Search Documents

By Taylor L. M

Accurate computer prediction of the muck pile produced by a conventional blast requires modeling of the physics that occurs during the rock motion phase of a blast. The ability to predict the motion and the subsequent muck pile can have a significant economic impact on the mining industry. Some of the computer programs previously used to predict rock motion employed polygonal elements with comers and sides to model the rock (Cundall, 1971; Walton, 1982; Taylor, 1983). This approach allows the elements to bulk because of the corners and the aspect ratio. However, tracking the many interactions of the comers and sides of the elements is a computationally intensive process. Several other rock motion computer programs were developed that employed spherical elements, (Schamaun, 1984; Gorham-Bergeron et al, 1987) but they lacked correct bulking mechanisms or could not be vectorized for efficient execution on vector processing machines. A new spherical element code called DMC (Distinct Motion Code) (Taylor and Preece, 1989a, 1989b) has been developed this past year. DMC was designed and written to take advantage of super-computer vector processing capabilities. The efficiency has also been increased through the use of spherical elements, explicit time integration and a new contact search algorithm. When spherical elements were chosen for efficiency, some physically correct mechanisms for capturing the bulking behavior of the rock mass also had to he developed. This paper will treat several mechanisms that were developed to allow spherical elements to exhibit correct hulking behavior.

Jan 1, 1990

By Gregg PEH, Stewart RB

Reclamation field trials commenced in 1985, two years before the granting of the Mining Licence. The level of pasture production on varying soil depths (0 cm, 5 cm, 15 cm and 25 cm) overlying both tailings and oxidised waste overburden was assessed. After seven years, the rate of increase of N, C, P and S, losses of S and P and pH changes were investigated on the plots where grass seed was sown into bare tailings. It was determined that on these plots it would take approximately 24 years to reach the original carbon and nitrogen levels at the mine site.

Jan 1, 1995

By Brant BA, Lewandowski R, Trendle M, Haughton D

There is a vast amount of geotechnical data, which can be obtained during exploration programs at new and existing mine sites. Additional information on the performance of the in-situ rock mass can be obtained from bore cores, which are usually only geologically logged and then stored. A computer based data management system for storage and retrieval of geotechnical data has been developed to access and manipulate such data.

Jan 1, 1983

Coal mining safety and health legislation is more than typical of safety legislation which has been born of adversity. Indeed, in the main it has been the child of disaster. Requirements which now appear obvious were indeed only occasioned by either social injustice or more commonly by great disasters. Even then changes were often made only after months or years of deliberation by committees. Early mining legislation in New South Wales benefited from the experience in Great Britain. The pioneers of our industry were miners from there and brought with them the basic British legislation, so we started with knowledge gained the hard way. A review of accidents statistics provides a measure of the effectiveness of mine safety legislation, but unfortunately rules cannot control human nature. Miners, managers and inspectors must work as a team to make mines safe and new legislation in New South Wales is planned to this end.

Jan 1, 1975

By Collins AR, Meares RMD, Graham JM

Exploration programs for both alluvial (placer) and hardrock platinum group metal deposits are being conducted in Papua New Guinea by a joint venture between Degussa AG and Pancontinental Mining Limited. Prospective areas were defined on the basis of ultramafic/ophiolitic source rocks shedding detrital platinoid grains. Field sampling techniques including churn drilling, together with appropriate laboratory analytical and mineralogical techniques, were developed and are contributing to the success of the exploration programs.

Jan 1, 1987

By G S. Esterhuizen, M M. Murphy, T S. Bajpayee

The strength reduction method (SRM) has been implemented in the FLAC3D finite difference software and applied to coalmine entry support evaluations. The FLAC3D numerical models have been calibrated against instrumented field sites in varying geologies, depths and field stress conditions. The calibration between the field and model results obtained a satisfactory match for rock deformation and support response. Previous research has also developed good correlations between numerical model stability estimations using the SRM and empirically derived stability estimations using the analysis of roof bolt systems (ARBS) software and the coalmine roof rating (CMRR). The purpose of this paper is to further apply the SRM to investigate how specific geotechnical and support parameters can impact coalmine entry stability. Results from different studies demonstrate how the calibrated models were used to investigate a few of the well-known questions in both mine design and support design. For mine design the impact of strong and weak beds in the roof strata, rotating the principal stresses and weakening the floor on excavation stability is investigated. For support design the impact of support length, support spacing and adding cable bolts to the design is demonstrated. These scenarios are evaluated in developmental coalmine entries for a variety of geology and field stress conditions. Stability factors are calculated for each scenario using the SRM. The SRM allows the impact of each parameter to be quantified and allows the support system to be optimised for given geotechnical conditions.CITATION:Esterhuizen, G S, Murphy, M M and Bajpayee, T S, 2014. Analysis of geotechnical and support parameters on coalmine entry stability using the strength reduction method, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference , pp 383–392 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 5, 2014

By Gadd D. E

Since October 1972, New Zealand Steel Mining Ltd has loaded around 10 million tonnes of ironsand concentrate from single-point mooring buoys located off-shore at Taharoa on the west coast of the North Island of New Zealand. Before the first off-shore loading system was installed a considerable research effort was applied to proving the slurry loading technique. Subsequently the system has been expanded and a new buoy, pipelines and pumping system were installed in early 1978. Since then 110,000 DWT class ore carriers have been loaded at rates of around 2600 tonnes per hour through twin submarine pipelines. This paper reviews the operation of the shiploading system and attempts to answer the question: "If the Taharoa operation were to be planned in 1980, would the same research spending be necessary or have published research results since, made such practical tests unnecessary?".

Jan 1, 1980

By T Ye Koltunova an, L A. Otrozhdyonnova

This paper presents the results of studies on the development of an efficient non-cyanide technology for processing massive, finely disseminated, copper-zinc ores of the Urals deposits. Copper is mainly represented by chalcopyrite and zinc û by sphalerite. The main ore mineral is pyrite, with its content in ores varying from 50 to 80 per cent. At the present time, separation of copper concentrate at the Urals concentrating plants is achieved in a lime medium by non-cyanide technology using sodium sulfide and zinc sulfite as depressors of zinc and iron sulfides and butyl xanthate as the collector. Copper content in copper concentrates amounts to 15 - 17 per cent; considerable losses of zinc are associated with copper concentrate and final tailings. Various collectors were tested during the studies: xanthates and aerofloats with different lengths of hydrocarbon radicals, thionocarbamates, Aerofine 3418A of Cytec Industries, reagent S-703G of Mineral Reagents Int, and modifiers û sulfur dioxide, sodium sulfide and zinc sulfite, with a pH of the medium varying from 5 to 12. Optimum results of copper concentrate separation were achieved in a weakly acidic medium using S-703G as the collector and sulfur dioxide and zinc sulfite as modifiers. The copper content in the copper concentrate was increased by 4.8 per cent. Total copper recovery into the copper concentrate and zinc recovery into the zinc concentrate exceeded five per cent.

Jan 1, 2005

By Y Tang, G Si

The analysis of rock fragment sizes plays a pivotal role in various stages of geotechnical and mining engineering. Traditional case-based methods often falter in addressing the variability in rock fragment images due to fluctuating geological conditions and imaging environments. To counter this challenge, AI-based models necessitate training on expansive and diverse data sets, encompassing a wide range of conditions and fragment types. However, the creation of such data sets is often hampered by financial and environmental constraints. This paper introduces a novel approach for rock fragment recognition, which leverages the power of AI for data augmentation, automated annotation and prediction. The methodology integrates three key components: Style-Based Generator Architecture for Generative Adversarial Networks (StyleGAN) for data augmentation, the Segment Anything Model (SAM) for automated annotation, and the multiscale version of you only look once (YOLO-MS) real-time instance segmentation model. The proposed method begins by training a new StyleGAN model using the original data set. It then delves into exploring the latent vectors of different rock fragment images to generate specific ‘style representations’. These latent vectors form the foundational elements of each image in a high-dimensional space, encapsulating critical features such as size, shape, texture, and colour variations. The next step involves conducting quality checks on the generated images to ensure their realism and suitability as training data. Subsequently, the augmented image set is annotated using modified SAM module, followed by training the YOLO-MS real-time instance segmentation model. The performance of this model, trained on the augmented data set, is compared with a model trained on the original data set, particularly in terms of generalisation abilities in new scenarios. The results exhibit a significant enhancement in accuracy, robustness, and generalisability of the model trained on the augmented data set, underscoring the potential of StyleGAN as a powerful tool for data augmentation in geotechnical engineering image analysis.

Sep 1, 2024

A portable surface impedance meter has been tested extensively over a wide variety of geological formations both in Australia and elsewhere. It has proved a useful geophysical too] for relatively shallow mapping (i.e less than 100 metres depth) of faults, intrusions, dykes and conductive ore veins and can be used as a depth probe for overburden and glacial ice. Case studies involving coal seam mapping at Collide (Qld. Australia), galena ore vein location at Zeehan (Tas. Australia) and glacial ice probing on the Brewster Glacier (South Island, New Zealand) are detailed. The first results of a similar unit using a lower frequency with consequential increase in depth of penetration will be presented. The application of VLF measurements to monitor blasting in mines and in the location of earthquake epicentres will also he introduced.

Jan 1, 1987

By B H. Yin, S Mendoza, M Nusheh' C W Bumby, A Zhang

Hydrogen-direct-reduction of iron ore in a vertical shaft furnace is a potential process that could significantly reduce CO2 emissions from the steel industry. This approach requires the pelletisation of iron ore fines, which then undergo high temperature induration to strengthen the pellets before they can be fed into the shaft furnace. Here we report on investigations into the disc-pelletisation behaviour of New Zealand titanomagnetite ironsand, and its subsequent induration and hydrogenreduction behaviour. Initial studies focused on the effect on pellet strength of varying ironsand particle size and induration conditions using bentonite and a commercially sourced carboxymethylcellulose binder. Green pellets formed with ironsand of average particle size of 65 μm exhibited optimal strength. The compressive strength of these pellets after induration at 1200°C for 2 hrs in air was measured to be 976 N. Interparticle bonding within the indurated pellets occurs due to a combination of titanohematite recrystallisation (from oxidation of titanomagnetite), and the formation of a liquid bonding phase due to interdiffusion with the bentonite and subsequent melting. Further investigation with various binders showed that a combination of both organic and inorganic binders was essential to achieve optimal pellet strength. Carboxymethyl-cellulose binders provides green strength, whilst inorganic binders such as bentonite promoted high indurated pellet strength. Hydrogen reduction tests in a thermogravimetric furnace showed that all the pellets could achieve a maximum reduction degree of 97 per cent at 1100°C, indicating that the different pellet preparation procedures had no significant effect on reducibility. Pellet recipes developed in this work are now being used to investigate vertical shaft hydrogen-DRI processing of NZ ironsand in a kg-scale laboratory reactor.

Sep 18, 2023

By S Nowosad, O Langefeld

The mining industry has undergone a profound and transformative shift in recent years, driven by the rapid advancement of emerging technologies such as automation, digitalisation, and electrification. These technological innovations have not only revolutionised operational efficiency and productivity but have also introduced an imperative need for new and innovative approaches to conducting mining activities. Specifically, the mines of the future face a new series of complex challenges when planning and developing greenfield or brownfield mining projects in the 21st century. These challenges include greater operational depths, higher seismicity levels, higher rock temperatures, increased environmental constraints and sustainability requirements, a higher degree of interoperability, lack of skilled workforce, and the need for sustainable and eco-friendly mining practices. Consequently, there is an essential need to formulate novel strategies and robust planning methodologies that re-evaluate how mines are planned, executed, and managed, from the early exploration stages to the post-mining era and the consequent uses of mine sites. This research focuses on identifying the factors influencing the implementation of modern technologies, such as autonomous machinery in mining operations, and their impact on mining method selection and longterm mine planning. The findings underscore a crucial need for a paradigm shift in how mines are planned and developed, going beyond mining method selection, which primarily focuses on geological and economic factors, and must evolve to incorporate the multifaceted implications of modern mining operations.

Sep 1, 2024

By Yoshii Y

Many kinds of shield machines are being driven in the soft ground of Tokyo metropolitan area. Tunnel alignments for underground power transmission lines are generally planned to pass under public roads where facilities, especially life-line facilities, are densely located. Therefore, it is frequently required to drive the shield machines along very sharply curving routes. This paper reports on the performance of the new shield machine - the Sharp Curve Excavation Shield Machine - developed by Tokyo Electric Power Co., Inc., which can freely drive along a much sharper curve than conventional machines. Some of features of the developed devices of this machine are, maximum flexing angle of 6.5 degree in all deirection at the middle of shield body, maximum bending angle of 3.5 degree in all direction at the cutter disc, and so on. This shield machine can there- fore drive along curve of minimum radius 15m. The machine was confidently applied to the const- ruction of tunnel in soft clay strata at N values 2 to 5. Outer diameter 3.7m. Length 202m. Horizontal curve; radius 15m, length 20m x 2. Vertical curve; radius 30 m, inclined driven up 29%. The behaviors of the shield machine, segments and surrounding ground were monitored during construction for safety and efficiency check of this machine.

Jan 1, 1987

This paper provides an overview of the future for underground thick seam coal mining in Australia. It reviews the available and anticipated mining systems and technologies which may be adopted to mine coal seams of greater than 4.5 m thickness, together with an assessment of the likely technological and operational risks and challenges involved. This overview of mining systems is presented in the context of both current and recently completed research projects funded through the Australian Coal Association Research Program (ACARP). The projects have been joint investigations between The University of New South Wales Mining Research Centre (UMRC) and the Centre for Mining Technology and Equipment (CMTE). Outcomes from the projects have included an appraisal and classification of underground thick seam reserves in Australia and their suitability for each mining method.

Jan 1, 2000

By Sanders GJ

Coals from the Southern Coalfield of New South Wales treated in the Port Kembla coal preparation plants of Australian Iron and Steel Pty Ltd differ substantially in their characteristics. Knowledge of, performance not only enables comparison and promotes better control, but also provides the means for predicting results. Evaluation of performance of cleaning equipment has been made in terms of probable error (Ep.) Results for Baum jigs, a Chance cone, heavy medium cyclones and water washing cyclones are examined. The efficiency factors derived from the probable error are applied to the float and sink analysis, mathematically simulating operating conditions. This method is applied to the Balgownie seam. The Balgownie seam lies between the Bulli and Wongawilli seams in the Coal measures of the South Coast and mining on a large scale began recently in the Bulli area. It is known locally as the Four Foot seam and exhibits er difficult washability characteristics, due to a comparatively high middlings content. These properties and the tively high inherent ash make careful selection of cleaning equipment essential for optimum recovery. The prediction technique is used to determine the possible results when this coal is cleaned in the Port Kembla plants. Predicted values are compared with results from full scale trial washings demonstrating the validity and accuracy of the technique. Applications of result forecasting are listed.

Jan 1, 1970

The mining industry was one of the first to be directly regulated by legislation in the 19th century when British public opinion was mobilised by reformers seeking social change. In the next wave of mining safety legislation, account was taken of technological advances in the industry, but again, the amendments were in large measure driven by public expectations following a series of disastrous mining accidents with great loss of life. The result was the prescriptive and detailed type of regulation that has, to a great extent, remained with and become a way of life in the mining industry of today. In 1970, the then British Government appointed Lord Robens, a former Chairman of the National Coal Board, to head a Committee of Inquiry to consider the arrangements then in place for preserving the safety and health of people at work and to consider and make recommendations on the need for change in the legislation governing such matters. The result was the 1972 report Safety and Health at Work which, in turn, resulted in the Health and Safety at Work etc Act 1974 (UK). This Act, which embodied the now familiar concepts of consultation with the workforce on matters relating to health and safety and the statutory application of the previously existing Common Law concept of the duty of care, became the model for much occupational health and safety legislation in many places around the world, including the various States of Australia. As a result of the `Robens style' of legislation, the regulators of the mining industry have had the opportunity to become less prescriptive and to introduce an `enabling' style in their statutes. This has not always been welcomed by the industry which has, to some extent, missed the comfort of knowing exactly what is required of it in order to ensure compliance with the legislation while appreciating the `self-regulatory' opportunities that the new style of regulation offered.

Jan 1, 1995

By Craw D

The Southern Alps in the South Island of New Zealand are currently rising rapidly as a consequence of continental collision along the Pacific-Australian plate boundary. Rapid uplift has resulted in a major thermal anomaly in the shallow crust beneath the alps. Alpine topography and associated intense precipitation, coupled with the thermal anomaly are responsible for vigorous combined topographic/convective circulation of water through the shallow crust.

Jan 1, 1995

By Fee BS

This paper describes four new families of collector products which are currently being introduced at the industrial level. A brief summary of the chemical basis behind each product family will be given. This is then followed by a selection of flotation examples which illustrate the more important use characteristics that have been observed to date. It is becoming more apparent with further testing that these four new product families can offer both technical and economic advantages to the industrial flotation process operator.

Jan 1, 1993

The new field of environmental investiga tions introduces new problems of ethics, res- ponsibility, conflict of interest and technical procedures. Such investigations involve four elements: developer, consultant, approving authority and the public. It is essential that the consultant provide technical competence, speed and efficiency, impartiality and credibi- lity. Despite allegations to the contrary, it is not in the consultant's own best interest to omit, ignore or obscure significant adverse en vironmental impacts.

Jan 1, 1975

A new classification of subduction related (epithermal- / mesother-mal) gold mineralisation styles based on the tectonic framework they occur in, has been found helpful in practice. It offers a ratio-nalisation of exploration efforts during all stages of work.Methodology on the ground during first pass- and follow up explo-ration which has been found effective for the various mineralisa-tion styles is being briefly outlined.

Jan 1, 1990