Search Documents

By AIME AIME

THE Wednesday morning session was devoted entirely to the consideration of the tentative code for coal mine ventilation. A. W. Hesse is chairman of this subcommittee. E. A. Holbrook presided at the session and assisted by A. W. Hesse and George S. Rice, gave the historical background of the movement for a ventilation code. They stressed the point that this was to be an engineer's code, and that it was hoped that it might serve as a valuable guide to operating companies in securing greater efficiency as well as safety in ventilation. The discussion was continued into the afternoon session, and by adjournment the entire' code had been covered.' Many sections were referred back to the Committee for further study and several new sections were suggested. The various opinions and new ideas brought out during the discussion proved very valuable and. contributed much to the progress being made in the preparation of this code.

Jan 1, 1929

By R. L. Fleischer, W. F. Hosford

Tensile data for coarse grained aluminum Polycrystals suggest that the "grain size" effect is not due to dislocations piled up at grain boundaries but rather is primarily a relative size effect due to surface crystals being weaker and less confined. STUDIES directed at interpreting hardening of poly-crystalline metals normally identify their strain hardening properties with those in some particular type of single crystal.1"4 The recent recognition in face centered-cubic metals of a nearly linear stage with rapid hardening occuring at comparable rates for both polycrystals and single crystals, suggested that the same process or processes determine both cases and hence that there exists some justification for the use of single crystals to understand polycrystals. Further evidence for the above view may be found by an approach initiated by Chalmers:5 By using bicrystals of controlled orientation it is possible to begin to assemble a polycrystal and also to study grain boundary effects in detail. In this way it has been found that a single grain boundary affects easy glide but not the subsequent stage II hardening.6 This result suggests that a sensitive way to observe grain boundary effects in polycrystals would be to vary grain size and measure easy glide. As will be seen, easy glide is only possible for coarse-grained samples, and hence the results will serve to fill in the gap in measurements between single crystals and bicrystals on one hand and fine-grained polycrystals on the other. One problem inherent in comparing single crystals with polycrystals is the uncertainty as to what slip systems are acting in a polycrystal. To compare the two types of samples, rates of shear hardeninn---L. on the acting -planes are needed. and these may be computed only if it is known what particular systems are active. The acting systems were examined for a coarse-grained polycrystal and it will be shown that the systems supplying the preponderance of slip can be determined with little ambiguity. EXPERIMENTAL PROCEDURE Twelve samples of aluminum were prepared by chill casting into a heated graphite mold, followed by annealing at 635° ± 5°C for 24 hr with an 8-hr fur- nace cool, and finally either etching7 or electropol-ishing.' The samples, with a 7 to 10 cm length between grips and 4.4 by 6.6 mm in cross section, were deformed at a strain rate of about 3 10 -3 . per min in a tensile device which has been described elsewhere.5 The composition was reported by Alcoa as 99.992 pct Al, 0.004 pct Zn, 0.002 pct Cu, 0.001 pct Fe, and 0.001 pct Si; nine samples were deformed while immersed in liquid helium and three in air at room temperature. The stress-strain curve for one of the samples (P-1) deformed at 4.2 "K has been reported previ~usl~.~ This sample was selected for determination of active slip systems. Eighteen of the crystals were examined by optical microscopy to determine the angles of slip line traces and by X-ray back reflection to determine orientation. By this means the slip planes were determined and the resolved shear stress factors for possible slip systems could be computed. Finally each sample was sectioned so that after etching, the number of crystals could be counted for each of ten newly exposed surfaces. The average of these ten values will be termed n, the number of crystals per cross section. Values of 11, varied from 1.9 (nearly bamboo structure) to 12.7. Sketches of typical cross sections appear in Fig. 1. RESULTS AND DISCUSSION: SLIP SYSTEMS 1) Determination of Acting Slip Planes—The stress axis orientation and operative slip planes in eighteen crystals of sample P-1, as determined by slip line traces and crystal orientation, are summarized in Fig. 2. For one of the crystals two planes had a common trace. so that the traces alone did not distinguish which plane or planes were slipping. However it was found that the stress resolving factor for the primary system was 0.386, .while that for the most stressed system in the other plane (indicated bv the dotted arrow) is 0.138. It will be assumed tgerefore that only the primary plane acted. Since the orientations were determined after extending the samples 4 pct, the stress axes may be rotated from their original value by as much as 2 deg in some cases. It is interesting to note that in five crystals only one slip plane acted, in eight two acted, and in five three planes were observed—an average of two slip

Jan 1, 1962

By Ernest Burchard

FLUORSPAR is found in most of the states from the Rocky Mountains westward, and commercial production of the mineral has been reported from Arizona, Colorado, Nevada, New Mexico, Utah and Washington. The map in Fig. 1 indicates the general distribution of many of these deposits but it is by no means complete. In the summer of 1926 the writer examined certain deposits of fluor-spar in Arizona, California, Colorado, New Mexico and Washington; in November, 1927, revisited the Jamestown, Colo., district, and in earlier years examined deposits in Colorado and New Mexico. Based on notes of his own and. on descriptions and other data by H. A. Aurand, H. W. Davis, R. B. Ladoo, V. C. Heikes, W. D. Johnston, Jr., and by producers of fluorspar, he prepared the following brief descriptions of deposits and estimates of reserves of fluorspar, originally for the use of the subcommittee on fluorspar of the Joint Committee on Foreign and Domestic Mining Policy and on Industrial Preparedness respectively of the Mining and Metallurgical Society of America and the American Institute of Mining and Metallurgical Engineers. Descriptions of many fluorspar deposits in various western states and districts have been published. It is not feasible to summarize this literature here, but the appended bibliography will indicate to the interested reader what papers are available.

Jan 1, 1933

NEW MEMBERS The following list comprises the names of those persons who became members during the period Apr. 10, 1916 to May 10, 1916. ALLEN, WILLIAM R.... Pres., Boston and Montana Development Co., Butte, Mont. BARKER, EDGAR EARL, Min. Engr. Mine Supt., Chile Exploration Co., Chuquicamata, Chile, S. Amer. BAYLESS, JOHN Z., Met. Engr Alaska Gastineau Min. Co., Thane, Alaska. BLACKWOOD, ARTHUR E., Mgr., Sullivan Machinery Co., 30 Church St., New York, N. Y. BREYER, FRANK G., Chief Testing Dept., The New Jersey Zinc Co., (of Pa.), Palmerton Pa. CARPENTER, JAY A., Mill Supt... . West End Cons. Mining Co., Tonopah, Nev. CORLESS, GEORGE BRADFORD, Geol., Missouri Bureau of Geology and Mines, Joplin, Mo.

Jan 6, 1916

By J. Cervik, P. C. Thakur, S. D. Lauer

Methane drainage by cross-measure boreholes on retreat longwall faces can be a viable alternative to the vertical gob degas boreholes under favorable circumstances. The research was done in a mine working Pittsburgh coal seam in northern West Virginia under USBM Cooperative Agreement No. 14-09-0050-3252. The study was the first application of this technique to Pittsburgh coal seam. A total of 14 small diameter, inclined boreholes were drilled over a retreat longwall panel from gate roads, to intersect the overlying coal seams. All boreholes were manifolded to a pipeline and the gob gas was extracted by a surface exhaust fan. The methane capture ratio was poor at 7% to 18% at various stages of the longwall panel. A vertical gob degas borehole captured an additional 20% gas. Poor results were due to premature failures of the cross-measure boreholes leading to air leakage. For better performance, the boreholes should be drilled from a point 30 to 45 m (98 to 148 ft) from longwall pillar over the largest chain pillar. The standpipe should be grouted for at least 6 m (20 ft), and the entry containing boreholes and the pipeline must be supported to ensure access for maintenance and optimization of methane capture. Coursing the ventilation air around longwall such that it forces methane migration toward cross-measure boreholes can further improve methane capture. The optimum vertical inclination is 45º ± 10º.

Jan 1, 1986

By P. R. Sperry, M. L. Holzworth, P. A. Beck

The basic work of Z. Jeffries 1,2,3 has long ago established the main features of grain growth in the presence of a dispersed second phase. Working with sintered specimens of initially fine grained tungsten, to which various amounts of thoria had been added, Jeffries found that grain growth was inhibited, that is, practically prevented, up to a certain annealing temperature. When this temperature, which increased with the thoria content, was exceeded, extremely large grains developed abruptly from the fine grained matrix. such a a temperature" was later found by Gross-mann~3,14 in certain types of steel, while ~~i~ showed15 that in other steels grain growth was gradual, without inhibition and abrupt coarsening. Later work demonstrated the connection between coarsening and aluminum additions. The viewpoint that the direct cause of inhibition and coarsening in aluminum killed steels is a fine dispersion of aluminum oxide21 appears to be held quite generally, although some doubts have been voiced even very recently, 20 In steels with Ti additions the titanium carbide phase is considered responsible for the inhibition effects found.20 The coarsening temperature increases with the titanium content. That coarsening may occur, as a result of, certain heat treatments, even in low carboil rimmed sheet steel, was shown by Samuels. He also detected coarsening in a steel ingot of similar composition, after giving it the same heat treatment as that used by him for the sheet material. In this instance the identity of the inhibiting phase has not been determined. However, Tangerding found23 that even the few small carbide particles, which occur in carbonyl iron, have a very marked inhibitive effect. As a result of an oxidizing anneal at 850°C, large grains begin to form at the surface of the carbonyl iron specimen, and gradually grow inward as the subsurface oxidation of the carbide particles progresses and eliminates the obstruction. The carbide particles Can be removed also by annealing in hydrogen, with similar results. But if the oxidizing anneal of 10 hr at 850°C in air is followed between in hydrogen for 75 hr at the Same temperature, grain growth is more hibition usually the whole specimen is transformed into a single crystal (approx. 1.5 cm X 5 cm). The reversed procedure, that is, hydrogen annealing followed by oxidizing annealing leads to smaller grains. Tangerding arrived at the logical conclusion that there must have been in his specimens some additional obstruction to grain growth hibition from a minor impurity, other than carbon. It seems likely that this obstruction was caused by an oxide formed during the oxidizing anneal and gradually reduced rtain the subsequent hydrogen-annealing. Other instances of grain growth inhibition of varying severity, associated with a dispersed second phase, have been described by several authors. Notable examples: lead with 0.06 pet Cu or Ni,24 cartridge brass with 0.12 pct Cr,25 or with up to 0.15

Jan 1, 1949

Quarrying and crushing 500 tons of limestone plus burning some 240 tons of limestone per day are the two initial phases in the production of borax, soda ash, sodium sulfate and related chemicals at Stauffer Chemical Co.'s plant in Westend, Calif. These processing steps have been upgraded in recent years by the installation of new primary and secondary crushers, an 8 x 340-ft rotary kiln plus kiln feed, control and cooling components-all designed and manufactured by Traylor Engineering and Manufacturing Division of Fuller Co. As a result of this new equipment, a new product- quicklime-has been added to the West End product family and considerable reductions have been realized in fuel and manpower costs.

Jan 1, 1965

By J. W. Cunningham, W. A. Tiller, D. H. Lane

The effect of ultrasonic vibrations on ingot solidification has been considered both theoretically and experimentally. The theoretical section elucidates the mechanisms by which the ultrasonic vibrations might refine the ingot structure. The experimental section describes a very efficient means of introducing the ultrasonic vibrations to the freezing interface. The application of this technique to the consumable-electrode arc melting process shows that the columnar mode of freezing may be effectively suppressed yielding an ingot structure consisting predominantly of equiaxed grains. The results support the contention that the ultrasonic vibrations increase the nucleation frequency in the layer of liquid adjacent to the freezing interface. CERTAIN structural characteristics of as-cast ingots are undesirable since they create considerable difficulty for subsequent processing and often produce defects in the finished product. These structural defects are illustrated in Fig. 1(a), and are: 1) planes of weakness where columnar grains growing from the different mold faces meet, 2) strength anisotropy due to the preferred orientation of the columnar grains and 3) inhomogeneity due to segregation at dendrite boundaries within the columnar grains and at the columnar grain boundaries. The type of ingot structure that eliminates 1) and 2) and diminishes 3) is the fine-grained equiaxed structure illustrated in Fig. 1(c). Many attempts have been made to produce the desirable ingot structure illustrated in Fig. 1(c) by inoculating, casting with varying superheats, vibrating or stirring, or by irradiation with ultrasonic vibrations. These attempts have met with various degrees of success, the ingots generally having the structure illustrated in Fig. 1(b). All four methods have been the subject of numerous investigations,1"4 the latter producing the most erratic behavior and inconsistent success. The method of ultrasonic irradiation during ingot solidification has shown considerable promise on small-scale ingots (diam 2 in.) but has not yet been successfully adapted to large-scale operation. The present paper considers the application of ultrasonic radiation to ingot solidification both theoretically and experimentally. The purpose of the paper is to elucidate the mechanism by which ultrasonic energy refines the ingot structure and to describe a method for producing the desirable ingot structure in both laboratory scale experiments and in ingots of commercial size. THEORY Conventional Casting—Before discussing the possible effects of ultrasonic radiation upon ingot structure let us first briefly review the reasons for the breakdown of columnar crystallization to equiaxed crystallization during ingot solidification. The following is a slightly oversimplified description. In the conventional method of casting, the alloy having a certain degree of superheat, T, is poured to fill a cold mold which is at room temperature, Tc,. Due to conduction of heat through the mold wall the outer rim of liquid metal cools rapidly to the liquidus temperature and begins to supercool. At some degree of supercooling, nuclei of solid form at random in this supercooled layer at the mold surface. The grains in this chill layer begin to grow inwards producing a solute build-up, thus lowering the freezing temperature at the interface as illustrated in Fig. 2. As growth proceeds, the temperature gradient in the solid conducts away not only the latent heat of fusion evolved during growth but it also conducts away some of the superheat of the melt so that the temperature

Jan 1, 1961

By J. T. Eash, W. S. Crowell, E. M. Wise

The practice of dentistry, particularly the construction of artificial dentures and "bridges," involves a unique and difficult application of the precious-metal alloys. Appliances used in the mouth are continuously exposed to corrosive agencies which can hardly be described as mild, and must remain free from tarnish and be substantially immune to corrosion. Limitations with respect to space and weight demand high physical properties, while complexity of form requires ease of working. The high corrosion resistance required necessitates the use of alloys of high precious metal content. The usual expedient of resorting to mechanical working to produce the requisite strength and stiffness cannot be utilized because of the frequency of annealing and soldering operations. To meet these difficult conditions manufacturers of dental goods were early led, unknowingly perhaps, to the production of precipitation-hardening or temperable alloys. The excellent properties of iridium-platinum may have suggested the addition of platinum metals to the conventional gold-silver-copper alloys to produce greater strength and hardness. It was found that such quarternary alloys retained their high physical properties after passing through the usual soldering process; i. e., heating to 750° to 800" C. and cooling naturally in the air. Later it was discovered that they could be softened and rendered more ductile by heating to the same temperature and quenching in water. These early examples of precipitation hardening, for years the common knowledge of dental practitioners and laboratory technicians, escaped the attention of the scientific world and discovery of the transformation which was responsible for this hardening was disclosed by the Russian investigators of the system Au-Cu, Kurnakow, Schemtschushny and Zasedatelev~,(~)$ although the optimum conditions for securing good properties in aged alloys were not given attention.

Jan 1, 1932

By R. H. Foley

It is difficult to consider any seam as unsuitable for longwall mining operation for something like 95% of British coal is produced by this system. The following is a brief report on how they do it-their techniques and equipment. Depth of working in British mines varies from about 150 ft to more than 3000 ft, with the average being about 1300 ft. Average seam thickness is approximately 40 in., but working seams vary from 16 in. to as much as 14 ft.

Jan 8, 1965

The following figures (Nos. 1-4) and tables (Nos. 1 and 2) were inadvertently omitted from the chapter entitled "Optimum Open-Pit Mine Production Scheduling" by Thys B. Johnson, Section 4, pages 539-562. [ ]

Jan 1, 1969

By F. E. Werner, B. L. Averbach, Morris Cohen

THAT bainite formed near the M, temperature bears a striking r esemblance to martensite tempered at the same temperature has been shown by the electron microscope.' By means of electron diffraction,' it has been established that carbide and cementite are present in bainite formed at 500°F (260°C); these carbides are also found in martensite tempered at 500°F (260°C).' The investigation reported here is concerned with an X-ray study of the matrix phases in lower bainite and tempered martensite. These phases have turned out to be dissimilar in structure; the matrix of bainite is body-centered-cubic while that of tempered martensite is body-centered-tetragonal. A vacuum-melted Fe-C alloy containing 1.43 pct C was studied. Specimens of 16 in. diam were sealed in evacuated silica tubing and austenitized at 2300°F (1260°C) for 24 hr. One specimen was quenched into a salt bath at 410°+7 °F (210°+4°C), held for 16 hr, and cooled to room temperature. The structure consisted of about 90 to 95 pct bainite, the re: mainder being martensite and retained austenite. A second specimen was quenched from the austen-itizing temperature into iced brine and then into liquid nitrogen. It consisted of about 90 pct martensite and 10 pct retained austenite. The latter specimen was tempered for 10 hr at 410°+2°F (210°+1°C). The specimens were then fractured along prior austenite grain boundaries (grain size about 2 mm diam) by light tapping with a hammer. Single aus-tenite grains, mostly transformed, were etched to about 0.5 mm diam and mounted in a Unicam single crystal goniometer, which allowed both rotation and oscillation of the sample. Lattice parameters were measured by the technique of Kurdjumov and Lyssak. This method takes advantage of the fact that martensite and lower bainite are related to austenite by the Kurdjumov-sachs orientation relationships Thus, the (002) and the (200) (020) reflections can be recorded separately, permitting the c and a parameters to be determined without interference from overlapping reflections. According to these findings, the matrix phase in bainite is body-centered-cubic and, within experimental error, has the same lattice parameter as ferrite (2.866A). On the other hand, martensite, tempered as above, retains some tetragonality, with a c/a ratio of 1.005t0.002. Most workers in the past have assumed that bainite is generated from austenite as a supersaturated phase, but the nature of this product has not been established. The question arises as to whether bainite initially has a tetragonal structure and then tempers to cubic, or if it forms directly as a cubic structure. If it forms with a tetragonal lattice, it might well be expected to temper to the cubic phase at about the same rate as tetragonal martensite. The martensitic specimen used here was given approximately the same tempering exposure, 10 hr at 410°F, as suffered by the greater part of the bainite during the isothermal transformation. About 50 pct bainite was formed in 6 hr at 410°F. On tempering at this temperature, martensite reduces its tetragonality within a few minutes to a value corresponding to 0.30 pct C.' Further decomposition proceeds slowly, and after 10 hr the c/a ratio is still appreciable, i.e., 1.005. Thus, even if the bainite were to form as a tetragonal phase with a tetragonality corresponding to only 0.30 pct C, which might be assumed to coexist with e carbide, it would not be expected to become cubic in this time. It seems very likely, therefore, that bainite forms irom austenite as a body-centered-cubic phase and does not pass through a tetragonal transition. The carbon content of the cubic phase has not been determined, but it could easily be as high as 0.1 pct, within the experimental uncertainty of the lattice-parameter measurements. It has been postulated that retained austenite decomposes on tempering into the same product as martensite tempered at the same temperature. There is now considerable doubt on this point. The isothermal transformation product of both primary and retained austenite at the temperature in question here is bainite," and the present findings show that bainite and tempered martensite do not have the same matrix. Acknowledgments The authors would like to acknowledge the financial support of the Instrumentation Laboratory, Massachusetts Institute of Technology, and the United States Air Force.

Jan 1, 1957

By R. F. Ashton, D. S. Thompson

In reporting results of precipitation hardening experiments, it is customary to include such conditions as solution heat-treatment temperature, specimen size, and quench medium as well as the aging time and temperature. One portion of thermal history that is often overlooked is the effect of the heating rate employed to achieve the aging temperature. It is the intent of this note to demonstrate the importance of the rate of heating to aging temperatures. This work was carried out on the aluminum alloy 7075 aged at 162oC, a temperature commonly used to obtain stress corrosion resistant tempers. A 2 in. thick plate of 7075 was quenched into 24°C water after solution heat-treatment for 2 hr at 470°C. Approximately 13 in. around the periphery of the plate was discarded to minimize quench rate variations, and the remainder was divided into 0.5 by 1.8 by 2.0 in. blocks which were held at room temperature, 24oC, for 4 days. This aging, or incubation period, at room temperature allowed a copious supply of GP-zones to form. Blocks were then heated at various rates to 162oC using the practices shown in Table I. Both single- and two-step aging practices were employed for each heating rate. The single step consisted of heating directly to temperature at the indicated rate while the two-stage practice included an interruption of heating for 7 hr at 107°C. In the case of the two-stage 100°C per min heating rate experiment, the specimens were returned to room temperature after 7 hr at 107°C where they were held for 16 hr be-fore finally heating at this rate to 162°C. This devia-tion in practice is not considered to be significant. Blocks were removed after various times at 162oC, and aging curves were determined from duplicate R. F. ASHTON and D. S. THOMPSON,Member AIME, are Senior Scientists, Metallurgical Research Division, Reynolds Metals Company, Richmond. Va. Manuscript submitted December 2. 1968. IMD Table I. Aging Practices Two-step Single-Step Heating Rate* Aging Aging Heating Method oC per Min A B Programmed Air Oven 0.23 * 0.01 C D Programmed Air Oven 0.93 ? 0.03 E F Air Oven at Temp -10 G H Oil Bath at Temp ˜100 *Heating rate was measured with a thermocouple at the center of a specimen. An average value between the starting temperature and 3°C below the aging temperature is reported for practices E-H. PRACTICES 70 — A B C E and G 50 - 2 4 6 810 20 40 60 HRS.AT 162°C Fig. 1—The influence of processing variables on 7075 aging curves. Fig. 2—7075 aged according to practice H (single-step aged, fast heating rate) for 3 hr. Magnification 100,000 times.

Jan 1, 1970

By Anthony Anable

HOOVER DAM, rapidly nearing completion in the Black Canyon of the Colorado River at Boulder City, Nev., taxes the superlatives of the vocabulary to describe. For by all odds, it is the largest construction project of its type ever essayed by man and the plants providing the essential materials of construction are also in a class by themselves not only in size but in advanced design, mechanization, and accurate control. Picture, if you will, the great aggregate plant, as it is called, situated about 4 mi. upstream from the site of

Jan 1, 1934

THE following employment items ore made available to AIME members on a nonprofit basis by the Engineering Societies Personnel Service, Inc., operating in cooperation with the Four Founder Societies. Local offices of the Personnel Service ore at 8 W. 40th St., New York 18; 100 Farnsworth Ave., Detroit; 57 Post St., Son Francisco; 84 E. Randolph St., Chicago 1. Applicants should address all mail to the proper key numbers in care of the New York office and include 6c in stamps for forwarding and returning application. The applicant agrees, if. placed in a position by means of the Service, to pay the placement fee listed by the Service. AIME members may secure a weekly bulletin of positions available for $3.50 a quarter, $12 a year. MEN AVAILABLE Graduate Mining Engineer, 31, married. Six years' engineering experience, mining and construction, U. S. A. and Alaska. Underground metal mining, production, development, geology, mine engineering. Engineering on airfield construction, earthwork, location work, mapping, topography, road location; office work. Commercial pilot license. Desires position mining or construction. Available 45 days. Prefer Latin America. M-676-477-E-8-San Francisco. Mining Engineer, 42, married, one child. Fourteen years' mining with much supervisory experience in developing and operating metal mines; also mine safety engineering. Familiar with many large and small mines in the western U. S. and Mexico. Excellent references. M-677.345-E-1¬San Francisco.

Jan 1, 1952

By D. E. Wolfson, H. J. Gluskoter, M. R. Geer, John A. Harrison, H. F. Yancey, I. S. Latimer

When this chapter was prepared for the kst edition in 1942, continuous mining machines virtually were unknown, and hand loading in underground mines, which gave an opportunity to discard impurities, accounted for 55 percent of the production of bituminous coal and lignite as compared with the 1965 figure of 11 percent. Only 24 percent of the total production was cleaned mechanically, compared with the present (1965) figure of 65 percent. The amount of refuse discarded during preparation for the same period increased from 13 to 21 percent. Changes in the equipment used in the cleaning process were as follows: [ ] Unclassified nearly 8 percent. Data on the amount cleaned by flotation was not collected until 1960 when 1.8 million net tons was so treated. In 1965 this figure increased to 6.9 million tons. Although the great increase in mechanization and full seam mining has resulted in substantial increases in the impurity content of the raw coal as well as in a finer size consist, some phases of face preparation are still important, particularly the variability of the distribution and thickness of the interbedded impurities and the changes in the character of the roof and floor from place to place in the mine. Knowledge of these factors in relation to all phases of the mining operation, particularly selective mining, are still of importance to the treatment of raw coal in the preparation plant. The major characteristics of coal and impurities from the standpoint of mechanical cleaning are particle size composition, generally called size consist, density differences, the relative friability of the coal and of its associated impurities, hardness, and strength. Some of the other factors related to preparation are petrographic composition and rank. COAL PROPERTIES Rank Perhaps 95 percent or more of the coal cleaned mechanically is of bituminous rank. Only a very small tonnage is subbituminous and prac-

Jan 1, 1968

By AIME AIME

TRADITIONALLY, the Annual New York Meetings of the A.I.M.E. cover four days, but the program is growing on each end as well as in the middle, and this year it lasted from 3 p. m., Sunday, Feb. 16, when the Education Division got under way, to 8:40 p. m., Friday the 21st, when a trainload of electrical inspectors, pro tern, got back fro111 the General Electric plant at Schenectady. The meeting has ceased to be a mere three- ring circus: on Wednesday afternoon eight sessions were being held simultaneously in the Engineering Societies Building, if one includes the Woman's Auxiliary, and according to frequent testimony one should include the W. A. as one of the most important units in Institute affairs.

Jan 1, 1936

By Phillip B. Bucky, Fred D. Wright

The present known petroleum reserves are limited, and unless important new fields are discovered the Nation will be dependent, in the not too distant future, upon imports or upon synthetic liquid fuels to supplement domestic petroleum supplies. As a national defense measure, it would appear desirable to develop a substitute source of liquid fuels within the borders of the country if new discoveries of petroleum should Prove disappointing. Congress undoubtedly had this in mind when it passed the Synthetic Liquid Fuels Act (78th Congress, approved April 5, 1944). The act directed the Bureau of Mines to construct and operate demonstration plants for producing synthetic liquid fuels from coal and oil shale, and from forestry and agricultural products. As a part of this program, the Bureau of Mines has built a demonstration plant at Anvil Points, near Rifle, Colo., for retorting the oil shale, and has developed a mine to supply the plant with oil shale. At the beginning of mining operations, the physical qualities of the oil shale, which would have a bearing upon the selection of mining methods and practices for exploiting the deposits, were largely unknown. A comprehensive mining-research program has been set up to determine the best methods and practices to follow to obtain the lowest overall practicable mining cost for producing the oil shale on a large scale. Unusually low mining costs will be necessary for shale oil to be produced commercially. Consideration now is being given to exploiting a series of flat-lying beds 70 ft thick by a room-and-pillar method of three benches with the advance heading at the top. This report is one of a series giving the results obtained in research on mining problems, The structure and physical qualities of the oil shale indicate that the 70-ft interval of the oil-shale measure can be safely mined in open stopes; studies indicate that this method would be the most economical one to use.' As labor will be a major item of expense, the largest equipment that could be operated efficiently in the workings would be required to obtain the lowest practicable mining Cost. It Was therefore desirable to know the maximum safe span of unsupported rooms and the size of pillars necessary to support the overburden. This paper describes the work done at the Columbia School of Mines Barodynamic Laboratory in determining the maximum safe unsupported roof spans and the minimum safe pillar dimensions for the oil-shale mine at Rifle, Colo.

Jan 1, 1949

By W. A. Tiller, W. C. Johnston

A high-temperature electromagnetic stirrer is described in which heating and stirring are accomplished by independently controlled power sources. The appavatus is suitable lor use at temperatures up to 1700°C in a variety of ambient atmospheres. Some typical examples of the homogenizatimz capabilities of the system are given. THERE are few processes in solidification that are not markedly affected by motion in the melt during freezing. In many instances, the mechanisms are diffusion-controlled, and the transport in the melt may be greatly accelerated by deliberately stirring the melt. In zone-refining, stirring1 assists the removal of rejected impurities from the interface, so the process proceeds at a faster rate. The transition from a planar to a cellular interface is caused by constitutional undercooling in the melt ahead of the interface: and stirring delays its onset. Stirring is valuable for homogenization of melts: and chemical reaction with sluggish kinetics may be accelerated. Finally, it has been observed that grain refinement is related to motion in the melt. Fine grain castings are usually produced by the addition of catalysts to the -melt,' catalysts which are thought to act simply as hetereogeneous nucleation centers. Even here motion is important. Richards and Rostoker 5 applied ultrasonic vibration to a solidifying A1-Cu alloy which had been innoculated with a catalyst and found that the grain diameter fell linearly with the amplitude, the peak acceleration and the power input to the melt from the transducer. Finally, mechanical and electrical stirring alone have been used to generate a fine-grained structure.6,7 Johnston ef a1.' have carried out a series of systematic investigations of grain refinement by electromagnetic stirring in a number of low melting point alloys. They found, for example, that the number of grains per unit volume in Pb-Sn alloys could be increased several orders of magnitude by stirring an undercooled melt at the moment of recalescence. In general, a relation AT .H = constant prevailed for a given grain size, where AT was the undercooling of the melt and H the field strength. In more recent work, deliberate homogeneous nucleation of slightly undercooled melts established that the mechanism of refinement must be one involving crystal fragmentation and subsequent multiplication, rather than a "shower" of nuclei effect.9 It is the purpose of this note to describe a stirring device suitable for use up to 1700°C. At low temperatures mechanical stirring and direct-current methods are feasible, but at high temperatures the problem of a protective atmosphere and of electrode corrosion rules out such procedures. The most convenient method for high temperatures is to use externally generated ac fields for both stirring and heating. With rf induction heating alone, considerable stirring and agitation can be achieved, but in general the penetration of field into the melt is small, and the stirring cannot be controlled independently of the heating. In the present experiments, separate power sources of different frequencies for heating and for stirring were used. A susceptor design was chosen so that the 450 kc rf heating field was completely absorbed in the susceptor. The stirring frequency, 400 cps, hereafter called the af field, was chosen so that a high penetration of the melt proper was achieved. EXPERIMENTAL APPARATUS The apparatus, Fig. 1, consists of a quartz tube and end plates, surrounded by an rf induction coil and six equally spaced af stirring coils, four of which are shown in full and a fifth in section. Each af stirring coil is a transformer of which the secondary is a single-turn water-cooled copper loop and the primary is composed of two 10 amp-117 v Variac cores as shown. These cores are cooled by forced air, as each of the six pairs will carry maximum currents of 15 amp for short periods. Each set of Variac windings are connected in series, but opposite sets are connected in parallel with a three-phase 400 cps 400-v source. By properly phasing the coils in this way, a rotating field is produced. Capacitors C1, C2, and C3 in Fig. 2 are used to match this inductive load to the generator. Fig. 3 shows a cutaway view of the quartz tube. The sample (1 in. diam by 1 in. high) is placed in a tapered alumina crucible. An axial W-26 pct Re thermocouple, enclosed by a protection tube, is provided. The cruci-

Jan 1, 1968

By Edna A. Dancy, Gerhard J. Derge

The specific conductance of FeOx,-CaO melts in contact with iron was found to decrease from 200 ohm-1 cm-1 for FeO, to 40 ohm-1 cm-1 for a melt containing 26.3 pct CaO at 1400°C. The temperature coefficient was positive at all compositions, but became smaller at high CaO contents. Current efficiencies for electrolysis increased from 2.5 pct in FeOx to 17.3 pct at the high CaO composition, indicating a change from predominantly electronic conduction to conduction with a substantial ionic contribution. It was shown that Ca++ ions as well as Fe++ ions carry the ionic current. A subsidiary investigation on the apparent effect of atmospheres of argon, helium, and nitrogen on the electrical conductivity showed that this could be correlated with surface temperature losses, which varied with the thermal conductivities of the gases and resulted in precipitation of metal by the reaction 3 Fe++ = 2 Fe+++ + Fe. The work described in this paper is offered as a contribution to the general fund of knowledge concerning metallurgical slags. Measurement of electrical conductivity and electrolysis are comparatively trouble -free methods for investigating molten materials, but, although these methods had been used for complex slags, it was not until the work of Bockris et al.1 that the approach of examining simple binary slag systems was employed, and CaO-SiO2, MnO-SiO2, and Al2O3-Si9 were studied. Two groups have performed work of particular relevance to the present investigation. Inouye, Tomlinson, and chipman2 studied the conductivity of wustite as a function of temperature and of the addition of 5 mol pct of a number of oxides, including CaO. They concluded that molten FeOx in equilibrium with iron is a semiconductor. Simnad, Derge, and ceorge3 demonstrated the ionic nature of liquid iron silicate slags and also concluded that, although the conductivity of FeOx in equilibrium with iron is predominantly electronic in nature, there is a small ionic contribution. The work reported here on FeOx,-CaO slags consists of three main parts, namely, the determination of the specific conductance over a wide composition range, an investigation into the nature of the conductivity through current-efficiency measurements over the same composition range, and an attempt to identify the current-carrying ions, as well as a subsidiary investigation on the apparent effect of the nature of the inert atmosphere on the conductivity. EXPERIMENTAL Materials. The slags, varying in composition from FeOx to 27 pct CaO, were prepared by heating reagent- grade Fe2O3 in an ingot iron crucible with a suitable amount of CaCO3 and, in some cases, powdered iron, in air. This prefused material was then used for the runs. At the end of each run the cell was removed from the furnace and quenched by immersing the bottom half in water. After crushing, the slags were analyzed for calcium and total iron by the usual wet methods. The oxygen content was obtained by difference. Specific Conductance: Apparatus and Method. Fig. shows the experimental setup, with the conductivity cell and leads of ingot iron. The standard four-probe method for measuring high conductivities was used. In this, the potential drop across the unknown resistance is compared with the potential drop across a known resistance connected in series, i .e., same current through both resistances. Thus there are both current and potential leads to the center electrode and to the crucible, which acts as th other electrode. Both ac and dc circuits were available for the measurements; they have been described in earlier work performed in this laboratory.4,5 The geometry of the cell was such that the center electrode was equidistant from the bottom and sides of the crucible. This ensured that the current path was the same irrespective of the magnitude of the conductivity of the material in the cell. Cell constant were measured with KC1 or NaCl solutions, which have considerably lower conductivities (0.0013 to 0.25 ohm-' cm) than the slags, and this precaution in design made sure that the determined cell constants applied to the cells with contents of any conductivity. The cell-constant determinations were made with the ac measuring circuit to prevent polarization. The four-probe method eliminates lead resistance but not the resistance of those parts of the center

Jan 1, 1967