Search Documents

By L McCallum, G Dale, B Silverwood, T Roscoe, A Costin

The introduction of Progressive Closure and Rehabilitation Plans (PCRPs) in Queensland from 2019 places greater importance on planning and implementation of mine rehabilitation activities. The progress and outcomes of progressive rehabilitation activities is monitored and reported upon to demonstrate success in achieving progress towards the approved post-mining landform, and to inform corrective action where required. The requirements of PCRPs place additional emphasis on mine sites to quantify the risks of successfully achieving planned outcomes. This is particularly challenging given mined-land rehabilitation is a complex process involving decisions on multiple inter-acting management interventions, climatic conditions and spatially variable site characteristics.

Aug 2, 2023

By Hoberg H, Schnieder FU

The disposal of residues from coal preparation and processing will to an increasing extent require investigation and consideration of the environmental problems resulting as a consequence of this. Different authors (Diingelhoff and Plankert, 1983; Hasenpatt, 1985; Szczepanska and Twardowska, 1987) have concentrated primarily on the content and the mobilisation of inorganic contaminants such as chlorides, metals and heavy metals from spoil tips, while no publications have yet been found on the question of a possible emission of organic contaminants (PCB, PAH, HC HC) from processing residues. Here the flotation residues in particular are able to bind larger quantities of organic contaminants by physi-sorptive means because of their large specific surface and, after disposal, to be re-emitt than into the environment. The flotation agents used in coal flotation are mixtures of technical distillation products with a correspondingly fluctuating composition. As Hey, 1986 showed, they may contain, in addition to the main components (n-alkanes, alcohols, surfactants), over 50 individual trace substances. In conjunction with the structural-chemical similarity of the individual components, this complicates the quantitative analysis of individual components considerably. For the analysis of hydrocarbon content of flotation products by means of extraction with organic solvents in accordance with DIN 38408, H18, the difficulty arises, besides the insufficient sensitivity at low concentrations, that geogeonic hydrocarbons are extracted from the coal as. well and the analysis results are thus falsified. These problems were overcome by the application of the 14C radiotracer method where certain components of the flotation agents are marked with radioactive carbon (14C). By measurement of the radioactivity of solid and liquid samples, the concentration of the marked substance can be measured very sensitively and precisely, whereby the accumulative measurement of similar organic substances is ruled out. Thus the reaction path of certain substances in complex reagent mixtures such as flotation agents can be traced excellently and the conceivable environment burden resulting from flotation tailings disposal can be estimated. In this paper, the adsorption behaviour of typical components of coal flotation agents are investigated for different coals and types of gangue material, the reagent content of flotation concentrates and tailings, as well as the mobility of the reagents adsorbed onto solids. The knowledge of adsorption and desorption mechanisms of unpolar hydrocarbons emulsified in water to solids are also of particular interest for the understanding of processes of organic soil contamination and for the further development of washing processes for oil-contaminated soils.

Jan 1, 1993

By M J. Dunn

The geotechnical model is the cornerstone of any mining geotechnical design and as such the confidence level and reliability of the geotechnical model is paramount. The geotechnical model confidence level needs to be commensurate with the level of design that is being applied or study that is being undertaken. The geotechnical model is made up of several components and the reliability of the data underlying these components ultimately determines the reliability of the geotechnical model.Data reliability is linked to the quantity of data collected, the spatial distribution of the data collected, quality of the data collection and the interpretation of the data. In a typical project, there is an opportunity to improve data reliability through the scoping, prefeasibility, feasibility and final design and implementation stages.Currently, very little quantitative guidance exists in the literature on assessing the confidence level of geotechnical studies, although there have been attempts by various authors (Haile, 2004; Haines, Swart and Kruger, 2006; Read and Stacey, 2009; Dunn, Basson and Parrott, 2011) to qualitatively describe what level of geotechnical data is required. Recently a number of authors (Read, 2013; Fillion and Hadjigeorgiou, 2013; Thomas, 2013) have outlined methods that could be applied to assess the reliability of some types of geotechnical data that are used in the development of geotechnical models.This paper briefly discusses some of the factors influencing data reliability and the geotechnical model confidence and some of the tools available.CITATION:Dunn, M J, 2014. Geotechnical models and data confidence in mining geotechnical design, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference , pp 127–134 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 5, 2014

By R Durchholz, A-J Heiertz, R Schmitz

Mining of lignite is the largest bulk materials handling activity in Europe. In order to mine this lignite, with an average calorific value of only a third of bituminous coal in an economical way, highly efficient opencast mining technology is mandatory. The total continuous mining of overburden and lignite was introduced more than 60 years ago and was subsequently developed stepwise into the largest mass transport system of the world. In 2011, the Inden Mine, one of three RWE Power mines, stripped 90 Mbcm of overburden to produce 22 Mt of lignite. In total, nearly 100 Mt of Lignite was produced from the three mines of RWE Power in Germany. Beside bucket wheel excavators (BWE), several high-performance in-pit crushing and conveying (IPCC) systems, which allow the adoption of continuous mining systems, even for typical shovel and truck (S&T) operations, are available today. RWE Power assists operators considering a change from the S&T to IPCC technology, both in the planning process involving large-scale belt conveyor systems and later with operational know how transfer. In a number of cases, the challenges associated with this system change have been addressed and solved successfully. One key challenge is managing the development of skills for operating the belt conveyor systems efficiently. This paper compares the effectiveness of S&T to different configurations of continuous mining operation for an up to 170 m deep mine with a total annual output of 117 Mbcm. From the mine operatorÆs point-of-view, the quantity and skill level of staffing required for operation and maintenance are discussed in detail. The main conclusion of this paper is the larger the operation becomes and the longer the mine life is, the earlier fully continuous mining systems should be planned and implemented.CITATION:Schmitz, R, Durchholz, R and Heiertz, A-J, 2012. Change challenges for large open pit mines, in Proceedings Eighth Open Pit OperatorsÆ Conference , pp 103-110 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 18, 2012

The South Mine, property of Broken Hill South Limited, is situated at Broken Hill, NSW, Australia, towards the southern end of the main lode. The leases (MLs 7 and 8) cover a length of 2400 feet along the lode outcrop and the workings extend, at this date, to a depth of 1940 feet below the collar of the original main shaft and to 825 feet below sea level. Mining operations have been continuous for about 58 years and during this period nearly 12.5 million tons of ore have been mined. The monthly tonnage extracted approximates 30 000 tons in normal times.The ore is a mixed sulphide containing galena and marmatite; the gangue minerals are principally calcite, rhodonite, quartz and garnet. A typical assay for a monthly period is 14.4 per cent Ph, 5.6 ozs Ag, and 11.6 per cent Zn. The whole of the ore is concentrated on the property by combined gravity and flotation methods. The lead and zinc concentrates produced are railed to other centres for the extraction of the contained metals.

Jan 1, 1994

Direct measurements of liquid contents in foams obtained from (x-terpineol a-T) n-pentanol (AmOH) and n-octanol (OctOH) solutions were carried out using a column of special construction. The column enables to determine the liquid contents by cutting-off foam layers of various thicknesses and measuring amounts of liquid contained in the cut-off foam layers. Liquid contents in the whole foam layers, in the top foam layers of thickness 14 ¦ 1 mm and distribution of water alongside foam height were determined. The average liquid contents were high and reached a level of 30, 35 and 40 per cent for foams formed from cc-T, AmOH and OctOH solutions, respectively. The liquid contents in the top foam layers were much smaller. They were of an order of five per cent for a-T and AmOH and 12 per cent for OctOH. On the basis of the liquid distribution alongside foam height some practical conclusions concerning possibilities of minimising amounts of liquid contained in the collected concentrate are presented.

Jan 1, 1993

By D J. Bradshaw, B Lottermoser, A Parbhakar-Fox

"Best practice for acid rock drainage (ARD) risk assessment still relies solely on the geochemical properties of sulfidic rocks and mineral processing products, despite the fact that a rockÆs tendency to produce acid also depends on mineralogy and texture. Consequently, there are a plethora of geochemical tests routinely utilised by the mining industry to predict ARD formation. Due to limitations associated with these tests and their relatively high costs, analysis of recommended best practice sample numbers is rarely achieved, reducing the accuracy of waste management plans. Our research addressed this through examining the application of geometallurgical data for predicting acid formation, and led to the identification of potential environmental geometallurgy indicators.Samples obtained from an iron-oxide copper gold deposit were subjected to the geochemistry-mineralogy-texture (GMT) approach, an improved methodology for classifying acid forming potential. GMT results were compared against geometallurgical and assay data sets to evaluate: relative carbonate content measurements (measured by HyLogger) and identify how these could be used to calculate effective acid neutralising capacity mineral hardness (measured by EQUOtip) to determine application of this data for calculating lag-time to acid formation opportunities to automate the acid rock drainage index (ARDI) using classified images produced by a GEOTEK logger and automated microscopy.Links between the GMT approach and geometallurgical data sets were identified. Classified mineralogy data has application at stage one, HyLogger and EQUOtip at stage two and computer-based ARDI evaluations of classified images at stage three. Through such integration, ARD characterisation costs can be reduced, with value added to geometallurgical data sets. Furthermore, deposit-wide ARD domaining is possible, and acquisition of total-orebody knowledge more likely. Through adoption of this environmental geometallurgy approach, a better informed waste management plan can be formulated, allowing for best practice ARD sampling in a more cost-effective manner.CITATION:Parbhakar-Fox, A, Lottermoser, B and Bradshaw, D J, 2013. Cost-effective means for identifying acid rock drainage risks - integration of the geochemistry-mineralogy-texture approach and geometallurgical techniques, in Proceedings The Second AusIMM International Geometallurgy Conference (GeoMet) 2013, pp 143-154 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Sep 29, 2013

Dust emissions from mining, material processing and ship loading operations (fugitive dust sources) are an environmental issue of increasing concern to both government regulators and the community. The main concerns relate to potential amenity, health and environmental impacts from the emissions. Therefore it is imperative that mining/ processing operations, as part of their overall environmental management, reduce fugitive particulate emissions to as low a level as is practicably possible. This technical paper outlines the mechanisms that lead to fugitive particulate emissions, the importance of understanding the exact cause of fugitive emissions, monitoring methods that can be used to quantify the emissions from specific sources, the use of atmospheric dispersion modelling in dust management and innovative dust management strategies including predictive meteorology and proactive management.

Jan 1, 2009

By L Dzinza, K C. Corin, M Tadie

The recycling of process water comes with increased electrolyte concentrations that affect water quality, which may in turn affect the flotation performance of valuable minerals (Hirajima et al, 2016). Electrolytes such as Ca2+, SO4 2- , Mg2+ and S2O3 2- have been surmised to have an impact on the action of flotation reagents such as collectors (Ikumapayi et al, 2012). Xanthate collectors are known to play a significant role in imparting hydrophobicity on mineral surfaces to enhance their flotation. The interaction between minerals and xanthates is well known to be electrochemical in nature. Such redox processes may be elucidated by electrochemical techniques. Since the mechanisms involving the interactions between electrolytes in process water with sulfide minerals and the subsequent adsorption kinetics of collectors are not well understood, this study therefore aims to provide fundamental knowledge to unpack the mechanisms involved when electrolytes interact with Platinum Group Minerals (PGMs) and how these interactions may affect xanthate adsorption. The interaction of sodium iso-butyl xanthate (SIBX) in the presence of electrolytes at increasing ionic strength was investigated by rest potential measurements, to explain the impact of electrolytes on the adsorption of SIBX on PGMs in the flotation process. Rest potential measurements for PdTe2 and PdS were conducted in an air saturated 0.05 M di-sodium tetraborate decahydrate solution, in the absence and presence of SIBX and electrolytes. It was found that the existence of sulfide and telluride on palladium affects the mechanisms in which electrolytes interact with Pd mineral surfaces. An increase in the ionic strength of Na2S2O3, CaCl2 and MgCl2, increased the interaction between the salts and PdS, thus decreasing the extent to which SIBX interacted with PdS. An increase in ionic strength for Na2S2O3 increased the interaction between Na2S2O3 and PdTe2 and therefore decreased the extent to which SIBX interacted with PdTe2. Other salts investigated in this study increased the rate of oxidation of PdTe2 with an increase in ionic strength thereby enhancing the interaction of SIBX and PdTe2. This study has shown that mineral type, electrolyte type and concentration all have an impact on the mechanisms that result in the adsorption of SIBX on PGMs.

Aug 24, 2022

By Mahony BK

This paper discusses the major infrastructure elements required to support a typical Australian mining development. Infrastructure elements are grouped into four major types, urban planning, transportation, power and communications and water supply. The design criteria applying to individual elements within these groups are briefly discussed as well as order of magnitude cost estimates. The use of simulation models to test the capacity of existing rail networks, as well as novel sources of energy generation, are also described.

Jan 1, 1983

By S Juras

The terms measured resources and proven reserves denote the highest level of estimation confidence in all of the major classification schemes. But what do they really bring to today’s project or mine with respect to production planning and expectations? Initial reserve declaration does not need measured resources, just indicated resources. Economic viability of a project is assessed on total reserves with nary a bonus for the amount of proven reserves. Production plans are based on grade and tonnage goals that may only coincidently correspond to proven reserves. So are the measured and proven categories still relevant? Historically, and almost exclusively in underground mines, companies only allowed mining in areas of proven reserves. Some companies still follow that philosophy. But many others will mine a mixture of probable and proven reserves without hesitation. Also what of the undeveloped project in a new district – what is to be made of their declared measured resources and proven reserves? Measured resources are commonly set either by some type of proximity to data scheme or a matter of ‘feel’ based on the qualified person’s experience. The parameters for reserve conversion focus on the project as a whole and then a portion becomes classified as proven reserves almost solely based on whether the resource category is measured. So should the mining industry continue to use these categories of resource and reserve classification? This paper will present arguments about making these categories once again more relevant. A more disciplined usage of these categories may re-introduce their relevancy in public disclosures of resources and reserves. As well a more consistent usage in operations may lead to increased confidence in managing production targets and costs.

Aug 22, 2011

By M Qiao, A Sugden, W Zong, J Hines, J Roberts, T Ren

Long-term exposure to respirable dust continues to present an occupational health and safety hazard to mine workers in underground mines. Workers who are exposed to mine dust can develop occupational lung diseases including coal workers’ pneumoconiosis (CWP) or ‘black lung’, progressive massive fibrosis (PMF) and chronic obstructive pulmonary disease (COPD). To demonstrate the exposure impact of certain working conditions and improve dust management in longwall development panels, this paper details the development of a computational fluid dynamicsvirtual reality (CFD-VR) based training tool. The tool has been developed as an educational platform to facilitate the effective communication of workplace health and safety (WH&S) dust control measures for continuous miner operators and engineers. The study introduces a promising approach to model ventilation and dust flow patterns based on site-specific data, employing computational fluid dynamics (CFD) for a detailed analysis and visualisation of these mechanisms. Additionally, an algorithm has been developed for processing the large and complex CFD data sets into a form amenable for visualisation within a virtual reality (VR) environment using standalone VR headsets with limited processing power. This training tool has been deployed to mine sites with the specific purpose of educating users on the hazards of dust emissions and the best practices for control.

Apr 16, 2024

By Swann CA

In order to meet export sales requirements from 1983 onwards, Amcoal developed a new underground mine in the Witbank area of the Transvaal. The mine was required to produce 5 million tons of run of mine coal per annum giving rise to 4 million tons of saleable products. A description of the coal processing plant is given with comments on design philosophy and design parameters. Main features of the coal processing plant are the raw coal handling facilities, centralised control and data capture and the loadout station. The management systems applied during the commissioning period are described. The difficulties experienced and their solutions are discussed. Commissioning was concluded with an independent plant performance test.

Jan 1, 1986

By S H. Burgmans, B Anderson

This paper aims to define the specific challenges relating to dredging fine tailings from an above ground storage facility for transferral to a mined-out pit. In addition, it compares dredging and mining perspectives on dredging of fine tailings.

Jul 1, 2021

By O Otgonbayar, B Bayarmaa, D Batbyamba, S Amar-Amgalan, K H. Natsagdorj, J Nomin-Erdene, B Boldkhuu, T S. Sainzaya

The Argyle deposit in the Kimberley region of Western Australia was the world’s largest accumulation of natural diamonds. Following its discovery in 1979, the mining of associated alluvial diamonds commenced in 1983, followed by the pipe in late 1985. Over the life of the mine to its closure in November 2020, Argyle produced approximately 900 million carats of diamonds. Argyle diamonds are distinctive in having a predominance of brown colours and rare highly-prized pink diamonds, which are a signature of the deposit. The 3D geological model developed from mining and deep drilling shows that Argyle is a composite pipe formed by the coalescence of several steep-sided diatremes, each with their own feeder zones at depth, that were erupted along a NNE-trending fault. The ~1.2 Ga Argyle pipe is comprised of diamondiferous olivine lamproite volcaniclastic rocks and intruded by sparse olivine lamproite dykes. The volcaniclastic rocks are predominantly comprised of unconsolidated quartz-rich lapilli and coarse ash deposits formed by numerous phreatomagmatic eruptions of olivine lamproite magma through Mesoproterozoic water-rich sands and silts. Post-emplacement deformation has tilted the orebody 30° to the north and regional strike-slip faulting has offset, segmented, and elongated the orebody. Recent significant modifications of the geological model resulted from underground block cave operations, producing several critical lessons learnt. Diamond grade and quality reconciliation issues warranted a geological investigation which resulted in the recognition of new volcaniclastic olivine lamproite domains with a broad range of diamond grades, including some very high-grade units. The new lamproite domains had a significant effect on the block cave mining and resultant recovery of diamonds. The new findings enable a more coherent and detailed geological understanding of the volcanic emplacement and paragenetic sequence of the Argyle AK1 pipe. Structural modelling of the deposit also played a major role in the block cave mining tonnage recoveries and daily operations. The re-examination of the geology of the Argyle pipe and the results of this new information reinforces the need for ongoing robust geological work both in the early stages of mining a deposit and continued during the life of the mine.

Mar 22, 2022

By N Fullelove

The Renison Bell Tin Mine on the West Coast of Tasmania has recently installed a new underground ore handling system incorporating underground crushing, conveying and hoisting facilities. Contracts for the sinking of the shaft and the development of the mine were let and managed by the operator, Renison Limited. Hardcastle & Richards was responsible for the design, procurement and construction management of the fixed plant and equipment including civil, structural, mechanical, electrical and instrumentation services. The system demonstrates worldÆs best practice in design and incorporates a state-of-the-art integrated control system allowing the entire system to be controlled by a single operator located in the underground crusher chamber. A rapid construction period was achieved, despite the difficult and constrained underground environment, without affecting the ongoing operations of the mine. The mine, which was established in the mid-1960s, had previously operated by trucking ore to the surface via a decline. Truck haulage distances and costs had increased as the mine became deeper over the years. By the 1990s it had become apparent that, in order to remain economically viable, it was necessary to reduce truck haulage distances and allow the mine to go still deeper to access orebodies such as Rendeep beneath the current workings. The Internal Shaft System achieved this by eliminating approximately 5 km of truck haulage. It allows the production rate to be increased to up to 1 Mtpa compared with a limit of 628 kt per annum by direct truck haulage to surface. The access it provides to the Rendeep ore and other deep orebodies greatly increases the amount of ore which can be economically mined.

Jan 1, 1998

By H Han, d S. Hapugoda, L Lu

With the recent rapid development of Chinese steel industry, the world iron ore resources of good quality are depleting rapidly. As a result, iron ore deposits of lower quality have been or are being developed to meet the market demand and are becoming increasingly important to iron and steel companies. As concentrates have advantages of high Fe grade and less harmful impurities, they are ideal sweeteners to maintain sinter grade and quality when high proportions of low-grade ores are used in the sinter blends. However, due to their fine nature, addition of concentrates will inevitably increase the proportion of adhering fines and reduced the proportion of nucleus particles of the sinter blends, which can adversely affect the green bed permeability and sintering productivity. In the present study, lab scale sintering tests were carried out under the conditions similar to the sintering process to examine the effect of concentrates on the high temperature sintering characteristics of sinter blends and the structure and strength of the resultant sinter analogues.

Sep 18, 2023

By B A. Wake, G G. Lowder, M J. White

The Tooloom gold field is located within the New England Fold Belt in the far northeast of New South Wales, approximately 130 km south southwest of Brisbane. Gold was first discovered at Tooloom in 1857. Within a few years up to 10 000 people were mining placer gold deposits in the Tooloom valley and a few tried their hand at mining hard rock occurrences as well. Mining of alluvial gold continued in a small way at Tooloom until very recently, but only in the last few years, since Malachite Resources acquired its interest at Tooloom (now 100 per cent), has the full potential of this large, reduced intrusion-related gold field been appreciated. By the mid 1870s, once the alluvials were largely worked out, most of the early miners had made the 270 km trek north to the newly discovered Gympie gold field and Tooloom slipped into obscurity. Such was this obscurity that the Tooloom gold field was not recorded on published Government geological maps until 2001, four years after Malachite became involved. The many hard rock prospects that Malachite has identified in recent years were largely or completely unknown. Tooloom is a good example of blinkered thinking when it comes to modern mineral exploration. The New England province in NSW has long been the æpoor relationÆ to the much better known and more highly favoured Lachlan Fold Belt in NSW. It has also suffered serious neglect compared with the Queensland part of the New England Fold Belt that hosts such major gold deposits as Mt Morgan (>7 Moz), Gympie (>3 Moz) and Cracow (>1 Moz). Tooloom is proof that prospective geology does not stop at state borders.

Jan 1, 2004

By Equivar J, Mirabal C, Pyper R

In 1984, work was started to determine the viability of heap leaching silver-containing waste dumps from Cerro Rico near Potosi - Bolivia, at an elevation of 4300 meters (14 100 ft.). The result today is an unusual heap leach utilizing fine crushing, grinding, and agglomeration to process 1000 tonnes per day of ore containing 200 g/tonne silver. The unique metallurgi- cal, economic, and political factors will be discussed which led to the decision to build a heap leach rather than a conventional agitation leach plant. Capital and operating costs will be given along with some of the uncommon process design and equipment problems encountered while developing the operation.

Jan 1, 1991

By K Grohs, A Satriawan, S R. Pearce

Martabe gold and silver mine is operated by PT Agincourt Resources (PTAR) and is situated in northern Sumatra and comprises several deposits in steep terrain, and in a tropical climate, that are required to be developed in the optimal sequence for the best possible Net Present Value (NPV) return on the project. In addition, the waste rock from excavations and tailings from processing is a by-product to be scheduled and used for a number of purposes identified as part of life-of-mine planning. These uses include construction of the current integrated tailings storage facility (TSF) as well as future engineering construction and waste disposal projects which includes plans for a program of in-pit backfilling. These plans need to be aligned to ensure the waste rock and tailings can be contained relative to the production rate. Given that the site will have multiple open pit voids upon cessation of mining activities opportunities for integration of in-pit disposal of mine waste have now been assessed with technical studies to review the practicality of the approach with respect to operational challenges and conformance with closure planning requirements. This includes assessment of disposal of waste rock, tailings (including consideration of filtered tailings) and co-disposal of waste rock and filtered tailings.

Aug 2, 2023