Search Documents

By P. Bramwell, R. Tremblay

"The Port Radium leaching plant of Eldorado Mining and Refining, Limited, produces 450 t./d. of sulphuric acid leach liquor containing l. 73 g. /I. U 308. After solvent extraction, the waste solution is discarded at 0.002 g./l. U30s for a recovery of 99.8 to 99.9 per cent. The solvent is acidified with weak sulphuric acid, loaded to 4.5 g./l. U80:1 in three-stage extraction, scrubbed with water, and stripped with soda-ash solution in single-stage stripping. Caustic removes the UaOs from the pregnant strip solution as a precipitate. The slurry is filtered, re-pulped with water, and re-filtered. The pressed precipitate at 81 to 82 per cent equivalent U30s is dried and packaged. The carbon-ate filtrate is cooled to remove sodium sulphate build-up and carbonated to convert excess caustic. Reagent consumptions are 4.1, 0.22, and 0.39 pounds per 1,000 gallons of pregnant solution for Diesel oil, amine, and alcohol, respectively. Caustic consumption averages 1.3 to 1.4 pounds per pound U3O8.Extraction and stripping is accomplished in sheet-iron mixer-settlers lined with Phenoline. Piping on both circuits is Schedule 80 polyvinyl chloride. Valves are straightway Buna N lined with American Hycar diaphagms. Extensive instrumentation ensures good metallurgy with a minimum of variations and labour. Mixing in a continuous organic medium and careful acidity control are required to minimize third-phase formations. Heating the precipitate slurry is conducive to good filtering in Perrin presses with neoprene-coated, rolled-steel sectors. Sodium sulphate is crystallized from carbonate filtrate solution by batchwise cooling to 54°F. with lake water."

Jan 1, 1959

By Limao Zhang

This paper presents a BIM-based Risk Identification Expert System (B-RIES) for metro construction, composed of three main built-in subsystems: BIM extraction, knowledge base management, and risk identification subsystems. The engineering parameter information related to risk factors is extracted from the BIM of a specific project where the IFC standard plays a bridge role between the BIM data and metro construction safety risks. An integrated knowledge base, consisting of fact base, rule base and case base, is established to systematize the fragmented explicit and tacit knowledge. A hybrid inference approach, with case-based reasoning and rule-based reasoning included, is developed to improve the flexibility and comprehensiveness of the system reasoning capacity. During the safety risk identification process, B-RIES is able to improve the inefficiencies in engineering information extraction, reduce the dependence on domain experts, and facilitate knowledge sharing and communication among dispersed clients and domain experts. A typical safety hazard identification in the Mingdu station, located in the Wuhan Metro Line Two, is presented in a case study. The results demonstrate the feasibility of B-RIES, and its application potential. B-RIES can be used as a decision support tool to provide guidelines for safety management in metro construction, and thus increase the likelihood of a successful project in a complex environment.

Aug 1, 2013

By M. Vallée

Several reviews of mineral project performance in the past 35 years indicate a pattern of occasional, but recurrent, mining project failures due to shortcomings in geological information and estimation, mineral processing and metallurgical testing, feasibility study objectives and requirements, and project start-up methods. A commitment to quality assurance and continuous improvement methods and to obtaining “ENOUGH DATA, OF APPROPRIATE QUALITY” is essential. Recent international and Canadian proposals for mineral resource and ore reserve definitions have taken a nonprescriptive stance that will undermine the formulation of requirements, guidelines and industry standards for efficient deposit delineation and estimation, and for the determination of project feasibility. To help reduce problems, every feasibility study supporting a mine development and production decision should be based on objectives and methods adequate to reach completion targets similar to the bankers’, as a good business target for a profitable project. In a resource/reserve system, the use of reserve should be restricted to a project that meets required technical, economic and legal feasibility requirements for successful project implementation, and the definitions of these categories should provide explicit limits. Current shortcomings will limit the ability of the Qualified Person to provide “adequate professional practice,” fulfill his/her professional responsibilities to his employer or client and provide adequate information to the investing public. We must take advantage of present opportunities for Setting New Standards for the new Millennium.

Jan 1, 2000

By Smortchevskyk N. J.

THIS paper describes the electrical features of the locomotive now (August, 1962) under construction for Craigmont Mines. Intended for non-specialists, it avoids details of design and calculations interesting to electricians only. The paper is divided into three sections. The first deals very briefly with the mine layout and with operating conditions -existing and expected. Reference is made to economic considerations leading to the selection of the type and size of locomotive, as well as to traction diagrams and the calculations. This material is not included in the paper because of its length and because it does not represent anything new. The second section deals with engineering and economic considerations and shows, in some detail, why the A.C. system was chosen. The third section describes the basic components of the locomotive, including the voltage regulator, the rectifiers, the control arrangement and the filter, and deals with considerations affecting the selection of their rating and design. A concluding sub-section describes, very briefly, the track and trolley details and the power distribution switchgear.

Jan 1, 1963

By Jie Li, Xinyu Liu, Yan Chen, Linjian Ma, Yasong Wang

Nonlinear time-dependent response analysis of salt cavern under extreme loads in disaster mode is of great importance to the safety and disaster prevention of gas storage group. Uncontrolled blowout is one of the extreme conditions for compressed-air cavern operation. Based on the geological structure of Jintan salt deposit, China, the numerical model of the complete process of water solution, cyclic operation, and internal pressure runaway was developed. The effects of rapid unloading on the stress filed, the progressive failure of surrounding rock, the volume convergence of storage cavern, and the ground subsidence were simulated employing an elasto-viscoplastic damage constitutive equation for rock salt. The results indicate that the damage and failure zones propagate much larger in the mudstone interlayer than in the host salt. The volume of damage and failure zones surrounding salt cavern induced by unloading process is 5~6 times that of cyclic injection and withdrawal process. The average volume convergence rate of salt cavern reaches 0.012%/d~0.013%/d, which is 6~6.5 times that induced by cyclic operation. The ground subsidence exhibits a typical funnel curve. The affected region of ground subsidence due to rapid unloading in the blowout period is about two times the maximum cavern diameters. Furthermore, double cavern analysis reveals that the interaction between adjacent caverns may be ignored so long as the pillar width is larger than two times the maximum cavern diameters.

Jan 1, 2015

Diverse and considerable energies are associated with mobile equipment operated and maintained on mine sites. Loss of control of these energies is a common cause of injury on mine sites and this is well recognised by the mining industry. In 2006, 4 multi-national mining companies formed the Earth Moving Equipment Safety Round Table (EMERST), with the aim of engaging collectively with the manufacturers of equipment to accelerate improvements in mining equipment design. Originally focused on surface mining equipment, and particularly haul trucks, the focus of EMESRT widened to include underground and exploration equipment. Since 2006, EMESRT has maintained a program of regular visits and other engagements with a steadily increasing number of manufacturers. The membership of EMESRT has also increased, with 15 companies being members in 2012. An initial step undertaken by the EMESRT members was the development of ?Design Philosophies? which drew of the collective experience of mining companies to identify potential unwanted events which cause equipment related injuries and illness. A technique for analysing risks associated with operation and maintenance tasks, the Operability and Maintainability Analysis Technique (OMAT), was subsequently developed and trialled. In 2011, the EMERST members resolved to propose a common form of safe design information to be requested by all members companies during procurement, and the resulting EMERST Design Evaluation for Equipment Procurement (EDEEP) process was launched at MINExpo in Las Vegas in September 2012. The outcomes of OMAT risk assessment and control activities are integrated during this process into a common ?Safe Design Information? template for communication to prospective purchasers. The aims of requesting manufacturers to follow this process are to provide equipment purchasers with a common way of assessing how well the issues in the EMESRT Design Philosophies are addressed in the equipment design; and to provide manufacturers with additional information for use during equipment design. The process involves identifying priority tasks based on frequency and the severity of the consequences of potential unwanted events identified in the EMESRT Design Philosophies; undertaking a task-based risk assessment of priority tasks in conjunction with site-based personnel; evaluating the effectiveness of control measures; and providing information about safe design features in a standardised format.

Aug 1, 2013

By M. Gimpel, R. Galler, T. Antretter, H. Kargl, R. Tichy, W. Ecker, M. J. Mikl-Resch, G. Pittino

"A computational method based on a continuum-mechanical approach to simulate rock cutting is developed and evaluated. The aim is to obtain the local loading acting at the cutting pick during operation. The explicit FEM is chosen to model the pick-rock interaction. The presented method takes advantage of (i) an advanced material model (ii) a robust contact algorithm and (iii) fast calculations due to parallelization. A damage-plasticity law is chosen and modified with user-subroutines. A user integrated element deletion routine evades critical mesh distortions. Infinite elements at the model boundaries avoid unrealistic deformation wave reflection.INTRODUCTIONExcavation in mining and tunneling is a costly and complex process. Special equipment such as the roadheader (Figure 1) is employed to cut the rock in the excavation process but high material strengths limit their usability (Tockner 1999). Nowadays a challenge is to extend their field of application to harder and more abrasive rock materials. The forces on the pick (Figure 2) are of great importance and determine wear and especially the efficiency of the machine. Figure 2 shows the principle of cutting and the predominant forces. The variation of pick geometry, cutting depth or attack angle will result in an alteration of these forces and determine the efficiency of the process (Tockner 1999). The mechanisms of rock cutting follow the principle of indentation (Kou et al. 1999). Directly under the indenter a hydrostatic stress state evolves causing the material to fail only due to crushing and fragmentation mechanisms. In the close surroundings large strains emerge and tensile cracks are formed but in a further distance the material behaves elastically."

Jan 1, 2015

By M. Gimpel, R. Galler, T. Antretter, H. Kargl, M. Mikl-Resch, R. Tichy, W. Ecker, G. Pittino

"A computational method based on a continuum-mechanical approach to simulate rock cutting is developed and evaluated. The aim is to obtain the local loading acting at the cutting pick during operation. The explicit FEM is chosen to model the pick-rock interaction. The presented method takes advantage of (i) an advanced material model (ii) a robust contact algorithm and (iii) fast calculations due to parallelization. A damage-plasticity law is chosen and modified with user-subroutines. A user integrated element deletion routine evades critical mesh distortions. Infinite elements at the model boundaries avoid unrealistic deformation wave reflection.INTRODUCTIONExcavation in mining and tunneling is a costly and complex process. Special equipment such as the roadheader (fig. 1) is employed to cut the rock in the excavation process but high material strengths limit their usability (Tockner 1999). Nowadays a challenge is to extend their field of application to harder and more abrasive rock materials. The forces on the pick (fig. 2) are of great importance and determine wear and especially the efficiency of the machine. Figure 2 shows the principle of cutting and the predominant forces. The variation of pick geometry, cutting depth or attack angle will result in an alteration of these forces and determine the efficiency of the process (Tockner 1999). The mechanisms of rock cutting follow the principle of indentation (Kou et al. 1999). Directly under the indenter a hydrostatic stress state evolves causing the material to fail only due to crushing and fragmentation mechanisms. In the close surroundings large strains emerge and tensile cracks are formed but in a further distance the material behaves elastically."

Jan 1, 2015

By A. Rahimi

Refractory castables based on alumina-silicate aggregates are commonly used in casting wheel components and launders. In this research the recycling process of waste magnesia chrome bricks for production of refractory castable lining for launders and casting wheel ladles at Iranian Sarcheshmeh copper complex (I.S.C.C.) is discussed. The smelting plant of ISCC consumes 4,000 tons refractory materials and produces 2,000 tons waste refractories annually. In order to reduce the environmental pollutions and gain the economical advantages, the recycling of waste refractories proved to be a solution [1]. In ISCC, 800 tons alumina or alumina-silicate refractory castables are used for linings of anode furnace ladles and launders annually [2]. In the present work, the spent bricks from reverberatory, converter and anode furnaces were analyzed in term of microstructural changes from hot zone to the cold end to evaluate the changes in texture and chemical composition. Different formulations based on recycled magnesia chrome aggregates and various particle size distribution and cement content were tested. Economic recycled magnesia chrome refractory mixture was prepared after crushing and sizing the non-deteriorated regions of wasted bricks. After evaluation of physical and mechanical properties of samples, one ton of refractory castable was prepared and successfully installed in the casting wheel ladles.

Jan 1, 2007

By James Mackie

The Vancouver Stock Exchange (VSE) has been providing venture capital for start-up companies since 1907. Ninety years' experience in the junior mining industry has enabled the VSE to develop policies and procedures tailored to the unique needs of start-up companies. Policies and procedures applicable to listed companies are documented in the Corporate Finance Services Department "Policy and Procedures Manual." Approximately 50% of the companies listed on the VSE are in the mineral exploration and development business. The largest number are exploring base metal, precious metal or diamond properties. A recent count shows that about 20 companies are exploring industrial mineral or non-metallic deposits. The minerals sought by these companies include limestone, decorative stone, building stone, lava rock, wollastonite, zeolite, garnet and graphite. There are two basic routes to obtaining VSE financing for an industrial mineral property. The owner can either sell an interest in the property to a listed company or form a company and have it listed on the VSE. In each instance, the listed company is responsible for raising funds to develop the property. A typical financing consists of the sale of company securities byway ofeitherprivate placement or prospectus offering.

Jan 1, 2001

By A. P. Sasmito

It is well known that underground miners are exposed to one of the most dangerous working environments on earth. As mine delve deeper, the geological factor, mine position and climate condition as well as heat generation from mining machine give rise to the mine operating temperature. This, in turn, has an adverse effect on the environment and thus leads to higher operating costs. Careful estimation and design of air flow rate, spray system, cooling load and additional ventilation auxiliary equipment are of importance to ensure safety, comfort and productivity whilst maintaining low operating cost. A computational fluid dynamics simulation approach is employed to examine underground mine ventilation in a 36 m cul-de-sac of tunnel of coal mine. The model predictions in the turbulent range were validated by comparison with published data. Different turbulence models were tested to select one that yields adequate accuracy and is computationally efficient. Effects of the following parameters are evaluated: tunnel geometry, air flow rate and inlet air temperature. The objective of the simulation is to arrive at an optimal strategy for ventilation and thermal comfort at low cost.

Aug 1, 2013

By R. J. McCarthy

In-pit Crushing and Conveying (IPCC) is increasingly being considered by mining companies as a means to reduce their dependence on trucks and thus, fuel, tires, labour, etc. There is potential for great savings in operating costs which ultimately can mean better economics for a mining project. Vale has considered the application of IPCC at its Moatize coal project in Mozambique. Up to three studies have been conducted with the latest, at a pre-feasibility level, showing some promise. This paper explores the mine planning and IPCC engineering elements required in an IPCC study, their application to the Moatize project, and the drivers which most impact the viability of IPCC at Moatize.

Aug 1, 2013

By Richard Dawson

Presentation Outline? Northeast BC Coal Fields Overview and History ?New mines and projects in development ?Design Issues for steeply dipping footwall slopes ?Design issues for angle-of-repose waste rock dumps

May 1, 2006

By W. S. Hegler

Introduction The San Antonio mine is on the north shore of Rice lake, thirty miles east of lake Winnipeg and 120 miles northeast of the city of Winnipeg. Since production was started in 1932, about 2,000,000 tons of ore have been mined. Currently in progress is an extensive development programme which involves 11,500 feet of crosscuts, 3,800 feet of raises, 1,753 feet of shaft sinking, and 160,000 cubic feet of slashing, all in footwall waste rock. It is the purpose of this .paper to indicate the necessity for this work and to describe the methods employed to carry it out. Where unknown factors are as prevalent as they are in the average Canadian gold mine, a definite answer cannot be given as to what is the most economical and efficient system for mining dipping deposits. At San Antonio, the host rock for the orebodies, locally termed basalt, occurs as a sill some hundreds of feet in width and dipping at approximately 45 degrees from surface to an unknown depth. It may be assumed that it continues well below the lowest depth established to date by diamond drilling. At present, a vertical winze (No. 3 winze) hoists the ore from the 2,360-foot level to the 1,600-foot level, on which it is hauled about 900 feet to No. 3 shaft, also vertical, and there hoisted to the mill bins on surface. To maintain ore reserves at a five-year figure, at full production, additional deep exploration was required immediately. It was decided to sink No. 4 winze, a vertical opening of the same size as the other operating shafts, to provide ten additional levels (17 to 26) at 150-foot intervals, with additional depth to allow for an underground crusher installation and usual loading-pocket facilities for three-ton skip-hoisting. The winze was bottomed at 1,753 feet below the collar, at a depth of 4,117 feet below surface, and is the deepest man-sized opening in Manitoba.

Jan 1, 1949

By G. Barrasso

REACH was proposed by the EU Commission in October 2003 and stands for the Registration Evaluation, Authorisation and Restriction of Chemicals. It requires that all substances identified as persistent, bio-accumulative and toxic, whether the risk of those chemicals being released is real or perceived, require registration prior to them being allowed to be imported into the European Union. An internal investigation by the metals industry indicates that almost all primary raw materials streams would be classified as hazardous due to the potential health or environmental hazard properties of one or more of their ingredients. REACH uses a wide definition for chemicals and metals and as such its implications greatly impact the entire supply chain of the metals industry. The process of registration would require the producer/ importer to produce a dossier. Initiatives along the same lines as the EU REACH are also coming up in other parts of the world. REACH requires registration of at least four substances manufactured by the aluminium industry: aluminium metal, including powder, aluminium oxide, and aluminium hydroxide. The proposed legislation permits the affected companies to band together to form a consortium to develop certain aspects of the registration application. The aluminium industry has established a consortium and testing is currently underway.

Jan 1, 2006

By F. Hashiuchi

In 1996, the Saganoseki custom smelter & refinery successfully shifted to a single flash smelting furnace operation and increased the copper production capacity to 450,000mtpy in 1998. As the next step, Saganoseki planned to further increase the productivity, especially in the area of P.S. converters and acid plant. As the results of modifications and operational improvements, the gas washing & cooling sections of the Saganoseki acid plant were consolidated from 3 to 2 lines, and increased the gas treatment capacity. The S02 converters in the acid plant were also modified to increase the acid production. By increasing the matte grade from 65 to 68%, six PS converters have been successfully integrated into four, while maintaining the production capacity and reducing the environmental burden in 2005. This paper discusses recent operational conditions and the results of implementation of technological improvements.

Jan 1, 2007

By Peter Hood

Data on world-wide geophysical activity in mining exploration programs are collected annually by the Society of Exploration Geophysicists' Geo-physical Activity Committee as part of a continuing service to the industry. The data are obtained by sending out questionnaires to all organizations which are known to be carrying out mining geophysical work; the organizations canvassed include mining companies, contractors, government departments and universities. The questionnaire is divided into three sections; namely, ground methods, airborne methods and research. The data compiled from the questionnaires show that world-wide utilization of mining geophysical methods reached a new high in 1967 with total expenditures of (U .S.) $32,323,240. This was divided as follows: ground methods, $18,106,785; airborne methods, $10,-123,405; and research, $4,093,050. For the ground methods, most money was spent on the induced polarization technique ($5,681,780); electromagne-tic methods were second in reported expenditures ($2,010,900). The total reported geophysical line mileage flown was 1,275,072 line miles, with aeromagnetic surveying being the most popular airborne method. The total amount spent on aeromagnetic surveys was $5,832,564 for 895,420 line miles. This gives an average cost of (U.S.)$6.50 per line mile.

Jan 1, 1968

By F. J. A. van Ruitenbeek, M. Dalm

In the presented study test work was performed with near-infrared hyperspectral imagery (NIR-HI) on 36 ore samples from a South-American epithermal Au-Ag mine. The aim of the test work was to investigate if NIR-HI provides information about the alteration mineralogy of samples that can be used to predict their economic value. Mineral distribution maps were produced from the hyperspectral images by using correlation coefficients between the image pixels and a set of reference spectra. These maps showed that detection of mineralogy with NIR-HI can be used to distinguish; i) ore particles with low Au and Ag grades, ii) ore particles with high carbon contents, iii) ore particles with high sulphur contents.

Jan 1, 2015

By M. L. Jeremic

The design of the long-hole sublevel mining method was originally based on the traditional assumption that the principal load was due to the weight of the overlying rock, and that the horizontal stresses are equal to one-third of the vertical stress. However, as mining progressed, the virgin lateral stress was found to be equal to or greater than the vertical stress. The virgin stress in the rock mass is not uniform throughout the folded orebody and adjacent strata. From detailed investigations, three basic patterns of virgin stress in ore panels have been inferred: uniform, bent and twisted. Stresses induced by stoping are up to three times greater than original stresses in the rock mass; they cause heavy ground conditions and make extraction of ore difficult. In the last ten years, the original mining system has been modified several times in order to destress the ground and improve the extraction of ore.

Jan 1, 1978

By E. C. W. Perryman

Materials research and development has played an important role in the commercial success of the CANDU- PHW nuclear reactor and in the production of heavy water. Both capital investment and energy conservation demand very high component reliability in such systems. The interactions among reliability, plant performance and economics will be discussed in relation to materials research and development. Likely materials requirements for the nuclear industry over the next twenty five years will also be discussed.

Jan 1, 1977