Search Documents

By M Stephens, T A. Sutra

Currently, there are several open pit mines with production rates of about 200 000 tpd of ore that are reaching the end of their economic lives. In most cases, the remaining orebody extends to depths greater than 300 m below the pit limit, leaving hundreds of millions of tons of reserves that can only be recovered by means of an underground mining method. One such method used for mass production is block caving. This paper presents a ventilation system for a four-zone block cave mine operation developed on a footprint 1000 m wide and 1200 m long. The system is designed for a mine with a nominal production rate of 120 000 tpd of ore using diesel powered units on the production and reduction levels. It discusses the air quantity requirements for the worst case scenario, which is anticipated to occur five years after the mine has reached its full production capacity. Finally, it summarises the results of computer modelling exercises that were carried out to determine an economic ventilation infrastructure that includes shafts, drifts, main fans, and ventilation control devices.

Jan 1, 2005

By B Clements, R Dunne, J Dioses, S Hart

In April 2003 plant upgrades in the æLow GradeÆ Cadia Hill circuit were undertaken in order to improve concentrate quality and metal recoveries from the flotation circuit. The major changes involved: circuit reconfiguration to allow all concentrates to be reground to less than 38 ¦m prior to final cleaning; increasing ball charge in the regrind mill to fully utilise all of the installed power; desliming of the cleaner scavenger concentrate to improve the circuit water balance; and the inclusion of a gravity concentrator in the regrind circuit to recover more free gold to bullion.Once the flotation circuit had stabilised under the new operating conditions concentrate launder modifications and increased froth crowding on the scavenger flotation cells permitted the introduction of stronger collectors without compromising concentrate quality or circuit stability.Twelve months on, the copper concentrate grade has increased by two per cent and metal recoveries increased by three per cent and seven per cent for copper and gold respectively. The project capital outlay of approximately $2.0 million has been repaid in less than three months. This paper will review the project from the design, construction and commissioning perspective as well as the subsequent debottlenecking exercise that was required to eventually yield the full benefits of this upgrade.

Jan 1, 2005

By A Duran

When dealing with rocks in the geotechnical profession, a common activity involves providing an estimate of the intact strength. The tactile approach and descriptions of strength that apply to soils is well documented, can be readily checked through the use of a pocket penetrometer and are known to provide reliable estimates of strength. Moreover, although different soil strength classification systems are present, the bounds between classification classes are compatible across almost all documented classification systems. However, this is not the case for rock strength materials. There are numerous systems within the literature, some with different concepts, and almost all have different bounds to each strength classification. In this paper, the author presents seven classification systems for estimating intact rock strength and highlights issues in their implementation. Example cases are presented to discuss the typical concerns confronting field strength estimates.CITATION:Duran, A, 2014. Comparison of field estimated strengths, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference , pp 101–106 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 5, 2014

While sampling techniques used by the mineral industry continue to improve, sampling is still an area which is often neglected. It is often left to personnel who do not fully appreciate the significance and importance of sampling. Yet sampling and sample processing are of vital importance. There is little point in making major capital investments in the latest analytical equipment and spending considerable time obtaining the best analytical precision, if the sample provided for analysis is seriously biased in the first place.

Jan 1, 1976

Knowledge of the crystal chemistry of carbonate apatites is very important for the development of the concept of biomineralisation and the creation of a scientific base for new biocompatible materials for medical purposes. The present work is devoted to research results on various synthetic and biological carbonate apatites obtained at Saint Petersburg University over many years. All-important problems will be considered such as the location of CO32- ions in the apatite structure, the ionic substitutions in various biological apatites and the development of synthesis methods for their analogues. Syntheses of apatites were realised by precipitation methods and under hydrothermal conditions (from solid compounds and by calcite treatment). Biological samples used in this study were physiogenic and pathogenic apatites formed in the human organism, eg in teeth and in renal and salivary stones and dental calculi as well as apatites from fossils of different taxonomic families (brachiopods, conodonts, fishes, reptiles, mammal) with different geological ages and burial conditions. The study of the crystal chemistry of carbonate apatites has been carried out by powder (including high-temperature measurements) and single-crystal X-ray diffraction methods, IR-spectroscopy, thermal analysis and various chemical analytical techniques.

Jan 1, 2008

By V Gupta, Z Huang, S K. Biswal

G-Cell is a new design modification of the Imhoflot pneumatic flotation technology, which utilises a self-inducing aerator inside a downcomer, where bubble-particle attachment takes place. The present study has investigated the suitability of the G-Cell technology for cleaning fine coal using a 0.8 m diameter prototype unit at a coal preparation plant operating in the Midwestern United States. A slip-stream obtained from the overflow of raw coal cyclones operating in the plant, containing nominally minus 150 micron size particles and having ash content in the range of 40 per cent to 50 per cent and sulfur content in the range of 1.30 per cent to 1.50 per cent, has been used as the feed for the G-Cell. The performance data produced from the G-Cell tests are found to be very close to the ideal performance curves produced from release analysis. A statistically designed experimental program has been conducted to investigate the parametric effects on various key process responses, such as combustible recovery, product ash and sulfur rejection. The empirical models developed in this study have been utilised to identify a suitable experimental region for achieving a desired combination of response targets.

Jan 1, 2005

By R Markoski, P Grealish

The requirement for rapid vertical development for underground ventilation is often a factor when dealing with dynamic mine plans, with short vertical developments being used to optimise ventilation systems. In an effort to increase the safety and efficiency of the constructions, a simple and effective sinking methodology is required that is both adaptable and repeatable. A modified shaft construction methodology is proposed that attempts to minimise risk to the personnel as well as be cost-effective. Readily available equipment is used to ensure adaptability to the various environments and shaft parameters.One of the greatest risks of shaft sinking is having personnel working suspended over open cavities or underneath suspended loads. Removing this risk, by ensuring all construction is done from solid ground, allows for safer sinking operations. As the process is repeatable, familiarity and confidence in its construction sequence will increase with each successive sink.A trial sink is performed with a 3.6 m diameter, 20 m deep shaft. The shaft was excavated using a conventional strip-and-line philosophy, with the shaft then being lined from the collar via the use of large diameter corrugated steel culverts. The annulus between the steel culverts and shaft excavation is then filled with a concrete mixture to secure it in position.The new process was successful, with no personnel at any time during the process being suspended above an open excavation. The installation had relatively low capital and operational costs and was completed faster than an equivalent, conventional concrete-lined shaft construction. Therefore when compared to conventional shaft-sinking methods, this process can be considered safer, more efficient and relatively cost-effective.Further research is required to determine whether this method can be expanded to larger vertical developments.CITATION:Markoski, R and Grealish, P, 2014. A new method for rapid vertical development of underground ventilation shafts, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 603–606 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

Contemporary approaches to safety management appear to be failing short of meeting its mark in improving mine safety. This is evidenced by the high workers compensation, high incidence rates and fatalities. Evidence from high-risk and complex organisations points towards safety culture as being important in improving site safety. In more recent years resilience engineering has been touted as a new and innovative way of managing safety. This paper reviews and synthesises previous literature on safety culture and resilience engineering. It then highlights methods that can be used to measure safety culture and resilience engineering, and explores similarities and differences between complex organisations and gold mining to identify opportunities for more innovative approaches to improving safety in gold mining operations through safety culture and resilience engineering.

Aug 1, 2010

It is a very great pleasure indeed to participate in this interesting and important seminar. My two visits to Australia in the past have been extremely pleasant and this one is equally so. My task is to tell you what has been happening in the United States, in these past few years especially, in regard to the management of our air resources and to present in some detail the difficulties we in the copper, lead and zinc smelting industries have been experiencing. The sudden upsurge in interest in air pollution in the United States is a strange phenomenon indeed - strange because we've had air pollution a long time, just as long as there have been large cities using fossil fuels for heating purposes. And the problem has been studied for quite a long time. As early as 1919 studies by the U. S. Bureau of Mines were done in Salt Lake City, where I .live. In the winter of that year extensive measurements were made of airborne particles - dust and smoke. The average concentration of particles found was 870 micrograms per cubic meter of air. A very large number compared to levels we find today. A microgram of course is a very small unit, one twenty-eight millionth of an ounce. A fine human hair two inches long weighs about 100 Micrograms.

Jan 1, 1971

The homologous series of saturated fatty acids investigated in this study generally show a steady gradation of properties with chain length. The solution pKa values were assumed constant at 4.9, however reported pKa values could be lower or higher. Hematite flotation response and surface pressure for aqueous solutions of these fatty acids were measured as a function of pH. For the shorter chain fatty acids, the undissociated acid was shown to be the predominant surface active species with flotation, supplemented by the physical adsorption of acid anions as the chain length increased. The reduced solubility of the longer fatty acid carbon chains made these reagents ineffective as flotation agents. The maximum flotation response of hematite using tetradecanoic acid corresponded with the precipitation edge of the reagent. The results show that the values of surface pressure of the surfactants are not always a good indication of their effectiveness as flotation collectors.

Jan 1, 2005

By N Currey, G W. Wilson, P Ritchie

Kidston Gold Mine in Queensland, Australia has a 310 ha tailings impoundment that has undergone final closure rehabilitation. Kidston Gold Mine evaluated their closure options for this low acid generating tailings impoundment, and due to a lack of cover soils and the cost of importing material, the mine decided to investigate the possibility of direct vegetation onto the tailings impoundment surface. The mine subsequently embarked upon a well planned and detailed research program to determine the feasibility and sustainability of this closure option. The research program included vegetation trials, toxicology studies for metal uptake by vegetation, as well as a comprehensive closure water balance model for the tailings impoundment complex. This paper describes the results of the long-term closure water balance for the tailings impoundment complex for the pre-closure state of the impoundment, as well as predictions towards the impoundment performance once final rehabilitation of the tailings impoundment complex has been achieved. The water balance presented is unique in that it is founded on unsaturated flow principles and accounts in full the impacts of the surface flux boundary conditions. This novel approach enables the prediction of actual infiltration rates into the tailings impoundment surface, which in turn allows for the calculation of how much seepage will exit from the tailings dam toe drains.

Jan 1, 2003

By Vynne J. F

Drill monitors for rotary blasthole drills have been available to the mining industry since the 1970s. The early monitors were pen strip chart recorders that were developed for the oil drilling industry and adapted to mining. They recorded drilling parameters such as depth, pull-down pressure, torque, RPM, and hailing air pressure. While these recorders could generate a large volume of paper, the amount of useful data was minimal. The data was not summarised and required an engineer to interpret the chart traces. Being a mechanical recorder, the devices were also susceptible to frequent failures. Modem electronics, and the development of the personal computer and its associated software have radically changed the type of instrumentation that is now available for blasthole drills. Perhaps more important is what can be done with the data. The PC allows the logged data to be analysed, summarised, and a variety of reports to be generated. The reports can be customised to meet the specific requirements of the mine and reduce the amount of time that is required to interpret the data. There is also an increased awareness in the mining industry of the importance of production drills. Blasthole drills have typically been the piece of production equipment that received the least amount of attention in a surface mine. Management focussed on the trucks and shovels or draglines. This situation is changing, and therefore the benefits that can be derived from monitoring drill performance are being recognised. Potential economic benefits of installing drill monitors have been documented in previous papers (Peck and Vynne, 1992). Mines are finding that pay-back periods of less than twelve months and rates of return in excess of 30 per cent are not uncommon. These benefits include the following: 1. Reduced overdrilling; 2. Increased rate of penetration; 3. Helping to locate coal seams; 4. Identification of weak and strong zones; 5. Reduce geophysical logging; 6. Optimising blasts; 7. Improved fragmentation and diggability; 8. Decreased coal dilution; 9. Increased bit life; 10. Reduced maintenance costs; 1 I . Improved accuracy of data and reports.

Jan 1, 1995

By D J. Bradshaw, E M. Wightman, B Newcombe

Flash flotation plays an integral role in many of the gold and sulfide mineral concentrators around the world, and yet despite this widespread use, very little information on this unit process is available in the published literature. For operations to maximise the performance of their flash flotation circuits, understanding how these cells operate, the nature of the particles they target and how to predict whether a flash flotation cell should be used on a specific ore type is of vital importance. This paper provides a summary of the key findings of a large flash flotation research project based in the operating environment of a refractory gold concentrator. The influence of key flotation performance criteria including gas dispersion, residence time and particle segregation within the cell will be discussed and recommendations for process improvements will be made throughout. The nature of the particles within the flash cell will be examined, as will the impact on the type of particles that are passed to downstream processes when the flash flotation cell is taken off-line. The development of a laboratory method to determine whether an ore is suitable to undergo the flash flotation process is also presented for its potential to aid in flow sheet development and optimisation for new ores.CITATION:Newcombe, B, Bradshaw, D J and Wightman, E M, 2012. Into the belly of the flash à Insights into the mechanisms at work within a flash flotation cell, in Proceedings 11th AusIMM Mill OperatorsÆ Conference, pp 163-170 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 29, 2012

Structural assemblages of veins, shear zones, and wallrock alteration zones arising from fault-valve action on steep reverse fault systems are reviewed using observations from mesothermal gold-quartz lodes in the Archean Yellowknife, Abitibi, and Yilgarn greenstone belts of Canada and Western Australia, the Cretaceous Mother Lode system in the Foothills Metamorphic Belt of the western Sierra Nevada, California and the Victorian goldfield hosted in a folded quartz-turbidite succession of Paleozoic age in Australia. Despite differences in the host rock assemblages, the deposits have many structural characteristics in common. These form a useful exploration guide when re-evaluating comparable, but poorly described gold-quartz vein systems such as those in the Reefton area of New Zealand.

Jan 1, 1992

By S J Riley

The cover (cap) over the tailings pit at Nabarlek uranium mine must be structurally stable as it will act as a barrier to radon gas emission and have to contain other long-lived radionuclides. Structural stability is primarily an issue of erosional stability in the context of a design life of thousands of years. The primary agent of erosion is fluvial, dominated by rainwash, overland flow, filling and gullying in the local area. Other agents of erosion are of less concern although biogenic agents of erosion (eg termites and windthrow) may enhance fluvial activity. Several methods may be used to assess erosional stability. They fall into two main categories, namely erosion modelling and geomorphic modelling. The former is illustrated by the Universal Soil Loss Equation in which parameters describing aspects of the geotechnical and hydrological properties of the rehabilitated surface are used as input for the modelling of erosion rates. The latter is illustrated by estimates of gully and valley erosion using empirical models. Estimates of the erosion rates and stability of the Nabarlek cover are presented. The two main techniques are complementary and it is argued that rehabilitation design must make use of both approaches when estimating erosion and geomorphic stability. More recent developments in geomorphic modelling using numerical techniques incorporate both approaches.

Jan 1, 1994

By J Rowland

"This paper was primarily put together in order to demonstrate what are believed to be acceptablestandards, in relation to ventilation surveys and the subsequent model assembly process. Thiswas brought about by the fact that in many parts of the world it is regarded as acceptable to carryout ventilation surveys and then build and supply the client with a æstick fi gureÆ type ventilationmodel. Such stick models have arguably litt le use and a very short life span in the real world and isalmost impossible for site staff to maintain. Thankfully most underground coal mines in Australia strive to maintain a true replica model of their ventilation circuits and to keep them in a relatively good state. Given that these mines own and maintain the models, it is often seen as necessary to update or rebuild them. The level of survey detail required to do so is totally dependent on the end use of the data and the criticality of the accuracy of the data set, to the ongoing safety and viability of the business. Mine technical personnel should think clearly about the use and importance of the ventilation survey and subsequent report outputs required that will help them bett er understand their mines and bett er prepare them to manage their ventilation circuits, on an ongoing basis. This paper provides some guidance for Australian ventilation engineers so they may plan and execute this work æin houseÆ, should they rightly choose to do so. To this end, methods of data collection and circuit analysis required for surveys of a high order of accuracy are detailed. Also, some of the issues which are important when formulating a strategy to carry out the appropriate ventilation survey for the required purpose are summarised. As well, the major details that should be furnished within any survey and some survey/report outputs and/or omissions, which are clearly not acceptable, are highlighted."

Jun 1, 2012

By P Donecker

Like all chains, iron ore values chains are only as strong as their weakest link, which in ore processing is often the humble chute. While mechanically the simplest element in the iron ore flow sheet, chutes are often the most problematic and regularly the major cause of unscheduled downtime. Chute designs have remained static for decades, despite the extra demands being placed on them by grade reduction, which impacts chutes in three ways viz: 1. Higher volumetric rates as infeed increases to meet production targets. 2. Higher moisture content as mining goes below water table. 3. Stickier properties as the dilution phase is often clay based. While there is no shortage of ideas and the geometry options are infinite, the fact is that chute design has not kept pace with grade decline and has remained essentially unchanged. One reason cited for this lack of innovation is the difficulty evaluating and de-risking designs. While the power of computers running Discrete Element Method (DEM) models has advanced, the models themselves still need to be ‘calibrated’ with the dynamic properties of the ore. Flow properties commonly measured for bin design are useful for static situations only and were never intended to predict dynamic behaviour as in chutes, a critical qualification lost in the mists of time. So while they always produce a colourful and reassuring animation, DEM models informed by static ore properties often result in wildly inaccurate real world predictions. Responding to this low success rate, many operators are now utilising physical modelling to help reduce risk and avoid the consequences of having an underperforming chute in their value chain. Physical testing, in a dimensionless scale-down of the proposed system (bulk material and chute geometry), addresses the shortcoming of mathematical models designs and when used in combination with DEM is the best option. In the ideal world, the focus of chute modelling should be innovative design concepts aimed at addressing future needs, however in reality the focus is nearly always on modifications to installed chutes that are underperforming even today. This situation can be traced back to design procedures which if informed at all, are based static ore properties. As an industry, we need to break this cycle and become more proactive, which means addressing flaws in the current design process. In 30 years of providing modelling support to the industry, I have looking at hundreds of underperforming chutes in the iron ore industry. This practical experience has led to a unique and unbiased perspective on chute design and their performance in the real world. The knowledge presented in this paper can not only be used to help avoid baked-in problems now, but also help guide and evaluate designs so we can deal with the challenges of our low-grade future.

Sep 18, 2023

By R Minnitt

Two methods of calibrating the parameters K and Alpha for use in Gy’s formula for the fundamental sampling error were investigated. Approximately 480 kg of broken ore from Harmony’s Target gold mine in South Africa was used to compile the replicate samples for two experiments. The duplicate series analysis (DSA) and segregation free analysis (SFA) methods differ in terms of their approach to recovering the sized materials required for the calibration procedure. In this experiment the DSA method split off six more-or-less equal masses of material from a 75 kg lot that was successively crushed to finer and finer fragment sizes. The sublots so formed were split into 32 samples and fire assayed for gold. The SFA method used approximately 250 kg of broken ore crushed to 95 per cent passing 2.50 cm, which was then passed through successively finer screens until a sublot of less than 0.0075 cm was obtained. Each of the 15 sublots obtained in this way were split using a riffle splitter into 32 samples that were fire assayed. A total of 672 fire assays were used in these experiments. The sampling parameters K and Alpha were used for the compilation of a nomogram and to calculate the gold liberation size of the ores. While there are no definitive results in terms of the actual gold grain sizes against which the calculated sizes can be compared, it appears that the DSA method produces more acceptable results.CITATION:Minnitt, R, 2014. A comparison of two methods for calculating the constants K and alpha in a broken ore, in Proceedings Sampling 2014 , pp 165–178 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 29, 2014

By J Hadjigeorgiou

Underground mines often rely on ore pass systems to ensure the transport of ore and waste. Consequently, it is important to ensure the smooth operation of such systems. Ore pass degradation that may require rehabilitation results in production delays and high operational costs. The occurrence of hang-ups within an ore pass also leads to disruption of ore production. There are important safety concerns when worker intervention is necessary to re-establish material flow in the ore pass. In order to facilitate the design of ore pass systems, mining operations often rely on past experience, or semi empirical guidelines. This paper describes recent efforts to establish a comprehensive database on current practices; encountered operational problems and solutions in ore pass design in Quebec underground mines.

Jan 1, 2003

"Geometallurgy is a discipline that seeks to improve the sustainability of the extraction of metals and minerals by promoting the smarter use of non-renewable resources, better energy efficiency and greater use of renewable energy. To achieve these goals, development of innovative technologies and approaches are being developed along the entire commodity value chain, starting with exploration and extraction and extending to reuse and recycling. This paper discusses the geometallurgy of industrial minerals with special emphasis on kaolin, a versatile industrial mineral applied in ceramics, paper, paint, plastics, rubber, pharmaceuticals, cosmetics, ink, sealants, adhesives, sanitary ware, glass fibre, toothpaste, animal feed etc. Aspects of kaolin extraction in south-west UK are analysed from a geometallurgical perspective. While geometallurgy already features in kaolin extraction, its role can be significantly expanded by combining advanced in-pit characterisation and orebody modelling with integrated planning and control of the refining and calcination process. This paper highlights the importance of innovation in realising the full potential of geometallurgy.CITATION:Glass, H J, 2016. Geometallurgy – Driving Innovation in the Mining Value Chain, in Proceedings The Third AusIMM International Geometallurgy Conference (GeoMet) 2016, pp 21–28 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jun 15, 2016