Search Documents

By S N. Donaldson, B L. Hollis, K Wynn, L Potts, M Evans

A real-time load-haul-dump (LHD) dispatch optimisation tool has been deployed at Panel Cave 1 and Panel Cave 2 at Newcrest’s Cadia Valley Operations. The tool, known as ORB, is the first known successful implementation of an optimisation-based, autonomous, real-time dispatch tool, custombuilt for underground mining operations. ORB can co-ordinate the optimal dispatch of LHD’s in a block cave to achieve a range of objectives while adhering to draw compliance and geotechnical constraints. It is an example of highly automated short-term interval control. This paper starts by outlining the pre-existing business planning process, detailing the simple logic that produced the daily draw order. Next, the motivations for a real-time dispatch tool are presented, drawing comparison to the limitations in existing planning processes and how these can be overcome through an optimisation-based, autonomous, real-time dispatch tool. Subsequently, the paper details the Ratio Bogging Draw Strategy, through which tonnes targets are expressed continuously on draw bells or draw points as a ratio of total cumulative cave draw. This signifies artificial planning boundaries are removed and that draw targets are linked within a cave; such that tonnes are unlocked by bogging other parts of the cave, instead of as a function of time. This creates incentive within the target mechanism for fixing and bogging struggling draw areas whilst allowing uncapped progress if all draw targets are progressing within compliance. Furthermore, the optimisation tool developed is outlined, including the data it uses and the objectives it optimises. Finally, detail on the improvements to operations the implementation of this tool has brought, and the business process change it has facilitated are presented using Newcrest’s Cadia Valley Operations as a case study.

Mar 15, 2021

By Tyler DB, Thin LGT

Coal mass strength properties must be estimated to obtain realistic estimates of coal pillar strength. The limitations of existing techniques for approximating these properties are discussed. The coal mass is anisotropic. The Hoek and Brown approach to rock mass property estimation is modified to allow for this. This approach requires the Rock Mass Rating (RMR) for the strata. In the normal case where bedding is sub-horizontal, these major planes of weakness have little effect on the strength of pillars. As a result of this the RMR must be measured parallel to bedding. This means that a significantly higher rating than that usually obtained for coal is observed. The use of mass strength property estimates in extant empirical relationships is outlined. At high width to height ratios, an acceleration in the rate of increase in pillar strength with increasing width to height ratio has been observed. The empirical relationship developed by Salamon (the so called squat pillar formula) takes account of this. This relationship was found to have significant limitations with respect to its universal application. Modifications are made to Bieniawski's empirical formula to extend its use to large width to height ratio (squat) pillars. This new squat pillar formula has none of the disadvantages associated with Salamon's relationship. Strain softening was incorporated into non-linear finite difference numerical modelling to estimate pillar strengths. The technique outlined above is used to obtain peak coal mass properties. Modelled pillar strength was found to be sensitive to both peak and post peak mass strength properties. Post peak properties were found to be difficult to obtain and required some back analysis. Modelling results were used to estimate both the strength of squat pillars and parameters for use in a new squat pillar empirical strength relationship.

Jan 1, 1992

The introduction of large diameter holes to underground mining has provided the first opportunity to apply near spherical charges in production scale blasts instead of the convent- ional long cylindrical charges generally used in stope and pillar mining. A modified version of the cratering prin- ciple was applied in the blast design in extrac- ting ore across a horizontal area of a stope or pillar. The new rock breaking technique has developed into the Vertical Crater Retreat (VCR) mining system and eliminated raise boring, slot cutting and dilution of the ore by back- fill material. Furthermore it has reduced labour and time requirements thus becoming not only a low cost method of mining but the safest method of underground mining known today. Exceptionally fine muck is provided with a minimum of damage by blasts to walls and re- treating backs of the stope or pillar. The VCR method can also be used for drop- raising, and for the excavation of underground cavities for almost any purpose . The proper explanation of the breakage mechanism of the near spherical charges opposite to the cylindrical charges yet to be found. The mining industry has quickly recognis- ed the value of the VCR mining method which is being adopted by an increasing number of mines

Jan 1, 1978

By M G. Wansbone, R Bhargava

The inferred ground conditions for the proposed mined cross passages at the northern end of the Waterview Connection tunnels consist of an overburden of alluvial and residual soils, with mixed face geology of highly weathered to unweathered extremely weak rock. This paper describes three-dimensional (3D) finite difference analyses undertaken to evaluate the stability of the cross passage headings and to validate the proposed sequence of excavation. The analyses undertaken incorporated the influence of the construction of the mainline tunnels and the breakout opening in the segmental lining for construction of cross passages.The stability analyses were carried out using FLAC3D™, version 4.0 (by Itasca Consulting Group) by progressive reduction of shear strength parameters to obtain a failure condition and estimate a factor of safety. For each step of strength reduction, corresponding increments of displacements of several points on heading faces were monitored. The stability obtained from numerical analyses was compared with analytical solutions. Interpretation of results of drained analyses indicated instability of the upper 2 m of heading face within the highly weathered rock mass. Additional analyses were undertaken by including grouted fibreglass dowels to reinforce the heading face. The results of the additional analyses showed significant reduction in displacements and yielding of ground around the face. The proposed temporary support comprised face reinforcement using grouted fibreglass dowels in conjunction with canopy tubes and perimeter support of steel fibre reinforced shotcrete. The stability of the construction sequence, which was related to the specific requirement of the proposed excavation equipment, was validated.CITATION:Wansbone, M G and Bhargava, R, 2014. Analysis of stability and design of face support for cross passages – Waterview Connection tunnels, Auckland, New?Zealand, in Proceedings 15th Australasian Tunnelling Conference 2014, pp 339–344 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By Singh BN, Chakravarty PK, Chatterjee LM

Indian blast furnaces operate with coke gener- ally containing 24 to 28% ash compared to 10-15% ash in coke in most other parts of the world. The operating problems are further aggravated by the high alumina content and the adverse alumina to silica ratio in the ore. The above factors not only increase the coke rate but, at the same time, increase the flush slag volume, make the bosh slag highly limey and thereby viscous, and produce a flush slag containing 24 to 26% alumina. Relative- ly low flame temperatures (RAFT) make conditions more difficult. The high basicity of the bosh slag limits the maximum flush slag basicity to around 1.0, beyond which the burden movement is adversely affected by the viscosity of the bosh slag: This effect is partly controlled by operating blast furnaces with high MgO in the flush slag (around.10%), which also improves the desulphurizing power of slag. Steps are underway in some plants to inject lime through theòtuyeres to control the bosh slag basicity and also to neutralise the large quantity of silica which is released at the tuyere level from the coke ash, so that the silicon content of the hot metal can also be controlled. High bosh slag basicity coupled with the characteristics of iron ore/aggolmerates, widens the softening-melting zone and alters the shape of the softening-melting zone. This leads to operat- ing difficulties and poor hot metal quality. This paper discusses the above aspects of Indian blast furnace operation and steps being taken to surmount some of the above difficulties.

Jan 1, 1981

By Wang SS, Frattaroll DR

In the development of novel sulfide collectors, especially for the low-lime and acid circuits, flotation of chalcopyrite, chalcocite, covellite and pyrite was studied with both new and commercially available S- containing collectors. The natural float- ability of sulfides, water quality, and redox potentials - all of which were considered im- portant in assessing collector strength and selectivity - were also investigated. Chalcopyrite exhibited the highest natural floatability. The response to most collectors, however, was chalcocite > covellite > chalcopyrite > pyrite. Water quality had a very significant effect on both natural and collector-aided floatability. De- ionized water and tap water had a flotation suppression effect compared with doubly- distilled water. Flotation results with single minerals are correlated with those for copper and pyrite from natural ores. Several novel collectors have now been developed for sulfide flotation in acid, neutral or mildly alkaline circuits. The results for four of these collectors, which have shown promise in commercial applications, are discussed in this paper.

Jan 1, 1986

The scheme of rehabilitation of surface plant commenced in 1936, included the provision of improved and more hygienic changing and bathing facilities for the employees.At that time the Thompson's Shaft section of the British Mine was being prepared for a resumption of operations, and it was decided to repair and re-equip the existing building. Thus any new scheme adopted could be given a thorough trial, and the proved arrangement used as a basis for the contemplated new main changehouse on the North Section.Investigations were carried out to determine the most suitable arrangement for the Thompson's Shaft changehouse, to provide for a total of 120 men, with particular regard to the internal fittings and fixtures. Also, as the mining conditions were such that a large proportion of clothes worn underground by miners, etc., were wet by the end of the shift, the problem of drying these clothes in the availaole time from a man coming off shift to his commencing again some sixteen hours later was one of the most important to be dealt with.The changehouses in use on the North mine section of the lease were provided with racks around the walls for the men to hang their street clothes on, and a section was partitioned off to house the mine clothes and their drying facilities. The actual drying was carried out by means of hanging the wet clothes over racks between which ran pipe coils heated by means of hot water circulated from the hot water boiler supplying the showers.This method had proved to be far from satisfactory for several reasons, the main objections being:-

Jan 1, 1940

With increasing depth of mining, geotech nical factors assume increasing importance in the design and operation of open pit coal mines. Dragline strip mines are particularly sensitive to stability conditions since the draoline is a relatively inflexible machine, particularly in relation to its limited dump- ing radius for overburden disposal. Geotechnical factors relevant to strip mine design include: 1. spoil pile stability 2. wall stability 3. floor stability 4. excavation characteristics 5. groundwater conditions A basic geotechnical investigation pro- gram for new mine feasibility studies is described. This includes: 1. terrain evaluation 2. geotechnical drilling and logging 3. geophysical logging 4. materials testing 5. seismic refraction traversing 6. groundwater studies Such a program will give an overall geotech- nical assessment of the site and highlight any areas which may require further, more detailed Investigations

Jan 1, 1981

By O. J. RICHARDS

The Wongawilli system of mining has been in use for over 30 years and has enabled high production rates and acceptable extraction ratios to be achieved in seams less than 4 m in thickness. A modification of the Wongawilli system has been developed to permit the use of a continuous miner and mobile equipment to extract a coal seam 6 m thick. Following physical and mathematical model studies the new mining method is now undergoing field trials at Collinsville, Queensland. Progress of the field trials to date has achieved 99% extraction of the upper slice by remote control operation of the continuous miner and established the feasibility of installing resin grouted wooden dowels in the coal floor to reinforce the coal septum. The method is explained in the text.

Jan 1, 1980

By Hustwick I

New Zealand Steel Mining Limited operates two independent sand mining operations on the West Coast of the North Island of New Zealand. (Fig. 1)Waikato North Head 30km south of Auckland supplies ironsand concentrate as the raw feed for New Zealand Steel's works at Glenbrook, and Taharoa 70km further south, exports ironsand concentrate to Japan. Taharoa uses two sets of six low pressure Warman centrifugal pumps in series to load bulk ore carriers 3km off shore through two underwater pipelines.Waikato North Head delivers the ironsand to Glenbrook l8kms through a 200mm ID buried pipeline using two stages of high pressure positive displacement (HPPD) pumping.A high level of operating and maintenance expertise has been developed since commissioning the two systems which are proving to be reliable, efficient and of minimal impact environmentally.

Jan 1, 1990

By Drain P, Dibdin T. R

THE completion of the Linda incline man and supply haft at the Mount Morgan Gold Mining Oompany's mine led to an investigation of the various safety gears in general use in mining shafts. One of these gears completely fulfilled the necessaryconditions. This paper endeavours to give a description of the man car and safety gears now operating in the before mentioned shaft, together with the main considerations leading to their design and sub equent adoption. Fig 1 diagramatically shows a longitudinal section of this shaft.

Jan 1, 1911

Following the Moura No 2 Wardens Court of Inquiry and subsequent changes to the Queensland Mining Legislation there is a requirement in Queensland coal mines for: a person with the recognised competencies to be appointed at each underground coal mine to the position Ventilation Officer; and the person is directly responsible for the implementation of the mine ventilation system and for the establishment of effective standards of ventilation for the mine. The Regulations require that an underground mine must have principal hazard management plans that provide for at the least the following: emergency response, gas management, methane drainage, mine ventilation, spontaneous combustion, and strata control. Other than strata control all the plans require the ventilation officer to have roles and responsibilities to develop, control, monitor and undertake actions in relation to these plans.There are also another 34 Regulations that either directly or indirectly requires the Ventilation Officer to take actions.The purpose of this paper is to outline the information that the regulators look for in sealing plans and the actions the regulators will take if the sealing does not go to plan (TARPs being exceeded).

Jan 1, 2005

By Seneviratne SP

The excessive displacement of the seam floor in headings (i.e. roadways) called 'floor-heave' is often experienced in the underground mines of the Southern Coalfield of New South Wales. Apart from interfering with the mining operations, the phenomenon could be detrimental to the stability of the pillars left for support leading to an unpredictable increase in the subsidence of the overlying strata. The latter could pose a serious problem, particularly in the design of partial extraction layouts of mining for areas where subsidence is to be controlled. The susceptibility of the floor of different rock materials and thicknesses in a given `panel and pillar' partial extraction geometry was examined by two- dimensional Finite Element Modelling of the displacements, stresses and failure zones around the excavations. The modelling, assuming elastic behaviour of the materials, indicated that the maximum vertical displacements of the floor increased substantially as the Young's Modulus of the material decreased to less than 7GPa and the thickness of the layer increased. The results also discount the possibility of a properly designed panel and pillar geometry in the Southern Coalfield of New South Wales being unable to adequately control surface subsidence through the pillar, or its core independently of the yielded ribs, penetrating the floor.

Jan 1, 1992

By K M. P Singh, K M. K Sinha, G S. Jha, T Gouricharan, K K. Sharma

The majority of the powerplants in India are fed with non-coking coals, with the coals dispatched from their respective mines via wagons loaded by a rapid loading system or pay loader. The usual top size of coal is 200 mm and sampling is carried out manually from wagons. The manual method of wagon top sampling of large size raw coal is not only difficult, but also violates some of the fundamental principles of sampling. As per sampling requirements, samples are to be drawn from the full depth of the wagons, which is impossible to be done manually. Since the ash distribution in the different size fractions is not homogeneous, the results from the samples, which do not reflect the true size distribution of the lot, are likely to be biased. More importantly, sample collection by shovel from the top is a function of human discretion and not governed by the equiprobability rule. In another case, the sample has been collected by a cross belt-type auto mechanical sampler for 200 mm size coal at one of the super thermal power stations. Test analysis shows that coal collected using a cross belt-type mechanical sampler also has significant deviations from stopped belt coal samples of 200 mm size due to size segregation. Studies carried out on wagon top sampling through specially designed experiments reveal some interesting features. The presence of bias in wagon top sampling is apparent when compared with the ‘stopped belt’ sample. In this paper, a comparative study between manual wagon top sampling/auto mechanical sampling with respect to stopped belt sampling has been conducted for coal of size 200 mm. In addition, precision studies have been performed for wagon top sampling/mechanical sampling for Indian thermal powerplants.CITATION:Sinha, K M K, Sharma, K K, Jha, G S, Singh, K M P and Gouricharan, T, 2014. A comparative study of manual wagon top sampling and auto mechanical sampling of 200 mm size coal with respect to stopped belt sampling of thermal coal at Indian super thermal powerplants, in Proceedings Sampling 2014 , pp 43–48 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 29, 2014

By Kubo H, Ninomiya R, Ojiro T, Sato T

New high-strength Zn alloys for moulds are demanded from the automobile and electric industries in Japan, because the s rength of Zn moulds is still not high enough for the mass production. There are two approaches to improve the strength of Zn alloys. One is to increase the Al content. ZA alloys (ZA-8, ZA-12, ZA-27) were developed through this approach. The other is to increase the Cu content. But it is known that an increase in Cu generally depresses the castability of Zn alloys, so that the alloys with increased Cu have been rarely studied until now. In this study a reconciliation between the strengthening and the castability of Zn alloys by enriching both with Al and Cu has been attempted. Accordingly we have studied on the Zn alloys containing 4 to 25 mass per cent Al and to 24 mass per cent Cu have been studied. Their fluidity, which primarily corresponds to the castability of the alloy, were measured first and 19 alloys were selected based upon their fluidities and casting temperatures. Mainly the mechanical properties of all 19 alloys were tested and some were found to be excellent in both strength and castability. Z1009 (Zn-IOAI-9Cu-0.02Mg alloy) cast in a sand mould has the tensile strength of 360 MPa while ZAS (Zn-4AI-3Cu-0.04Mg alloy), which is the most popular alloy for moulds, is 215 MPa. Z2520 (Zn-25AI-20Cu-0.02Mg alloy) cast in a sand mould has a Vickers hardness of 178, compared to 107 for ZAS and 104 for ZA-27 (Zn-27AI-2Cu-0.02Mg). Furthermore the castability of Z1009 is as good as that of ZAS. The underside shrinkage occuring in casting ZA-27 is restrained in Z2520.

Jan 1, 1993

Ore sorting is a high capacity, low cost method of preconcentrating ores and in some cases of producing a marketable concentrate. In most cases it is applied to run of mine material, immediately after primary crushing and screening in sizes ranging from 10 mm to 150 mm. Recent developments in bulk sorting of friable uranium deposits have resulted in machines capable of handling fine materials with sensing and separation being achieved on a zone by zone basis. Modern ore sorting machines rely on the synchronous operation of four internal sub systems, feed presentation, sensing, data processing and separation. A variety of different sub systems is available which can be combined in various forms to produce sorters capable of handling a wide variety of mineral types. The benefits in using ore sorting cover a wide range of situations and are applicable to both established mines as well as new mining ventures. Reduced operating costs, increased productivity, capital savings, energy and resource conservation and environmental issues are all part of the reason why ore sorting is finding rapid acceptance in today's mining industry.

Jan 1, 1980

By H Dehghan Jan Abadi, K Shahriar

The iron ore district of Gol-e-Gohar (GEG) is located 60 km south-west of the city of Sirjan, in the Kerman Province of the Islamic Republic of Iran. Six exploration targets have been identified and iron ore has been mined from one area with dry and wet concentrate products sold. Prior to mining commencing in 1999, the proven reserves were estimated at 265 million tonnes (Mt) in 2004 and 40 Mt of 100 Mt overburden has since been mined. Of the six exploration targets, the largest anomaly in the GEG district is Deposit No 3. This paper discusses economic considerations focusing on mine extraction and construction of a concentration and pelletising plant to process ore from Deposit No 3 of GEG. Planned capacity of 10 Mt product (concentrate and pellet) per year is targeted to commence in 2011, and nominal capacity by 2014. The economical evaluation and analysis is one of the most important stages in the feasibility study of mine development. Financial calculations including the provision of financial resources, operation period revenue, loss and profit statement, cash flow, net cash flow, internal rate of return and net present value have been undertaken as part of the feasibility study. The feasibility study operating plan assumes a large open pit mine containing proven reserves of approximately 250 Mt. The feasibility study assumed an economic return of $80 per tonne iron pellet. The economic study determined that Deposit No 3 of GEG can be economically developed by open pit mining followed by magnetite separation and flotation to generate iron concentrate and pellets.

Jan 1, 2007

Coal slurry pumping was introduced into the U.K. in 1973. Gateside packs were prepared in areas of containment using R.O.M. coal and a special fast setting cement. The packs restricted roadway convergence and moderated spontaneous combustion risks, but costs were high and alternptives were sought. A similar system using OPC and an accelerator had limited success. Much more successful was the Aquapack process which used dilute slurries of a special OPC based cement and an accelerator based on sodium carbonate and bentonite pumped simultaneously into la fabric packbag. The Tekpak system using HAC and a much modified calcium sulphate mixture superceded Aquapack on the grounds of improved cement pumping life lower alkalinity and lower costs. A further modification of this system gave a cement with a 24 hour pumping life thus obviating flushing out pipe ranges except at the week-ends, improved packbags also increased the efficiency of the process. The hazard of spontaneous combustion can be inhibited if air supply channels across the waste can be located and plugged. Using gas samples from pack pipes to locate the heating and injecting a special grout, formulated from bentonite, sodium silicate and thixotroping agents. into the waste on the intake road has proved a successful method of controlling heatings. Mine' roadway and face cavities are being safely and successfully filled with cementitious foams produced in a novel placer machine. The foams are based on fast setting cements with specialised foaming agents. Up to 13 cu. metres per hour of fast setting thixotropic foams can be produced and their use is now widespread throughout U.K. coal mines.

Jan 1, 1986

By B Jones, M Chappell

Installing ground support correctly is not an easy task, whether lack of operator training, poor ground conditions or underperforming equipment. Confirming the quality of installation can help with planning and remedial works and help to maintain a safe working environment. A 2?m bolt with 700?mm of encapsulation will pass a 10?t pull test (assuming ground conditions permit); however, it will not provide any data of the unencapsulated length and thus the ability to withstand corrosion. Complimentary testing in the form of non-destructive testing (NDT) can provide factual data that leads to the assessment of the quality of the encapsulation. By improving the quality of the encapsulation, the risk of corrosion is reduced, the ground support durability is improved and hence the asset life is enhanced.This paper presents a case study of a trial using the NDT system RokTel™. Installations of varying quality were installed and tested. The characteristics tested were corrosion, load and free length. These characteristics can be tested and assessed for cable bolts, thread bar bolts and split sets. The aim of this paper is to present NDT testing as a viable method for assessing installation quality and ongoing performance of the ground support.CITATION:Jones, B and Chappell, M, 2014. A non-destructive testing method for measuring bolt condition, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference , pp 307–314 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 5, 2014

By M I. Pownceby, N A. S Webster, A J. Studer, I C. Madsen, J A. Kimpton, M J. Fisher-White, L Lu

In situ synchrotron X-ray and in situ neutron diffraction-based experimentation have been implemented to characterise the formation of the complex calcium ferrite iron ore sinter bonding phases silico-ferrite of calcium and aluminium (SFCA) and SFCA-I. Experiments were carried out using fine-grained (<20 ¦m) sinter mixtures containing ~77 wt per cent Fe2O3, 14 wt per cent CaO, 3.5 wt per cent SiO2 and 5 wt per cent Al2O3, with diffraction data collected during heating until 1300 - 1350¦C, which was enough to ensure complete melting of the SFCA phases. In the case of the in situ synchrotron experimentation, results showed that altering the nature of the starting sinter mixture (ie substitution of goethite for hematite; substitution of an amorphous Al2O3-based mineral for gibbsite) did not have a significant effect on the thermal stability range of the SFCA phases. It did, however, have a profound effect on the formation and rate of consumption of the calcium-rich ferrite phases C2F and CF, and on the formation mechanisms of SFCA and SFCA-I. The in situ neutron diffraction experimentation is the first described in the context of iron ore sintering, and the observation of both SFCA-I and SFCA formation in the in situ diffraction data represents the first step in achieving the goal of charactering iron ore sinter phase formation in large volumes of industrial sinter starting materials with a wide range of particle sizes (up to 6.3 mm).CITATION:Webster, N A S, Pownceby, M I, Madsen, I C, Studer, A J, Lu, L, Manuel, J R, Kimpton, J A and Fisher-White, M J, 2013. In situ x-ray and neutron diffraction studies of silico-ferrite of calcium and aluminium iron ore sinter phase formation, in Proceedings Iron Ore 2013 , pp 487-494 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013