles, fragmented a grains with average size of about 300 nm are uniformly distributed. After the first cycle, the ultimate tensile strength increases to 180 MPa from 133 MPa, while the elongation decreases, however, still high (26%). The tensile strength slightly decreases by the second cycle and does not change at the third cycle. Meanwhile the elongation increases by the second cycle and the sheets show 41% of the elongation after the third cycle.

Jan 1, 2006

By M. Epiney, A. Ghahreman, R. Kim1and

"Pre-oxidation and cyanide leaching behavior of gold in the presence of sulfide minerals were reviewed, focused on the effects of oxygen injection in the gold leaching process. Generally, pre-oxidation and gold leaching kinetics from iron sulfide refractory minerals, such as pyrite, pyrrhotite, marcasite, pentlandite and arsenopyrite, can be enhanced with higher dissolved oxygen (DO) concentration. However, most of copper sulfide minerals dissolved well both in water and cyanide solutions, and copper from the minerals consumed DO and cyanide to oxidize and leach. Only in the presence of chalcopyrite, gold leaching was effectively occurred with increasing DO. However, chalcocite and covellite severely retarded gold leaching. Stibnite, an antimony mineral, formed a passive film on the gold surface under any DO conditions, and it slowed gold leaching. This impeding effect can be alleviated by leaching at low pH or adding lead salt. Using oxygen and lead together can make synergistic effect in oxidation of sulfide minerals and can enhance gold extraction. Depending on the mineralogical characteristics of the ore, the optimum DO and lead concentrations can be optimized. However, lead can cause environmental problems, and so its dosage should be minimized or eliminated by substituting it with oxygen injection.INTRODUCTIONGold ores containing sulfide minerals are becoming more significant as high grade gold oxide deposits are continuously becoming difficult to find. In light of this situation, to produce more gold, recovery methods from refractory gold ore containing various sulfide minerals should be investigated. Generally, sulfide minerals have impeding effects on gold leaching: formation of a passive film on the gold surface, high consumption of chemicalssuch as cyanide and oxygenduring leaching, reduction of gold cyanide by sulfide ions, etc. (Senanayake, 2008). Therefore, sulfides must be properly treated for better gold recovery. Pre-oxidation of sulfide minerals by injecting pure oxygen can decrease the impeding effects in gold leaching. Prior to cyanidation, sulfide minerals can be oxidized to metal hydroxide and sulfate form, which consume negligible cyanide in the following cyanidation circuit (Bodnaras et al., 1993). Moreover, gold cyanidation can be enhanced by increasing concentration of the dissolved oxygen (DO). In general, the optimum concentration ratio of [CN-]/[O2] is calculated as 6, but it goes higher in the real system (Marsden &House, 2006), which means that the reaction is typically controlled by DO concentration."

Jan 1, 2017

By Mary A. Wells, Amir Hadadzadeh, Mark A. Whitney, Stephen F. Corbin

In an effort to produce less expensive titanium sheet via roll compaction, the room temperature compaction behavior of titanium sponge granules (99.9% pure, Alfa Aesar) was studied under uniaxial die compaction. The titanium sponge granules were irregularly shaped, with a high degree of porosity, having a maximum particle size of 3mm. Manual die compaction was conducted using a Carver hand press, in a hardened tool steel die with 12.61 mm inner diameter. Uniaxial die compaction in a hardened tool steel die with 9.50 mm inner diameter was also performed using a Gleeble® 3500 thermal-mechanical simulation testing system which allowed for controlled deformation rates. Compaction behavior of the titanium sponge was studied using well-established compaction equations (Heckel, Panelli-Filho and Ge), and it was observed that compaction rate influences the room temperature compaction behavior of this material. The Heckel analysis of the titanium sponge showed that the behavior of the material could be analyzed in two compaction pressure regimes. In the low pressure regime (<100 MPa) the granules exhibited high compressibility, while; in the high pressure regime (>100 MPa) lower compressibility of the titanium sponge was observed.

Jan 1, 2015

By C. Horstmann, D. Andreo, G. Barthold

"The concept of large single line grinding circuits provides a valid answer in project feasibility studies by reducing capital investment requirements compared to parallel lines for the same plant throughput rates. The benefits of this concept are reflected as well on the operational aspects, in terms of higher and greater process stability, and reduced operational costs mainly due to the associated lower maintenance expenditures. However, concerns exist in the minerals industry on whether large single line grinding could reduce the overall concentrator plant availability. The mechanical design and integrity, the mill and gearless mill drive integration, as well as assets management aspects of this type of equipment are the key to guarantee successful availability records. Together with an overview of the added value provided by large single line grinding circuits, this paper focuses on risk mitigation strategies during mill and gearless mill drive integration, as well as on the design of the equipment itself, for the key aspects which could put at risk the operations availability.INTRODUCTIONDespite a large long term demand for commodities, the mining industry has never faced complex challenges as it is doing today. Decreasing high-quality and accessible deposits, declining ore grades in existing mines, shortages of electrical energy (e.g. in Chile) and an aging workforce are the most significant among the megatrends affecting our industry. In addition to this, flat underlying commodity prices and high price volatility are currently posing strong requirements to miners when entering into the process of approving investments.Nowadays to get projects financially approved (optimizations, expansions, new plants), capital expenditure has to be reduced, as observed up to 30% compared to the last decade, and at the same time the plant design has to be such to demonstrate that operating costs will also be significantly lower than in the past.When it comes to the concentrator plant, the concept of large single line grinding circuits provides a valid answer in project feasibility studies by significantly reducing the capital investment requirements compared to parallel lines for the same plant throughput rates. The benefits of this concept are reflected as well on the operational costs, in terms of higher and greater process stability and reduced maintenance expenditures."

Jan 1, 2016

By W. E. Kuhn

Introduction The work, of which some of the results are described in this paper, was started with the object of investigating the properties of certain binary alloys of titanium made from powders. Our main interest was in the possible use of such alloys in gas turbines. We were attracted to titanium, as have been others, by its high melting point (I,724° ± 11°C.), its low density (4.54), and the likelihood that, if a relatively wide use could be found for the metal, it might become available in commercial quantities at a fairly reasonable price. The readiness with which the metal reacts with hydrogen, oxygen, and nitrogen was recognized from the very beginning. At the same time there seemed a good chance that alloys could be produced which, because of the formation of protective films, would resist the attack of these and other corrosive agents. No specifications were drafted to cover the &apos;quality&apos; of the titanium hydride powder which was used in our work and which was, to judge by the results of a few preliminary experiments, the most useful source of titanium then (1944) available in sufficient amount for our purpose. During the course of our work, the need for such specifications became very clear (see Sections 9 to 12 of this pa per). Even today, lack of knowledge regarding the effects on titanium of impurities, some of which may later be looked upon as essential elements in commercial alloys of titanium, and difficulties in manufacture, make the preparation of specifications for commercial titanium and titanium compounds a doubtful procedure. The papers presented at the 1948 Symposium on Titanium, sponsored by the U.S. Office of Naval Research lend colour to this view. At the time our work was commenced, one had to depend upon the manufacturer to supply what he considered to be his &apos;best&apos; material. It may be some time before we can ask for more than this, the question as to what is his &apos;best&apos; being left to the manufacturer to decide. However, in this connection the results of our study may be of some value and on that account we are constrained to publish them.

Jan 1, 1950