Search Documents

By J. L. Sepulveda, R. F. Yap, R. Jauregui

INTRODUCTION The Third Theory of Comminution, oftentimes called the Bond Theory, was first published by Fred C. Bond in 1952. Since then, it has been widely used in the milling industry to size crushing and grinding equipment as well as to predict and evaluate their performance. Although two other comminution theories were advanced almost a century earlier, one by Rittinger, 1867, and the other by Kick, 1885, their use was limited because they did not agree with actual commercial comminution systems (Bond, 1961). According to Bond's Third Theory, the work input is proportional to the new crack tip length produced in particle breakage, and equals the work represented by the product minus that represented by the feed. For particles of similar shape, the crack tip length is equivalent to the square root of one-half the surface area, and the new crack length is proportional to [(1/vT - vF)]; where P and F are particles diameter of product and feed, respectively. For practical calculations, the particle diameter can be expressed in terms of the 80% passing sizes, P and F, respectively. Therefore, the work input is given by, [10 _ 10', W = Wi [7P_7F(1)] Where W = the energy input to the mill, (kwh/t) Wi = Work Index, (kwh/t) P = square sieve opening which 80% of the product passes, (microns) F = square sieve opening which 80% of the feed passes, (microns) Equation (1) is the mathematical statement of the Third Theory, or the Bond equation. Numerically, the work index is the energy required in kwh/t to reduce a given material from theoretically infinite feed size to 80% passing 100 microns. The work index of a particular material is determined in the laboratory by conducting the standard Bond grindability test. Bond developed separate tests for the rod mill and the ball mill. The simplified test method described in this paper, which is used at Anaconda Research Center to approximate the work index, is an alternative procedure to the ball mill

Jan 1, 1982

By W. C. Phalen

SALT-MAKING PROCESSES THE production of salt in the United States divides itself at the outset into two distinct classes: (1) The mining of rock salt and its purification and separation into marketable sizes, and (2) the production of salt by evaporation from brines, bitterns, and other solutions. The processes employed at the present time in the manufacture of salt by evaporation may be outlined as follows: 1. Solar evaporation. 2. Direct-heat evaporation (a) in open kettles; (b) in open pans. 3. Steam evaporation, (a) in jacketed kettles, (b) in grainers. 4. Vacuum-pan evaporation. In this paper only the solar-evaporation processes practised in different parts of the United States will be described. SOLAR EVAPORATION Localities In the Eastern States the solar-evaporation process is not generally employed for climatic reasons. In the Western States, particularly in California and Utah, the great bulk of the salt produced originates in the solar-evaporation process. Of the Eastern States producing salt, this process, so far as the writer is aware, is employed in New York State only.

Jan 9, 1914

Shoemaker: We've all heard a lot about epoxy liner backings. This brings up the question-do zinc furnaces still have a place in a new plant? Meaders: I would, you must understand, be prejudiced in this question because we introduced epoxy backing into the industry. Naturally, we wouldn't have done so if we didn't think it should be done. With that background maybe I could give a little more information on this particular subject than some of the others, because we now have been in this business for some three or four years.

Jan 11, 1967

By Robert C. Linares

Cubic zinc sulfide has been grown from molten salt solutions substantially below the hexagonal-cubic phase transition of 1020°C. Crystals free of birefringence have been grown from molten lead chloride at temperatures from 500° to 800°C. Factors affecting the optical transmission and the birefringence are discussed. CUBIC zinc sulfide is of interest for electrooptic devices and as an optical coating material. However, it cannot readily be produced as large crystals which are free of birefringence. The birefringence arises from the fact that the cubic ZnS is usually grown as the high-temperature hexagonal phase and is transformed to the lower cubic phase by annealing.' This results in stacking faults, stress, and birefringence. A requirement for the growth of cubic ZnS is that it be grown below the phase transition of 1020°C.2 Crystals of cubic ZnS have been grown below 1020°C by the hydrothermal,3 flux,4 and vapor transport5 techniques. However, these all appear to have limitations in size or quality of material produced. It was felt that a new flux method might have a good chance of overcoming some of the previous problems. Mita6 reported the growth of hexagonal ZnS from molten NaCl and wilke7 reported the growth of iron sulfides from molten lead chloride solution, indicating that molten chlorides make good solvents for sulfides. An investigation of a number of possible molten chlorides as solvents showed that molten PbCl2 has an appreciable solubility for zinc sulfide and that crystals can be grown at temperatures from 500° to 800°C. EXPERIMENTAL Crystal growth was performed in open or sealed Vycor or fused silica tubes, in an argon atmosphere or vacuum. There were no deleterious effects due to using vacuum; however, a sealed essentially isothermal system must be used to prevent vapor transport mechanisms from dominating. This will be discussed later in detail. Noble metal containers were not usable as they were severely attacked by these melts. The materials used were: reagent-grade PbC12, reagent-grade ZnS, optical-coating-grade ZnS, and Irtran 2 (ZnS). Crystal growth was accomplished by both slow cooling techniques and gradient growth techniques. In the slow cooling techniques, 15 g of ZnS and 100 g of PbCl2 were used. The components were placed in the silica tube, heated at 800°C for 2 hr, and then slowly cooled (l° to 10° C per hr) to 500°C. The furnace was constructed so that the tube could be inverted, thus allowing the liquid to drain off the crystals at the end of the run. The gradient runs were made by placing the above mixtures in a silica tube at 550° to 600°c, Fig. 1. A temperature gradient was maintained such that the floating mass of undissolved sulfide was 10° to 50°C warmer than the bottom of the tube. Growth occurred on spontaneously nucleated sites at the cooler bottom. RESULTS When using high cooling rates (5° to 10°C per hr), crystals form in thin sheets perpendicular to the {111} face. Crystals 5 by 5 by 1.2 mm, Fig. 2, have been ob-

Jan 1, 1969

PRESIDENT WILLIAM L. SAUNDERS,1 NEW YORK, N. Y. PAST PRESIDENTS CHARLES F. RAID;1 NEW YORK N. Y. BENJAMIN B. THAYER,2 NEW YORK, N. Y. FIRST VICE-PRESIDENT PHILIP N. MOORE,1 ST. Louis, Mo. TREASURER GEORGE C. STONE,1 NEW YORK, N. Y. SECRETARY EMERITUS ROSSITER W. RAYMOND NEW YORK, N. Y. SECRETARY BRADLEY STOUGHTON, NEW YORK, N. Y.

Jan 3, 1915

By John Branner

FIVE of the geologic horizons that yield oil in other parts of the world are represented in Brazil; namely, the Devonian, Carboniferous, Permian, Cretaceous, and Tertiary. Thus far, the first two have shown no, evidences of being oil bearing within Brazilian territory. Not enough exploring has been done to permit trustworthy comparisons of the relative importance of the Permian, Cretaceous, and Tertiary as oil-bearing horizons in this country. The most important, indeed almost the only, information available relates to the locations of the areas and to the structural features of the several horizons. The theories regarding the physical conditions under which these rocks were laid down, however, I regard of the utmost importance. PERMIAN Rocks of Permian age cover an enormous area in Brazil, extending from Rio Grande do Sul to Maranhão on the north, and to Matto Grosso on the west. These Permian rocks in many places are known to include oil-bearing shales and in some locations contain small veins of gilsonite. The geologic map of Brazil shows that the Permian area is widely distributed, but there is considerable doubt about 'the origin of some of the rocks:. Some of the lower Permian beds in southern Brazil contain marine fossils, but in Minas no fossils have as yet been found in them, and in Bahia, at only one locality have a few Permian plants been found. Indications of oil have been found in the states of São-Paulo, Paraná, and elsewhere farther south, but wells drilled in the Permian of São Paulo near the Morro do Bofete did not find oil. One well has been started, by the Brazilian government, in the Permian of Paraná near Marechal Mallet, close to latitude 26° south, but thus far oil has not been found.

Jan 6, 1922

By A. B. Hersberger, R. S. Dean

Although it is obvious that in any flotation process we must have a froth, in recent years the development of collecting reagents has caused the possibilities of better frothing agents to be overlooked. Some investigators have even gone so far as to say that the number of satisfactory frothing agents was sufficient. A little consideration will show, however, that the reagents available in the past were far from ideal frothers. The properties of an ideal frother for flotation work may be set down as follows: 1. It must form in low concentrations a copious but not too persistent froth. 2. It must be insensitive to hydrogen-ion concentration of the pulp; that is, it must froth equally well in an acid or alkaline medium. 3. It must be insensitive to salts, even in high concentration. 4. It must be absolutely noncollecting to both sulfides and nonsulfides. 5. Its frothing properties must not be affected by collecting reagents, including soap, the most generally used nonsulfide collector. 6. It must readily emulsify and disperse any insoluble collecting agent that is likely to be used. Clearly the existing frothers do not qualify. Pine oil, for example, is an acceptable frother for many purposes but if used in soap flotation a delicate balance between pine oil and soap must be struck because, as pointed out by Coghill1, these two reagents are incompatible in certain concentrations. The objections to soap itself as a frother are obvious, and the cresols and their substitution products all have some collecting power and very little emulsifying power. The mechanism of frothing in flotation was early explained on the basis of the Harkins-Langmuir theory of oriented molecules.2 These investigators showed that if an organic compound having an unsym-metrical molecule (in which one end of the molecule contained water-

Jan 1, 1939

By R. S. Dean, A. B. Hersberger

Although it is obvious that in any flotation process we must have a froth, in recent years the development of collecting reagents has caused the possibilities of better frothing agents to be overlooked. Some investigators have even gone so far as to say that the number of satisfactory frothing agents was sufficient. A little consideration will show, however, that the reagents available in the past were far from ideal frothers. The properties of an ideal frother for flotation work may be set down as follows: 1. It must form in low concentrations a copious but not too persistent froth. 2. It must be insensitive to hydrogen-ion concentration of the pulp; that is, it must froth equally well in an acid or alkaline medium. 3. It must be insensitive to salts, even in high concentration. 4. It must be absolutely noncollecting to both sulfides and nonsulfides. 5. Its frothing properties must not be affected by collecting reagents, including soap, the most generally used nonsulfide collector. 6. It must readily emulsify and disperse any insoluble collecting agent that is likely to be used. Clearly the existing frothers do not qualify. Pine oil, for example, is an acceptable frother for many purposes but if used in soap flotation a delicate balance between pine oil and soap must be struck because, as pointed out by Coghill1, these two reagents are incompatible in certain concentrations. The objections to soap itself as a frother are obvious, and the cresols and their substitution products all have some collecting power and very little emulsifying power. The mechanism of frothing in flotation was early explained on the basis of the Harkins-Langmuir theory of oriented molecules.2 These investigators showed that if an organic compound having an unsym-metrical molecule (in which one end of the molecule contained water-

Jan 1, 1939

By Bradley Stoughton

[Secretary's Note.—TO avoid repetition of foot-notes, references to authorities are made in this paper by means of figures, referring to a numbered list in the appendix.—J. S. 1 Introduction. This paper gives the results: first,, of a research into the somewhat extensive literature of titanium; and second, of a series of original tests upon the effect of titanium on iron castr ings. New investigations have also been made upon the effect of titanium on steel, but I hope to treat this subject in an independent paper at some later date, and, therefore, will not discuss the experiments in detail here. The combined results of this study, which extended over a period of more than two years, can be briefly summarized as follows : 1. Steel or cast-iron, in which the titanium is properly proportioned, and which has been properly treated, is improved in strength, toughness, and durability against wear, such 'as, for example, the wear of railroad-rails, of steel and chilled-iron rolls, car-wheels, etc. 2. These improvemerits seem to be caused, not so much by the direct effect of titanium on the metal, as by its cleansing influence in removing harmful impurities, such as oxygen and oxides, nitrogen, occluded slags, and perhaps also sulphur. It appears also to reduce segregation, which would contribute to the same end. 3. In order that its effects may be fully realized, the treatment of steel or iron with titanium must be correctly performed. There are a few simple, but essential, details to be observed; if they are neglected, the best results cannot be expected. To illustrate by an example: A series of tests on cast-iron

Jan 1, 1913

By Robert Williams

A description is given of a double heat treatment of 60-40 brass. Photomicrographs are included to show the changes that take place in the microstructure on reheating the water-quenched specimens. A wide variation in the mechanical properties may be obtained by the described heat-treatment method. ON SEVERAL occasions, when 60-40 brass is first obtained in the beta condition by quenching at about 825° C. and is then reheated, the writers have noticed that recrystallization will take place in the form of twin crystals at the grain boundaries of the original beta crystals. It was, therefore, thought that interesting results would be obtained if this twinning process was studied further, especially as to the temperature at which it first occurs. The material used in the investigation was a bar of extruded muntz metal, 1/2 in. in diameter, and of the following composition: Copper, 60.21 per cent.; zinc, 39.73 per cent.; lead, trace; iron, trace; tin, nil. Specimens I in. in length were sawed from this bar and a hole was drilled into the side of each specimen until it reached the center, and the tip of a platinum-platinum rhodium thermocouple was inserted. A small Hoskins' resistance-type electric furnace was used for heating the specimens. The specimens were first heated at 840°C. for 2 hr. and then quenched in cold water, in order to get the material entirely in the beta state. In every case, in the reheating process, the furnace was brought to the desired temperature before the specimen was introduced. The time occupied in preheating was from 20 to 30 min. By sawing back 1/4 in. on each side of the hole, two parts were obtained from each specimen

Jan 3, 1924

By Alfred Beasley

LEAD-REFINING practice at the. Bunker Hill differs to some extent from that of other United States refineries using the Parkes process, in that the Bunker Hill-has reverted to a custom used years ago of making two kinds of skims, or crusts, in the desilverizing kettles. Also, this was the first refinery to adopt the liquation process for silver skims as developed in Australia. Both of these ideas were brought to the attention of the operator by H. S. J. Sommerset, in the summer of 1924, while he was visiting metallurgical plants in the United States, when he was general superintendent of the Broken Hill Associated Smelters Pty., Ltd., of Port Pirie, South Australia. Since Mr. Sommerset's visit, United States patents on the liquation process have been issued to George Kenneth Williams, of Port Pirie, South Australia. At the Bunker Hill, the lead bullion is conveyed from the blast furnaces to the refinery in brick-lined cast-steel pots, each having a capacity of 5 tons, by a 20-ton electric crane, to which is suspended a Fairbanks-Morse suspension-type scale on which the gross, tare and net weights are obtained. The bullion is poured from the small bullion pots into either one of two kettles of 105 tons capacity, and when a kettle is entirely filled the heavy dross is removed by skimming it into a 5-ton pot suspended by the crane. The crane operator becomes proficient in the manipulation and a kettle is skimmed in a very short time. After the kettle is skimmed clean the bullion is pumped to a kettle of the same size alongside, where the bullion is cooled until it has almost frozen. By using two kettles for the drossing operation, one to accumulate the bullion where the heavy dross is removed, and then pumping to a clean kettle comparatively free of hangings, etc., it is possible to reduce the copper content much lower than if only one kettle is used in the operation. The average yearly analysis of bullion is given in Table 1.

Jan 1, 1930

By Joseph Daniels

The Fritz Engineering Laboratory was built under the direction of John Fritz, and presented by him to the University. A view of the building, looking east, is shown in Fig. 1. The building was started in 1909, and completed in 1910, although all of the equipment was not placed until later. Mr. Fritz gave his personal attention to the details of construction and equipment, and it was his custom to drive over every day to the University from his home in Bethlehem and spend some hours watching the work, offering suggestions, making changes, and planning new work. The result is a building and an equipment which embody his practical ideas. The laboratory structure is of the steel mill-building type, of light-colored brick, 91 by 114 ft., of which a section is shown in Fig. 2 and the floor-plan in Fig. 3. The steel frame carries the roof and traveling crane-way. Ample light has been provided by numerous windows in the side and end walls, in the clerestory, and by a skylight 84 ft. long and 9 ft. wide in the north roof. The main aisle of the building is 49 ft. 2 in. between centers of crane-columns, and has a clear height of 40 ft. The remainder of the width is taken up by two side aisles, 18 ft. high. The laboratory consists of four sections: (1) A general testing-section containing the testing-machinery, a small machine shop, and an office; (2) a cement-testing room; (3) a room for making and storing concrete test-specimens; (4) a hydraulic section.

Jan 1, 1912

By A. Andreas

New Mexico established an annual record by producing 38,897,741 bbl. of oil during 1940. This was approximately 6 per cent greater than the 1939 production of 36,746,840 bbl. The daily average produc-tion was 106,569 bbl. New Mexico retained its position as the seventh oil-producing state. The recommendations of the United States Bureau of Mines were followed by the Oil Conservation Commission in setting the monthly state allowable. At the beginning of the year the average top allowable for each qc-acre unit was 40 bbl. and at the close of the year it was 36 bbl. Remedial work by the operators has been extremely beneficial and satisfactory in reducing the gas-oil ratios in various fields. Gas formerly blown into the air is now being processed by numerous casinghead plants. The Oil Conservation Commission, with the full cooperation of the Proration Office and operators, has taken bottom-hole pressure surveys and has done considerable remedial work in various fields. Two new oil fields and one gas field were discovered in New Mexico during 1940. Numerous extensions to the existing fields were made. Some of these were definitely wildcats in the same townships designated as fields and some, although called extensions, were more than 3 miles from production. Lea County continued to be the largest oil-producing county in the state, with a production of 33,976,394 bbl. It had the largest number of completions during 1940, with 303 oil wells, 9 gas wells and 13 dry holes—a total of 325 wells. Eddy County was the next most active county, with 239 completions, of which 163 were oil wells, 8 gas wells and 68 dry holes. It produced 4,405,158 bbl. of oil during the year. The increased activity in Eddy County and the completion of a large number of producing oil wells have created a transportation problem that can be solved only by additional pipe-line facilities. During the year Eddy County was unable to produce 1,500,000 bbl. of its allowable oil, because there was no pipe-line outlet. There were 601 wells completed in New Mexico in 1940, of which 478 were oil wells, 22 gas wells and IOI dry holes. This was a decline of approximately 9.5 per cent in the number of completions compared with 1939, when 659 wells were drilled. Southeastern New Mexico Lea County.—The largest producing field in Lea County was the Monument field, with 6,894,475 bbl.; followed by Eunice with 6,559,348 bbl. and Vacuum with 4,743,065 bbl. The Hobbs pool, which for years was the largest producing field in the state of New Mexico, was fourth with 3,790,477 bbl. The Vacuum pool was the most active area, having 68 completions, of which 67 were oil wells and one was a dry hole. Only one new field was discovered in Lea County during 1940; the discovery well was in the Caprock area, the Livermore State No. I, in the SE. 1/4 SE. 1/4 sec. 30, T. 12 S, R. 32 E. This well was drilled to a

Jan 1, 1941

By A. Andreas

New Mexico established an annual record by producing 38,897,741 bbl. of oil during 1940. This was approximately 6 per cent greater than the 1939 production of 36,746,840 bbl. The daily average produc-tion was 106,569 bbl. New Mexico retained its position as the seventh oil-producing state. The recommendations of the United States Bureau of Mines were followed by the Oil Conservation Commission in setting the monthly state allowable. At the beginning of the year the average top allowable for each qc-acre unit was 40 bbl. and at the close of the year it was 36 bbl. Remedial work by the operators has been extremely beneficial and satisfactory in reducing the gas-oil ratios in various fields. Gas formerly blown into the air is now being processed by numerous casinghead plants. The Oil Conservation Commission, with the full cooperation of the Proration Office and operators, has taken bottom-hole pressure surveys and has done considerable remedial work in various fields. Two new oil fields and one gas field were discovered in New Mexico during 1940. Numerous extensions to the existing fields were made. Some of these were definitely wildcats in the same townships designated as fields and some, although called extensions, were more than 3 miles from production. Lea County continued to be the largest oil-producing county in the state, with a production of 33,976,394 bbl. It had the largest number of completions during 1940, with 303 oil wells, 9 gas wells and 13 dry holes—a total of 325 wells. Eddy County was the next most active county, with 239 completions, of which 163 were oil wells, 8 gas wells and 68 dry holes. It produced 4,405,158 bbl. of oil during the year. The increased activity in Eddy County and the completion of a large number of producing oil wells have created a transportation problem that can be solved only by additional pipe-line facilities. During the year Eddy County was unable to produce 1,500,000 bbl. of its allowable oil, because there was no pipe-line outlet. There were 601 wells completed in New Mexico in 1940, of which 478 were oil wells, 22 gas wells and IOI dry holes. This was a decline of approximately 9.5 per cent in the number of completions compared with 1939, when 659 wells were drilled. Southeastern New Mexico Lea County.—The largest producing field in Lea County was the Monument field, with 6,894,475 bbl.; followed by Eunice with 6,559,348 bbl. and Vacuum with 4,743,065 bbl. The Hobbs pool, which for years was the largest producing field in the state of New Mexico, was fourth with 3,790,477 bbl. The Vacuum pool was the most active area, having 68 completions, of which 67 were oil wells and one was a dry hole. Only one new field was discovered in Lea County during 1940; the discovery well was in the Caprock area, the Livermore State No. I, in the SE. 1/4 SE. 1/4 sec. 30, T. 12 S, R. 32 E. This well was drilled to a

Jan 1, 1941

By Ira Joralemon

THE Ajo copper district is in the heart of the Arizona desert, near the western boundary of Pima county. Gila Bend, the nearest railroad point, is 43 miles north of the camp, and the little Mexican border town of Sonoita is 30 miles south. Between Gila Bend and Sonoita, Ajo is the only settlement save for one or two small cattle ranches and the uncertain villages of nomadic Papago families. The Little Ajo mountains rise a few hundred feet above wide desert valleys, beyond which are lava mesas. The camp itself lies at an elevation of about 1,900 ft. above sea level, in a little basin on the east side of the range, separated from the open desert by low hills. In the center of the basin the brilliantly iron and copper stained rocks of Copper mountain rise 150 ft. above -the village. Many varieties of cactus and low desert bushes cover the hills, while in the large valleys there are clusters of mesquite paloverde, and ironwood trees which furnish limited amounts of fairly good fuel. A scanty supply of water is obtained from wells in the desert and from prospect pits in the camp. The nearest abundant source of water is the Gila river, 50 miles north of Ajo. (See Fig. 1.) HISTORY OF THE AJO DISTRICT The Ajo, next to Santa Rita, New Mexico, is claimed to have been the first copper district in the Southwest worked by Americans. In the '60's or even earlier high-grade native copper and cuprite Ore was mined from shallow surface workings and hauled by bull team 400 miles across the desert to San Diego. From there it was carried in sailing ships to Swansea, Wales. Later, the ore was hauled to Yuma, floated down the Colorado river to the Gulf Of California, and shipped to Swansea. Bat-infested old workings and the massive axles of the bull carts are shown to prove the truth of the stories.

Jan 8, 1914

PRESIDENT WILLIAM L. SAUNDERS,1 NEW YORK, N. Y. PAST PRESIDENTS CHARLES F. RAND,1 NEW YORK, N. Y. BENJAMIN B. THAYER,2 NEW YORK, N. Y. FIRST VICE-PRESIDENT PHILIP N. MOORE,1 ST. Louis, Mo. TREASURER GEORGE C. STONE,' NEW YORK, N. Y. SECRETARY EMERITUS ROSSITER W. RAYMOND, : NEW YORK, N. Y. SECRETARY BRADLEY STOUGHTON, . . . NEW YORK, N. Y.

Jan 5, 1915

PRESIDENT WILLIAM L. SAUNDERS,1 NEW YORK, N. Y. PAST PRESIDENTS CHARLES F. RAND,1 NEW YORK, N. Y. BENJAMIN B. THAYER,2 NEW YORK, N. Y. FIRST VICE-PRESIDENT PHILIP N. MOORE,1 ..... ST. Louis, Mo. TREASURER GEORGE C. STONE,' NEW YORK, N. Y. SECRETARY EMERITUS , ROSSITER W. RAYMOND, NEW YORK, N. Y. SECRETARY BRADLEY STOUGHTON NEW YORK, N. Y.

Jan 7, 1915

By H. Foster Bain

In the preparation of this series of books it was considered particularly appropriate to include this work. Gunther was one of the younger men who was associated with Colonel Mudd in the finding and development of ore deposits. Supported by Mudd, Gunther undertook a systematic survey of the sources of copper of ancient Europe. This survey resulted in the rediscovery of the deposits now worked by the Cyprus Mines Corporation for which Gunther was, until shortly before his death, the resident manager. In finding and developing these mines, Gunther applied the methods and data embodied in this book and proved their usefulness. It is believed that other young engineers may profit similarly. In presenting a new edition, the form and substance of this work have been preserved and no changes have been made in any direct statement of the original author. Individual illustrations, paragraphs and mine descriptions appearing in the first edition have been omitted in order to permit introduction of new material. The latter has been chosen so as to present a somewhat more balanced picture of the mining industry as it now exists. The new material relates largely to the so-called porphyry coppers, to mines in Canada, Rhodesia, Alaska, and a number in the United States that have become important since the book was first written. The new material was prepared by Mr. Russell C. Fleming, using the best that had been published and items of which he had personal knowledge or had obtained by correspondence with men familiar with the deposit described. Whenever possible the description used has been submitted to the original author for correction. In a number of instances

Jan 1, 1932

By S. C. Jones, J. A. Davis

This paper describes displacement mechanisms of micel-lur solution slugs, displuced by a thickened water "mobility buffer", in a glass micromodel and in consolidated Berea sandstone cores. Colored motion pictures, taken through a microscope, recorded interactions on a pore-to-pore bash in the micromodel. Production and differential pressure data from consolidated cores previously waterflooded to residua1 oil saturation revealed displacement mechani.sm.s macroscopically. Oil is displaced miscibly, while interstitia1 water is displaced immiscibly by the injected micellar. solution slug. Part of this water is dispersed and carried near the lead ing edge of the .slug, and some may remain as a residual saturation. Thickened water displaces any residual water. It also emulsifies with the. slug material, thereby displacing it. The displacement sequence forms banks of oil and water with relatively constant fractional flows, saturations, and mobilities. The mobility of oil and water flowing ahead of the .slug defines .slug viscosity required for stable displacement. Equations are presented that describe. several aspecis of the displacement flow behavior: oil breakthrough, oil cut during production of the stabilized bank, breakthrough of banked water and the resulting decreased fractional flow of oil, fluid mobilities, etc. Breakthroughs, calculated from the equations, are compared with experimental data. Slugs of micellar sollution, ranging from 1 to 5 percent PV, produced unusually high oil recoveries (up to 100 percent) in previously waterflooded consolidated cores. Investigation of the effect of mobility buffer size on oil recovery indicated that recovery is reduced in 3-in. X 4-ft cores for mobility buffer sizes .smaller than 50 percent of the pore volume. Introduction A new oil recovery process,* conceived in 1962, utilizes a slug of micellar solution' that has sufficient viscosity to avoid an unfavorable mobility ratio with respect to the oil and water it displaces. These micellar solutions are composed of hydrocarbons, water, and surfactants, and may contain electrolytes and co-surfactants. The micellar solution is displaced by a "mobility buffer". The mobility buffer is a bank of reduced-mobility fluid, preferably an aqueous polymer solution. The entire system is displaced by unthickened water. This paper describes some of the microscopic and macroscopic displacement mechanisms observed during laboratory development of the fluids for a potential field test. Microscopic phenomena were observed photographically in a specially constructed glass flow model and macroscopic data were taken from constant rate, tertiary displacements conducted in Berea sandstone cores. Qualitative Description of Micellar Solution Flooding This section qualitatively describes displacement mechanisms that occur when a slug of micellar solution is injected into a previously waterflooded core. The slug completely removes oil from the portion of core it contacts, and banks oil in the process. The oil saturation in this bank and the flowing WOR reach definite, fixed values that are determined by water and oil mobilities and slug characteristics. This zone of constant WOR and oil saturation will be called "stabilized oil bank" in the following discussion. When this stabilized bank reaches the outlet end of the core, the oil cut jumps from zero to a constant value equal to the fractional flow of oil. Saline water has little or no solubility in the slug. Because of this. the slug displaces in-place brine immiscibly. During slug injection, most of the brine is displaced ahead of the slug, some is carried along in the leading portion of the slug, and part of the brine may become immobile. The immobile, residual brine is later miscibly displaced by thickened water. Displacement of all the oil and only part of the water during slug injection results in a higher fractional flow of oil ahead of the slug than occurs when all the water is displaced after injection of thickened water is begun. The slug spontaneously emulsifies fresh (low-salt content) water. By emulsification, the slug can become infinitely diluted, and hence totally displaced, by thickened water. Fluid saturations in the core are shown schematically in Fig. 1. Parts A and B show conditions before and after the start of the thickened-water injection, respectively. Since thickened water displaces any residual brine by-

Jan 1, 1969

By Edward Keller

About a dozen years ago the art of bessemerizing copper- * matte, brought to these shores from France, was first established at the smelter, in Butte, Montana, of the Parrot Silver and Copper Company, which had bought the process from Mr. Manhks, the inventor. Through the efforts of Mr. J. E. Gaylord, general manager, and Mr. A. J. Schumacher, snperintendent,, assisted by an able staff, the new method rapidly underwent, at the Parrot establishment, an evolution towards higher perfedion, and within a few years its success and its advantages were so marked that all the great works in the west followed in the footsteps of this pioneer. The converter-process has now practically superseded the reverberatory-process in this country. The latter will undoubtedly, in a not very distant future, be relegated to metallurgical history. The writer has availed himself of what was perhaps the last chance to make comparisons of the two methods, working practically on the same material on an extensive scale, the reverberatory process being that of the Baltimore Copper Smelting and Rolling Company,* while the converter-process is that of the Anaconda Copper Company—both using the matte from the latter company's works in Anaconda, Montana. For the greater portion of the material considered in this paper, the writer is indebted to the two companies. In order to understand the difference of behavior of the several elements, and the difference of the copper produced in the two processes, it is best to study and follow those elements

Jan 1, 1899