Search Documents

Subsidence prediction methods can be divided into two basic types: empirical and analytical. Empirical methods are based largely on a combination of experience, intuition and observations from a large number of observed subsidence data. They are simple in their application, but they are not based on any principle of mechanics. Analytical methods are based on equivalent material modelling principles, where the ground surrounding the extraction is mathematically represented by idealised materials that deform according to the principles of continuum mechanics. Wide applicability and improved understanding are the principal advantages claimed for this approach. In NSW, significant progress has been achieved in the area of subsidence prediction during the last ten years. Empirical prediction curves are available in NSW for predicting the ground movement in the Southern and Newcastle Coalfields. A' comparison of subsidence values predicted from these curves with the actual monitored values indicates that the curves are adequate for use in conjunction with the existing damage assessment methods. Future research for improving the existing empirical prediction curves can only be justified if it is cost effective. There are several numerical models currently in use in NSW for predicting subsidence. The models do not appear to be superior in their ability to predict subsidence when compared with the empirical curves. the performance of these models will no doubt improve along with advances in defining strata properties and failure mechanisms.

Jan 1, 1991

By S Karosiya, A Sharma, M Jain, N N. Viswanathan, M M. Pande, D Kumar, S Kumar

Desulfurisation of steel during ladle refining is governed by both thermodynamics and kinetics. For effective desulfurisation, thermodynamically, a low partial pressure of oxygen at the steel-slag interface and highly basic slag which possess a large sulfide capacity are desired. Kinetically, the mass transfer coefficient of sulfur in the liquid steel and in the slag determines the rate of desulfurisation. A fast desulfurisation rate is achieved by maintaining sufficiently strong argon stirring of the melt. In the present work, sulfur mass balance for steel and slag was performed after the desulfurisation treatment for several industrial heats. The decrease in the sulfur quantity of the liquid steel was more than the increase in the sulfur quantity of the slag. The discrepancy in the sulfur mass balance suggests that the sulfur could be transferred to: (a) the gas (via slag) phase; or to (b) the refractory (crucible) phase. The preliminary investigation of the refractory samples taken at slag-refractory and steel-refractory interface showed no interaction of sulfur with the refractory. Therefore, the possibility of sulfur transfer to the gas phase was verified by carrying out melting experiments of sulfur containing slag in an argon/air atmosphere. Sulfur containing slag was initially melted in an MgO-C crucible under an argon atmosphere followed by creating the air atmosphere just above the melt. Careful sampling and analysis from the cold spots of the crucible, much above the melt surface, revealed formation of a fibrous structure. Scanning electron microscopy energy dispersive X-ray spectroscopy (SEM-EDS) analysis of these fibrous deposits confirmed the presence of oxides and sulfides. Oxidation of sulfur containing slag under air atmosphere was also performed using a thermogravimetric analysis (TGA) set-up. It showed a constant sulfur loss in the range of 1300– 1500°C. Thermodynamic calculations carried out using FactSage™ ver 8.3 for these experimental conditions are in good agreement with the observed results.

Aug 21, 2024

By K B. Barnard, M D. Urbani

A synergistic solvent extraction (SX) system for nickel and cobalt recovery using Versatic 10 and decyl-4-pyridinecarboxylate was tested with BHP Billiton pilot plant leach solution. Another synergistic SX system for cobalt and zinc recovery was successfully tested using Baja MiningÆs pilot plant leach solutions. Synergistic SX systems have also been developed to separate iron, zinc and copper from nickel and cobalt for Minara Resources and to separate manganese from magnesium and calcium in waste stream for HiTec Energy. The gypsum precipitation problem at the former Bulong operation could have been alleviated using a Versatic 10 and CLX50 synergistic SX system. These synergistic systems have shown high selectivity for target metals over impurity metals and would largely improve SX plant operation. Maintaining a æhealthyÆ organic is very important for efficient plant operation. Careful analysis of plant organic at CSIRO has been used as a tool to pre-empt and/or solve problems in operating circuits. Work performed to assist operators has included assessing plant organic solutions to highlight impurity build-up with time, assessing reagent stability under prescribed operating conditions, correlating organic composition with impurity transfer and crud analysis. An independent estimate has determined that work in this area by CSIRO has provided over $50 M in benefits to the industry.

Jan 1, 2005

By J Safarian, M K. Kar

Bauxite residue is one of the most important by-products from the alumina industry with no commercial use till now. The utilisation of bauxite residue through pelletising with different lime additions, hydrogen reduction, and smelting has been studied in this work. Three different types of green pellets were made with varying calcite-to-bauxite residue ratio and subsequently sintered at elevated temperatures. The sintered pellets were isothermally reduced at 1000°C under hydrogen gas followed by smelting of the reduced pellets in argon at 1500°C. Smelting of the reduced pellets leads to the recovery of metallic iron and the formation of a leachable calcium aluminate slag. X-ray diffraction (XRD) and scanning electron microscope (SEM) were used to characterise the phases and microstructural analysis. The iron produced in the smelting process has a high purity, above 99.5 wt per cent. While the iron content of the slags is quite low, and the slags shows variations of krotite (CaAl2O4), gehlenite (Ca2Al2SiO7), and perovskite (CaTiO3) phases based on the variation of calcite addition. It was found that the more calcite addition in pelletising yields higher percentage of krotite phase as compared to lower calcite-containing pellets. Employing quantitative XRD analysis, the krotite phase fraction was found approximately 85 wt per cent for higher calcite-added pellet, and around 74 wt per cent for lower calcite-added pellet. FactSage™, ver 8.1 (Thermfact and GGTTechnologies) thermodynamic software was used to evaluate the obtained experimental data, they both revealed that the

Jun 19, 2024

Acid rock drainage (ARD) derived from sulphide oxidation and the associated metal leaching is the most significant environmental issue facing the mining industry today. Under given hydrological and biogeochemical conditions, the local geology and mineralogy largely control the formation of ARD. The involvement of a geologist is therefore essential in minesite ARD assessment and prevention. The relevant tasks that a mine geologist may undertake at three major phases of a mining project are briefly described. Additional knowledge that a mine geologist should acquire in order to achieve proficiency in ARD assessment is also suggested.

Jan 1, 1993

Sluice-boxes are by far the most widely used concentrating devices by small-scale operators in PNG who work alluvial gold deposits. The sluice-box designs and their operating conditions used are known to vary widely. The selection of sluice-box configuration and the operating parameters such as the water flow rate is purely based on past experience. Some use small flowrates to increase the fine gold recovery at the expense of efficient separations and capacity while others use high flow rates resulting in increased fine gold losses but with high throughput rates. Recent work has revealed that the combination of riffle height, their spacing and wash water flow rate are the most important parameters that determine the success or failure of such operations. This combination has been shown to depend on the in situ gold and gangue size distributions of the deposit being processed. This paper describes a design procedure which uses a non-linear optimisation method to determine the optimal combination of the above parameters to maximise the metallurgical efficiency of such operations.

Jan 1, 1993

By X Yang, T Zhang, Z Li, Z Yan, M A. Williams, S Qin, P Wilson

Continuous development of complex new steel grades to meet the ever-increasing demand of high performance causes recurrent issues in steel continuous casting such as surface quality defects (eg cracks, depressions, deep oscillation marks) and productivity challenges (eg faster casting, near-net shape casting). Continuous casting of steel is a highly successful metallurgical process. Much of this success can be attributed to the performance of the casting powder that is added to the top of the mould, creates a liquid slag pool as it is heated, and forms a slag film between the watercooled copper mould and steel shell during its passage down the mould. Mould powder selection is a compromise between the conflicting requirements of heat transfer and lubrication. In an EU RFCS (Research Fund for Coal and Steel)-funded project, various techniques are developed to offer the opportunity to adapt the slag film to meet the conflicting needs in different parts of the mould such that mild cooling can be generated in the meniscus, mid-broad face or corner areas whilst maintaining lubrication and offering higher cooling rates in other areas of mould. This has significant potential to address the industrial issues in product quality and productivity of continuous casting. This paper reports, as part of the EU RFCS project, the determination of crystallinity and porosity in slag films for casting challenging and innovative steel grades using new methods. In comparison with the methods such as X-ray powder diffraction (XRD) analysis and optical microscopy / scanning electron microscopy (OM/SEM) analysis that are currently adopted by the industries, EBSD (electron backscatter diffraction) has been employed to determine the crystallinity of the slag films taken from industry casters. X-ray computed tomography (XCT) plus 3D image reconstruction has been used to determine the slag film % porosity with pore volume, pore size distribution, and pore location, which can be linked with the performance of the slag films during casting different steel grades.

Jun 19, 2024

By Fazakerley VW

The Murrin Murrin deposit is located about 210 km NNE of Kalgoorlie and 50 km E of Leonora in the North Eastern Goldfields region of Western Australia at latitude 28¦ 50'S. longitude 121¦ 54'E on the Laverton (SH 51-2) 1:250 000 map sheet. The tenements are held by Anaconda Nickel NL. Geological investigations between 1994 and 1996 resulted in resource calculations being completed for the ten lateritic nickel cobalt deposits shown in Figure 1. At a 0.8 per cent nickel cut-off the resources at May 1996 for the nine deposits are 116.8 Mt at 1.10 per cent nickel and 0.082 per cent cobalt. The nickel-cobalt mineralisation is contained in a laterite profile developed over Archaean serpentinised peridotites. A bankable feasibility study has been completed and the project is scheduled to be in production by the beginning of 1998.

Jan 1, 1996

By Zhang Y. D, Zhang R. X

A new decision-making approach of artificial neural network system with hierarchic structure is presented. The fundamentals of network topology, node functions and network training are introduced. A neural network system with hierarchic struct

Jan 1, 1998

An approximate rapid design system for tunnel liners and underground structures is presented which permits the effects of structure geometry and stiffness, rock quality in terms of its deformation modulus, and the applied system loading to be entered as data to produce direct designs conforming to stress limitations, optimum reinforcement requirements and restraints on section dimensions. An 'equivalent column' concept is introduced for modelling the rock mass in contact with the structure. Only the rock treatment is given in detail but the results of sensitivity analyses, with reference to rock quality, for a typical liner design are given and these results related to a number of empirical design approaches.

Jan 1, 1976

By D Purdy, K Wilkinson, P Blake, M Fitzell, J McLellan, L Feltrin, O Dixon

The northern Drummond and Bowen basins region represents one of AustraliaÆs most prospective areas for epithermal vein and stockwork style gold deposits, with both low and high sulfidation epithermal mineralisation known in the region. 3D-GIS reconstructions, numerical and probabilistic modelling (UDEC, FLAC 3D and WofE) are used here to develop a better understanding of the controls operating on the mineral systems of the region and are aimed at enhancing predictive capabilities. An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation.

Jan 1, 2008

By Blair JR

The tunnel alignments investigated for the Gosford Regional Sewerage Scheme are located in the Terrigal Formation and are covered for most of their length by a thick blanket of soil and weathered rock. The following techniques were found to be most effective in geotechnical investigations for tunnelling in this area: air-photo interpretation, seismic surveys to pinpoint drilling targets, in-situ measurements of strength,deformation modulus and permeability in cored holes, and the construction of rock- mass models. Cross-hole seismic modulus measurements, surface resistivity soundings and electric well-logging techniques were found to have limited applicability due to adverse local conditions.

Jan 1, 1976

By Wiltshire PG

The process uses sodium hydroxide and sodium nitrate reagents as in conventional Harris refining plants, selectively removing the arsenic to the caustic phase at an operating temperature of 420-450¦C. A novel feature of the process concept is continuous treatment of loaded caustic slag for recovery of arsenic as a sandy crystal product suitable for further processing to arsenic trioxide. A large pilot plant was constructed and operated over a period of 3 years to develop materials handling techniques and equipment components and to prove the concept. Stable operations were achieved at equivalent capacities of 200 tonne/yr arsenic removal. The process is being considered in plans for expansion of bullion softening capacity at Port Pirie.

Jan 1, 1984

By Buisman C. J N, Koch R. O

Soil and groundwater beneath the Budelco zinc production plant at Budel-Dorplein (The Netherlands) are contaminated with metals and sulphate. To avoid contamination of nearby drinking water aquifers in the very distant future, a geohydrological containment system (GCS) and a microbial treatment plant for extracted contaminated groundwater have been developed. As a first step in the design of the system groundwater data from over 150 wells and geological profiles were used to model geohydrological conditions beneath the site. Several configurations of water-extraction wells were deduced from the model. Data gathered during additional fieldwork were then used to improve the model. Finally results that were calculated for the various configurations were used to select an optimal groundwater containment system. Currently some 5000 m3/day groundwater are extracted from a combination of 12 shallow and deep wells. Heavy metals and sulphate have to be removed from the extracted water before it can be discharged into the river system or used as process water. Several water treatment methods have been studied and pilot-tested at the site. The preferred and selected process is based on the activity of sulphate reducing bacteria (SRB) and combines sulphate removal and heavy metal removal in one single step. The anaerobic bacteria reduce the sulphate to sulphide resulting in the precipitation of metal sulphides. A pilot plant gave promising results and a commercial-scale plant has been designed. The proposed design has been tested in a demonstration plant which included all main process units. Test results for all process units are presented. The collected information was then used to optimise the design of the commercial-scale plant. Special attention was paid to automation and safety items. Construction of the plant was finished in May 1992. Start-up, commissioning and operational experience are reported. The concentrations of metals and sulphate in the effluent of the SRB water treatment plant are well within the limits set by the authorities for discharge to public waters.

Jan 1, 1993

By Hossaini SMF

The applicability of four empirical strength criteria for rock masses, namely, Hoek and Brown, Bieniawski - Yudhbir et al., Ramamurthy - Arora and Johnston - Sheorey et al. has been tested against the triaxial test data for jointed plaster of Paris of Arora. The following modified Bieniawski criterion shows best agreement with the triaxial test data for jointed plaster of Paris: 611=1+B(63)O.825 acm 6cm where a1= axial compressive stress at failure, MPa; a3 = confining pressure, MPa; acm = uniaxial compressive strength of jointed plaster of Paris, MPa; and B = - 3.988 + 9.674 (aim ) -0.185 The modified Bieniawski strength criterion can be used to estimate the strength of a coal pillar, based on a knowledge of stress distribution in it.

Jan 1, 1992

By R K. Dayal

Many transport tunnels show distress after few decades of construction. Owing to exorbitant cost of replacement, rehabilitation of tunnels has become inevitable and rapidly gaining attention/significance worldwide. This paper discusses the detailed planning and design of remedial measures for repairs and rehabilitation of the twin tube highway tunnel in India, at an elevation of 2200 m constructed approximately 38 years ago. The tunnel length is 2547 m having 30 m2 cross-sectional area of each tube. The tunnel is lined in stretches, totalling 60 per cent lined and the remaining portions are unlined. The tunnel has developed acute problems of rock falls, water leakage, distressed pavement and icicle formation resulting in slow movement of vehicular traffic which has also increased. Suffocation inside the tunnel caused deaths due to inadequate natural ventilation, hence artificial ventilation was deemed necessary and was provided in the restricted 28.5 m2 cross-sectional area of tunnel. The paper would be useful for planners, designers and construction engineers for setting future trends.

Jan 1, 1999

By Horowitz F. G, Lamb P

As mining operations become larger and more complex, larger volumes of geological, geophysical, and production data must be manipulated and interpreted on a day-to-day basis. Because of the large volume of data, more sophisticated data storage strategies, interpretation tools, and visualisation tools must be used by exploration and mining operations in order to remain competitive. Critical to better practice is an understanding of the basic syntax and character of geological and mining data, expressed in the form of a data model. In the short-term, a data model can be used to implement or evaluate schemes for data storage or exchange. It can be used to evaluate software. In the longer term, a data model is essential to the design of the next generation of software for 3D geological modelling. In this and the related paper (Lin et al, 1995) the data model in use by CSIRO is presented, together with: 1. examples of the use of data transfer in the linkage of existing mining software; and 2. examples of the use of the data model in software design.

Jan 1, 1995

Mining is an intensive resource development industry, where operations are often of relatively short duration and can result in dramatic impacts on the natural environment during the operational period and for many years post mining. An integral component of all mining operations is water û through exploration, resource definition, mine development and operation, rehabilitation and the long-term post-mining land use. Water is a basic requirement in the provision of worker amenities, in drilling, as a means of dust suppression, as a medium for washing or processing the mine product, and as an aid in establishing vegetation on post-mining landforms. Water also plays an important role in mobilising environmental contaminants and is the primary medium for the transport of contaminants off the mine or processing site into the wider environment. It is for this second reason that the mining industry considers water management as a key component of mine management. Cost-effective water management relies on planning that incorporates a total mine system approach commencing prior to exploration and continuing through to rehabilitation and decommissioning. One of the primary considerations that will provide confidence to both government and community at the time of mine closure and lease relinquishment, will be the evidence that any water originating from, or passing through, the mine site is of a quality that will not have any negative impact on the surrounding environs into the future. The role of vegetation in stabilising disturbances to a landscape is well known, as is the recognition of vegetation being a fundamental component of the water cycle through the physiological processes resulting in the transfer of water back to the atmosphere through transpiration. In terms of water management at a mine site, the two crucial issues are the æquantityÆ and æqualityÆ of water that enters a receiving æoff-leaseÆ catchment. In terms of tolerances of the receiving environment, the total load of potential contaminants becomes critical, a reduction in which can be achieved through reduced volumes of water discharged, reduced chemical and physical concentrations of contaminants in that water, and ideally, both. This paper examines the potential role of vegetation in reducing the quantity of water released from a site, and secondly considers vegetation in the role of influencing the quality of that water.

Jan 1, 2003

The Mineral Research Centre is located at Perth in the suburb of Waterford, adjacent to Curtin University of Technology and within a Technology Precinct which includes Technology Park. The Centre, constructed by the WA Government at a cost of $16 million and occupied in late-1994, comprises three separate buildings housing the CSIRO Division of Minerals, Curtin University's School of Chemical Engineering and the Mineral Processing Laboratory of the Department of Minerals and Energy. The emphasis on R&D at the Centre is primarily in hydrometallurgy as a result of staff expertise, extensive bench and pilot-scale facilities, track record with the industry and, very importantly, two of the occupiers being partners in the AJ Parker Cooperative Research Centre for Hydrometallurgy. Staff in the Centre have a long involvement with R&D agencies such as AMIRA and MERIWA. The hydrometallurgical focus of the Centre complements that of pyrometallurgy at the GK Williams CRC in Melbourne and the Centre for Mining Technology and Equipment in Brisbane, to ensure that the mineral processing industry in Australia has access to a complete range of expertise and facilities to serve its needs.

Jan 1, 1996

For several years, the Geology Department of the University of Canterbury has hosted a series of postgraduate projects in the field of coal studies, supported principally by the Ministry of Energy and to a lesser extent by private companies. These projects have involved mainly West Coast Coalfields, and my own studies have focussed on inorganic geochemical aspects of West Coast coals. Because of the large number of potentially important analyte elements in coal, and the wide diversity of coals occurring in the West Coast region, this project has required a substantial amount of work to be spent on sample collection, sample preparation, development of analytical methods, and actual analysis. Considerable problems must be faced at the sampling stage: Can sufficient information be obtained from whole-seam composites, or should seams be sampled in plies. Ply analysis is preferable, but results of proximate analyses are usually available for composites only. Where multi-seam drillhole samples become available (eg Greymouth Coalfield, where some holes yielded more than six sampled seams), the ply option involves a dramatic increase in the number of samples. I have attempted to strike a workable compromise between geographical coverage of coalfields, and detailed sampling of individual seams at each locality. In many cases, sample material has been used jointly with Jane Newman who has carried out petrographic studies.

Jan 1, 1985