Search Documents

By H. E. Gross

A plausrsle method of drilling beyond the continental shelves is set forth with limitations of the method. The continental shelves comprise the water-covered portions of land masses out to 600 ft. of water, or roo fathoms. The problems and possibilities of drilling beyond this depth are discussed in this paper. Introduction Much attention is being given the problem of developing petroleum beneath the open sea. Geophysical surveys have been made 26 miles offshore1 from the continental United States, and onco offshore ownership is established it is likely that there will be drilling for oil on the continental shelves. More than two years ago the author presented the means for drilling in deep water.2 at the fall meeting of the Petroleum Division of the AIME at Los Angeles. His concepts then were based on the use of rigid foundations suitable for drilling in water up to 600 ft. deep. The present paper suggests a method for drilling in deeper water. Possibilities and Problems of Drilling beyond the continental shelves It being conceded that because restricted deep-water portions of the hydrosphere might contain oil in commercial quantities, and that at any rate it is pertinent to know more of the nature of the lithosphere beneath the hydrosphere, the possibilities and problems of drilling beyond the continental shelves should be set forth. Drilling in open water would offer few if any advantages over drilling on land. These are: 1. The ocean transportation is available to deep-water drilling sites, and extensive pipe lines and roads are unnecessary. 2. Refinery facilities and markets perhaps are established on the near-by shore where adjacent fields on land are nearing depletion. 3. There is freedom from jungle pests and tropical diseases. 4. Competitive drilling is less likely. 5. Extensive areas attractive for development arc not yet under lease or concession. Disadvantages are great and numerous: 1. Storm hazards from wind and wave. 2. Expensive foundations, either rigid or floating. 3. Shutdown times because of weather. 4. Marine Regulations of Federal Bureaus in addition to customary regulations on land. 5. Frequent difficulty in moving men and materials to and from drilling platforms. 6. Extra precautions required in open sea. For drilling in water more than 500 or 600 ft. deep, rigid foundations2 become too costly, and floating foundations must be used, and they must meet the following requirements:

Jan 1, 1947

YEAR OF ELECTION 1913. FRANK DAWSON ADAMS, Montreal, Canada. 1922. FEDERICO GIOLITTI Torino, Italy. 1921. FRANK WILLIAM HARBORD London, England. 1917. HERBERT HOOVER Washington, D. C. 1941. DANIEL COWAN JACKLING San Francisco, Calif. 1939. HENRY KRUMB New York, N. Y. 1921. C. McDERMID London, England. 1913. EZEQUIEL ORDONEZ Mexico City, Mexico. 1935. ROBERT PEELE New York, N. Y. 1938. A.M. PORTEVIN Paris France 1937. JOHN V.W. REYNDERS, New York, N. Y. 1937. GEORGE S. RICE Washington, D. C. 1911. ROBERT H. RICHARDS Cambridge, Mass. 1934. T.A. RICKARD Victoria, B.C., Canada

Jan 1, 1942

THOMAS T. READ, Palmerton, Pa. (communication to the Secretary*). -It is much to he regretted that in presenting a further discussion of these deposits, first described by myself' and later discussed by C. M. Weld,2 Mr. Wang bas not made a more complete presentation of the evidence on which he bases his conclusions as to their origin. Mr. Weld said in his paper that his visit was confined to a few hours, that he saw only one of the several exposures, and that he took away no samples for further study. My own visit was brief, and for another purpose than the study of the geological features of 'the deposits, so the fact that Mr. Weld described as a hornblende-granite the rock which I described as a "dark gray syenitic rock," and which Mr. Wang identifies as a hornblende-syenite, seems of no great importance, since this rock is generally decomposed along the contact, presumably the only place in which Mr. Weld observed it. Later in the same paper (p. 31), Mr. Weld says that his opinion is that the magnetite of the deposits is primary, but Mr. Wang makes no mention of this in stating his own conclusion to the same effect. When Mr. Weld's paper appeared, I did not discuss it, because, although I considered the evidence- that he brought forward to support his belief that the magnetite is primary too slender to support the hypothesis, my own evidence to the contrary was equally tenuous. .The opportunities for observation and study open to Mr. Wang must have provided him with

Jan 6, 1917

By Charles Jackson Abrams

MINING is one of the major industries of the Rocky Mountain region and since the United States became involved in the present World War, all mines have been called upon by the Government for the maximum production of the strategic metals necessary. Operating under the most adverse conditions, such as priority requirements, slow delivery of necessary material and equipment, labor shortages, and freezing of all wages, which still permitted some industries to pay higher rates than were allowable in the mines, thereby drawing labor from the mines; and the United States Employment Service continually giving mine labor certificates of availability; these and many other problems made mine operation particularly difficult. Yet, in spite of these obstacles, the mining industry, either through its own resources or through Government subsidies in the form of loans or premium prices for strategic metal, have and still are making an all-out effort to meet Government demands. They, without question, have played a major role in assisting the war effort.

Jan 1, 1945

PRESIDENT OF THE COUNCIL ROBERT W. HUNT CHICAGO, ILL. (Term expires February, 1907 ) VICE-PRESIDENTS OF THE COUNCIL WILLIAM P. BLAKE TUCSON, ARIL. THOMAS F COLE DULUTH, MINN. IRVING A. STEARNS WLKES-BARRE, PA. (Term expires February, 1907 ) HENRY M HOWE NEW YORK, N. Y. J. B GRANT DENVER, COLO. JAMES D HAGUE NEW YORK, N. Y. (Term expires February, 1909 )

Jan 1, 1910

By J. Hall Carpenter, James E. Lawver

Shortly after the passage of the Taconite Amendment in Minnesota, several mining companies announced their intention to build new magnetite taconite plants and another announced its intention to augment present facilities. It is clear that Minnesota will enjoy an expanding magnetite taconite industry, but despite the fact that the reserves are large, eventually they will have to be supplemented by oxidized deposits. Furthermore, not all producers have magnetite taconite reserves. Due to the extensive oxidation of most of the western part of the Mesabi Range, there are no large blocks of unaltered magnetite taconite that lend themselves to open pit operations. Unless a commercial process can be developed to concentrate the oxidized, or so- called "nonmagnetic", taconite and semi-taconite, the existing mines operating in the western part of the range will be forced to shut down when the direct shipping, wash and gravity ores are depleted, or are no longer salable, because of their poor quality compared to high-grade pellets. KNOWN PROCESSES COSTLY The enormous reserves of the oxidized iron- bearing formation have offered a tantalizing challenge to metallurgists for many years. In fact, several processes for concentrating certain types of oxidized ore have been successful at both laboratory and pilot plant level, but to date no process for concentrating semitaconite or oxidized taconite has reached commercial fruition. Magnetic roasting, followed by low-intensity magnetic separation1, has shown considerable promise because the high iron recovery makes the ratio of concentration of many of the oxidized ores more favorable than that of magnetite taconite. However, the capital and operating costs are high and, in many cases, a high- grade concentrate cannot be made without resorting to flotation of the magnetic concentrate. Hence, most research groups are investigating alternate methods of concentration with the hopes of reducing the cost.

Jan 9, 1965

By T. Sterry Hunt

Coal was mined to a small extent near Tuscaloosa, in Alabama, and even carried by boats to Mobile, half a century since. Professor Porter, and later, Professor R. T. Brumby, occupied themselves with the geology of the region, and it attracted the attention of Sir Charles Lyell, who visited the region. It is, however, to the two reports of Professor Tuomey, geologist to the State, published in 1850 and 1858, that we owe our first clear notions of the geology of the Alabama coal-fields. His work has, since 1873, been continued by Professor Eugene A. Smith, of the University of Alabama, whose valuable reports, extending and completing the work of his predecessor, are indispensable guides to the geological inquirer in this region. Mention should also be made of the investigations of Mr. R. P. Roth well, who, after three years of studies in parts of the Alabama coal-fields, read before the American Institute of Mining Engineers, in October, 1873," a brief but important paper calling attention to the great deposits of coal and iron-ore found therein, and to their economic importance. Having myself, during the past year, had an opportunity of visiting parts of this region, I have thought that it might be well to bring before the Institute some facts and considerations as to its geological and geographical characteristics, and the value of its mineral resources. It is well known that the great Appalachian coal-basin, stretching southwestward through western Tennessee and the northwestern corner of Georgia, terminates in northern Alabama in what is called the Warrior coal-field, which there covers an area of about 5000 square miles. Lying along the southeast border of this, but

Jan 1, 1883

By Victor Lenher

The interest shown recently in selenium and tellurium has brought many requests for an assembling of the analytical chemistry of these two elements. The intention of this paper is to discuss all of the chemical principles utilized in the detection and quantitative determination of these elements, as well as to describe the works methods actually followed by producers of tellurium and selenium in the United States. These methods have been furnished by S. Skowronski of the Raritan Copper Works, H. D. Greenwood of the United States Metals Refining Co., F. F. Colcord of the U. S. S. Lead Refinery, and E. W. Rouse and A. E. Hall of the American Smelting and Refining Company. Occurrence Selenium is found associated with sulfur, to which in many respects it is quite similar. Occasionally deposits of native sulfur, notably those in the Lipari Islands, Kilauea, and Japan, show a red-brown coloration, I which is readily distinguished from that of other sulfur; this red-brown * sulfur contains a small amount of selenium. Not infrequently, the , sulfides of the heavy metals are accompanied by selenium and tellurium, • presumably as selenides and tellurides. The Scandinavian pyrite, which is one of the large sources of European sulfuric acid, when roasted has fur- - nished a large part of the selenium that has come to the United States; it I was in flue dust from the roasting of Scandinavian pyrites that the element was discovered by Berzelius in 1817. Greek and Spanish pyrites also

Jan 1, 1923

By Victor Lenher

The interest shown recently in selenium and tellurium has brought many requests for an assembling of the analytical chemistry of these two elements. The intention of this paper is to discuss all of the chemical principles utilized in the detection and quantitative determination of these elements, as well as to describe the works methods actually followed by producers of tellurium and selenium in the United States. These methods have been furnished by S. Skowronski of the Raritan Copper Works, H. D. Greenwood of the United States Metals Refining Co., F. F. Colcord of the U. S. S. Lead Refinery, and E. W. Rouse and A. E. Hall of the American Smelting and Refining Company. Occurrence Selenium is found associated with sulfur, to which in many respects it is quite similar. Occasionally deposits of native sulfur, notably those in the Lipari Islands, Kilauea, and Japan, show a red-brown coloration, I which is readily distinguished from that of other sulfur; this red-brown * sulfur contains a small amount of selenium. Not infrequently, the , sulfides of the heavy metals are accompanied by selenium and tellurium, • presumably as selenides and tellurides. The Scandinavian pyrite, which is one of the large sources of European sulfuric acid, when roasted has fur- - nished a large part of the selenium that has come to the United States; it I was in flue dust from the roasting of Scandinavian pyrites that the element was discovered by Berzelius in 1817. Greek and Spanish pyrites also

Jan 1, 1923

By Thomas L. Kesler

Essentially all of the barite produced in Georgia has come from the Cartersville district in the northwest part of the state. The earliest recorded shipment of ore, 60 tons, was made in 1894.1 With the exception of the four-year period 1931 to 1934, the separate yearly output has been recorded and published since 1915, whereas the total yearly output of the United States has been published since 1880. The separately recorded production of Georgia (Cartersville) through 1947 is 2,232,544 short tons valued at $14,900,746,2 but unpublished data on the period 1931 to 1934, plus the estimated unrecorded output prior to 1915, make the actual total about 2,400,000 short tons. This is about 21 pct of the total production of the United States, which, through 1947, is 11,328,440 short tons valued at $71,683,386.2

Jan 1, 1949

By Richard Rothwell

At the last meeting of the Institute, Mr. Per Larsson read a very interesting paper on the Chapin mine of Michigan, in which he described the systems of mining that had, at different times, been tried in that great ore-body, and especially the system now in use, which consists in working the ore out from the bottom upward in lifts. Shortly after that paper was written, but before it had been published, or that I had had an opportunity of reading it, I bad the pleasure of visiting the mine. At that time I was making a profes sional examination of a nnmber of the mines on theGogebic Range, and others in the Menominee region, Michigan and Wisconsin, and had occasion then, as during several previous visits, to study closely the methods and cost of mining in these districts. As the outcome of these investigations, it appeared evident to me that the system of working on the chamber-and-pillar plan, which up to that time had been the only method of underground work adopted in the Gogebic

Jan 1, 1888

By Ralph Hultgren, David W. Mitchell

MAGNESIUM alloys usually are superheated before casting in order to ensure fineness of grain. Superheat temperatures in common use range from 1600° to 1700°F while the casting temperature, which depends upon the mold shape, is usually 200° to 300°F lower. The process of superheating requires considerable time and seriously shortens the life of the iron pots used. Recently it has been reported' that if acetylene, carbon dioxide or natural gas is bubbled through molten electrolytic A.S.T.M. No. 4 alloy at 1400°F. for 5 min., grain refinement equivalent to that of superheating will take place. Addition of certain solids such as graphite or aluminum carbide accomplishes the same results.2 As will be shown in this paper, it is possible to achieve grain refinement in magnesium casting alloys at low temperatures by mechanical stirring of the molten metal for a short time. This process was developed in the course of research work, supervised by the War Metallurgy Committee under the "Restricted" Project NRC-550, for the Office of Production Research and Development of the War Production Board. This paper, based on that work, has been released for publication by the O.P.R.D. MATERIALS AND METHODS The alloys studied were the most common American sand-casting alloys designated as No. 4 and No. 17 by the American Society for Testing Materials. The magnesium used in these alloys was of both carbothermic3 and electrolytic4 origin. Chemical analyses supplied by the producers are shown in Table I. Each heat consisted of approximately 5 lb. of alloy melted in a Tercod crucible. It was refined by fluxing with Permanente No. 7* refining flux at 1300° to 1350°F. After cooling to 1200' to 1250°F., portions of approximately one pound each were ladled into iron crucibles contained in an electric furnace at about 1250°F. The molten metal was covered with Permanente No. 21† covering flux and then heated to the temperature to be investigated. Normally each of the four portions was given a different treatment. In a typical case one portion was stirred vigorously for 5 min., acetylene gas was passed through a second portion for 5 min., a third portion was superheated to 1600°F for 15 min., then cooled to casting temperature, and the fourth was held for 5 min. at the temperature of stirring or gassing without other treatment. Each portion was then cast into one-inch diameter cylinders in three "nonturbulent" molds of identical shape. One mold was made of cast iron and the other two of baked sand. The cast-iron mold and one of the baked sand molds were heated to 360°F., the other baked sand mold was at room temperature. The freezing times in these molds were

Jan 1, 1945

By Ralph Hultgren, David W. Mitchell

Magnesium alloys usually are superheated before casting in order to ensure fineness of grain. Superheat temperatures in common use range from 1600" to r 7o0°F.; the casting temperature, which depends upon the mold shape, is usually 200° to 300°F. lower. The process of superhcating requires considerable time and seriously shortens the life of the iron pots used. Recently it has been reported1 that if acetylene, carbon dioxide or natural gas is bubbled through molten electrolytic A.S.T.M. No. 4 alloy at 1400°F. for 5 min., grain refinement equivalent to that of superheating will take place. Addition of certain solids such as graphite or aluminum carbide accomplishes the same results? As will be shown in this paper, it is possible to achieve grain refinement in magnesium casting alloys at low temperatures by mechanical stirring of the molten metal for a short time. This process was developed in the course of research work, supervised by the War Metallurgy Committee under the "Restricted' project NRC-550, for the Office of Production Research and Development of the War Production Board. This paper, based on that work, has been released for publication by the O.P.R.D. Materials and Methods The alloys studied were the most common American sand-casting alloys designated as No. 4 and No. 17 by the American Society for Testing Materials. The magnesiun used in these alloys was of both carbothermic3 and electrolytic' origin. Chemical analyses supplied by the producers are shown in Table I. Each heat consisted of approximately 5 lb. of alloy melted in a Tercod crucible. It was refined by fluxing with Permanente No. 7* refining flux at 1300° to 1350°F. After cooling to 1200° to 1250°F., portions of approximately one pound each, were ladled into iron crucibles contained in an electric furnace at about 1250°F. The molten metal was covered with Permanente No. 21 † covering flux and then heated to the temperature to be investigated. Normally each of the four portions was given a different treatment. In a typical case one portion was stirred vigorously for 5 min., acetylene gas was passed through a second portion for 5 min., a third portion was superheated to 1600°F. for 15 min., then . cooled to casting temperature, and the fourth was held for 5 min. at the temperature of stirring or gassing without other treatment. Each portion was then cast into one-inch diameter cylinders in three "nonturbulent" molds of identical shape. One mold was made of cast iron and the other two of baked sand. The cast-iron mold and one of the baked sand molds were heated to 360°F., the other baked sand mold was at room temperature. The freezing times in these molds were

Jan 1, 1945

By C. W. Dunham

DESIGN of the structures for the Morenci Reduction Works involved many interesting problems. Naturally, the chief purpose of these structures is to house and support the equipment and other things necessary for or incidental to the conduct of production. hence most of the features of the design were developed to suit these particular conditions; however, several are so generally applicable as to warrant description.

Jan 1, 1942

By John F. Abel

"The most conservative persons I ever met are college undergraduates." Woodrow Wilson said that in 1905. No one is saying anything like it today. Chaos on the campus was a cliche of the sixties. Since 1905, education has expanded in every direction. Many more people are being educated for much longer periods of time. The school-leaving age has risen from 14 years to 20 years, on an average. Many are in school until after their 25th birthday. On the surface this situation appears all to the good. Our technical society needs a massive yearly infusion of semitrained (or educated, if you prefer) new blood. The efficiency of our economy and our standard of living are tied to high individual productivity which can be achieved only with an educated work force. Our democratic institutions are said to be founded on an educated electorate.

Jan 1, 1970

By Shiro Ban-ya, John Chipman

Using the same experimental method previously described, the activity of sulfur in a number of quaternary and more complex liquid iron alloys at 1550oC is determined. A "cross-product term zj.zk is determined for each of the quaternary alloys to take account of the mutual effects of the combinalion on the indi-vidual contributions to In 5 The interactiotl coefjicienls delermined for ternary solutions and cross-pvoducl coefficierlts from the quaternary systems are used to estimate the activity coefficient of sulfur in more complex alloys. OUR recent papers 1,2 have described new determinations of the activity of sulfur in Fe-S binary and Fe-S-j ternary solutions, but the practical applications of these data require the estimation of activity of sulfur in more complex systems. Previously, Sherman and chipman3 devised an approximate method for calculating the activity of sulfur in complex systems by summing the contributions to the logarithm of the activity coefficient of each element in the alloy. This procedure is more successful, as one of us has pointed out,4 when the concentration variable is taken as zs = ns/(nFe — nS t CLJ~ nj) rather than the conventional atom fraction x~ = nS/(nF, + nS + Enj). In the former definition, which is based on analogy to interstitial solutions, the value assigned to uj is normally +1 for metallic and -1 for nonmetallic elements." In addition, however, the effects of mutual interaction between alloying elements must be considered for the accurate estimation of the activity of sulfur in more complex systems. The purpose of this investigation has been to devise a more reliable method for estimating the activity coefficient of sulfur in nmIticomponent iron alloys. The measurements were carried out on some quaternary systems Fe-S-j-k for combinations of silicon, chromium, nickel, cobalt, molybdenum, and tungsten. Manganese was not included since the experimental method has been found unsatisfactory for volatile, sulfide-forming elements. The experimental method was the same in every detail as described previously. 1,2 The concentrations of sulfur, silicon, chromium, and copper in the quenched metals were determined by chemical analysis but those of nickel, cobalt, molybdenum, and tungsten were calculated from charged amounts. Iron sulfide was included in the charges in amounts estimated to furnish approximately the final sulfur content. CALCULATION W2 have shown2 that when zs and zj are the concentration variables in a ternary Fe-S-j solution the logarithm of the activity coefficient S = a~/zg is a linear function of the variables as and aj defined as follows:

Jan 1, 1970

By Jack M. Swales

Kermac Potash Co., the newest American entry in a rapidly expanding industry, has come on the scene with notable variations in conventional shaft-sinking and mining techniques. Located in the famed potash producing district east of Carlsbad, N. Mex., Kermac started up its mine in November, 1965, to supply ore to the company's 500,000-tpy potash crystallization refinery. In so doing, the company (1) drilled the first large diameter mine shaft in the potash industry and (2) has employed new continuous miners especially adapted for use in thin potash beds. REACHING THE ORE ZONE In its initial mine planning, Kermac, a partnership owned jointly by Kerr-McGee Corp. and the National Farmers Union Development Corp., considered it imperative that the shafts be sunk and equipped as soon as possible and that the mine be developed sufficiently to insure a constant ore feed to the mill when the unit was placed on stream. After examining the alternative sinking techniques available to it, the company decided to accept a proposal by Big Hole Drillers, Inc., to drill the shaft from the surface through various formations of sandstones, siltstone, shales, anhydrite, limestones, dolomite and salts to the potash ore zone.

Jan 12, 1966

Institute of Metals Division SAM TOUR, Chairman J. R. FREEMAN, JR., Vice-chairman ZAY JEFFRIES, Past-chairman C. H. MATHEWSON, Vice-chairman WILLIAM M. COHSE, Secretary-Treasurer 810 Eighteenth Street, N. W. Washington, D. C. Executive Committee Until February, 1931 Until February, 1932 Until February, 1933 T. S. FULLER J. L. CHRISTIE W. M. W.M. PEIRCE G. E. JOHNSON ARTHUR PHILLIPS A. J. PHILLIPS W. A. SCHEUCH H. M. WILLIAMS GUY C. RIDDELL Research PAUL D. MERICA, Chairman S. SKOWRONSKI Data Sheet R. S. ARCHER, Chairman T. S. FULLER J. STRADSS C. H. MATHEWSON F. L. WOLF

Jan 1, 1929

By A. C. Fraker, H. H. Stadelmaier

In the systems Mo-Fe-C, Mo-Co-C, and Mo-Ni-C the phase boumdaries of the cubic Ij carbides were determined at 1000°C and the variation of the lattice parameter with composition was measured. In the system Mo-Fe-C a single ternary carbide, Mo3Fe3C, was observed. In Mo-Co-C and Mo-Ni-C two new n phases of the type M12C were found: Mo6C06C and Mo6Ni6C. At 1000°C they coexist with the M6C phases MO3-4,CO3-2C and Mo3-4Ni3-2C, respectively. Mo3C03C and Mo4C02C are not separate phases but parts of a single M6C phase region, and the same is true of Mo3Ni3C and Mo4Ni2C. THE n carbide structure type has been known since it was determined by westgren' in 1933, yet reliable information on phase compositions of this type is ap-parently scarce. The following selection of suggested formulas illustrates the extent of the confusion con-cerning compositions: W2-3Fe4-3C,1W6Fe6C,2 W2_4Fe4-2C,3 (W,Fe)6C,4 Tj.-W4Co2C and nz-W6Co6C,5 n1-W3Co3C and n2-w4Co2C,5 W3C03C and w6Co3C2,7 MO3Fe3C,8n2-M04Fe2C,9 (MO,Fe)6C,4 MO3CO3C,8 n2-MO4CO2C.9 Many of these compositions obviously overlap, some disagree in carbon content. The use of the designations 77, and n2 is not consistent. There is uncertainty whether two carbides M6C coexist or whether there is only one M6C with a wide range of substitution of one metal for the other. The existence of M12C seems questionable altogether if one ignores the results of a neutron diffraction study of W6Fe6C supporting that particular metal to carbon ratio.'' More reliable information is available for the iso-typic oxides studied by Nevitt,11 Nevitt, Downey, and orris," and Meussner and carpenter.l3 That n car-bides and oxides are structurally identical, particularly with respect to the location of the metalloid atom, has been demonstrated clearly by Stadelmaier and Meussner14 and also by Parthe, Jeitschko, and sadagopan.15 Therefore the present paper, which attempts to establish the phase boundaries of n defini-tively for three carbon systems, has implications for the whole family of filled Ti2Ni types. EXPERIMENTAL PROCEDURE The samples were prepared in two stages. Pellets weighing 3 g were compacted from powders of the elements and presintered in a closed tube of fused silica that had been evacuated to lO-4 mm Hg. This was fol- lowed by arc melting the sintered samples under argon. Remelting the button once was sufficient to produce homogeneous specimens. The metal powders had the following minimum purities in wt pct: molybdenum 99.5, iron 99.0, cobalt 99.7, nickel 99.9, graphite 99.94. Carbon determinations by the gas volumetric method were obtained from thirty-one of the one hundred samples in the annealed condition. They were limited to compositions that were critical to placing a boundary line in the isothermal sections. The carbon losses were comparatively low and averaged less than 1.5 at. pct. For annealing, the samples were sealed in tubes of fused silica evacuated to 10-4 mm Hg. The annealing schedule was 20 hr at 1250°C followed by 150 hr at 1000" ±10°C. For the water quench the silica glass tubes were broken mechanically to speed the quench. The specimens were examined in the as-cast and annealed condition by standard metallographic techniques. Some of the as-cast and all annealed samples were studied by X-ray diffraction using a 114.6-mm powder camera with filtered Co radiation. The lattice parameters of the n phases were determined by graphic extrapolation to 8 = 90 deg on a plot against sin2 8. It is estimated that the maximum error in the lattice parameters is ±0.002A.. The phase fields were determined by the disappearing phase method, relying on X-rays for phase identification and on microscopy to detect small amounts of a phase. RESULTS Pertinent information on the binary side diagrams has been summarized by Hansen and Anderko16 and Elliott17 and will not be discussed further. Photomicrographs documenting the equilibria at 1000°C have been selected to avoid redundancy due to the similarity of the three systems. Thus there will be only one picture showing an equilibrium with Mo2C, and so forth. Molybdenum-Iron-Carbon. An isothermal section of most of the Mo-Fe-C system at 1000°C is shown in Fig. 1. No attempt has been made to distinguish between a and y iron or to determine their phase boundaries. A conspicuous absence is the phase Fe2 1Mo2C6 with the Cr23C6 structure, supporting the suggestion by Krainer4 that it decomposes by annealing at high temperatures. The only ternary phase is found in a narrow range around Mo3Fe3C (MO43Fe43C14). A microstructure with a two-phase mixture of Mo + n is seen in Fig. 2. The variation of the lattice parameter of n with the estimated composition is shown in in Table IA. The phase diagram does not agree with the results of Kuo9 who reported n2-Mo4Fe2C. Our lattice parameter Varies from 11.095A at the iron-rich end to 11.140Å at the molybdenum-richoend of the phase field whereas Kuo9reported 11.26Å for Mo4Fe2C. We are in agreement with the older work

Jan 1, 1970

By R. J. Woody

Design of the most economic continuous counter-current decantation (CCD) circuit is based on selection of the number of stages and the wash volume that will give the minimum summation of the following items: 1) Capital and operating costs of the CCD circuit. 2) Capital and operating costs of the precipitation circuit. 3) Value of the dissolved product lost.

Jan 1, 1959