Search Documents

By Max Roesler

I. INTRODUCTION THE following article concerns the geological occurrence of the iron-ore deposits on the south coast of Cuba. The article is based on a detailed field study, made in the hope that some information would I gained which might be of value in the search for further orebodies, Or in the economic development of the ore already found. LOCATION The iron-ore deposits of the Firmeza district lie near the coast, in the southeastern part of Cuba, in the Province of Oriente. The orebodies of this district form part of a belt of deposits that extends from Sigua, 25 miles east of Santiago, to Sevilla, 5 miles east of Santiago, and lies on the seaward slope of the Sierra Maestra range of mountains.

Jan 10, 1916

By H. E. Biber

DURING the production of tin plate a thin layer of FeSn2, is formed at the interface between the steel sheet and the protective tin coating. Because excessive amounts of this alloy layer are undesirable, the kinetics of its formation is a subject of interest in the tin-plate industry. A recent study of this subject at our laboratory uncovered a relationship which should be of general interest to anyone studying kinetics of reactions in metallic systems. It had been previously concluded that, at any given temperature in the range 175" to 330°C, the Fe-Sn alloy layer would have a parabolic growth rate.1,2 However, our studies showed that this rule apparently holds only when the tin plate is heated very slowly to the "reaction" temperature; when the tin plate is rapidly heated, considerably different growth rates occur. An example of this effect of heating rate on growth behavior is contained in the accompanying results of alloy-layer growth measurements at 240°C in oil baths stirred at 10,500, 1800, and 0 rpm. The heating curves for these three conditions are given in Fig. 1, and the growth data are presented in Fig. 2. With the rapid heating rate, provided by the stirring at 10,500 rpm, the alloy layer had three distinct stages of growth. In the initial stage, which persisted well beyond the time required to heat the tin plate to bath temperature, the alloy layer formed very rapidly. The growth followed a rate law of the form w = ktn where n > 1. This initial stage was followed by a growth-retardation stage of about 50-sec duration in which little additional alloy was formed. In the third stage the growth again followed a rate law of the form w = ktn, but here « =0.3. With the intermediate heating rate provided by stirring at 1800 rpm, the three-stage nature was less pronounced and the slope of the third stage increased (i.e., n > 0.3). With the slow heating rate provided by the unstirred oil bath, the alloy layer grew in two stages. The initial rapid-growth stage persisted only until the specimen was heated to bath temperature, no growth retardation was observed, and the slope of the main portion of the plotted data was greater than in the stirred baths, having a value of almost 0.5. Similar results were obtained for other bath temperatures in the range 200" to 300°C. This effect of heating rate on growth behavior may be due to changes in the rate of nucleation of FeSn, crystallites. The iron and tin are in contact from the onset of heating. Thus the initial formation of FeSn, occurs not at the "reaction" temperature but rather while the tin plate is being heated to that temperature. Because nucleation is in general temperature-dependent, different heating rates could cause different over-all nucleation rates, which in turn could cause different growth behaviors. A more detailed discussion of the growth of Fe-Sn alloy layer and the effect of heating rate will be published shortly.

Jan 1, 1965

By H. Kazemi, G. W. Thomas, M. S. Seth

The double-porosity model of Warren and Root7 for examining pressure drawdown and buildup phenomena in naturally fractured reservoirs has been extended to intetpret interference test results. Both analytical and numerical solutions are presented. The practicality of some of the assumptions in the Warren-Root model was also investigated. The standard procedure for interpreting interference tests in naturally fractured reservoirs beretofore employed an equivalent homogeneous reservoir model. A comparison of our results with the equivalent homogeneous model indicates the latter is inadequate for early time responses. For late time responses, however, the simpler equivalent homogeneous model yields favorable results. Finally, the effects of well spacing and the magnitude of the interporosity flow parameter are briefly cited. INTRODUCTION Interference tests can be used to provide reservoir information not obtainable from conventional pressure drawdown and buildup tests. The technique involves measuring the response in one or more wells arising from a pressure perturbation introduced into another well. It has been. successfully applied to single-layer, homogeneous, unfractured, isotropic and anisotropic formations to arrive at values of well storage capacity and a measure of directional permeability.l The techniques of interference testing usually can be extended to heterogeneous systems, provided the permeability contrast between any existing rock layers is not excessive.9 In such cases, the practical interference effects in an observation well of an interconnecting heterogeneous reservoir can be predicted using an equivalent homogeneous model. The calculated properties are then average values. Russell and Prats2 have demonstrated the utility of this approach for a single-phase, two-layer system. For naturally fractured reservoirs, some different approaches usually are necessary. The major departure from homogeneous or nearly homogeneous reservoir treatment is to characterize the fractured system as an entity having "double-porosity"; namely, we suppose the existence of both primary and secondary porosity, where the former is contained within a systematic array of identical rectangular matrix blocks and the latter is contained within an orthogonal system of continuous, uniform fractures (see Fig. 1). It is sufficient to assume that the permeability of the rock matrix is so small that movement of reservoir fluids to the producing wells is entirely through the fracture network. This assumption has been validated by Barenblatt3 and .employed by others?-7 Warren and Root7 used the double-porosity model to develop an interpretation of pressure drawdown and pressure buildup tests in naturally fractured

Jan 1, 1970

By G. F. Olsen

ON superficial consideration a technical library might be considered a luxury to the business institution that possesses one. After all, public libraries and research institutions probably contain all the data that would be found in a private technical library, and able consultants are available both within and without a company. In all probability the technical men of a company have in their combined personal libraries sufficient information to answer most inquiries. Nevertheless, possession of such a department is of real economic benefit because of the time it saves its users, because it prevents expensive duplication of technical literature in a company, and lastly, but most important, be- cause it makes readily available a central storehouse of technical facts classified and indexed to meet the demands of the industry or industries concerned.

Jan 1, 1940

By B. A. Wilcox, A. H. Clauer

DURING the course of an investigation on the high-temperature creep behavior of TD Nickel* (Ni + 2) vol pct ThO2), it was observed that the creep fractures were similar in appearance to low-temperature ductile fibrous fractures and creep ruptures by cavitation. Microfractographs of fibrous ruptures are typically characterized by a dimpled appearance, with second-phase particles frequently found near the bottom of the dimples.'-4 These somewhat resemble creep ruptures by cavitation, in that fracture occurs by void formation, with the subsequent growth and final merging of the voids to form a complete fracture.' It is the purpose of this communication to describe the creep fracture of TD nickel and suggest a mechanism for the rupturing process. The discussion is relevant to material crept to fracture in vacuo at a constant stress of 18,000 psi, over the temperature range 900" to ll00°C. The material used in this investigation was 1/2-in.-diam bar stock supplied by Du Pont, contain- ing 2.3 vol pct Tho2. The final fabrication treatment consisted of -95 pct reduction by swaging followed by a 1-hr anneal at 1000°C. Transmission and replica electron microscopy revealed that the material had a fibered structure with a transverse grain size of -1 µ and a longitudinal grain size of 10 to 15 µ. Selected-area diffraction indicated that the fiber axis was parallel to (00l), in agreement with the results of Inman et a1.6 The thoria particle size varied from 80 to 1000Å, with an average size of 400Å, and the mean particle spacing was about 1200Å. The remarkable structural stability7 was confirmed by annealing for 6 hr at 1300°C (about ' 0.9 the absolute melting point). Transmission electron microscopy revealed that the only structural change was a slight decrease in dislocation density. Furthermore, recrystallization or grain growth during creep has not been observed. All specimens were annealed in vacuo at 1300°C for 3 hr prior to creep testing. The following times to rupture were obtained for vacuum creep tests at a constant stress of 18,000 psi: 900°C, 854 hr; 930°C,

Jan 1, 1965

By H. B. Charmbury, D. R. Mitchell

Everyone in the coal industry from top management to the preparation engineer is vitally interterested in recovering as much salable coal as possible from the run-of-mine product. Coal losses from a preparation plant occur in the solid refuse material being discharged from the plant and in the bleed-off slurry from the water circuit. The refuse is generally hauled from the plant in solid form by trucks, conveyors, or aerial trams to the refuse or culm banks or it may be crushed and transported by hydraulic methods to refuse ponds or dams. The loss of coal in refuse material and the extent of this problem has been covered in another paver.' The loss of salable coal in the plant bleed-off slurry is one of the water circuit problems in coal preparation plants. Slurries originate at various places in the processing circuits and are usually disposed of by transportation to waste ponds known as slurry ponds. Even though the combustible material discharged as slurry and refuse from the plant is labeled a loss, the loss must only be considered temporary. There is a tendency at the present time to examine refuse and slurry losses and to reprocess these materials to recover valuable coal. Slurries from eight bituminous coal preparation plants in central and western Pennsylvania have been sampled and examined to determine the amount of recoverable coal in each. Examinations of the samples were made to determine the tons per hour of solids and the gallons per minute of water in the slurry; the size, ash, and sulfur analyses of the solids; and the sink-float characteristics of the larger solids. The extreme fines (—325 mesh material) from one of the samples has been examined further to determine the micron size fractions as well as the ash and sulfur content of the micron sizes. Collection of the Samples: Field trips were made to each of the plants where samples were obtained and discussions held with the preparation engineer prior to sampling. The flowsheet of the plant operation was studied and a time-period selected to obtain a representative sample. At least 20 1-gal samples of total plant bleed-off suspensions were collected at each plant in increments over designated periods belived to be typical of the plant flow Three of the samples were obtained from plants in the Pittsburgh area. Each plant supplied information on the capacity, operating time, type of cleaning equipment used, water and material balances, and auxiliary equipment. From the time required to collect given amounts of slurry and from the amount of solids in the slurry, total solids discharges from the plant were calculated and compared with the plant flow. Ash and sulfur analyses of the total solids were also checked, at some plants, with company figures. In all cases where checks could be made there was reasonable agreement between company figures and those reported here. Analysis of the Slurries: Representative fractions of properly agitated samples were examined in the laboratory to determine the specific gravities of the slurries. The solids and water were separated by filtration to check the weight of each so that the percent of solids in the pulp could be determined. From the resulting data, presented in Table I, it may be seen that the percent solids in the slurries ranges from 2.8 to 39.0 and the amount of solids from 2.61 to 45.61 tph. Size Analysis of Solids: Representative fractions of the slurries were permitted to settle and the clear water was removed by siphoning. The solids were then wet-screened at 28, 35, 48, 65, 100, 150, 200 and 325 mesh. Results of the size analyses are presented in Table 11. These results indicate the extreme variation of sizes and in most cases the degree of fineness of the solids. The amount of —325 mesh ranges from 22.5 to 84.5 pct and the amount of+200 mesh from 8.3 to 69.1 pct.

Jan 1, 1961

By R. E. Ray, J. W. Stevenson, J. A. Berry

Conventional concrete block plastered with a cementitious coating is the most common material used in the construction of permanent stoppings to direct airflow in underground mines in the US. All mines experience various degrees of strata convergence depending on depth of overburden, geological conditions, and type of roof support employed. Strata convergence will cause cracks and joint openings in masonry stoppings, resulting insignificant air leakage losses. Where strata convergence is severe, complete structural failure of the stopping can ultimately occur. Reconstruction of damaged or destroyed stoppings adds expensive overhead to mining operations, and even greater expenses are incurred from the additional fan horsepower required to overcome leakage losses. Ideally, a stopping should maintain high resistance to airflow while yielding to strata convergence. By properly incorporating a polyisocyanurate rigid foam material within the masonry block structure, stopping service life can be increased in mines experiencing strata convergence problems such as floor heave, roof loading, and lateral rib movement.

Jan 1, 1986

By James Barr

Geology and Mineralogy1 TENNESSEE phosphates are commercially divided into three varieties: Brown, blue and white. The first two only are now of commercial importance. The white phosphates of Perry county are not being mined at present owing to their pockety occurrence. The white phosphate is Fig. I.-DEPOSITS OF 75 PER CENT. BROWN PLATE ROCK UNDERLAIN BY SAND. the highest grade of the three varieties, running often more than 90 per cent. tricalcium phosphate. The brown rock is found in three varieties, grading from the dense almost vitreous gray rock, 76 to 82 per cent. tricalcium phosphate, down

Jan 9, 1914

By W. A. Krivsky, R. Schuhmann

Jan 1, 1962

By A. W. Fahrenwald

Flotation practice in Idaho is now about 13 years old. The advance has been steady during these 113 years. The operators have been alert to take advantage of the newest developments and they have themselves made a constant effort to improve their work. The metallurgical improvements are due to the development of (1) better equipment, (2) better reagents, and (3) better understanding and control of the process. During the eight years the writer has been in this district, there has been continuous experimentation by several companies to improve the ore dressing by flotation methods. Gravity concentration has fought hard to hold its place, and although it is true that gravity processes have been improved during this period, nevertheless, in several of the important mills of the district the few tables that managed to hang on have finally given way. On the straight-lead ores, tables and jigs are still used; and, due to better classification, their hold on this job has been strengthened. Ores of the District The ores of the district are of two general classes: (1) clean lead ores, such as those from the Bunker Hill and Hecla mines, and (2) complex lead-zinc ores. The general impression prevails that the clean lead ores, class 1, are simple and that it is easy to obtain high recoveries and good grade products. This, in a way, is a false impression; there is quite a high percentage of locked middling in these ores at 100 and' 150-mesh sizes. Improved classification preparatory to table treatment of this type of ore has made it possible to segregate effectively a high-grade middling which is further comminuted and floated. The complex lead-zinc ores of the district, of which the ore from the Morning mine of the Federal Mining & Smelting Co. is a typical example, always have presented a difficult problem. It always has been comparatively easy to make a clean lead concentrate, but it never has been possible to concentrate sphalerite with a specific gravity of 4.10 from siderite of gravity 3.88. Also, a large percentage of the galena and sphalerite of this class of ore refuses to separate out until the crushing has been carried

Jan 1, 1928

By E. P. Abrahamson II

The effect of transition elements which form binary solid solution upon the recrystallization temperature of zirconium has been investigated. All additions raised the recrystallization temperature. A correlation is obtained between the logarithm of the rate of change of recrystallization temperature with atomic percent solute and the free atom ground state electron configuration of the solute element. ThE work of Abrahamson, et al., on dilute binary solid-solution alloys indicated a correlation between the free-atom ground state electron configuration of the solute and either the brittle-ductile transition or recrystallization temperature. These studies were carried out on bcc base materials. The implication is that the outer s and d electrons of the solute are the prime determinant of the absolute rate of change of recrystallization or transition temperature. Furthermore, the limit of linearity has been shown to be a function of solute electron configuration for recrystallization in iron and vanadium. To date no Complete systematic recrystallization study of dilute binary zirconium base alloys has been made. It is the purpose of this study to note whether the change in solvent structure from bcc to hcp will influence the correlation. It was also desired to learn more of the role of the electron configuration of the solvent on recrystallization temperature. PROCEDURE All alloys were made using 99.87 pct Zr with 0.01 Cr, 0.04 Fe, 0.006 Hf, 0.003 Mg, 0.003 Mn, 0.003 N, and 0.080 0 (132 BHN). The solute elements were 99.9 pct pure. According to the published binary phase diagrams6 and metallographic examinations at X750, all alloys used were solid solutions. The alloys were arc melted and remelted six times in the form of cubic 200-g buttons under an argon atmosphere. They were then hot pressed at 950°C to 0.450 in., upset pressed to 0.350 in., and annealed at 800°C for 1 hr. The specimens were then Blanchard ground to 0.250 in., removing 0.050 in. from each side. The grain size of the material at this stage was found to be 8000 100 grains per sq mm. The specimens were then cold rolled to 0.130 in. and cold pressed to 0.125 in., yielding 50 1 pct cold work. All alloys were then chemically analyzed for the principal addition. The interstitial contents remained at the values of the starting material when checked on random alloy specimens. The rolled sheet was cut into 6.75 by 0.25-in. lengths and heat treated in a gradient furnace for 1 hr. The gradient was 250o to 900°C over the 6-in. length, recorded continuously by six thermocouples resting on each specimen. Control was 3oC, accomplished at the hot end. The recrystallization temperature was determined metallographically using polarized light. The criterion chosen was the point on the specimen showing the first recrystallized grain at a constant magnification, X200. Specimens were repeated, and the agreement was found to be 3°C. RESULTS Three different pure zirconium specimens were tested, and the recrystallization temperature was

Jan 1, 1962

By Frederick Laist

AFTER a series of experiments covering a period of about three years, ending from the spring of 19iJ.2 to the spring of 1915, a 2,000-ton leaching plant for the treatment of the accumulated copper concentrator tailing was built and put into operation. During the experimental period, the first step was that of laboratory experiments or beaker leaches. The results on this small scale were so satisfactory that a small operating plant, capable of handling 5 tons of roasted tailing per day, was installed. Again, the results proved satisfactory and an 80­ton plant was built and operated continuously from August until February, 1913. In this plant, full-sized roasting and leaching units were

Jan 8, 1916

By A. W. Schlechten, R. P. Abendroth

Jan 1, 1960

By H. M. Chance

Jan 1, 1886

By R. G. Turner, M. G. Hubbard, A. E. Dukler

Gas phase hydrocarbons produced from underground reservoirs will, in many instances, have liquid phase material associated with them, the presence of which can affect the flowing characteristics of the well. Liquids can come from condensation of hydrocarbon gas (condensate) or from interstitial water in the reservoir matrix. In either case, the higher density liquid phase, being essentially discontinuous, must be transported to the surface by the gas. In the event the gas phase does not provide sufficient transport energy to lift the liquids out of the well, the liquids will accumulate in the wellbore. The accumulation of the liquid will impose an additional back pressure on the formation that can significantly affect the production capacity of the well. In low pressure wells the liquid may completely kill the well; and in the higher pressure wells there can occur a variable degree of slugging or churning of the liquids, which can affect calculations used in routine well tests. Specifically, the calculated bottom-hole pressures used in multirate backpressure tests will be erroneous if the well is not removing liquids on a continuous basis, and gas:liquid ratios observed during such a test may not be correct. Several authors1,3,8,14 have suggested methods to determine if the flow rate of a well is sufficient to remove liquid phase material. Vitter14 and Duggan' proposed that wellhead velocities observed in the field would be adequate for keeping wells unloaded. Jones8 and Dukler3 presented analytical treatments resulting in equations for calculating, from physical properties, the minimum necessary flow rate. An analysis of these studies indicates the existence of two proposed physical models for the removal of gas well liquids: (1) liquid film movement along the walls of the pipe and (2) liquid droplets entrained in the high velocity gas core. Although there probably is a continuous exchange of liquid between the gas core and the film, they will be treated separately for the purposes of this study. The development and comparison of these separate models with experimental data will permit the determination of which, if either, is the controlling mechanism for the removal of liquids from gas wells. The Continuous Film Model Liquid phase accumulation on the walls of a conduit during two-phase gas/liquid flow is inevitable due to the impingement of entrained liquid drops and the condensation of vapors. The movement of the liquid on the wall is therefore of interest in the analysis of liquid removal from gas wells. If the annular liquid film must be moved upward along the walls in order to keep a gas well from loading up, then the minimum gas flow rate necessary to accomplish this is of primary interest. The analysis technique used follows Dukler2 and Hewitt5 and involves describing the profile of the velocity of a liquid film moving upward on the inside of a tube. The minimum rate of gas flow required to move the film upward is then calculated.

Jan 1, 1970

By Herbert A. Franke

ANY analysis of the aluminum situation, particularly of the factors involved in the current shortage of the metal, must consider the rapid march of events since the Munich fiasco of September 1938. At the end of 1938, the sole domestic producer of aluminum had more than a year's supply of metal on hand, having added 50,500 tons of output to stocks during the year. Not until war had been declared between the United Kingdom and Germany in September 1939 did the United States begin to make serious preparations for defense and a limited national emergency was proclaimed. Congress reflecting popular opinion, was not disposed to spend huge sums for armaments in 1939, and although 31,413 tons of aluminum was withdrawn from stocks. 107,500 tons was still on hand at the end of the year. When the President initiated a 50,000-airplane program in May 1940 the country was astounded, as previous Congressional authorizations of approximately 6000 planes for the Army by July 1911 and 3000 for the Navy by 1914 had been considered adequate.

Jan 1, 1941

By Y. Oka, H. Majima

When a rock particle is subjected to an external force, internal stresses and deformations are experienced by the particle. Assuming that the breakage of a rock is mainly due to tensile stresses generated by the action of a pair of concentrated loads, F, directed in compression towards the loading points at the shortest distance, as illustrated in Fig. 1, the stress and deformation experienced by a particle of irregular shape can be determined with the aid of the theory of elasticity. According to the photoelastic experiments made by one of the present authors,' the stress states in a rock particle of irregular shape are quite similar to that of an inscribed sphere of diameter x, as indicated in Fig. 1, but accompanied by the faint stresses, in the vicinity of the particle outside of the inscribed sphere. Therefore, the stress components in an irregularly shaped particle can be estimated by referring to stress components in a sphere. Applying polar spherical coordinates to an elastic spherical body, as shown in Fig. 1, the stress components are all expressed as multiples of F /x2 and more or less influenced by the loading angle and Poisson's number m. In general, the energy w, acting on a rock particle is defined as the product of loading compression F

Jan 1, 1970

By W. C. Maurer

A study of the mechanics of shear failure of rock under pressure has been made. The transition from brittle to ductile failure occurs when the friction along the fracture surfaces exceeds the shear strength of the rock. A machine has been developed for measuring both the shear strength of rock and the friction along rock fracture surfaces. In this shear machine, the fractures are forced along definite planes; as a result, the rock is stronger than in compression tests where the fractures choose the weakest paths through the specimens. Friction is composed of several forces: (1) the forces to slide irregulurities on surfaces over each other; (2) forces to shear some of these irregularities; (3) molecular attractions across the fractures; and (4) forces required to break bonds resulting from melting and welding at the tips of irregularities on the surfaces. Friction along rock fracture surfaces is not proportional to contact pressure as usually assumed; instead, it increases as the contact pressure raised to the 0.4 to 0.8 power. INTRODUCTION It is difficult to produce tensile stresses under the high compressive stresses present in the earth; therefore, in deep drilling and geological faulting, shear failure predominates. This shear failure mechanism is complicated because rock is a heterogeneous material containing pore spaces, microfractures, elastic discontinuities and other imperfections. A study of shear failure of rock under pressure has been made to obtain a better understanding of this complex mechanism. A machine has been developed and used to measure the shear strength of rock and friction along sheared surfaces. This machine has certain advantages over the compression test — shear properties can be measured under low normal stresses and shear stress and normal stress can be varied independently. The first part of this paper is a description of shear failure of rock under pressure. The role of shear strength and friction along fracture surfaces in the shear failure mechanism will be discussed. The second part consists of a description of the shear machine and a discussion of the shear strength and friction data obtained using this machine. It will be shown that shear strength depends upon the size of the stressed zone, and that friction does not increase linearly with contact pressure as usually assumed. Attempts are made to relate some of the new concepts to tectonic failure and to dril ling. SHEAR FAILURE IN ROCK TRIAXIAL TESTS The shear failure mechanism is illustrated by the triaxial test shown in Fig. 1. In this test, a cylindrical rock specimen is subjected to a confining pressure, PC, and an axial pressure, pa. These external pressures produce normal a and shear T stresses on inclined planes within the specimen equal to1 where 0 is the angle between the specimen axis and a normal to the inclined plane. Fig. 2 shows how triaxial specimens deform as the axial pressure is increased. The pressure is

Jan 1, 1966

By G. S. Baker, S. H. Carpenter

Langenecker has reported significant reduction in strength of high-strength metals during ultrasonic t'ibration. Decreases in static yield stress an order of magnitude greater than the calculated stress amplitude of vibrations were reported by him for a stainless steel and for tungsten. in the present work, attempts were nzadc to verify such large reductions in yield and flats stresses using resonant librations of measured amplitudes. The results show that both the soft metals (copper and aluminum) and the high-strength metals (sleels) hare reductions in yield and .flow stresses no larger than the stress amplitude of libration. BLAHA and Langenecker,' investigating the effect of vibratory stresses on the deformation of zinc and aluminum, found a decrease in the static yield and flow stresses approximately equal to the vibratory stress imposed. Langenecker later extending this work to high-strength metals such as stainless steels and tungsten2 found a much larger effect. In these metals the static yield and flow stresses decreased by an amount more than an order of magnitude greater than the calculated vibratory stresses. It was suggested that this phenomenon could be a serious hazard to high-strength structures in an acoustic environment, such as a large rocket at launch, or could be used advantageously in the working of hard-to-work materials such as the refractory metals. Langenecker and others3 have investigated the effect of high-amplitude vibrations on many metal-forming operations. The results have been quite favorable with usually a large decrease in the energy necessary for the forming operation. The processes, however, involve large frictional forces and it is not clear whether the decreases in forming forces are to be ascribed to decreased friction or to decreased flow stresses. The present paper reports an attempt to determine the effect of accurately known vibratory stresses on the static yield and flow stresses. I) EXPERIMENTAL TECHNIQUE The standard multicomponent resonator technique for measuring internal friction has been adapted to allow simultaneous high-amplitude vibration, internal-friction measurement, and tensile deformation. This has been described in detail elsewhere.4 Longitudinal oscillations of approximately 50 kc frequency are excited in a multicomponent resonator by a quartz transducer. A second transducer measures the amplitude of vibrations. Fig. 1 shows a schematic drawing of the resonator and grip arrangement and the displacement pattern produced. Since the centers of the dummy bars are at displacement nodes, they represent points where attachments will not materially affect the vibrations. The force is applied by a standard Instron tester. The sample may be deformed while simultaneously vibrating at up to 104 strain amplitude. 11) EXPERIMENTAL RESULTS The effect of high-amplitude vibrations on the yield and flow stresses of copper. aluminum, tantalum. a soft iron, and a stainless steel has been measured. In addition samples of tungsten vibrating at stress levels up to 10' dynes per sq cm have been subjected to static stresses near the static yield stress with no indication of macroscopic deformation. Fig. 2 gives typical results for 99.999 pct polycrys-talline copper. A vibratory stress of 7 x 107 dynes per sq cm is applied at points "a" and removed at points "h". The behavior of aluminum is identical. In agree-

Jan 1, 1967