Search Documents

By Leo P. Tarasov

Magnetic torque studies of ferromagnetic single crystals have been carried out in a number of laboratories during the last decade&apos;s2 and some work has been reported on polycrystalline material showing preferred orientation. Goss3 used the method extensively in developing electrical sheet with desirable magnetic properties, but he used it as a control rather than as a means of studying the texture. Bozorth4 made a quantitative correlation of a torque curve he obtained from some cold-rolled iron with the texture as determined from X-rays, but did not extend his studies beyond the one specimen. Other studies, which have been reported from time to time2,5 have also been incomplete in the sense that no effort was made to study a whole series of samples, differing only in degree of cold reduction or in the annealing temperature, in order to ascertain the effect of such treatments on the texture as revealed by torque measurements. It is the purpose of this investigation to make such a study, mainly in order to see how useful the method can be made when used under favorable circumstances and to find what kind of a correlation can be expected between magnetic and X-ray studies of texture. Before proceeding further, it is desirable to say a little about single crystals, so as to make clear the concepts involved in magnetic torque measurements. Magnetic Torque Method It is fairly well known nowadays that single crystals of ferromagnetic substances have directions of easy magnetization and of hard magnetization. In Fig. 1 are reproduced typical magnetization curves for a single crystal of iron, which show that in a < 100 > direction saturation occurs at low fields compared to those required to saturate the same crystal in a <110> or a <111> direction. (The magnetization intensity I is defined by the equation B = H + 4pI.) At fields high enough to

Jan 1, 1939

By W. H. Class

The embrittling effects of oxygen, ozone, nitrogen, air, and surface residues, on NaCl has been investigated. The embrittlement by ozone and oxygen was found to be associated with the formation of a NaClO3 surface compound. In these cases the initial crack that was responsible for fracture (in a bend test) always nucleated at the corners between the tension and side faces. The behavior of air was very erratic and on certain days did not produce enzbrittlement. During these periods, crystals that had become embrittled by the ozone treatment completely recovered their ductility after a short exposure to the ambient atmosphere, It was established many years ago1 that considerable ductility could be obtained in NaCl single-crystal specimens if the crystal surfaces were dissolved in water either during or immediately prior to the test. The original interpretation of this effect by Joffe attributed the enhanced ductility to the removal of surface microcracks by dissolution. Later investigations2&apos;3 have suggested that the exclusion of air from the specimen surface is the criterion for extensive plastic flow prior to fracture. The air em-brittlement in this later work was attributed to the diffusion of gaseous atoms into the surface layers of the crystal, thereby impeding the movement of dislocations. This model satisfactorily accounts for the reembrittlement observed after further air exposure subsequent to the water dissolution treatment. However, the situation has recently become more complex by the observations in several laboratories4-t that under certain conditions air exposure does not impair the ductility of NaC1. It has also been recognized5 that improper drying operations after water dissolution can leave surface precipitates that lead to embrittlement. Cleavage defects on as-cleaved crystals can often be another source of embrittlement. In the present work the effect of the gaseous atmospheres nitrogen, argon, air, oxygen, and ozone, on the ductility of rock salt was studied extensively. The embrittlement resulting from oxygen and ozone exposures was found to be associated with the formation of a NaC1O3 surface film. It is suggested that certain atmospheres, one of which often can be ambient air, which inhibit the formation or favor the decomposition of this compound, can promote ductility. Thus one aspect of the Joffe effect is certainly related to the removal of surface compounds or complexes by water dissolution. The effect of surface precipitates that remain after drying operations and of cleavage defects were also studied. In neither of the latter cases was the embrittlement as severe as that found with a NaClO3 surface layer. PROCEDURE AND SPECIMEN PREPARATION The nature of the embrittlement produced by the agents mentioned above was studied by means of microscopy, mechanical testing, and X-ray diffraction. Specimens were cleaved from large crystals of optical quality sodium chloride obtained from the Harshaw Chemical Co., and, except for those tested in the as-cleaved condition, were given a 15- to 20-sec immersion in distilled water followed by a rinse in absolute methyl alcohol. The specimens were then blotted on a soft, absorbent paper, and dried by a few seconds exposure to a stream of warm, dry air. Such a procedure was found to give a control surface which was microscopically free of residues. (A few crystals were intentionally painted with a concentrated NaCl solution in order to investigate the effect of surface residues). All specimens were of 0.140 sq in. cross-section. Crystals prepared in the above manner were immediately placed in a gas train where they could be exposed to the desired gases for preselected periods of time. For the oxygen and nitrogen exposures, pure reagent-grade gases were employed. The ozone was provided in the form of an ozone-oxygen mixture (approximately 10 pct ozone) prepared by passing commercial grade oxygen over a strong ultraviolet light source. All gases were dried prior to their introduction into the train. Since argon was found to be completely inert in its behavior (i.e., residue-free specimens that were exposed to argon were not embrittled), it was periodically utilized to check the control specimen surfaces as well as the condition of the gas train used for aging the specimens. After exposure to the gaseous media in question, the crystals to be used for the measurement of the strain to fracture were transferred from the gas train to a protective oil bath (without further exposure to the atmosphere) where the tests were conducted in three-point bending. The apparatus was so adjusted that the load could be applied at a constant, continuous rate. Other Snecimens from the gas train were deformed

Jan 1, 1962

By R. E. Zimmerman, Michael Sokaski, E. R. Palowitch, M. R. Geer, H. F. Yancey, W. Deurbrouck, S. C. Sun

PART 1: DENSE MEDIUM SEPARATION by M. SOKASKI, M. R. GEER and H. F. YANCEY INTRODUCTION In the early days of coarse-coal treatment by the dense-medium process in Europe, loess was one of the materials used for medium solids. Newly developed cyclones were used to reclaim and thicken :he loess suspension. On occasion, when the cyclone thickener at the Maurits mine in the Netherlands plugged, the overflow was found to be filled with clean coal free of impurity. From this observation stemmed the concept of the cyclone as a cleaning device. Development took place during World War 11 in the laboratory of the Dutch State Mines under the direction of M. G. Driessen. A 15-ton-per-hour pilot plant was in operation in the laboratory by 1945, when, in September, Driessen made the first public disclosure of the process in a paper presented to the Institute of Fuel in London. In April 1945,2 operation of this pilot plant was observed by one of the authors, who was so impressed with the potential of the cyclone process that, on his return to the United States, a research program on the cyclone was started by the Bureau of Mines immediately. This work led to an AIME paper in 1946 in which the first details of cyclone operation on American coals was made available. Commercial adoption of the cyclone proceeded in Europe, initially in the Netherlands, Germany, and France. In the United States, where coal is less costly and most of the coals are so easy to clean they respond well to simpler cleaning systems, the first cyclone plant was not built until 1961.3 As of the spring of 1967, a total of 31 commercial cy- clone plants had been installed or were under construction in the United States; this does not include eight Dynawhirlpool plants. The capacity of the cyclone plants ranges from 50 to 1300 tons per hour and totals 6600. THEORY Before discussing the theory of a dense medium cyclone, a brief description may be helpful to some readers who are not familiar with its basic operation. In a typical dense-medium cyclone, illustrated in figure 10-1, the mixture of medium and raw coal enters tangentially near the top of the cylindrical section, thus forming a strong vertical flow. The refuse moves along the wall of the cyclone and is discharged through the under- flow orifice. The washed coal moves toward the longitudinal axis of the cyclone and passes through the vortex finder to the overflow chamber.

Jan 1, 1968

By M. J. Duggin

Structural similarities between the E, X, and iron carbides are illustrated. Experimental evidence regarding phase transformations occurring during ternpering reactions in finely divided carbides, thin-film carbides, and carbides which occur in steels is considered and possible mechanisms for the E — x and x — 9 transformations proposed. HOFER1 has shown that within the appropriate temperature ranges carbon monoxide will react with finely divided a iron to form either iron carbide or x iron carbide. He has shown that at an elevated temperature the E iron carbide will transform to the x iron carbide (Hagg carbide) which, upon further elevation of temperature, will transform to 9 iron carbide (cementite). Jack,2,3 using X-ray diffraction methods, has observed that during the tempering reactions occurring in steel the E iron carbide formed in the first stage of tempering passes into two-dimensional platelets of 0 iron carbide during the second stage of tempering. The three-dimensional form of the 0 carbide is formed during the third stage of tempering. Jack suggested2 that the two-dimensional platelets of 0 carbide could be related to the faulted x iron carbide. Okada and Arata4 investigated a Swedish steel containing 1.05 wt pct C and approximately 1.0 wt pct Mn using permeability measurements at low field strength. A Curie point of 360°C was observed in the quenched steel, which indicated the presence of E iron carbide. On tempering at 400°C the specimen developed a Curie point at 230°C, indicating the presence of x iron carbide, and on tempering at 700°C the specimen developed a Curie point at 190°C which was assigned to 0 iron carbide. The carbides were extracted electro-lytically and the use of X-ray diffraction techniques4r5 indicated the carbide with a Curie point of 230°C to be x iron carbide. The Curie points of the carbides are 10 to 22°C lower than the accepted values which is probably due to the presence of manganese in the carbides, since it has often been observed (e.g., Ref, 6) that a partial substitution of manganese for iron in cementite will lower the Curie point of this carbide. Hofer&apos; summarizes additional evidence of the tempering reactions in steel in which E iron carbide, formed during the first stage of tempering, transforms to x iron carbide during the second stage of tempering. During the third stage of tempering, the x carbide disappears as the 0 carbide is formed. By carburizing thin iron films in a CO gas stream, ~a~akura&apos; has been able to produce the E, X, and 0 iron carbides. He found that below 250°C the E iron carbide was formed; between 250" and 350°C the x iron carbide was formed and above 350°C the 0 iron carbide was formed. He has shown that the E iron carbide transforms to form x iron carbide at 380" to 400°C and that the x ir°n carbide transforms to form the 0 iron carbide at approximately 550" C; both of these phase transformations are irreversible. Hofer&apos; presents a review of evidence to show that the sequence of reactions occurring during tempering processes subsequent to the formation of E iron carbide formed by the direct carburization of finely divided a iron is the same as the sequence of reactions which occur during the tempering processes subsequent to the formation of E iron carbide in steel during the first stage of tempering. It is evident from Nagakura&apos;s work that identical tempering reactions are found in thin films of iron which have been carburized to form iron carbide. The purpose of this paper is to discuss the structural similarities between the E, X, and 0 carbides and to suggest a possible mechanism by which regions of the E carbide, formed during the first stage of tempering, may transform to the x carbide during the second stage of tempering. For the finely divided or thin film carbides a mechanism will be proposed for the transformation of the x carbide to the 0 carbide during the third stage of tempering, although it will be suggested that there is evidence that such a transformation may not occur in steels. STRUCTURAL DATA OF THE E, X, AND 0 IRON CARBIDES € Iron Carbide. It is evident from X-ray diffractions and electron diffraction&apos;, investigations that the metal atoms in the E iron carbide form an hcp structure with lattice constants ah = 2.752A, ch = 4.3534, using electron diffraction, reports the lattice paramet$rs of the superlattice cell to be a = 4.767A, c = 4.354, c/a = 0.9134. He finds that the carbon atoms occupy the octahedral voids in the metal atom structure so as to form a hexagonal stacking sequence with its basal plane parallel to that of the metal atoms. Considerable long-range disorder occurs in the positioning of the carbon atoms, however, which is in agreement with the possible range of composition Fe2C-Fe3C discussed by Hofer.&apos; Barton and ale" have made X-ray diffraction measurements on a sample of E iron carbide extracted from a catalyst in an organic process. Although there were few reflections recorded on the obtained X-ray powder diffraction pattern, they have proposed that the structure could belong to one of the three possible space groups p3m1, P63/mmc, or Pbcn if one assumed the composition to be Fe2C. Nagakura, using electron diffraction data, suggests a space group of P 6322 for a specimen of c iron carbide of apparent composition Fez.&. x Iron Carbide. The x iron carbide has been studied by Duggin and Hofer" and by Jack and wild,&apos; who

Jan 1, 1969

By S. A. Mersol, C. T. Lynch, F. W. Vahldiek

The room-temperature Knoop hardness of single -crystal titanium diboride has been determined. Variations in microhardness have been correlated with orientation and structural imperfections in the crystals. Maximum differences in hardness values of 750 kg per sq mm with respect to orientation and 450 kg per sq mm with respect to substructure were found. The effects of etchants, load on indenter, and degvee of cracking of indentation were studied. The average hardness was determined as 2800 kg per sq mm on the as-grown crystals. Annealing increased the average hardness to 3375 kg per sq mm. ThE microhardness of polycrystalline titanium diboride approximating the stoichiometric composition TiB, has been studied by several investigators. The values for the Knoop hardness number range from 2710 kg per sq mm (Khn = 2710 kg per sq mm) to 3400 kg per sq mm.&apos;-4 Samsonov et al.&apos; reported a Vickers hardness number of 3400 kg per sq mm (Vhn = 3400 kg per sq mm) at 120-g loads for a 98 pct Ti + B material of 96 pct theoretical density. Recently Dunegan measured the Vickers hardness and obtained 2060 kg per sq mm with a 10-g load (Vhnlo = 2060 kg per sq mm), 1425 kg per sq mm for Vhnloo, and 1320 kg per sq mm for Vhnlooo. We have obtained a Khnloo = 3000 * 350 kg per sq mm for hot-pressed polycrystalline TiB2 that was 99.1 pct Ti + B and 96.6 pct of theoretical density. The present investigation has been made on single-crystal titanium diboride boules, and is believed to be the first such study on TiB, crystals of known orientation. EXPERIMENTAL The single crystals were prepared by a Verneuil-type process using an electric arc by the Linde Division of Union Carbide Corp. The largest specimens were 6 mm in diameter by 12 mm long. The crystals were of theoretical density (4.50 g per cm3) with a Ti + B content of 99.8 pct. The major impurities present were: 0.03 pct (by weight) 0, 0.06 pct C, 0.01 pct Si, 0.05 pct Fe, 0.01 pct Cr, and 0.01 pct Ni. The crystals were boron-rich, the average boron content being 31.S7 wt pct (stoichiometric value is 31.12 wt pct), and titanium-poor, the average titanium content being 68.2 wt pct (stoichiometric value is 68.88 wt pct). Titanium was determined gravimetrically by cupferron precipitation and boron by titration of H3B03 from a NaOH-fused specimen after removal of titanium with BaC03. The outer edge of the boule accounted for some of the excess boron. An electron-microprobe analysis showed that the titanium content increased from 60.0 wt pct at the edge to 68.5 wt pct at D, ~ 1000 p, where D, = distance from outer edge (see Fig. 5). X-ray measurements indicate that the boules are single crystals with considerable substructure. Upon etching this structure is seen in the form of a Widmanstatten-type rhombohedral line pattern in the basal (c) plane and a parallel "lines" pattern in the prism (a) planes. A typical WidmanstHtten-type pattern is seen in in Fig. 1. Electron microscopy reveals that the lines are less than 1 p across, which does not allow direct electron probe or microfocus X-ray determination of their composition. The identity of the second phase has not been established. It might be a higher boride or a nonstoichiometric TiB2. On annealing above 2200°C the precipitate is dispersed and dissolves in the matrix. The best etchants found were HF/HNO/HO, KF(CN)$NOH/HO (Murakami&apos;s Etch), and A large number of other etchants were previously Studied. The acidic etchant produced an acicular or "needles" pattern in the (a) planes which is an etchant effect on the "lines" pattern.

Jan 1, 1965

By Frank R. Barnako

Coal mining is a hazardous occupation, but tremendous progress has been made in reducing accidental injuries and deaths in the mines. Let us take a look at the hazards in coal mining and the accident record. COAL MINE SAFETY TODAY Underground coal mining creates underground open areas, rooms, and haulageways. The roof (top) and ribs (sides) become highly stressed, and because coal and slate are very weak in tension or compression they frequently fail and fall from the roof and ribs unexpectedly. This is the most hazardous condition miners must cope with underground, and it has consistently produced the greatest number of fatal injuries in the coal mining industry. Only very sophisticated equipment, but which is not yet practical for use underground, is able to detect the buildup of stresses that may eventually lead to a roof or rib fall. Today&apos;s miner still looks for fresh cracks in the roof or rib, listens for the "drummy" sound, and feels vibrations from loose material in the roof, when tapped with a sounding stick, in order to find material which may fall. Once located, it is barred down, but if this is not possible, it is then secured to prevent it from falling. The next great& hazard is the equipment used to mine or haul coal. It is large, heavy, reacts quickly to its controls and is operated in con- fined areas with low lighting levels. The record of the last few years shows that fatalities attributable to mining and hauling equipment are about equally divided. Thorough training as part of a complete safety program is necessary to teach employees the hazards of loose roof, rib, and machine operation in order that they can work in the safest way possible. Unless there is such a program, the trade is learned by trial and error with a resulting tragic.

Jan 1, 1973

By H. J. Gluiskoter

The chlorine content of the coals in the Illinois Basin ranges from 0.00% to more than 0.60%. The chlorine content of the Herrin (No. 6) Coal has been mapped on a regional scale and, in general, increases with the depth of the coal. The depth-chlorine correlation exists because the coal is in apparent equilibrium with the composition of the ground water associated with it, and the salinity of the ground water generally increases with depth. At least part of the chlorine can be easily removed from the coal in the laboratory. In a natural weathering experiment, chlorine values decreased markedly during an 8-week period. Results to date indicate that none of the coals studied has a sufficiently high chlorine content to make it unusable in high-temperature steam boilers, although special steps may be necessary in the preparation or utilization of some of the highest chlorine coals. Investigations into the occurrence and distribution of chlorine in Illinois coals have been in progress at the Illinois State Geological Survey for over 35 years. Since 1948, chlorine analyses of face channel samples and of drill core samples of coal have been made routinely. The increased interest in chlorine and alkalies in coal in the U.S. followed that in Europe, where power plants during World War II were called upon to produce at higher levels than previously and with less down time for maintenance. Higher steam temperatures were reached, resulting in increases in the amount of fouling of external heating surfaces and in corrosion of boiler tubes when high chlorine coals were used. Early studies of the problem showed that coals with high chlorine content were more likely than those low in chlorine to cause difficulties in installations fired with powdered fuel. Crossleyl reported that the first rule of thumb developed for British coals was that coals considered to be high in chlorine (more than 0.30%) caused the most trouble, those intermediate in chlorine content (0.15% to 0.30%) were less likely to cause difficulties and those low in chlorine (less than 0.15%) generally were not associated with alkali bonded deposits and corrosion. However, this relatively simple picture was not adequate to characterize the difficulties that could be expected during the utilization of a large number of coals and Crossley1 developed another scheme for assessing the chances of superheater corrosion. This scheme took into consideration the observation that coals high in sulfur as well as chlorine are more likely to cause corrosion and fouling than coals low in sulfur and high in chlorine. Crossley also considered the ash content. When two coals had the same chlorine and sulfur contents, the one with the greater amount of ash would be the less likely to cause difficulties. Knowing only the amount of chlorine in a coal obviously will not give all the answers. Indeed, the significance of the chlorine content has been much discussed and it has been suggested that perhaps the total alkalies are a better indicator of possible troubles. The observation that the deposits that form

Jan 1, 1968

By Gloyd M. Wilkes

The eastern section of the Park City district is drained to an elevation of 6300 ft, by means of the Ontario drain tunnel owned and maintained by Park Utah Consolidated Mines Co. This elevation represents a depth of 920 ft, in Park City Consolidated Mines Company&apos;s property. When development below the 900-ft. level was commenced, sinking was attempted through an incline winze in the fissure. The intensely fractured quartzite forming the walls of the vein could not be held after water was encountered, so it was decided that further sinking should be done in a vertical winze far enough in the foot-wall to be in the more solid quartzite outside the fractured zone containing the vein. Progress was good until a depth of 200 ft. below water table was reached, where the flow of water became serious. Sinking progressed 300 ft., to the 1200-ft. level, and there approximately 750 gal. of water per minute was being pumped. The last 20 ft. of sinking cost more than $200 per foot direct charges, whereas the over-all cost for the 300 ft. was $100 per foot. This high last cost was caused by excessive lost time in pumping. Crosscutting to the vein disclosed the fact that the 1050-ft. level had been developed only after drainage had been effected from the 1200-ft. level, but that the 1200-ft. level could not be opened because of the great amount of water encountered when the fractured zone was intersected. The ground in the fractured zone is so finely crushed that it precludes any possibility of economic support when it is wet. Furthermore, mining costs were found to be prohibitive after caving of vein walls had taken place as a result of an attempt to drive drifts before complete drainage had been effected. More than 3000 gal. per minute was pumped from the 1200-ft. level and the water table remained 75 ft. above this plane even after five crosscuts were driven to the fractured zone at 50-ft. intervals along the strike of the fissure from a footwall drainage drift. It was evident, therefore, that complete drainage must be effected before the fractured zone could be opened in any future development. After extensive investigations in this connection, a well-drilling campaign was decided upon to effect drainage of the fissure in advance of sinking and level development, so that all mining operations would be carried on in dry ground. Drilling Procedure A crosscut was driven through the hanging wall of the fissure on the 1050-ft. level, which was the deepest dry level at the time, to a predetermined location from which a vertical hole should reach the fractured zone at about 400 ft. below this level. A drill station was made and a raise was driven over the location for the hole, to act in lieu of a derrick or drill tower. This raise

Jan 1, 1943

By Gloyd M. Wilkes

The eastern section of the Park City district is drained to an elevation of 6300 ft, by means of the Ontario drain tunnel owned and maintained by Park Utah Consolidated Mines Co. This elevation represents a depth of 920 ft, in Park City Consolidated Mines Company&apos;s property. When development below the 900-ft. level was commenced, sinking was attempted through an incline winze in the fissure. The intensely fractured quartzite forming the walls of the vein could not be held after water was encountered, so it was decided that further sinking should be done in a vertical winze far enough in the foot-wall to be in the more solid quartzite outside the fractured zone containing the vein. Progress was good until a depth of 200 ft. below water table was reached, where the flow of water became serious. Sinking progressed 300 ft., to the 1200-ft. level, and there approximately 750 gal. of water per minute was being pumped. The last 20 ft. of sinking cost more than $200 per foot direct charges, whereas the over-all cost for the 300 ft. was $100 per foot. This high last cost was caused by excessive lost time in pumping. Crosscutting to the vein disclosed the fact that the 1050-ft. level had been developed only after drainage had been effected from the 1200-ft. level, but that the 1200-ft. level could not be opened because of the great amount of water encountered when the fractured zone was intersected. The ground in the fractured zone is so finely crushed that it precludes any possibility of economic support when it is wet. Furthermore, mining costs were found to be prohibitive after caving of vein walls had taken place as a result of an attempt to drive drifts before complete drainage had been effected. More than 3000 gal. per minute was pumped from the 1200-ft. level and the water table remained 75 ft. above this plane even after five crosscuts were driven to the fractured zone at 50-ft. intervals along the strike of the fissure from a footwall drainage drift. It was evident, therefore, that complete drainage must be effected before the fractured zone could be opened in any future development. After extensive investigations in this connection, a well-drilling campaign was decided upon to effect drainage of the fissure in advance of sinking and level development, so that all mining operations would be carried on in dry ground. Drilling Procedure A crosscut was driven through the hanging wall of the fissure on the 1050-ft. level, which was the deepest dry level at the time, to a predetermined location from which a vertical hole should reach the fractured zone at about 400 ft. below this level. A drill station was made and a raise was driven over the location for the hole, to act in lieu of a derrick or drill tower. This raise

Jan 1, 1943

By William G. Kegel

Apart from a usable product and good mining conditions, the greatest asset for a profitable coal mining organization is an effective mine maintenance program. The first step in achieving this is to have good mechanics-or men who want to be mechanics and are interested in knowing ,more about the design and control of the machines in their charge. A good mechanic&apos;s knowledge and ability result from ambition, curiosity, and determination. Starting with these qualities, the aspiring mechanic can launch his career by learning all he can about mechanics, electricity, and hydraulics. Though the path is rough, the end result is rewarding. Mining machinery probably receives as much, if not more, abuse as any other heavy equipment in use today. Considering the conditions under which much of the repair work must be done, it is essential that the mine operator has the best men and tools to perform the work. Mining machines, from their inception, have utilized the electric motor ; and down through the years of mechanization, this power source has undergone many changes to better adapt it to the job. The first motors used were direct-current (d-c) motors since d-c power was the most economical power source for mining at the time of early mechanization. These motors were large open-type machines which are seldom used in modern mining. Because of the mine environment, the d-c motor has been reduced in size to better suit the application in mining machines and is now manufactured with dust-tight or explosion-proof enclosures. The d-c motor is constructed with either (or both) series and shunt fields located on the stationary part of the motor (stator) and an armature coil wound on the rotating part of the motor (rotor). Power is supplied to the armature by brushes which are held stationary and make sliding contact with the armature. The brushes requires regular and careful maintenance because worn or defective brushes will cause heat or arcing which can destroy the motor. D-c motors can be used as d-c generators when mechanical power is supplied to them by the rotating

Jan 1, 1981

By A. M. Gaudin

IN flotation lime is used to depress pyrite. For this purpose it is preferred to caustic soda. The low cost of lime and the widespread availability largely account for this preference. However, there is some evidence1 that pyrite is more readily depressed by calcium than by sodium ions at the same pH. To measure the difference in adsorption of calcium and sodium, which is thought to lie at the basis of the differences in depressing action, radionuclides of

Jan 2, 1953

By P. R. Kalischer

IN the production of alloys by powder metallurgical processes it is often necessary or desirable to include one or more components that tend to form very stable oxides Included in this group of metals are aluminum, manganese, magnesium, silicon, and a few others In many cases it is not necessary for the sintered compact to have full density and the other physical characteristics of a cast alloy and in that event no undue precautions need be taken If, however, it s required that the sintered part be entirely homogeneous, and have maximum density and physical properties, some method must be found to reduce the surface films of oxide, which are always present on the metals, and for the metals mentioned above this is always extremely difficult, if not impossible Since the production of high-density alloys is of particular interest to powder metallurgists, some experiments were undertaken to devise methods of reducing the refractory oxides For this work, alloys of iron, nickel, and aluminum were chosen because aluminum oxide is one of the most stable oxides and because these alloys in the right compositions form excellent permanent magnets All of the pertinent properties of the magnets could be accurately and delicately measured by density measurements and magnetic tests of sufficient scope to give a complete demagnetization curve From such a curve the maximum coercive force, residual magnetism, and energy products could be obtained and compared with the same properties for a cast material Any lack of homogeneity, density, or solid diffusion would be immediately apparent as a decrease in the magnetic properties NATURE AND REMOVAL OF SURFACE BARRIERS The early work of the present investigation was based upon published processes In the published information it was claimed that by intimately mixing iron, nickel, and iron-aluminum alloy (50 per cent Fe, 50 per cent Al) powders, compressing such a mixture into the desired shape and size, and then sintering (heating to a temperature below the melting point of the component metals) in hydrogen at 1200ºC or higher, a sound, homogeneous article could be made having the desired physical size, shape, and strength, and good magnetic characteristics However, this early work showed clearly that something in the powder compress was inhibiting diffusion and the process was almost entirely unworkable In the initial phase of the investigation samples of iron powder, nickel powder, and iron-aluminum alloy powder were pressed into separate bars and sintered in hydrogen Both the iron and nickel powders sintered

Jan 1, 1941

By E. S. Bumps, W. F. Craig, M. Baeyertz

Metallurgists have looked at fractures macroscopically for many years and have evolved a vocabulary in which such words as "cleavage," "brittle," "shear," "ductile," "granular," "fibrous," and "silky" are used to describe the appearance of the fractured surface; but the meaning of these words in terms of metal structure is not well established. Observations of the structural meaning of "brittle" and "ductile" fractures in plate steels have been made, notably, by Kramer and coworkers1 and by Tipper.2 Grossman3 has studied the fracture of tempered martensite and combinations of ferrite and martensite. Notwithstanding these and other less concerted attacks on the problem, present understanding of fracture rests more on assumptions and logic than on experiment. It is the purpose of this paper to add a little to the growing fund of experimental observations of the nature of fractures in steel. The particular fractures to be described were obtained in conventional impact testing of an ordinary structural steel shape. In impact tests of the Charpy type, the specimens fail in a characteristic manner that depends on the steel and the temperature of testing. With ordinary structural and many other steel products, an appropriate range of testing temperature will cause a considerable change in the energy absorbed before fracture. This change is known as the energy transition and is accompanied, more or less closely, by alteration in the appearance of the fracture. At testing temperatures below the transition, the terms "brittle," "cleavage," or "granular" are used to describe the fracture; above it, "ductile" or "shear" are often used. Within the transition, the fracture changes from "brittle" to "ductile" by a progression in appearance, wherein the "brittle" portion of the fracture becomes restricted to a smaller and smaller central area of the fracture, as the testing temperature is raised and the "ductile" type of fracture is approached. All this is well known to metallurgists. The specimens under consideration are of the conventional V-notch Charpy type. They were taken from a structural steel shape of the following analysis: C Mn P S Si 0.17 0.46 0.009 0.029 0.03 Both longitudinal and transverse specimens were tested and examined. Fig 1 shows the energy values plotted against testing temperatures in the usual way. The curves for both longitudinal and transverse specimens show an energy transition, although the maximum energy absorbed at testing temperatures above the transition is greater in the case of the longitudinal specimens. Fig 2 illustrates the changes in the macroscopic appearance of the fractures that are associated with the energy transitions shown in Fig 1. Macrographs of the fractured surfaces of the specimens have been identified with the fracture ratings at intervals on each fracture curve. The numerical fracture rating on the ordinate of Fig 2 indicates the percentage of the area of each fracture that was considered to be "brittle" on macroscopic observation. Such rating of the fracture type in impact tests is now customary in many laboratories. Hereafter the specimens will be identified by reference to Fig 2 as 90 pct "brittle," 80 pct "brittle," and so on, in accordance with this macroscopic evaluation of the appearance of the fractured surface. The discussion of the fractures is divided into three parts. The first two are concerned with the mode of fracture and its relation to general structural features. As the same metal-lographic features occur in both longi-

Jan 1, 1950

By Ingvar Janelid

DURING the last ten years, in the effort to save manpower and costs, methods of drilling and blasting in Sweden have changed and developed in a revolutionary manner. These developments have been accompanied by extensive alterations in methods of tunneling and in mining technique. Since the end of the 1940&apos;s there has been a 100 pct change-over in Sweden to the use of tungsten carbide tipped drill steel. Both investigations and practical results have shown clearly that a tungsten carbide chisel bit fastened directly on the drill steel is the most economical for Swedish conditions. This applies to drill steel up to the longest size it is practical to handle. In terms of drilling footage, durability of the drill steel and the tungsten carbide bit is generally the same. In this respect, therefore, a detachable bit offers no advantage over integral steel. Transportation of integral steel to the grinding plant, instead of detachable bits only, involves heavier work, but this is counteracted by placing grinding plants closer together or by grinding at the working place itself. The drilling rate with integral steel is higher, the trouble of changing bits is avoided, and the difficulties which always arise with joints are eliminated.

Jan 6, 1954

By H. L. Riley, B. W. Gandrud

As far as the present writers know, this system of flotation has not been used elsewhere in this country, but in the last couple of years it has been introduced, with minor variations, at one plant in England and one in Wales. The system has been described and discussed in a number of publications. The following is quoted from an abstract of the latest of these," a paper presented at an International Conference on Industrial Combustion in 1952. On the basis of experience to date with the commercial plants, it is believed that the kerosene-flotation process incorporates all the necessary elements to make it greatly superior to anything else now available for treating of fines in wet processes of coal preparation. Additional study and investigation are still needed, however, to determine if certain phases of the process can be improved to such an extent as to make it generally satisfactory and acceptable to the industry. Further improvements will be needed with respect to the capacities of the flotation cells and the reagent consumption.

Nov 1, 1955

By W. H. Furlonge

WHILE fulfilling professional engagements, my travels over this portion of the Transvaal have been quite extensive—always on horseback however, so that anything like a thorough investigation of the ground passed over has been necessarily impossible; still, the more minute examination of certain small areas, coupled with general observations, has enabled me to form some idea as to the prominent geological features of the country as a whole. Anything like a complete or comprehensive description is indeed out of the question, as there are no proper maps of the country and the facilities for observation are limited. A large plateau, called the "High Veldt," stretches from east to west across the Transvaal. It is generally level, or gently rolling, and has an average elevation of 6000 feet above the sea; it is destitute of timber, and in fact greatly resembles the western prairies of North America. Rock-outcrops are not common in it. It terminates very abruptly to the east and northeast, the descent of 2000 or 3000 feet into the mountainous country that occupies its borders being made in a

Jan 1, 1890

By Daniel R. Hull

In 1926 Gendersl reviewed the existing theories of this subject and stated his views in support of the gas-pressure theory. Again, in 1937, the subject was thoroughly reviewed by N. B. Vaughan3 and by Phillips and Brick,2 so that no résumé is called for here. The purpose of this paper is to describe certain observations made in the course of mill work, and to point out that they mostly tend to confirm the gas theory of Genders. Vapor Segregation There is, however, one type of inverse segregation that can be accounted for by considering the volatility of one of the constituents of an alloy. The most familiar case is ordinary brass, which is subject to a zinc enrichment of a few tenths of a per cent at the surface of a chill casting. This has been noted in 70-30 brass by Genders, and a typical example of it is given in Table 1, which represents a cylindrical billet 7 in. in diameter by 55 in. long. After lathe-turning 1/32 in. from the surface, the remaining distance to the center was sampled at six equally spaced intervals. the lead, which is essentially the same throughout, will be mentioned later. Consider a brass-mill mold, either round or rectangular in cross section, standing several feet high. It may require a minute or two for pouring. Before it is full, the metal in the lower end has partly solidified and contracted somewhat away from the mold. The initial shell of solidification follows not far behind the top of the column, even if the central portion is liquid for a long way down. There is, then, a space between metal and mold that is filled with zinc vapor. The vapor has no exit, because the liquid at the top of the rising column is not only in contact with the mold but keeps UP a fresh supply of zinc vapor, which has, perhaps, already begun to condense in the lower portion. The cycle is short. Within a minute or two after the mold is full the bar has cooled enough to condense all the zinc. Some of it may condense on the mold; it might be expected that most of it would condense there, but the mold at that time is well coated with a velvety carbon residue from the oil dressing, overlain by fluffy zinc oxide that commenced covering the inside of the mold as soon as pouring began. The clean skin of the freshly cast brass offers a preferred surface for condensation. Reabsorption is quick and inevitable. A simple experiment indicates that a surprisingly large quantity of zinc vapor is trapped in the space between mold and

Jan 1, 1941

By Daniel R. Hull

In 1926 Gendersl reviewed the existing theories of this subject and stated his views in support of the gas-pressure theory. Again, in 1937, the subject was thoroughly reviewed by N. B. Vaughan3 and by Phillips and Brick,2 so that no résumé is called for here. The purpose of this paper is to describe certain observations made in the course of mill work, and to point out that they mostly tend to confirm the gas theory of Genders. Vapor Segregation There is, however, one type of inverse segregation that can be accounted for by considering the volatility of one of the constituents of an alloy. The most familiar case is ordinary brass, which is subject to a zinc enrichment of a few tenths of a per cent at the surface of a chill casting. This has been noted in 70-30 brass by Genders, and a typical example of it is given in Table 1, which represents a cylindrical billet 7 in. in diameter by 55 in. long. After lathe-turning 1/32 in. from the surface, the remaining distance to the center was sampled at six equally spaced intervals. the lead, which is essentially the same throughout, will be mentioned later. Consider a brass-mill mold, either round or rectangular in cross section, standing several feet high. It may require a minute or two for pouring. Before it is full, the metal in the lower end has partly solidified and contracted somewhat away from the mold. The initial shell of solidification follows not far behind the top of the column, even if the central portion is liquid for a long way down. There is, then, a space between metal and mold that is filled with zinc vapor. The vapor has no exit, because the liquid at the top of the rising column is not only in contact with the mold but keeps UP a fresh supply of zinc vapor, which has, perhaps, already begun to condense in the lower portion. The cycle is short. Within a minute or two after the mold is full the bar has cooled enough to condense all the zinc. Some of it may condense on the mold; it might be expected that most of it would condense there, but the mold at that time is well coated with a velvety carbon residue from the oil dressing, overlain by fluffy zinc oxide that commenced covering the inside of the mold as soon as pouring began. The clean skin of the freshly cast brass offers a preferred surface for condensation. Reabsorption is quick and inevitable. A simple experiment indicates that a surprisingly large quantity of zinc vapor is trapped in the space between mold and

Jan 1, 1941

By William E. Ford, Edward Salisbury Dana

This section includes one distinct group, the Stibnite Group, to which orpiment is related; the other species included stand alone. Pyr., etc. - In the closed tube melts and gives a dark red liquid when hot and a red- dish yellow solid when cold; in the open tube (if heated ver slow? ) sulphurous fumes, and a white crystalline sublimate of arsenic trioxide. B.B. on ciarcoaTburm with a blue Hame, emitting arsenical and sulphurous odors. Soluble in caustic alkalies. Artif. - Realgar is frequently noted as a sublimation product from furnaces roasting ores of arsenic. Crystals are produced when arsenic sulphide is heated in a sealed tube with a solution of sodium bicarbonate. Obs. - Realgar occurs usually in veins associated with silver and lead ores. It has been found in volcanic regions as a sublimation~duct. It has also been noted as a deposit from hot spring waters. It is often rtasociate wlth orplment. It occurs at Felsi5bBnya, Kapnik and NagyAg, Hungary; Allchar, Macedonia. Binnental, Switzerland, in dolomite. In the United States, at Mercur, Utah; in the Norris Geyser Basin, Yellowstone Park, as a deposition from the hot waters. Found at the Monte Cristo millin district, Snohomish Co., Washington: the namerealga7 is from the Arabic, Rahj af gh&r,powder of the mine. Use. - Was used in fireworks to give a brilliant white light when mixed with saltpeter and ignited. The artificial material is now used for this purpose.

Jan 1, 1922

By J. M. McDowell

A study has been made to deter~r~irre how the behavior of a water drivee reservoir changes as a function of the permeability of the formation and as a function of the size of the aquifer. The effect of pressure maintenance programs on the rote of nat11rn1 water influx is also studied, (IS well as the influence on the influx of the position of water injection we1ls with reference to the oil-water contact. The results are determined by the use of an electrical reservoir analyzer and are plotted as families of curves of pressure, natural water influx, and water injection vs time or cumulalive production. Two size aquifers are studided. One is limited with a 36-inile radius, and the, other approximates an infinite reservoir. The field remains the same in all respects for the completed. study except that the permeability is changed to agree with that assumed for the aquifer. 1 N TR ODUCTI ON this study was undertaken in -dcr to determine how the pres- sure decline and water influx of a water drive field would change as a function of the rate of fluid withdrawals, as a function of the permeability of the formation, and as a function of the size of the aquifer. The effect of pressure maintenance programs on the rate of natural water influx was also studied as was the position of water injection wells with reference to the oil-water contact. The information has been determined by the use of an electrical reservoir analyzer1, sometimes referred to as a Carter type analyzer. This instrument is an analog type computer which can be set up to represent a water-drive oil field. It can reproduce the past performance of the field in terms of analogous electrical quantities when the proper circuit analog of resistors and condensers has been determined, also, it can determine the future behavior for any method of production which may be selected, or permit the comparison among several different methods. Although most applications of the reservoir analyzer"" have been to thc study of specific field performance, it is intended to use the analyzer here to help understand how various reservoir characteristics effect the final performance of the field and to sec under what conditions water injection will be of benefit and to what extent. Within the oil industry the performance of water-drive reservoirs was first described analytically by LV. Hurst&apos; and M. Muskat2 for certain types of boundary conditions. The solutions of the equations developed involved products of exponential functions and Bessel functions. Later publications by Hurst4 and van Ever-clingen" and the hooks of Muskat6 gave further information on reservoirs with other boundary conditions. They also presented rather extensive curves and tables to help evaluate the analytical expressions involved. A rccent series of publications by Chatas. bascd on the work of Hurst and van Everdingen, gives quite complete charts and tables of data to evaluate the pressure decline or water influx in infinite or limited radial reservoirs. and in linear reservoirs. The curves in all of these publications are given in dimensionless form

Jan 1, 1956