Search Documents

The overall systems approach to blast furnace aerodynamics is explored including the time and spatial inter-relationships that exist between the furnace lines, tuyeres, burden characteristics, distributor capabilities and furnace operating practice. Attention is called to the time dependent, three dimensional aspects of blast furnace aerodynamics and to the existence of several zones within a furnace where the flow characteristics are different. Changes in furnace operating practice to take further advantage of fully beneficiated burdens including formed coke are discussed from a practical viewpoint. Lessons learned in a variety of shaft furnaces used for other purposes are discussed insofar as they have a bearing on aerodynamics in an iron blast furnace. Questions are raised about the penetration of hot blast in large furnaces. Operating practices and.proposed solutions are evaluated where tuyeres over iron and slag notches are restricted or plugged. Opportunities are presented for using on-line hierarchical computer systems with adaptive tuning algorithms to provide non-linear control of changing process conditions in real time. This will make it possible for the blast furnace operator to optimise a variety of interrelated paramaters, each with different response times. Potential increases in productivity, fuel savings and improved quality control are believed to be within reach.

Jan 1, 1975

The program, WASTRT 70, was set up specifically to handle the design of tunnel liners and underground structures where inter- action between rock and structure significantly affects the design. It may however be used for any mass/R.C. structure capable of being simulated by straight line elements between modes and with loading restricted to nodes. The analysis system adopts typical elastic/stiffness matrix methods. Two main mass/R.C. design segments are utilized (1) Design of section depth based on maximum required stresses and optimum steel/concrete ratios. (2) Design of reinforcement for a given section depth with concrete stresses given for mass and water code structures. Each design segment covers shear, minimum principal stress on ~ , heavy compression as per code (columns), heavy compression one-face steel (tunnel liners), tension and water code requirements for all moment/thrust/section depth ratios on rectangular sections.

Jan 1, 1976

By Palmer W. T

The successful re-opening of the Cobar min- eral field was dependent upon the success- ful introduction of highly productive, low cost mining. Mechanised cut and fill stop- ing with incline access was selected for the C.S.A. mine because it permitted flexi- bility, complete primary extraction with no secondary pillar recovery, minimised dilu- tion and oxidation, a minimum of pre-pro- duction development and because diesel powered load-haul-dump (L.H.D.) units were proving reliable and highly productive in the U.S.A. Although L.H.D. vehicles are the key to the success of the mining method, four other main groups of vehicles are utilised in the mine - trucks, scaling vehicles, ser- vicing vehicles and specialist vehicles. The operating requirements at the C.S.A. mine are more stringent than those encount- ered in many other underground mining oper- ations. The first L.H.D. vehicle used at Cobar - the Transloader - had considerable difficulty in loading and discharging coarse production ore. The Wagner ST5 Scoop Tram performed this duty much better. However, the first generation Scoop Trams were not robust enough to withstand the heavy duty and many modifications were necessary before acceptable availabilities were obtained. Similar modifications were necessary for the Eimco 916 vehicle but the Eimco 915 unit came much closer to meeting the duty requirements. Eventually Cobar technical personnel design- ed a L.H.D. vehicle to meet specific C.S.A. mine conditions. These units have proven most satisfactory. Over 8 years of operation the underground vehicle fleet has become a proliferation of vehicle types. A standardisation pro- gram has been initiated based upon common prime movers being mated with "trailer" units to serve specific functions. Standardisation will reduce inventory levels and facilitate training of operating and maintenance personnel.

Jan 1, 1973

By Kelley BC, Filmer AO

The chemical oxidation kinetics of sphalerite by Fe(III) was studied at various temperatures and size fractions in sulphate media. The kinetics of Zn extraction followed a pore diffusion control mechanism with an apparent activation energy of 54-58 kJ mole. This figure, although high for a pore diffusion control process, is consistent with other studies carried out in sulphate media. An empirical statistical model, relating the extraction time to % Zn extraction, average particle size and temperature, is described by log 1 = 12.22 - 0.017% Ext. - 1.76 log D Av t - 2954 T Parallel studies were also carried out investigating the biological oxidation of sphalerite utilizing the acidophilic autotrophic bacterium Thiobacillus Ferroxidans. The effect of such kinetic parameters as pulp density, particle size and Fe(III) on bacterial growth rate and consequently zinc extraction rate, were studied and where appropriate, optimum conditions for bacterial growth were specified. Based on the results of chemical and biological leaching studies, it was apparent that rapid zinc extraction from sphalerite was predominently due to oxidation by Fe(III). The biological oxidation process catalyses the oxidation and regeneration of Fe(III). The proposed combined chemical-biological leach system was simulated in semi continuous fashion. The sphalerite oxidation rates obtained in this system were similar to that predicted by the chemical leach empirical model. 1. Senior Research Metallurgist, CRA Research, Boolaroo, N.S.W. 2. Group Leader-Hydrometallurgy, CRA Research, Boolaroo, N.S.W. 3. Senior Research Scientist, Biotechnology Australia, Roseville, N.S.W. 4. Senior Experimental Officer, Biotechnology Australia, Roseville, N.S.W.

Jan 1, 1986

The winning and upgrading of mineral raw materials necessarily includes size reduction, which serves the liberation and production of marketable products from highly valuable and bulk materials. For crushing, the following factors can be duly accounted for depending on material type and the selection of the suitable machine: ò producing a particular size distribution, ò producing a particular grain shape, ò selective comminution, ò gentle comminution, and ò producing a size range required by a specific process and/or for a specific product.

Jan 1, 1993

There is no other effective way for study ing firedamp and coaldust explosions than to produce controlled explosions in a pre-monitor- ed environment - either mine openings kept for the purpose, or special surface galleries. Such explosion testing facilities have been employed historically at Buxton in U.K., with lesser known installations at Bruceton, U.S.A., Tremonia, West Germany, Katowice-Mikolow, Poland and elsewhere. Both firedamp and coal dust explosions are studied. Normally coal dust explosions are initiated by somewhat standardised methane air mixtures, by explosives, or purely by coal dust. Various structures and suppression installations are installed in roadways and galleries prior to explosion to simulate destruction and suppression, and the results of such tests form the basis of suppression installations, especially stone dust barriers and water barriers. Other data collected from these experiments include rev- ersals of explosion waves, pressures and temperatures and duration of explosion waves, analyses of aftergases etc. Other uses of explosion testing galleries include testing of explosives, electrical equipment and frictional . sparking.

Jan 1, 1981

By D R. Andrew, K T. Morrison, J F. Tiedgen

Waste blasting in iron ore operations can pose a number of technical challenges, including blasting through variable geology and blasting soft ground in wet conditions. Blast patterns are designed to be loaded with a specific range of explosives with unique characteristics and properties. Each explosive product will produce an optimal blast outcome for a given set of blast parameters and ground conditions. Sites characterised by softer rock typically require low-density, low-energy explosives. Historically, these products have contained a high ratio of porous ammonium nitrate prill and are only suitable for dry blastholes. When blastholes within a pattern are found to be unsuitable for such explosives due to wet, damp or muddy blasthole conditions, a new product is selected. While it is easy to switch products to match blasthole conditions, the different properties of the new non-ideal product can impact blast performance and increase loading times and costs.Flexigel™ is a solids-sensitised emulsion blend suitable for loading at variable densities and energies in dry, damp, muddy or wet blastholes. It is a universal product that can be loaded to match ground and blasthole conditions or complement other explosive products.At Fortescue Metals Group’s Cloudbreak site, Flexigel™ was trialled through a series of matched pair blasts in order to optimise blast outcomes in conditions that were non-ideal for existing explosive products and to reduce the overall cost of drill and blast operations. Flexigel™ yielded improved instantaneous dig rates and improved loading efficiency when compared to a traditional emulsion blend. The results also indicated that variable-density and variable-energy products afford greater flexibility for optimising blast outcomes across all ground and blasthole conditions trialled.Trials of Flexigel™ at Cloudbreak have shown that a variable-density solution is available for conditions where traditional explosive products are non-ideal. As such, Flexigel™ is able to fill a major void at any operation where the desired low-density, low-energy explosive product must be substituted for a more expensive traditional emulsion blend or heavy ammonium nitrate/fuel oil.CITATION:Andrew, D R, Morrison, K T and Tiedgen, J F, 2015. Flexigel™ – a variable-density solution, in Proceedings Iron Ore 2015, pp 413–418 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By Mckenzie CK, Leach KR, Bateman KW

Modelling of industrial coal flotation based on data collected in several Central Queensland flotation plants and supplemented by laboratory data is discussed. The model is kinetic in form and provides the basis of an automatic control system. The important features of the model are, 1. a distribution of flotation rates for each species of particles corresponding to the range of particle sizes, 2. a physical restriction on the removal rate of solids in cells where froth 'overloading' occurs. In this condition the removal rate of solids is proportional to the removal rate of water, 3. enhanced particle floatability due to increasing collector addition where froth overloading does not occur, 4. a second mechanism of recovery of all particles by mechanical associ- ation with water. This mechanism is particularly important in the recovery of fine high-ash species.

Jan 1, 1978

By Weller K. R, Stewart P. S B, Restarick C. J

The performance of the Renison tin concentrator was assessed in detail for two arrangements of the three available ball mills. With two mills used for primary grinding and the third for regrinding table tailing, the concentrator recovered 65.3 per cent of tin in the three tin concentrates produced by tabling, vanning and flotation at a calculated overall grade of 37.5 per cent tin prior to batch dressing. In the second arrangement one mill was used for primary grinding and two mills for separate regrinding of table tailing and sulphide concentrate. The metallurgical effective- ness of the change was somewhat obscured by unintended changes,i.e. an increase in the assay of the fresh feed from 1.38 per cent to 1.1+6 per cent tin and unresolved changes in the sulphide rougher flotation and tabling. However, using the results from a detailed size by size analysis of the behaviour of ore components in appropriate parts of the plant, it proved possible to show that, had the two unintended changes not occurred, up to 5 per cent

Jan 1, 1977

By J Bower

The JORC Code does not specify a definition for ælevel of confidenceÆ. The common approach in the mining industry is to use a certain drill spacing or number of data samples to classify resources by the confidence categories. Another approach includes application of the quantitative geostatistical criteria for non-subjective and consistent definition of the resource categories. This approach, which has become increasingly popular in the mining industry, provides a quantitative measure of the resource estimation uncertainty. In this study, uncertainties associated with the different drilling grids at the Weipa bauxite deposit (Queensland, Australia) have been modelled using conditional simulation methodology. Criteria used at Weipa for defining resource categories are as follows: mineralisation can be classified as a Measured Resource if tonnage and grade of its volume representing three months of production can be estimated with a precision error not exceeding ¦10 per cent (at 95 per cent probability, ie two standard deviations); and mineralisation can be classified as an Indicated Resource if grade and tonnage of its volume representing annual production can be estimated with a precision error not exceeding ¦10 per cent (at 95 per cent probability). Several different grids have been created by subsampling the drill hole database. The studied variables include Al2O3, SiO2, thickness of the bauxite seam and location of the footwall contact. The variables have been modelled by sequential Gaussian simulation. Based on this study the following drill spacings have been recommended: Measured Resources û 150 m by 150 m, Indicated Resources û 300 m by 300 m.

Jan 1, 2009

By Liu Y

Mathematical modelling of scrubbers in development and longwall operations in underground mines produces useful results. Mathematical modelling on the mounting of scrubbers on longwall supports shows that the number of scrubbers and the air quantity through the scrubber are the two important parameters. Increase in both these parameters results in decrease in dust levels at the tail gate. The critical factors are scrubber efficiency and the ratio of the air through the scrubber/total air quantity.Results of parametric studies conducted to establish factors which have dominant influence on the effectiveness of the scrubbers on dust levels and high gas build-up in the scrubber show that for use of scrubbers in development headings, the order of importance of parameters in relation to dust concentration in the scrubber area is: scrubber efficiency, rate of production, specific dust make/tonne, leakage factor, intake dust concentration, recirculation factor and air quantity through the scrubber.The equations developed for mathematical analysis and the detailed results of modelling provide useful data on recirculation of emitted gas in the use ofscrubbers for dust control.

Jan 1, 1995

By O Dominguez

Mine value chain reconciliation (MVC) is a necessary procedure to evaluate a mine’s performance against the assumptions and models used to plan mining and processing operations. Using nomenclature from Parker (2012), F2 reconciliation is the ratio between material received at the mill, compared with material sent to the mill, commonly reported in terms of tonnes, grade and metal. Measurements of material sent to the mill can be estimated in many ways, including: fleet management system (FMS) records, truck counts, or volume reduction. Most time-based reconciliations (for example, month-end reconciliation) use short-term model depletions of in situ rock measured by periodic topographic scans or surveys.

Mar 22, 2022

By Ahmed M, Leung L

A program of microseismic noise monitor ing for gas outbursts, in conjunction with other mining engineering measurements and observations, is being undertaken at Leichhardt colliery in Queensland. Headings are developed at present by shotfiring. The equipment being used in this study includes piezoelectric accelerometer assemblies to detect microseismic noise which is then transmitted to a surface base station by cable. Data are recorded on an analogue magnetic tape recorder and are also analysed on-line using a commercially-available acoustic emission pulse analyser. It is proposed to re-interpret recorded data using various modes of analysis and to interface a desktop computer to the existing system to permit continuous monitoring on the mine site. No outbursts have been recorded or analysed and only a limited number of develop- ment shots, and the resultant microseismic activity, have been recorded to date.

Jan 1, 1980

By Walton M. C

A combination of flotation and smelting technologies is proposed as a cost-effective means to maximise the revenue of base metal operations. The proposed treatment route breaks the grade - recovery nexus associated with the treatment of ores exhibiting difficult mineralogy in conventional plants. Aspects of the two technologies are reviewed and typical capital and operating costs presented. A significant improvement in revenue is demonstrated in a worked example, where a copper-lead-zinc operation is examined in terms of the conventional and proposed treatment options. For the selected ore, the net smelter return per tonne of mill feed improved 57 per cent, from US$89.70 to US$141.10 with the proposed treatment option. This represents an additional US$51.4 million in annual revenue. Metallurgical operating costs increased by US$20.12 per tonne of mill feed for an incremental capital requirement of US$30.3 million for an existing operation.

Jan 1, 1992

By Cotton P. L

Although the terms "pipe" and "tube" are normally considered synonymous, a distinction is often drawn, the former term being applied to the hot finished product and the latter to cold finished material. It is, considered that the title of this paper includes hot finished seamless, and continuous-weld pipe, cold drawn seamless tubing, and electrically welded tubing.The continuous-weld process will be reviewed first, passing to the various methods of seamless manufacturing, which, in addition to meeting the demand for hot finished seamless pipe, also supply the raw material for cold drawn tubing, the manufacture of which will then be described. Finally the electric resistance-weld process will be Considered, and the paper will conclude with a brief review of the processes described and trends in present-day manufacture.CONTINUOUS-WELD PIPEThe raw material for this process is delivered in the form of coiled, hot finished, strip steel, generally referred to as "skelp". The end of one coil is electrically buttwelded to that of'the next, so forming an unbroken strip. This continuous ribbon of 'steel is fed into a skelp heating furnace, and brought to the correct temperature for the forming and welding operations which follow. This temperature is usually about 1,350°C.The heated skelp issues from the furnace into 'a multistand mill, in which the first pair of rolls is designed to form the skelp into tubular shape, the edges being in close proximity to, but not touching each' other. These edges...

Jan 1, 1951

Although developed primarily for sintering tantalum, the unit to be described can be used to heat-treat metals in the form ofa bar, wire or strip, by passing a current through them. The upper temperature limit with this type of heating is the melting point of the metal being heated.The unit was designed for vacuum work, but. various gases can be used if required.Briefly, the vacuum sintering furnace consists of a bell which is counter-balanced and may be lowered onto the brass base plate which holds the electrodes. A rubber ring seal is used for vacuum work. The lower flexible grips are bolted to the brass base plate which is at earth 'potential, while the other electrode passes through the plate by way of an electrically insulated vacuum seal. This upper electrode, the height of which can be altered as desired, the lower grips, and the bell are water cooled. The vacuum line to the pumps and a line to the vacuum gauges also lead from the base plate. The more important sections of the unit are described below.THE BELLThe unit was designed so that the bell could be lifted clear of the base plate and the electrodes, thus facilitating adjustment of the latter and the mounting of the specimen to be heated. A double walled steel bell, 20 in. high, with t in. cavity was used. The bell was fabricated from 10 gauge mild steel sheet using a double overlapping run of arc welding for all seams. A water inlet and outlet...

Jan 1, 1946

By Jefferson CW

Middle-to-Late Proterozoic stratigraphy and metallogeny in the eastern part of the Canadian Cordillera and in South Australia are strikingly similar. In both areas, thick, predominantly shallow-water strata and their contained mineral deposits can be divided into three sequences (A, B, C) that record episodic and prolonged continental rifting. It is proposed that Adelaidean strata of Australia were deposited adjacent to Belt-Purcell, Mackenzie Mountains and Windermere strata of the Canadian Cordillera within an epicontinental trough of a "Hudsonia" regacontinent. With the final rifting of this trough, the paleo-Pacific ocean was born. By Early Cambrian time, Australia- Antarctica was on the trailing "east" side of the nascent megacontinent, Gondwana, and was being modified on the "west" by accretion in the Pan-African event. North America, more or less surrounded by trailing edges at this time, was analogous to the Cenozoic African plate. This hypothesis accommodates the available paleomagnetic and radiometric data. It has implications for pre-Pangean plate tectonics, paleogeography, and the predictive metallogeny of both areas.

Jan 1, 1987

Ore deposit modelling is becoming an increasingly accepted tool in mineral exploration. Successful models have already been proposed for several ore deposits of base metals and gold, but tin has so far received comparatively little attention, perhaps because of an excessive preoccupatioi with alluvial operations. This situation is rapidly changing and some of the world's most profitable and newly commissioned tin mines are large, primary tin deposits. Some basic principles of ore deposit modelling are briefly reviewed and the fallacy of an excessive reliance on grade tonnage diagrams based on the tin industry worldwide is discussed. The four proposed models and submodels of large, hard-rock, tin deposits focus on basic concepts such as the spatial relationship with "tin granites", depth of emplacement and the level of erosion. General concepts are drawn. The modelling of large primary tin deposits is reviewed not only in its geological and exploration aspects but also in its mining and economic implications.

Jan 1, 1986

By McGill RA

The Ranger Uranium Mine is surrounded by a World Heritage National Park. The strict environmental controls under which the mine operates are based on scientific and social requirements. Release of non-process storm runoff water to the Magela Creek during flood discharge and under controlled conditions has been identified as Best Practicable Technology for the operation of the water management system. Social and political factors have limited this release to a wet season with an Annual Exceedance Probability of one in ten. The first-generation trigger mechanism was based on a percentile analysis of monthly rainfall. The second-generation trigger is based on cumulative monthly volume increase in the retention ponds and is considered to be more applicable to the operation of the mine water management system.

Jan 1, 1988

Since the announcement of early experimental work on rotating magnetic field (RMF) separation at the Sixth Mill OperatorsÆ Conference in 1997, the concept of RMF separation has been developed and tested further, and a range of separator designs is now being developed for the mineral processing industry. Shortened, but full diameter, prototypes of these designs are now available for test separations. The main advantage of RMF low and medium intensity attraction separation is the significant reduction in particle entrapment. This reduction is so significant that RMF separators are capable of operating very close to their theoretical limit for separator precision. This makes small laboratory RMF attraction separators ideal for low to medium intensity magnetic sample analysis, and larger separators ideal for applications requiring sharp magnetic susceptibility splits. Feedrates and separation rates are comparable to those of conventional attraction separators. Although RMF attraction separators are now well advanced in development, RMF rotation separation is still in the early experimental stage. The exception to this is the dry particle rotation eddy current separator that offers eddy current separation of small non-ferrous metallic particles from about 2 mm down to about 100 microns. Wet small particle eddy current separation is also possible, but has not yet been developed to a practical stage.

Jan 1, 2000