Search Documents

By E. J. Gleim

The importance of "good voltage,? especially for direct-current systems in coal mines, is not always fully appreciated. From the practical 4 aspect there are three viewpoints from which low voltage may be considered, namely: (a) its effect upon operation of electrical equipment, (b) its effect upon cost of maintenance and power, and (c) its effect upon safety in the mine. The design of electrical motor-driven equipment usually is based upon a given or assumed constant value for the voltage of the system; consequently, when there is an appreciable drop below this value, unsatisfactory operation is likely to follow. In the case of shaker conveyors, for example, one manufacturer has pointed out that these conveyors must be operated at a certain definite speed if maximum output is to be secured. As shunt motors are used in the conveyor drives, either a rise or fall in voltage will produce corresponding changes in speed and thus seriously affect the efficiency of the conveyor. The introduction of automatic control for mine equipment has been greatly retarded because the relays, contactors, and other special devices required have failed to function properly when attempt was made to operate them on systems subject to variable and low-voltage conditions.

Jan 1, 1937

By J. Ling, L. Racine, P. Cousin, A. R. Laplante

"The problem of gold recovery by gravity from high density gangues is first discussed from a fundamental perspective. Three potential difficulties are presented: poor liberation and fine gold particle size, concentrate bed erosion by coarse dense particles, and slow percolation of gold particle through the high density gangue bed. Two case studies are presented to illustrate the impact of these three problems on circuit performance and the feasibility of gravity recovery. It is concluded that careful testing can determine the scope of the first problem and feed preparation can limit the extent of the second. The third problem is clearly the most serious and results in lower gravity recoverable gold recoveries than would be achieved with the same recovery effort on a low density gangue application.IntroductionSince the commercialisation of the Knelson Concentrator in 1980, gold gravity recovery has experienced a surge in interest, in Canada and the United States first, then Australia, Zimbabwe and Russia, and finally worldwide. Table I details number of units sold in various countries, which corresponds approximately to their importance as gold producers 1. Exceptions. such as the low rank of South Africa or the importance of Zimbabwe, despite the much higher gold throughput of the former, are generally the result of differences in the effectiveness of the local marketing strategies, as well as a reflection of the ""philosophy of recovery"" prevalent in the country.The impact of the Knelson has not been felt equally in all plants. Typically, a highly successful application falls into the following categories: (a) alluvial or hard rock recovery for which gravity is the sole recovery method, (b) hard-rock free gold milling with ores which have a very high gravity-recoverable gold (GRG) content, (c) low grade sulphide copper-gold ores which include flotation ahead of cyanidation and (d) free-milling gold ores ahead of Other applications can be successful, but are not as common. The ""explosion"" of centrifuge concentration, of which the Knelson is the most successful but by no means the sole model, has created a certain euphoria which can be summarized as ""gravity recovery will improve the profitability of gold milling, no matter what."" This presentation is about applications that are not so successful, or even downright unsuccessful. The rationale is not to down-play gold gravity recovery, but to set it in its rightful position: metallurgically, it is not appropriate all of the times; it can become inappropriate if poorly designed; and it can be metallurgically possible but economically unjustifiable. In this paper, this will be illustrated and explained rather than demonstrated, with the use of both industrial plant surveys and laboratory test work. Alternate gravity approaches will be suggested."

Jan 1, 1997

By J. L. Bowlby

The heats of combustion of fuels are determined in the laboratory by means of a calorimeter, usually of the oxygen bomb type. A known weight of the fuel is burned in an atmosphere of oxygen under approximately 400 pounds pressure in a heavy metal container-the bomb- and the heat evolved is imparted to a definite quantity of water. From the rise in temperature, measured by means of a Beckmann thermometer, and other data incidental to the determination, the heat value of the sample can be calculated. On paper, the method appears simple indeed, but in practice the determination of the heat of combustion is one of the most difficult of the various coal analyses. This h as led to considerable investigational work in order to obtain formula: whereby calorific values of solid fuels could be calculated from proximate analysis data al one. The proximate analysis of a fuel consists of the determination of moisture, ash, and volatile matter, with fixed carbon by difference. Sulphur determinations properly belong to the ultimate analysis, but in this section of the country, where the sulphur content of the coal is comparatively high, a request for the proximate analysis of a fuel implies the determination of the sulphur as well.

Jan 1, 1929

By R. Dippenaar

The emergence of new steel grades is largely driven by the need to produce high quality steel at a competitive price. The principal aims are to attain ultra-high purity, (especially low interstitial elements) and ultra-cleanliness (by the control of the inclusion content and size). Whereas the steel used to build the Titanic contained 650 ppm sulphur, resulting in MnS stringer-inclusions 25 mm in length, modern quality requirements for arctic pipelines would only allow 10 ppm of sulphur and inclusions in ball-bearing steels must be smaller than 5µm. Most developments are aimed at hot-metal treatment before refining and ladle treatment after decarburisation. Because ferroalloys are added during or after the refining step, it is the secondary (ladle) refining production technologies that are of specific interest to the ferroalloy producer. Through ladle treatment, hydrogen and nitrogen contents are reduced, ultra-low levels of solute impurities are attained and the shapes as well as the composition of inclusions are modified. Steelmakers are concerned about the cost effectiveness of the use of ferroalloys such as consistent product analysis and delivery, improved financing arrangements and technical support. Minimal variation in product sizing is vital because it impacts on handling problems and because particle size determines the rate of particle dissolution. The required ferroalloy product quality depends on the specific use but in general sulphur, phosphorous and nitrogen contents are of concern. Apart from the presence of trace and impurity elements, ferroalloys also contain inclusions. For example, ferromanganese may contain MnO-MnS-SiO2 inclusions while high-carbon ferro-chrome may contain different kinds of Cr-Mn-spinels. The presence of these impurities and inclusions has a significant impact on steel production techniques and cost and hence, on the selection and use of ferroalloys. The interrelationship between ferroalloy quality and steel production technology is plant and product specific and hence, effective communication between ferroalloy suppliers and steel producers is essential.

Jan 1, 2004

By L. Yuan

To reduce fire hazards from spontaneous combustion of coal in longwall gob areas, a series of computational fluid dynamics (CFD) simulations were conducted by National Institute for Occupational Safety and Health (NIOSH) to model the spontaneous heating of coal in longwall gob areas. The previous modeling results demonstrate that spontaneous heating of coal usually occurred behind the longwall shields and along the face with a bleeder ventilation system. Assuming a stationary longwall face, the spontaneous heating could turn to a spontaneous fire in several days for the most reactive coal under favorable conditions. When the longwall face advances, the spontaneous heating process will be significantly affected. In this study, the effect of longwall face advance on the spontaneous heating in the gob area is investigated using the CFD model developed in previous studies. One longwall panel with a bleeder ventilation system is simulated. The width of the panel is 300 m, while the length of the panel is changed between 1,000 to 2,000 m. The same permeability and porosity profiles are used for gobs with different lengths. The spontaneous heating first develops in the gob when the longwall face is stationary. Then, the face advances at a certain rate. The face advance is simulated as a series of discrete movements, and the effect of the face advance on the maximum temperature developed during the face stoppage is examined. Disclaimer: The findings and conclusions in this report are those of the authors and do not necessarily represent the views of the National Institute for Occupational Safety and Health.

Jan 1, 2009

By Gary Cavanough, Stuart Addinell, Hector Parra

Drilling deep, straight, accurate holes in hard rock to achieve efficient blasting is a challenge for the mining/quarrying industries with short holes normally drilled using “top hole hammer” (THH) and deep holes using “down the hole Hammer” (DTH).

Jan 1, 2013

By Donna lynne Anderson

This report documents the status of a laser-based underground guidance system for tracking and controlling the movements of underground mobile mining equipment. This research is part of a multiple project effort at the U.S. Bureau of Mines to increase mine safety and efficiency by developing technology for computer-assisted mining. Guidance systems, which can track and control the movements of underground mining equipment, are essential during computer-assisted mining operations. A continuous mining machine at the Bureau's surface test facility served as the test-bed for initial development and experimentation of this guidance system. Subsequently, a continuous mining machine in an underground mine served as the platform for in-mine experimentation The first section of this report includes details of the laser sensors, communication network, and computer hardware. The next section includes experimental results, which show the system capable of accurately tracking and controlling the tram maneuvers of a continuous miner underground. The final section discusses conclusions and recommendations.

Jan 1, 1992

By R. Katzenbach, M. Vogler, U. Adamietz

Abstract The design of deep excavation pits in rock mass is dependent as well on the mechanical properties of the rock mass as for example the orientation and the type of discontinuities like bedding planes, joints and fissures, the length of the discontinuities (persistence), the grade of weathering, the strength of rock mass, and the shear strength in the discontinuities, etc., and also on the respective boundary conditions specific for the project, and here especially the geometrical boundary conditions. The basic mutual influences and interactions between these boundary conditions are explained and exemplary presented at an excavation pit with a depth of 18,5 m, situated at a slope with a surface near groundwater table. Résumé La planification des excavations profondes dépend aussi bien de la qualité mécanique du roc, par exemple la location de la texture de la surface de moindre résistance, le degré de rupture, le degré de décomposition, la dureté du roc et la résistance limitée au cisaillement de la texture de la surface de moindre résistance que des conditions limitées spécifiques pour le projet, ici en particulier des conditions limitées géométriques. Les influences et interactions essentielles et mutuelles entre les conditions limitées isolées seront expliquées et présentées à l’aide d’une excavation 18,5 m de profondeur, située sur une pente où le niveau des eaux souterraines est près de la surface. Kurzfassung Die Planung tiefer Baugruben im Fels hängt sowohl von den mechanischen Eigenschaften des Fels wie z.B. der räumlichen Lage des Trennflächengefüges, dem Durchtrennungsgrad, dem Verwitterungsgrad, der Gesteinsfestigkeit sowie der Scherfestigkeit des Trennflächengefüges als auch von den projektspezifischen Randbedingungen hier insbesondere von den geometrischen Randbedingungen ab. Die wesentlichen gegenseitigen Einflüsse und Interaktionen zwischen den einzelnen Randbedingungen werden aufgezeigt und an einer 18,5 m tiefen Baugrube in Hanglage mit oberflächennahem Grundwasser vorgestellt.

Jan 1, 2003

By B. J. Breen, C. S. Mogg

Considerable borehole investigation work has been completed at a proposed site at Sellafield in Cumbria, supplemented by seismic surveys, other geophysical sensing and geological mapping. The focussing of investigation on the rock mass itself will be achieved by means of the planned underground rock characterisation facility, giving access to depths of about 800 m in the strong, low-permeability basement rocks of the Borrowdale Volcanic Group. Characterisation work undertaken during the sinking phase and interaction with continuing surface-based exploration and monitoring should permit a firmer assessment of the long-term safety of a repository. Key considerations in the choice of a design for the repository include the waste handling method, underground inlet cell, underground vaults, vault environment and environmental effects

Aug 1, 1994

By W. Banda

"Trial application of air decks on a production shot improved fragmentation (32% reduction in x50). Empirical fragmentation models and digital image processing software were used to estimate fragment size distribution of the blasted muck pile. The x20, x50, and x80 passing fractions, and top size were 42, 265, 683, and 1,455 mm, respectively. Air-deck application reduced explosives load in blastholes, lowering total charging cost by US$20/hole (15% decrease) and the powder factor to an average of 0.86 kg/m3 (12% decrease). Blast results were 443,624 t of blasted material from the block (90% of total muck pile) was smaller than 900 mm.RÉSUMÉ L’application pilote de trous d’air dans le cadre du coup de mine effectué pour commencer la production a amélioré la fragmentation (une réduction de 32 % des x50). Des modèles empiriques de fragmentation et un logiciel de traitement numérique des images ont permis d’estimer la composition granulométrique des fragments du tas de déblais abattus. Les fractions de passé de crible de x20, x50, x80 et la dimension supérieure étaient représentées par des dimensions respectives de 42, 265, 683 et 1 455 mm. L’application de trous d’air a permis de diminuer la charge d’explosifs nécessaires dans les trous de mine, réduisant ainsi les coûts totaux de chargement de 20 $ US/trou (soit une réduction de 15 %) ainsi que le facteur de chargement (facteur poudre) à une moyenne de 0,86 kg/m3 (soit une réduction de 12 %). Les coups de mine ont résulté en 443 624 tonnes de matériaux abattus du bloc (soit 90 % du tas de remblais total) mesurant moins de 900 mm. INTRODUCTIONThe main objectives of production blasting are to achieve optimum rock fragmentation and to minimize overall production costs. Because blast fragmentation significantly affects the profitability of a mine, blasting is the first step of the size reduction in mining: An optimum size distribution is required to maximize the performance of mining and subsequent milling processes. If the fragmentation size distribution can be modelled and controlled, operations performance will improve. Blast fragmentation modelling is important in mineto- mill optimization: It allows the estimation of blast fragmentation distributions that can be modelled in downstream mining processes to determine the optimum blast design."

Jan 1, 2018

By F. J. Tavera, J. A. Finch

A probe suitable for on-line measurements of gas hold-up in industrial flotation systems has been developed. It is based on an open cell for measurement of slurry-gas conductivity and a novel syphon cell for measurement of slurry-only conductivity. The desired behaviour of the two cells was demonstrated and estimates of gas hold-up were shown to be in good agreement with independent measurements. The gas hold-up probe was used as a diagnostic tool to assess the operation of flotation columns. Differences in gas hold-up between baffled sections in two industrial columns were detected

Jun 18, 1905

By A. M. Tunstall, N. Djordjevic, H. A. Villalobos

The damage zone behind a typical smooth-wall blast in the open pit was assessed by visually examining diamond drill core to identify blast-induced cracking, mapping core rock quality designations to identify changes in fracture frequency and conducting uphole seismic testing to determine changes in rock mass characteristics. The results from the three techniques show reasonable correlation. They suggest that major damage, in the form of fracturing of intact rock, occurs at least 7 m behind the smooth-wall blast and significant damage, in the form of opening and extension of calcite-filled fractures, at least 12 m from the blast. At greater distances the dominant damage mechanism is the loosening of existent joints within the rock mass. In the trachytes at El Soldado these damage mechanisms correspond to peak particle velocities of 2 000, 900 and 500 mm/s respectively

Jun 19, 1905

By Juan Carlos Lozada

YURA S.A. es una empresa industrial cuyo principal actividad es la fabricación y comercialización de Cementos Portland y adicionados, conglomerados de albañilería y concretos. Asimismo proyecta la construcción de una nueva línea de producción de Clinker. En ese sentido, el presente texto señala el sistema de gestión que se utilizó para mejorar las prácticas sugeridas por el PMI (Project Management Institute) en la Guía del PMBOK, y cómo se aplicaron las diferentes herramientas a las situaciones particulares del mismo.

Sep 12, 2011

By R. R. Lowery

This project was proposed to provide information on the hazards associated with arc melting of thorium. A general air-sampling analysis was made to determine the separation, concentration, and distribution of thorium daughter (decay) products throughout arc melting, machining, and forging processes of a thorium handling facility. The value of well coordinated health physics program is stressed in connection with potential health hazards and personnel protection. Building, equipment, and exhaust ventilation requirements for such a facility are discussed. Special handling methods are described for thorium. INTRODUCTION The Bureau of Mines at the Albany Metallurgy Research Center has been involved in handling the naturally radioactive metals, uranium and thorium, for several years. Cooperative work for the Atomic Energy Commission has been carried out with thorium metal, and as a result the concerned laboratories of the Center have accumulated experience on the hazards associated with this metal. This report details the radioactive hazards arising from the arc melting, machining, and forging of thorium.

Jan 1, 1962

By F. D. DeVaney

Manganese-bearing deposits f the Leadville, Colo., district are of two distinct types. Manganosiderite, a combined or intimately mixed ferrous and manganous carbonate, occurs in unaltered zones as the predominant mineral. From 50 feet below the surface to as deep as 900 feet, psilomelane and wad, both black manganese oxide minerals, are found in intimate contact with hematite and limonite. A typical analysis of the black oxide ore shows 20.08 percent Fe, 18.64 percent Mn, 15.91 percent insoluble, 14.91 percent moisture, 0.94 percent Zn, and 2.13 percent Pb. A considerable tonnage of the oxide ore has been mined for production of spiegeleisen and for other purposes.

Jan 1, 1940

By F. D. DeVaney

Manganese-bearing deposits of the Leadville, Colo. district are of two distinct types. Mangano siderite, a combined or intimately mixed ferrous and manganous carbonate, occurs in unaltered zones as the predominant mineral. From 50 feet below the surface to as deep as 800 feet, psilomelane and wad, both black manganese oxide minerals, are found in intimate contact with hematite and limonite. A typical analysis of the black oxide ore shows 20.08 percent Fe, 19.64 percent Mn, 15.91 percent insoluble, 14.91 percent moisture, 0.94 percent Zn, and 2.13 percent Pb. A considerable tonnage of the oxide ore has been mined for production of spiegeleisen and for other purposes.

Jan 1, 1940

By Kenneth Eilerts, Vincent Smith

"INTRODUCTION Knowledge of the Phase relations of fluids produced from combination wells 4/ at the pressures and temperatures characteristic of production from natural reservoirs is essential to efficient recovery and refining practice. An accurate sample of the fluid from such wells may be prepared by mixing (in the proportions of the measured gas:liquid ratio) gas and liquid taken from the separator conditions of steady flow; and physical properties of the sample, at significant pressures and temperatures, may be determined with suitable laboratory apparatus for use in the solution of engineering problems. The results of study of sample so obtained and of mixtures of gas and liquid from the separator combined in other proportions are presented in this report. Attention was given in the study to the relationship between the physical properties of what may be regarded as the constituent materials - the gas and liquid taken from the separator - and the properties of mixtures of these constituents. Data obtained for the complete range of mixture Proportions are expected to provide a reference scale for the study of other combination-well fluids produced at different liquid:gas ratios."

Apr 1, 1942

By Robert H. Peters

The U.S. Bureau of Mines has prepared this report on strategies for maintaining high job attendance among underground coal miners because high absenteeism is a threat to miners safety and seriously hampers productivity. A substantial number of research studies on the effectiveness of various strategies for reducing absenteeism among the employees of nonmining industries have been reported in the literature. These strategies have aimed at improving job attendance through one or more of the following: (1) improving employment procedures, (2) overcoming problems that adversely affect one's ability to attend work, and (3) increasing miners motivation to attend work. Many of these strategies appear applicable to the mining industry, and are reviewed in the first half of this report. The second half of this report describes how one could develop and implement a program for maintaining high attendance at underground coal mines. The steps include: measuring and evaluating attendance levels; formulating attendance goals and an absenteeism policy; developing and implementing an attendance promotion program; and periodically going through the preceding steps known as recycling.

Jan 1, 1989

By Christopher J. Bise

Volume II of this collection of research reports, entitled "Model Training Program," provides the framework and details for developing a tailored training program for a specific mine based upon documented human-performance deficiencies. To do this, several steps must be followed prior to program implementation: 1) background information must be gathered (database analysis), 2) direct observation of indicated problem areas should be conducted (safety sampling), and 3) separation of those deficiencies to be addressed through training from those which would be better addressed by workplace or equipment redesign (trainability assessment). Once training is determined to be the appropriate strategy for addressing the noted deficiencies, several approaches can be taken, depending upon whether the problem is related to repetitive work procedures in a predictable, a variable, or a dynamic workplace with a substantial amount of interaction between workers, equipment, and the environment. Although this volume and the subsequent seven volumes provide examples of how the training information was field tested using various strategies (for example, loss control, task training, etc.) and techniques (for example, microcomputer-based exercises, lectures, etc.), the ultimate selection of the delivery method is based on cost/benefit analysis. Therefore, the Model Training Program has incorporated a Training Cost Model as a desirable component.

Jan 1, 1993

By Holger Witthaus

There is more than a century of experience in multiple seam mining in Germany. In several mines up to 20 seams had been excavated within the last decades. Due to the nature of the deposit and the history of technical development the older panels cause a complex stress distribution for the lower seams and the current longwalls in descending order of mining. The depth of the longwalls reaches up to 4000 ft. This causes a maximum vertical stress that reaches between 30 and appr. 60 MPa. To handle these conditions several support systems are applied for roadway heading. A central knowledge management system for ground control is used for design and dimensioning of support within the DSK. This paper gives an overview to the nature of German multiple seam mining and the solutions in matters of panel layout and support design. It describes the full lifecycle for roadways in the seam starting with the geological and geotechnical evaluation, the basics of roadway deformation in great depth, the development of planning tools and standards for German coal mines, the range of alternative of support systems and roadheading techniques, as well as the reinforcement measures and the processing of support at the T-junction of the face entry. This paper uses exemplary descriptions that are consolidated in a specialized reference book ?Gebirgsbeherrschung von Flözstrecken? ? ?Ground Control in Roadways? which summarizes the standards of ground control based on the development of the past 25 years in German coal mines.

Jan 1, 2007