Search Documents

By Peter Moser, Mark Ganster, Andreas Gaich

Surveying of a bench face before blasting is a pre-requisite for a proper blast planning and for a satisfying blasting result both in terms of safety and fragmentation. When surveying a bench face, preferably a large amount of measurement points are required in order to determine the geometry and especially the irregularities with sufficient accuracy. Only contact-free measuring systems allow evenly distributed measurements over the whole bench surface. Existing systems such as total station, laser profiler, or laser scanner show significant drawbacks such as that surveying results are just isolated values of the bench geometry such as heights or profiles, that borehole positions have to be defined in advance in order to know where to take profile measurements and that systems require special surveying skills and that they are expensive too. In order to overcome these difficulties and to provide the blasters a simple tool for bench surveying, blast design and layout and the subsequent back-transfer of the blast plan into the quarry, the Department of Mineral Resources& Petroleum Engineering of the University of Leoben, 3G Software & Measurement company and Mineral AB, one of the largest producers of aggregates in Europe formed a joint venture to develop a new system. Based on an existing stereophotogrammetric system for rock surface surveying and joint analysis (JointMetrix), a new tool was developed within a year. Apart from several mines and quarries using that new tool already today in the daily work, both the Department of Mineral Resources& Petroleum Engineering at the University of Leoben and Austin Powder GmbH Blasting Service did a lot of studies to determine the reliability of the new stereophotogrammetric blast surveying and planning system and its precision in comparison to classical laser surveying equipment. After 1 year of testing and comparison with laser based surveying instruments, it can be concluded, that the new technology of blast surveying& design systems based on stereophotogrammetry is suitable for being used in the daily work routine in quarries and mines. The comparison of the precision of laser based systems and stereophotogrammetric systems has shown, that the deviation between these two types of systems is less than 10 cm, in many cases even lower.

Jan 1, 2007

By Lee Ann Gardner

This U.S. Bureau of Mines publication presents a case study of the processes used in permitting the Nome Offshore Placer Project, a gold mining project offshore Nome, Alaska which operated from 1985 through 1990. The mining project, developed by Western Gold Exploration and Mining Company, Limited Partnership (WestGold), used the BIMA, which was at the time the largest bucketline mining vessel in the world, to dredge gold from the ocean floor. This case study reviews the permitting process from the regulators' and industry's perspectives, as well as characterizing the efficiencies and inefficiencies associated with this case. The Federal, State and local laws applicable to the Nome Offshore Placer Project are identified, agency jurisdiction and interagency relationships are explored, and the chronology of the permitting process is examined. The regulatory authorities for both environmental monitoring and post-mining monitoring are delineated. Significant milestones affecting the project and required regulatory submittals are also included. The case study of the Nome Offshore Placer Project is detailed with respect to agency involvement and coordination, approaches to permitting from both the regulators' and developer's perspective, environmental issues, and permit stipulations which were unique to the project. The advantages and disadvantages of these topics are discussed.

Jan 1, 1992

By D. P. Roberts

This investigation aimed to simulate the experiments performed by Nic Gay (Gay, N.C. 1976. Fracture growth around openings in large blocks of rock subjected to uniaxial and biaxial compression. International Journal of Rock Mechanics and Minining Sciences and Geomechical Abstracts, vol. 13. pp. 231-243) on fracture growth around openings in blocks of rock subjected to uniaxial and biaxial compression, using the Elfen discrete element code. The results of the physical experiments indicated a number of trends that were successfully replicated in the numerical simulations, including crushing ahead of the face, the formation of a sub-vertical tensile fracture at centre-span, the formation of groups of fractures originating from the crushed face zone, the formation of large corner-to-corner fractures which precede sample failure, and linking of slot corner and sample corner fractures leading to sample failure. In addition, other features were apparent that were not reported by Gay. It is believed that these took the form of conjugate shear fractures (as reported by Gay in a previous paper) and other features that may have been altered or inhibited by the presence of pre-existing structure in the physical samples. It was found that the samples, though nominally made up of the same rock type, must have had significantly differing properties. The presence of pre-existing structures may have contributed to this discrepancy. Strain measurements from the physical experiments were reasonably well matched, except where the gauge lay directly in the path of advancing fractures.

Jan 1, 2012

Rational decision making is generally perceived by managers of operations to be a delicate process of committing large sums of money and putting other people's life at risk. Consequently most managers may argue that the decision process requires good judgement, intuition and extreme caution; and not one easily made through the use of fancy mathematical algorithms and computer programs. The advent of artificial intelligence and expert systems in the computer industry combined with recent technological innovations in mathematical and economic problem solving is sure to change this perception. PARETO OPTIMALITY is an economic and a mathematical optimisation concept applied to solving real life operational problems; and one that the current volatile economic forces would require managers to employ because it is virtually real. REALISMM is a computer software package developed using the principles of Pareto optimality, dynamic programming, optimal clustering of information and decision maker interaction to generate decision maker preferred solutions. REALISMM has scope for artificial intelligence and expert systems application for cases where the decision maker is unsure about his objective preferences.

Jan 1, 1993

CONTENTSSummary.Introduction.Location and Geology.Historical and Exploitation.Part 1. Washability Characteristics of the Liddell.Seam.Foybrook Open Cut, Top Bench.Sampling.Size and Ash Distribution.Washability Data.Washery Separations.Part 2. Washability Characteristics of the LiddellSeam.Foybrook Open Cut, Bottom Bench.Sampling.Size and Ash Distribution.Washability Data.Washery Separations.Acknowledgments.References.INTRODUCTIONThe washability characteristics, size-range and chemical analyses of the screening from the Liddell Seam are matters of growing interest in view of the increased exploitation of this seam over the last few years, and also since the Newdell Coal preparation plant of the New South Wales Mining Company Proprietary Limited, utilizing magnetite heavy media separation, commenced...

Jan 1, 1954

By Shanming He, Jinliang Wang, Xiaoming Wang, Chunfa Liao

Large amounts of manganese-rich slag were generated from smelting low-grade manganese ore containing high iron and high phosphorus in electric furnace or blast furnace, which contain 25–40 mass% Mn. This paper describes an efficient hydrometallurgical process for the utilization of high manganese slag instead of conventional usage of pyrometallurgical route for manganese recovery. Pressure acid leaching of manganese-rich slag using air as pressurized gas is studied systematically. The effects of mass ratio of manganese-rich slag to pyrite, concentration of sulfuric acid, leaching temperature, partial air pressure, leaching time, and liquid-solid (L/S) ratio on the separation of manganese with other main impurity components were investigated comprehensively. Under the following optimal process conditions, weight of manganese-rich slag powder,100 g; mass ratio of manganese-rich slag to pyrite, 20:1; sulfuric acid concentration of 140 g/L; air pressure of 0.6 MPa; leaching temperature of 140 °C; leaching time of 1 h; L/S of 7:1; ore size of 75–80 μm; and stirring rate of 600 rpm, the extraction rate of Mn reached 94%, and the dissolution percentage of Si, Al, and Fe are as low as 2%, 6%, and 10%, respectively. The leaching slurry presented a good solid-liquid separation characteristic. The silicic acid formed during sulfuric acid leaching manganese silicates was converted to filterable dehydrated SiO2 particles which precipitated in the residue under the condition of higher temperature with higher pressure. The effect of adding pyrite may be to reduced iron ions and decreased the output of iron hydroxide colloid and also reduced MnO2 to manganese sulfate in sulfuric acid leaching. Thus the formation possibility of colloid such as silica gel and iron hydroxide was decreased, and higher yield of manganese sulfate could be achieved.

By Shanming He, Jinliang Wang, Xiaoming Wang, Chunfa Liao

Large amounts of manganese-rich slag were generated from smelting low-grade manganese ore containing high iron and high phosphorus in electric furnace or blast furnace, which contain 25–40 mass% Mn. This paper describes an efficient hydrometallurgical process for the utilization of high manganese slag instead of conventional usage of pyrometallurgical route for manganese recovery. Pressure acid leaching of manganese-rich slag using air as pressurized gas is studied systematically. The effects of mass ratio of manganese-rich slag to pyrite, concentration of sulfuric acid, leaching temperature, partial air pressure, leaching time, and liquid-solid (L/S) ratio on the separation of manganese with other main impurity components were investigated comprehensively. Under the following optimal process conditions, weight of manganese-rich slag powder,100 g; mass ratio of manganese-rich slag to pyrite, 20:1; sulfuric acid concentration of 140 g/L; air pressure of 0.6 MPa; leaching temperature of 140 °C; leaching time of 1 h; L/S of 7:1; ore size of 75–80 μm; and stirring rate of 600 rpm, the extraction rate of Mn reached 94%, and the dissolution percentage of Si, Al, and Fe are as low as 2%, 6%, and 10%, respectively. The leaching slurry presented a good solid-liquid separation characteristic. The silicic acid formed during sulfuric acid leaching manganese silicates was converted to filterable dehydrated SiO2 particles which precipitated in the residue under the condition of higher temperature with higher pressure. The effect of adding pyrite may be to reduced iron ions and decreased the output of iron hydroxide colloid and also reduced MnO2 to manganese sulfate in sulfuric acid leaching. Thus the formation possibility of colloid such as silica gel and iron hydroxide was decreased, and higher yield of manganese sulfate could be achieved.

Circulating Air Classification of Manufactured Sand Due to environmental concerns, the supply and use of natural gravel has been limited by the Swedish government. The Swedish concrete industry is therefore examining manufactured sand as an alternative that has equal or better product quality, and which the Swedish quarry industry already has the ability to deliver. However, in order to comply with the specifications set by the concrete industry, a better means of classification is needed, as the proportion of fine particles (filler) smaller than 63 - 125 ¦m in size must be reduced. One classification technology that meets the requirements may be air classification. This paper examines the process of circulating air classification, which is not yet commonly used in the Swedish quarry industry; suggesting that a better understanding of the process is needed. The circulating air classifier in this study has two internal machine parameters that can affect the separation point; namely, the speeds of the circulating fan and the separator fan. We study their effect on the separation point as well as the interaction between these parameters. Full-scale parameter tests are also conducted, in which size distribution is measured before and after the circulating air classification. This study shows how the different parameters affect the separation point and that it is possible to produce manufactured sand according to specifications. Computational fluid dynamics (CFD, Fluent) is used to study the internal flow of the air circulating within the classifier. A single-phase study of the flow field is conducted to support and explain the findings from the full-scale tests.

Sep 13, 2010

By Steven J. Page

Researchers have developed a model to describe airborne respirable dust (ARD) generation on surface coal mine drills. By measuring a few basic parameters and using a graph, a drill operator or engi­neer can estimate the relative severity of drill dust emissions as well as how much of a reduction in ARD can be obtained by changing any given parameter. Geometric parameters include: drill deck cross-sectional area, shroud leakage associated with the deck shroud as well as the operational parameters of bailing air­flow, and dust collector airflow. The rela­tionships yield predictive ARD values which fall in the range measured on oper­ating drills for collector/bailing air flow ratios greater than 2. Overexposure to airborne respirable crystalline silica dust can cause serious or fatal respiratory disease. Exposures of sur­face coal mine rock drillers to respirable crystalline silica are of particular concern. In a 1992 alert on silicosis in rock drillers, the National Institute for Occupational Safety and Health (NIOSH) reported on 23 cases of advanced silicosis (acute, acceler­ated, and chronic) ranging in ages from 25 to 60 with drilling tenures ranging between three and 20 years.1 Most of the cases involved drill operators in their 30?s and 40?s, indicating high silica exposure levels are associated with their occupation. A more recent lung x-ray surveillance study of a 664 volunteer population of surface coal miners showed that the prevalence of silicosis-like abnormalities was 9%.2 The two most significant factors associated with these abnormalities were increasing age and years of drilling experience.

Jan 1, 2008

By D. Komljenovic, V. Kecojevic

Selection of the best possible truck type (model) is of crucial importance for the mine decision-makers. In this paper, authors contribute to the body of knowledge by developing a novel methodology for the selection of mining truck. Both the Coefficient of Technical Level (CTL) and Analytic Hierarchy Process (AHP) methods were used in this study. The CTL represents a mathematical function which takes into consideration the interrelations among the main technical parameters of mining trucks. The authors developed a hierarchical structure where both attribute categories and their importance, i.e. priority or weight in the selection process were determined. For each category, a number of sub-attributes and their priorities were assigned, and a pairwise comparison among them was performed using the AHP method. In the final part of the study, the CTL was integrated into the AHP and represents a holistic approach in the selection of mining trucks. A case study on 180 tonnes truck category offered by five manufacturers was carried out. A sensitivity study of obtained results was also performed indicating a very stable solution. The methodology presented in this paper may be used by mining operators to help in the selection of a specific type when acquiring a new truck. It may also be used by equipment manufacturers to help in analysis of potential benefits of envisaged modifications concerning an existing truck type and/or development of a new type.

Jan 1, 2007

By Leonard Weixler, Peter Halbach, Michael Jarowinsky, Johannes Post

Germany as an industrial nation is highly dependent on the import of mineral or metal resources. Sources which have not been considered until now are the marine mineral resources (MMR), which in recent times are enjoying more and more increasing interests and which might provide in the future a considerable contribution to the supply security on metal resources not only for the industrial countries. Backed up by the German government’s "National Masterplan Maritime Technologies" (NMMT) and corresponding industrial R&D-activities, the idea and the advantages of deep-sea mining is gaining more and more interests and supporters with respect to industrial and political considerations on strategic raw material resources as well as on the development of deep-sea mining technologies. The NMMT aims to initiate growth and increase the competitiveness of the German maritime industry on international markets and covers about 10 different marine and ocean technology sectors including deep-sea mining.

Sep 1, 2014

By W. A. Ahrens, J. H. McNamara, J. G. Franek

"An economical, pollution-free process has been developed for the hydrometallurgical extraction of copper from sulphide ores. The extracted copper, in the form of cuprous chloride (CuC/), is converted by reduction to copper metal. The metal is melted and fire -refined into wire bars which meet the standards of electrolytic tough pitch (ETP) copper wirebars. IntroductionThe successful development of the Cyprus Copper Process has been an evolutionary series of events covering a time span of some nine years. The original process, based on an electrolytic membrane cell principle , was abandoned in 1975 because of technical, economic and pollution problems. During the past four years, the pilot plant has been reconstructed based on a new flowsheet and operated successfully in several campaigns, some for as long as four months. The pilot-plant hydro section operates at a 225-lblhr copper rate. In October 1977, a feasibility study was completed by Jacobs Engineering, Pasadena, California. The study showed favourable economic and technical feasibility. Jacob's studies in 1978-79 revealed favourable comparative economics with other known pyrohydro processes and favourable economies of scale.The Cyprus Copper Process converts copper concentrates of varying composition into copper metal, which has been proven to be equivalent in every way to electrolytic tough pitch copper, suitable for electrical applications. This is accomplished at capital and operating costs which are estimated to be lower than those associated with any other known currently applicable technology. Also, the total energy requirement is equal to or less than any other known process and the process is essentially pollution free."

Jan 1, 1980

By Jean-Guy Levaque, Robert Ethier, Ron J. Elliot

This paper presents data gathered during a comprehensive study on the impact of improvements to fragmentation in a major Limestone quarrying operation. The full impacts of gains in fragmentation are tracked through the mucking, crushing, and grinding phases of the operation.

Jan 1, 1999

By Steve Kral

More than 111,350 mining and construction industry professionals from throughout the world gathered in Las Vegas, NV, March 19-23 for ConExpo-Con/Agg 2002 and IFPE 2002. The triennial event is the Western Hemisphere’s largest equipment show for the quarrying, aggregates, construction and ready-mixed concrete industries. Despite the difficulties in the world economy, ConExpo-Con/Agg 2002 attracted more than 2,450 exhibitors from throughout the world. This was an increase from the 1,882 exhibitors that were on hand for the 1999show. And this year’s show occupied more than 180,225m2 (1.94 million sq ft) of exhibit space at the Las Vegas Convention Center. This was an increase from the160,900 m2 (1.73-million sq ft) occupied at the 1999event.

Jan 1, 2002

By D C. Grant, D J. Goudie, E Baird

The Scanning Electron Microscope – Mineral Liberation Analyzer (SEM-MLA) laboratory, as part of the Core Research Equipment and Instrument Training (CREAIT) network of laboratories at Memorial University, NL, Canada, has recently published efforts towards increasing the throughput of automated mineralogy systems by producing single-step trans-vertical moulds, rather than traditional 30 mm polished epoxy moulds. Due to the small particle size of iron ore grains in the -200 mesh size fraction (<75 µm), not all of the surface area on a mould is needed for measurement in achieving good statistical representation. In a new study, trimming of the excess area of a mould results in a smaller sample and increases the quantity of unique samples that can fit in a newly designed trans-vertical adapter for a FEITM MLA 650 field emission gun (FEG) scanning electron microscope. The complete analysis, using a newly designed sample block holder capable of holding 98 samples, required 57 hours of running time where each sample had an average of 33?400 particles measured and identified. The analysis was calibrated to allow for off-line discrimination of hematite/magnetite. The calculated Fe-assay values derived from MLA results were compared to those from bulk sample chemical assay. This shows the Fe assay having a correlation coefficient of >0.99 when the particle count is greater than 20?000. This study represents the most expedient method yet reported to prepare well-polished samples and analyse them in a timely manner that can allow for quicker results in process mineralogy.CITATION:Grant, D C, Goudie, D J and Baird, E, 2017. Analysis of individual - mesh iron ore samples in a single Scanning electron microscope automated mineralogy session, in Proceedings Iron Ore 2017, pp 535–540 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

The Reefton Goldfield on the West Coast of the South Island of New Zealand was a significant gold producing area between 1860 and 1951. During this period it produced approximately 2.1 million ounces (67 tonnes) of gold. The largest single producer on the goldfield and the deepest mine in New Zealand, was the Blackwater Mine at Waiuta which produced 21 tonnes of gold. The Prolubition Shaft reached a depth of 878 metres (317 metres below sea level). The mine closed suddenly in 1951 with about 66 000 tonnes of are remaining in the stapes. Since closure there has been no attempt to determine the ore potential of the mine at depth. This paper summarises the geology, history and resource potential of the mine and sets out two options for evaluating the remaining resource. The options are either deep drilling from surface or recovery of the Prohibition Shaft and underground development and drilling. A schedule for each option is presented and discussed.

Jan 1, 1992

Some important mineral fields are referred to in discussing the formation of placer deposits in Australia.Testing methods include boring by hand, with percussion rigs, with auger and pit digging drills, and by vibro drilling.Sampling errors are minimized by the use of correct techniques and equipment for boring, sampling and sample dressing. A hypothetical set of data is used to demonstrate the final process of evaluation, and somerelevant taxation provisions are discussed.

Jan 1, 1966

By R. Ressel

Keywords: ferrovanadium, thermodynamics, phosphorus Recyclable material is rapidly gaining in importance as a source of raw materials in industrialized countries. This is also the case in the production of ferrovanadium, where, increasingly, materials such as discarded capacitors, spent catalysts, slag, dust and sludge are used. As the V-content in the raw material varies greatly, the demands on process technology are very high. The share of perturbing elements depends very much on the source of the raw materials, which, in turn, makes a corresponding optimization of the various refining steps necessary. The raw materials are mostly available as oxides, which means that carbon, silicon or aluminium are used as reducing agents. Thermodynamic calculations were used to show especially the behavior of vanadium and phosphorus at different process conditions.

Jan 1, 2005

Hot briquetting is a reliable, fully developed industrial concept for the passivation of direct reduced iron produced with the various processes of direct reduction. During hot briquetting, the large specific surface area of direct reduced iron is drastically reduced, and therefore the well-known problems caused by reoxidation and overheating are avoided. Even the shipping instructions published by the International Maritime Organisation (IMO) confirm that Hot Briquetted Iron (HBI) can be handled and shipped without special precautions. From the mid-1970s until today, after extensive pilot testing of the technology, a number of industrial plants for the hot briquetting of direct reduced iron have gone into operation. Additional hot briquetting plants for already established but also for new direct reduction processes are tinder construction or in different stages of planning. This paper describes the characteristics of HBI and its current industrial application for various Direct Reduction Processes.

Jan 1, 1999

The development of Western Mining Corporation's first commercial gold heap leaching operation is described. The laboratory testwork requirements for determining the amenability of ore to heap leaching techniques is discussed. Heap construction and operating practices are described; and production statistics and operating parameters are presented. It is shown that for a specific low grade gold ore a treatment cost optimization can be performed. Taking cognizance of the ore grade, percentage gold recovery, operating costs, and the gold sale price, it can be determined whether Carbon-In-Pulp (C-I-P) or Heap Leaching should be employed as the extraction process. The examples presented in this paper refer specifically to Kambalda and should not be used in themselves as generalities.

Jan 1, 1987