Search Documents

By J. L. Gregg, J. L.

RECENTLY there has been considerable interest in the production and use of extra hard alloys composed primarily of tungsten and carbon. Dr. Hoyt's recent paper1 gives a good description of these alloys and describes their performance when used as tools. There are a number of these alloys on the market sold under various trade names, and it is the purpose of this paper to describe the results of an investigation of the structure of five of these alloys by means of microscopic and X-ray methods. The samples studied were in the form of small tools or wire-drawing dies, which were either purchased or supplied as samples. They were in some cases not supplied by the original makers but were furnished by the agents in this country, and we wish to call attention to the fact that they may not be truly representative of the materials supplied under the various trade names. No performance data are given and no inference as to the inferiority of one alloy as against any other is made. K. Schröter2 recently described methods for polishing alloys of this type for microscopic examination and has presented photomicrographs of several alloys. However, he did not identify their constituents or describe methods for their identification.

Jan 1, 1929

By Damian Connelly

The metallurgical heart of the majority of copper oxide processes is the heap leaching operation. Fresh low grade sulfide ores is a far greater challenge.The success of this unit operation is so important that operators need to understand the ramifications of their decisions or non-decisions and how they could affect the downstream processing. Heap leaching is an operation that can be described as a scientific art whereby principles of science can be used to guide experienced personnel in attaining their goals. Recent advances have been made based on better understanding the ore characteristics. The success of a heap leach operation, or otherwise, is dependent upon a number of factors, notably: The type of ore to be treated The extent of testwork completed to define the process The interpretation of the testwork results Ore preparation prior to stacking Agglomeration and curing requirements Other issues are: Compliance with the ’smaller’ requirements of environmental authorities Adequate and timely drainage of solution from the base of a leaching lift The degree of saturation in the pads Heap porosity – coarser or finer ore, which is better? Higher or lower irrigation rates – which would produce a better result? Laying out irrigation pipework for ease of operation and maintenance The addition of water, raffinate during agglomeration where needed The heap leaching of sulfide ores, including chalcopyrite, via enhanced bacterial leaching is discussed. INTRODUCTION Over the last twenty years, production of extremely pure copper from solvent extraction and electrowinning (SX/EW) has become more common in a market of real declining prices for copper metal. This paper touches on a number of heap leach operations and experiences. These projects were subjected to extensive engineering design and resulted in low capital cost, efficient operations with a number of lessons learned. The key to these operations was the performance of the heaps and associated fluid collection systems rather than the plants themselves.

Jan 1, 2019

For the purposes of this discussion it is assumed that contributors should express the thoughts that arise from their personal experience. So wide is the range of mineral deposits, and so varied the methods employed in their discovery and development, that no two geologists are likely to have been impressed with the same applications of their science. The author's own personal experience has been, during recent years at least, very largely concerned with the broader aspects of the employment of scientific method and geological knowledge to the problems of exploration and exploitation, for the guidance of the general public and governmental authority rather than of mine executives and directors. The view-point thus reached is likely to differ in many respects from that of men who are much more intimately concerned with the mining problems of a single metal or a single mining field, and for this reason a statement may perhaps supplement those from others whose experience has been markedly different.It may well happen that, at some not distant date in the future, when systematic and comprehensive instruction in economic geology is embodied in the courses- prescribed for mining engineers during their years of training, the author's comments will be quitesuperfluous; but at the present time they appear to him to call for expression.The Need for Training of Mining Men in Economic Geology.Contact over a period of many years with mining men who have had different kinds of training and experience has been convincing that there is a general reluctance to acquire a full rational understanding of the geological factors involved in exploratory and developmental problems. The correction of this attitude is regarded as vital to the industry and it is necessary to insist that the outstanding requirement of the present day is the utilization of all branches of geological, investigation in the field and the laboratoryby men who have had systematic and specialized training in these matters. The science of geology is many-sided, but is, nevertheless, whole and essentially indivisible. No one can afford to disregard any fraction of its content 'or any of its methods of investigation.The greatest advances have been made in the understarnding of the occurrence of mineral deposits by those whose knowledge Qfbasal principles, has been soundest, whose endeavour has been to ascertain all their relationships in space and time, whose attention to detail of all kinds has been keenest, and at the same time, whose capability to distinguish between major and minor features has been most marked.With the passage of the years and the accumulation of data from many lands, it has been possible to build up a great body of information regarding the primary deposition and secondary alteration of mineral occurrences, which is of the utmost value in guiding thesearch for new deposits to take the place of those that become exhausted. This heritage is due not only to the efforts of gifted in...

Jan 1, 1950

By Jackson R. Pressley, Bruce Vandenberg

The knowledge of how and when your explosives go off can help you make intelligent decisions regarding future application of explosives thus removing some of the black magic associated with blasting. The net result will be intelligently set-up shots with timing, explosive charges, and placement more accurately done. Lower operational costs can be achieved when the correct combinations are applied.

Jan 1, 1992

By Qingxiang Huang

Shallow seam coal field has the largest coal reserve in China. Mining in shallow depth causes serious problems. One of them is subsurface dewatering. In this paper, the physical simulating model was performed to study overburden movement and aquiclude stability in the shallow seam mining of Yushuwan coal field, China. According to the characteristic of clay aquiclude in the overburden, the proper simulation materials and proportions of mixture for simulating the plastic clay aquiclude layers and brittle bedrock layers were determined by the stress-strain tests. The physical simulating model was carried out to simulate the failure and caving process of the roof and overburden. Based on the simulating tests, it was found that the movement of clay aquiclude follows the movement of the underlying bedrock layers. The basic caving mechanism of the overburden roof strata was also presented. The tests also showed that the best way to control the stability of aquiclude is to reduce the subsiding gradient Ts. This research provides a foundation for further study on mining dewatering and water conservation.

Jan 1, 2006

By J. M. Houston

"In October 1982, Rio Algom Limited, purchased a tin prospect near East Kemptville, Nova Scotia, from Shell Canada Resources. This purchase led to the development of the first substantial tin mine in North America. This paper deals with the drillingand blasting operations at Rio Algom, in particular the use of emulsion explosives technology.This presentation describes what emulsion explosives and Heavy AN/FO are, and the support system used to deliver these products to the blast site.HistoryThe East Kemptville mine site was discovered by Shell Canada Resources (SCR) in July 1978. SCR started diamond drilling on the tin prospect in March 1979. After 8220 m of BQ drilling, it was estimated a reserve of 56 000 000 tonnes of 0.165% Sn was present.The property, which is located 54 km northeast of Yarmouth, Nova Scotia (Fig. 1), showed, after a feasibility study that, given an ore treatment rate of 9000 tonnes per day, a mine life of 17 years could be expected.GeologyThe tin deposit of the East Kemptville Mine, occurs in granitic rocks at their contact with metasedimentary rocks. The mineralization is in the form of cassiterite with associated sulphides of copper and zinc. The tin occurs in a stockwork of tin bearing Greisen alteration zones.East Kemptville MineThe mine planned an open pit operation with the first five years being mined at a rate of 14 000 tonnes per day, of which 5000 tonnes will be waste and low grade ore. Eventually, the total mining rate will be 21 000 tonnes per day, including 12 000 tonnes of waste and low grade ore. Figure 2 shows the general layout of the mine site.East Kemptville Chooses Emulsion ExplosivesIn December 1984, East Kemptville Mine awarded the Explosives Division of C-I-L Inc. a contract to supply explosives to the borehole. The system chosen gives East Kemptville the on-the-bench choice of regular AN/Fa, or a high density, Heavy AN /Fa product called SuperAN· or a water resistant emulsion explosive called MAGNAFRAC· for holes that cannot be dewatered.Emulsion ExplosivesAn emulsion is an intimate mixture of two liquids that do not dissolve in each other. Emulsions have contributed to our daily lives in such products as insecticides, salad dressings and cosmetics."

Jan 1, 1987

By Luis Haro

Puesto que el deslizamiento de relaves constituye uno de los principales riesgos para la vida y seguridad de los embalses, se desarrolló un programa que rehabilite los depósitos de los relaves a través de los gaviones y geomallas como elementos que estabilizan los relaves descargados. En este sentido, el uso de geosintéticos revolucionó el diseño de los relaves y sistema productivos y permitió un mejor manejo ambiental de los relaves. Asimismo, la utilización de gaviones como paramento externo en el sistema suelo armado, otorga mayor rigidez al mismo en el caso de paredes, taludes más verticales, drenaje y protección contra la erosión. En consecuencia, el uso de gaviones y geomallas es aplicable para la construcción de depósitos de relave y estabilización de depósitos inactivos.

Sep 13, 2001

By A. L. Mular, R. P. Edwards

"The operation of flotation circuits is often regarded as a combination of art and science. Expert systems offer a method by which the art may be captured and supervisory control of flotation circuits fully realized. Operating knowledge, the art, can be consistently employed to enhance regulatory control through the judicious application of an expert system. Using an expert system, a supervisory control routine was developed, and successfully implemented, in the copper flotation circuit at Brenda Mines Ltd.The expert system ran in conjunction with regulatory PI controllers on a personal computer. The expert system received assays via an on-stream analyzer and adjusted regulatory loop setpoints as required in real-time. From its commissioning in November 1989, to the end of the mine's operation in June, 1990, the ES was enthusiastically embraced by the operators and attained operating levels superior to those achievable manually.INTRODUCTIONExpert system (ES) software springs from research into artificial intelligence and is currently making significant inroads into business and industry. Proponents of ES's make many attractive claims; they are a means of capturing the knowledge of experts and they can be programmed by non-programmers. To date, most uses of this software in the process industry are in off-line applications, meaning that the applications are not tied directly to operating (on-line) environments. Moreover, in on-line environments, they are typically employed as advisors and only suggest changes. Human operators are required to close-the-loop to the process. Yet, ES's should be applicable to operating environments and, if the claims of the proponents are valid, should also be better than existing tools. As an intelligent controller an ES must use the knowledge of experienced operators, apply it directly to a process and do this without the intervention of human operators. On-line applications have been successfully employed in the closed loop control of SAG circuits (Herbst et al., 1989) and flotation circuits (Hales, 1989). Harris and Kosick (1988) detail an implementation for flotation control at the Polaris Mine."

Jan 1, 1991

By Larsson Lars-Erik, Rani Isa, Martin Jönsson, Håkan Bredenberg, Mats Larsson

"IntroductionSteel Core Piles are used extensively in Scandinavian countries, where hard rock is found within reasonable depths. A steel core is cast into a drilled steel tube casing and a rock hole is extended below the casing. This pile type is considered a very reliable type of pile, and for urban environment it has several advantages compared to other types of piles. One critical phase of the installation is the drilling of the casing. Usually a DTH (Down The Hole) hammer is used. Drilling in fine grained soils, e g silt, below the ground water level, may give rise to an excessive volume of soil material flushed up from the point of the casing, resulting in unacceptable settlements around the pile installation area.Using a new method for drilling of the casings, the ELEMEX-method has proven to significantly reduce the risk for such problems. In the paper a case record from a ground improvement project in central Stockholm is described. Ground settlements around the drilling area were carefully monitored over a longer period. Both the new drilling method and the conventional DTH casing drilling method where used, so that the corresponding ground settlements could be compared. Settlement records and comments are included in the paper.The paper also gives a description of the project. The installation of new piles and foundation constructions cover a whole city block in Stockholm downtown. The reason for the replacement of the old, damaged wooden piles were due to their destruction caused by a long time lowering of the ground water table. The paper gives a description of the new drilling method as well as an overview of usual urban foundation issues and their solution in Sweden, Finland and Norway.Drilled Foundation MethodDrilled Foundation, using drilling methods originally developed for drilling of large diameter rock holes, is today a standard method for the installation of piles, tiebacks, drilled pile walls and other foundation components, especially in urban built up areas where other techniques as drop hammers, augers, vibratory hammers and other equipment fail to meet the requirement, se ref(1). Drilled foundation is for example used for"

Jan 1, 2014

By M. Yavuz

One of the challenging problems for optimization in mining operations is to choose the best equipment among the alternatives. Equipment selection is an important task for mine management due to its operational cost, and is also an integral part of mine planning and design. Equipment selection is not a well-defined process because it involves the interaction of several subjective factors or criteria. Besides, decisions are often complicated and may even embody contradictions. Therefore, equipment selection is considered as a multi-criteria decision-making process, and suitable decision-making methods should be employed in this process. In this study, the loader selection for Aegean Lignite Colliery was made by using both the analytic hierarchy process and Yager’s method. Owing to the misusage of Yager’s method in the past, a new procedure is proposed in this paper for making proper decisions. It is highly recommended in this purposed method that criteria or alternatives should be grouped so as not to exceed the limitations of human performance (nine criteria/alternatives). The most appropriate solution for the loader selection was investigated by obeying this limitation for each method, and the results were compared. At the end of the decision-making process, a sensitivity analysis was applied for each method in order to see how a criterion affects the final decision. The advantages and disadvantages encountered during the application of each decision-making method are presented.

Jan 1, 2015

By Roger L. Williams

The Bureau of Mines investigated northern New Jersey as a potential future source of yttrium and the rare-earth elements. The studies, consisting of geophysical surveying, sampling, and exploratory drilling, began in the spring of 1959. A total of three and one-half months were spent in the field collecting data. Thirty-three deposits were investigated, of which five demonstrated some potential resources of yttrium and rare-earth minerals. Results indicate that the deposits examined do not contain quantities of yttrium and the rare-earth elements recoverable under present economic conditions. Detailed studies conducted at the Scrub Oaks mine, near Dover, N. J., delineated a yttrium and rare-earth-bearing zone within the magnetite-hematite ore body that represents a potential low-grade deposit. Beneficiation studies on this deposit indicate that a final product, averaging 31.3 percent rare-earth oxides including yttrium, could be produced through amine and fatty acid flotation procedures with 77 percent recovery. Two hundred and eighty-five feet of diamond drill core was obtained from exploration studies conducted at the Bemco prospect in Sussex County. The deposit averages 2.30 percent rare-earth oxides (including yttrium), 0.45 percent uranium and 0.24 percent thorium. Low-grade deposits were identified at the Canfield phosphat2 mine and the Tanners Brook Monazite placers in Morris County, and the Marble Mountain prospect in Warren County.

Jan 1, 1967

By A. P. Whittlestone, J. D. Johnson, R. J. Pine, M. E. Rogers

standpoint. The effect on efficiency of collisions

Apr 1, 1995

THE most important part of the routine survey work on a mine is the keeping up-to-date of plans and sections showing progress of stoping and development work, and the direction of the latter for the purpose of making necessary connections. Except in specialcircumstances, e.g., major horizoittal development, the exactitude required in this work is not extreme, and a method of survey in keeping with the demands of the work itself is all tbat is required.For example, no one would consider measuring the walls of a stope to a fraction of an inch; such extreme accuracy would be wasted.The stope walls being irregular, a mean is usually taken, and for ordinary purposes a survey with a limiting error of six inches is quite satisfactory for the purpose of plotting either stoping or development.It is the author's aim in this paper to describe the method in use at the North Broken Hill Oompany's British mine. This method, while being sufficiently accurate for the purpose in view, possesses the very great advantages of speed and simplicity of operation,with a minimum of necessary equipment. This latter is a very important item where several surveys on different levels have to be carried out on the one day.Let it be understood, however, that the use of this method does not dispense with the theodolite, but simply serves as a convenient adjunct to obtain details and to extend the accurate theodolite survey up rises and down winzes, and through ladderways orwinzes into stopes, where the use of a theodolite, if not actually impossible, is often exceedingly inconvenient. This is particularly so on the British mine, where a large proportion of the ore is won from narrow and complex-dipping lodes, and where vertical ore...

Jan 1, 1928

By LaMar G. Evans

The rapid determination of uranium in ores by radiometric means was investigated by the Bureau of Mines. Among the various procedures and schemes tested, two showed most promise. They were the ratio scheme developed in the Bureau's Tucson, Ariz., laboratory and the equilibrium method developed by the Canadian Department of Mines and Technical Surveys. The ratio method is a simple, empirical procedure for classifying the state of equilibrium in ores by measuring their radioactivity by means of a Geiger-Muller counter under three different conditions, using filters. The principal merit of the method is in providing a clue as to the reliability of equivalent uranium determinations.

Jan 1, 1958

By G. L. Fitzpatrick

Preliminary results of an experiment in seismic holography indicate that the techniques of acoustical holography may be successfully used with seismic waves to determine the size and general shape of underground objects. This experiment was carried out under field conditions on a moderately large scale compared with the typical laboratory experiments in acoustical holography. The object to be mapped was a 100-foot-diameter, spherical, low-velocity zone of explosively fractured rock in oil shale at an average depth of 80 feet. The seismic wavelength of the Fourier component wave used in making the seismic holograms was 50 feet at a frequency of 140 cps. The hologram sampling aperture was 226 feet square and was sampled by 441 geophones in a 21 by 21 rectangular array. One novel aspect of the experiment was the use of a wide-band polychromatic explosive source of seismic waves rather than a narrow-band quasi-monochromatic vibrator source. A successful laser reconstruction of the object image from a lensless Fourier-transform hologram in the form of a 5/l6-inch-square photographic transparency is illustrated. The size of the underground object measured from the laser reconstruction of the object and the size inferred from a knowledge of the amount of explosives used to fracture the site and the tensile strength of the oil shale are found to agree.

Jan 1, 1972

By P. Wells

"In the past decade, there have been many developments in processing of nickel/copper sulfide ores. Improved pentlandite/pyrrhotite flotation selectivity with the use of new reagents, fine regrinding and Redox measurement (control) has led to increased pyrrhotite rejection and thus higher concentrate grades. Flash flotation has increased overall nickel and associated precious group metal recoveries. Recovery of both fine and coarse particles has been improved through an understanding of flotation cell hydrodynamics. The separation of copper from nickel in such ores has seen a similar level of development. From the late 80s to very recently, the use of flotation columns, the use of pyrrhotite depressing reagents and the improved understanding of the complex mineralogy of chalcopyrite, pentlandite and pyrrhotite have considerably increased copper / nickel separation efficiency. Copper concentrate with more than 30% copper and less than 0.5% nickel grade is now obtainable at 80-85% copper recovery from mill feed compared to 70-75% copper recovery with 30% copper and 1% nickel grade only a few years ago. Improved copper / nickel separation in milling operations has the potential to substantially improve the processing of the resulting concentrates and thus the overall return from the extraction of nickel and copper from sulfide ores.INTRODUCTIONNickel metal by itself or in alloys with other metals and materials makes a significant contribution to modern society. The relatively high price that nickel commands compared to other base metals is a reflection of the fact that, although abundant in the universe, nickel is sparingly distributed in the earth’s crust. There are two types of nickel deposits that are currently being exploited: complex sulfide ores and lateritic oxide ores. Lateritic contain no copper but in sulfide deposits, nickel– bearing minerals, principally pentlandite (Pn, [Ni,Fe]8S9), some millerite (NiS) and violarite ([Ni,Fe]S) are often found in association with copper-bearing minerals, mainly chalcopyrite (Cp, CuFeS2) and cubanite (CuFe2S3). The copper content of such ores can vary considerably from as high as 5-8% (in some Sudbury basin ores) to as low as 0.1% (in ores mined by Western Mining at Mount Keith, Western Australia and by Inco in Thompson, Manitoba). The valuable minerals Pn and Cp are almost invariably found associated with pyrrhotite (Po, Fe7S8) which along with nonsulphide rock has to be rejected to tails in the primary milling stage. The bulk concentrate from the primary stage is then treated to depress Pn and float Cp. A complete Cu/Ni separation at the mill would be highly desirable but this is not possible because of locking between a small fraction of the valuable minerals. As a result, Cu/Ni separation has to be carried out both during milling and during refining of the matte following smelting. At Inco, Jinchuan and in Norilsk, a chalcocite / heazlewoodite separation is made by flotation following slow cooling of the matte. In the present Sudbury Inco operations, Cu/Ni separation has not been conducted at the mill since 1991 and all Cu/Ni separation takes place at the matte processing plant. Because of the rising ratio of Cu to Ni in the ore, this strategy is under review and this paper describes some recent studies of circuits in preparation for possible installation of a copper / nickel separation circuit at Inco’s Clarabelle Mill in the Sudbury area."

Jan 1, 2004

By P. P. Andrieux

The recovery of the Zone G crown pillar, located between the bottom of the open pit and the top of the underground workings at the Raglan Katinniq Mine in Nunavik, started in the summer of 2008 and should be completed by the end of 2009. This article describes the rock mechanics-based approach implemented to design the recovery of this valuable block of ore. The stereophotography-based ShapeMetriX3D technique was first used to provide a comprehensive assessment of the various joint sets that comprised the pillar. Then, the statistical distributions obtained for the dip, dip direction, spacing and persistence of these sets were used in conjunction with the geometry of the large-scale faults present in the area to build and run a series of explicit rigid numerical models. Each of these models had a slightly different jointing geometry, randomly constructed from these statistical distributions. Incorporating in a properly formulated numerical model the variability of some of the input parameters has allowed the engineering team to assess in a rational and reliable manner the likelihood of success of the proposed mining method and sequence.

May 1, 2009

By A. R. Dover

The Richmond-San Rafael Bridge is a 6.92 kilometer (4.3 mile) long major toll bridge span that crosses the northern San Francisco Bay in a highly seismically active region. Tutor-Saliba / Koch / Tidewater JV was contracted by Caltrans to conduct a comprehensive seismic retrofit. The JV provided geotechnical planning and quality control services as described herein, under normal oversight by Caltrans. Part of the robust foundation retrofit design included the installation of 26 new, large diameter piles, including eleven 3.81 m (12.5 ft) diameter, cast-in-drilled-hole (CIDH) marine piles that were drilled 9.15 m (30 ft) into the bedrock beneath the Bay, where the water depth ranged up to about 21.3 m (70 ft). These reinforced concrete-filled composite piles have a steel shell permanent casing from the bridge substructure pile cap through the water column and 30.5 to 39.6 meters (100 ft to 130 ft) of marine sediments to the top of rock. This paper discusses construction, inspection (ranging from the QA employed in the planning of the CIDH pile installation methods and equipment to the actual construction inspection required for the routine installation of the shafts), problems that were encountered during construction, and the solutions that were developed and implemented. Inspection, particularly with the usual difficulties in the marine environment, coupled with the difficult and complex bedrock conditions was particularly challenging, and ranged from non-destructive testing to "in-water, inshell" diver inspection. Similarly, the complexities of dealing with both the steel casing "riser" and the associated drilled shaft (rock socket) portion of these composite foundation elements created some unusual issues. The paper also presents important lessons learned from the project.

Jan 1, 2008

By G. E. Christidis, P. W. Scott

The deposits were formed from low-temperature alteration of pyroclastic rocks. Properties investigated include their cation exchange capacity, swelling capacity, pH, rheological properties, the green and dry compressive strengths, shatter index, wet tensile strength, compactability and permeability. It was found that deposits with abundant opal-CT have poor physical properties. The rheological and swelling properties were found to be influenced by the bentonite grade (smectite content) and the degree of disaggregation of the smectite quasi-crystals. The only deposits of high grade which had good foundry properties were those with no opal-CT. Hydrothermal alteration was detrimental to the physical and chemical properties of bentonites in that it decreased the smectite content and the pH and changed the smectite layer charge and the lattice dimensions

Jun 18, 1905

G. R. Compton (Gold Mines of Kalgoorlie (Australia) Ltd., Fimiston, W. A.) : In congratulating Mr. Hooker upon his resume of Mr Parry's paper I have in mind the fact that he carried out the research into pipe pressures. Hydraulic filling as practised in Kalgoorlie has created world wide interest, with these pressures and percolation being vital points.Early in the 1950s, representatives of the Kolar field were conduGted over the local mines where stopes at depths below 2,000 ft were being filled. The problems of pipe pressures were their main consideration since depths of up to 10,000 ft were envisaged.Mr Krishnaiah and Mr Murthy from the same field are with us today and perhaps we may hear of their experiences with depths of 6,000 ft and long lateral lines.J. Holly (Lake View and Star Ltd., Fimiston, W.A.): There is one phase, which I would like to mention myself, that has been very evident in Kalgoorlie operations. That is, we do not get the percolation properties that are obtained on many other fields in the world, and our tendency here has been to assess the quality of our fill more by its settling rate, i.e. the rate at which we can draw off clear water at the surface of the filling levels, rather than the rate that this water percolates down through the fill before it consolidates.We are tending now to measure the quality of our fill as a settling rate rather than as a percolation rate.Americans talk about percolation rates being the important property: If anyone has any experience on operating with fills with different percolation rates, I think their views would be very interesting to the meeting art this stage. Mr ...

Jan 1, 1965