Search Documents

By I. Fedotov

One of the most effective methods of metal surface heat treatment is through laser hardening. In most cases, laser parameters are determined experimentally, which is expensive and time-consuming. A mathematical model for the surface heat treatment process will allow a significant decrease in costs, and reduce the time required for optimization. In the present work, the authors present a mathematical model for laser heat treatment with forced cooling which can be applied to medium carbon steel. The model is based on a three-dimensional heat transfer equation using Green?s function. The model allows one to calculate the temperature of the treated steel at different depths below the surface with and without cooling, for set values of the laser power and travelling speed, when the heat transfer coefficient is a known constant. It also takes variations in the radiation adsorption coefficient on the metal surface and laser beam spot size into account. The model was illustrated by comparing calculated and experimental temperature profiles of mild carbon steel with 0.5% C with and without cooling. A reasonably good agreement was achieved between experimental and predicted values to ensure that a high enough austenizing temperature with short enough cooling time was reached for direct martensite formation. It also predicted the depth of treatment accurately. The incorporation of cooling in the model substantially improves previous models based on heat transfer only. It delivers a tool that can with a reasonable accuracy predict the depth of surface heat treatment and cooling time required from operational parameters, such as laser power, speed of motion, and distance between laser and cooling source, that can be controlled in the work set-up. This can eliminate trial and error efforts and result insignificant time and cost savings. Keywords Laser, surface treatment, martensite transformation, carbon steel, heat treatment.

Jan 1, 2011

By Kim Wiwchar, Elizabeth Mbaja, Lynne Dang, Jim Furey, Anita Marks

"Suncor Energy Inc., located north of Fort McMurray, Alberta, commenced pilot scale operation using a CPT 4’ diameter flotation column in March 2003. This larger scale trial follows two previously successful flotation column bench scale tests. They included an April 2002 trial with a 2.4” inner diameter column from the University of Alberta and a 20” diameter CPT column in August 2002. The column receives middlings stream feed from one of Suncor’s deep cone separation cells and is operated in parallel with a set of WEMCO flotation cells. The recovery, tails losses, and concentrate quality are being compared between the two systems. The column, to date, has been tested with all types of run of mine ore grades. Variables such as wash water flow and temperature, sparger nozzle size and location, sparger air/water flow rates, and column residence time has been adjusted to achieve better recovery and final product quality.Used in many mineral processing applications, column flotation is primarily used for the final stage of sulphide cleaning and flotation of phosphate or iron ore. As well, mechanical cells are often used in combination with a column to retrofit an operation and to produce a cleaner product.Initial results prove that this is the first successful application of a flotation column in an oilsand application. If viable, it will be an inexpensive process for recovery of bitumen from a middlings stream and able to produce a final product suitable for froth treatment.INTRODUCTIONSuncor’s oilsand is surface mined from the Athabasca Oilsand deposit north of Fort McMurray, Alberta. The oilsand is then mixed with hot process water (HPW) and the bitumen is slurried in a pipeline. Large separation cells as shown in Figure 1 float off the bitumen product, which is then steam or static deaerated and sent to Secondary Extraction for further cleaning. The tails stream from the cell is sent to the Final Tails Pumphouse (FTPH) for processing. The tailings flotation froth product gets recycled to the separation cell oilsand feed. The tailings are pumped from the FTPH to tailings ponds. The middlings stream is drawn off the separation cell approximately 9’ from the froth overflow level. It runs down, by gravity, to the scavenger banks for bitumen recovery. It was from this stream off of the Line 6 Separation Cell that the feed to the Canadian Process Technologies Inc (CPT) flotation column was taken."

Jan 1, 2004

By C. F., Christopher

The purpose of any steel-making process is to convert the two raw materials iron and scrap into steel. The chemical analysis of the steel is set within certain limits which involve the physical proper- ties desired by the consumer. In addition to tensile properties a large number of other properties are at the present time desired, such as impact resistance, grain size regulation, specific degrees of hardenability, resistance to creep at high temperatures, resistance to expansion on heat treatment, the ability of the product to undergo extreme amounts of cold deformation without failure, and many other properties which are not directly related to the specified chemical analysis. Variations in many of the properties of plain-carbon steels are due to elements and compounds not included in the ordinary "five element"§ composition. Such variations result primarily from variations in oxidation of the metal in the furnace and from the deoxidation method employed. The steel-making problem therefore resolves itself into two distinct sections: (I) the elimination of certain elements from the charge (the iron and scrap entering the furnace) and the addition of materials to meet the chemical specifications for the heat; (2) the manipulation of the slag and metal and the process of deoxidation to give certain desired properties in the steel entirely apart from the chemical analysis specified. Each of 'these two ends must be attained

Jan 1, 1957

By PALMER LARSEN

INDEX TO GEOPHYSICAL ABSTRACTS

May 1, 1931

By Miguel Rutti

El presente trabajo señala la geología, litología y mineralización del yacimiento minero El Tapado del distrito Yanacocha, situado al norte de Cajamarca. Este se encuentra conformado por diferentes depósitos auríferos epitermales de alta sulfuración, los cuales se desarrollan dentro de un vulcanismo calco-alcalino de composición andesítica a dacítica de edad Mioceno y son correlacionables con la Formación Porculla del Grupo Calipuy. La geología del depósito está conformada por rocas porfiríticas (intrusiones) y flujos piroclásticos tales como tufos de cristales, tufos líticos y brechas piroclásticas afectados por eventos eruptivos de brechas freáticas - freatomagmáticas. Todas estas rocas han sufrido posterior alteración hidrotermal con ensambles típicos de sistemas tipo ácido-sulfato. La mineralización económica está controlada por procesos hidrotermales y se encuentra asociada a sílice masiva y sílice vuggy ( 1-10 g/t Au y estructuras de hasta 136 g/t Au ) y en menor grado sílice alunita y sílice granular (moderada a baja ley).

Apr 22, 2003

By Chung Yu, Wang

CHINA can he roughly divided into three metallogenetic province: North China, the Yangtze Valley, and South China. In North China the old Pre-Cambrian schists and gneisses are represented by the abundance of quartz mines in which sporadic occurrences of copper, lead, zinc, gold, and silver are sometimes found in subordinate quantities. Along the Yangtze Valley and in Central China, extending eastward as far as Shantung, are found here and there intrusions of dioritic rocks, in which occur the famous contact deposits of iron ore, besides which minor quantities of copper. lead, and zinc are also found. In South China the igneous intrunsions are of granitoid type in which, or in the vicinity of which, occur in certain regions immense deposits of antimony, tungsten, tin, and mercury. Broadly speaking. most of the famous coal mines are now situated in regions north of the Yangtze River, in which occur also the sedimentary deposits of iron in contradistinction to the contact deposits of iron along the Yangtze Valley.

Jan 1, 1943

By D. M. A. Flight, P. M. Green, J. A. Plant, P. R. Simpson

Paper presented at Mineralisation in the Caledonides, the Mike Gallagher memorial meeting held in Edinburgh, 27-28 June 1996. The British Geological Survey's regional geochemical database is used to identify the patterns associated with the various mineral deposit types and to examine the extent to which their distribution reflects the presence of long-lived metallogenic provinces in the crust. Image analysis provides new insights into the setting of the mineralisation, geochemical constraints on tectonic models of Caledonide evolution and evidence for terrane amalgamation and large-scale processes. There is evidence that much of the mineralisation reflects the presence of long-lived provinces with a distinctive geochemistry reflecting their origins as zones of crustal extension. In the case of the Middle-Upper Dalradiam sedex deposits, the relationship between geochemistry and tectonic setting is direct. In other cases, rocks deposited in extensional zones appear to have acted as reservoirs of ore-forming elements which were further concentrated during later events

Jun 19, 1905

A short account is given of the theory and practice of determining the true U3O8 content of ore samples by the determination of the beta and gamma activities separately, using the method of Eichholz and his associates.It is shown that, despite the variation of sample activity without change in U3O8 content, the true U3O8 value can still be found.Thorium can be determined simultaneously if this element is also present.

Jan 1, 1957

By Mario Terceros H., Bengt H. Fellenius

"ABSTRACTFour strain-gage instrumented bored piles were constructed in a sedimentary, dense to very dense, fine to medium sand in Santa Cruz, Bolivia. Two of the test piles were the normally used bored pile constructed with bentonite slurry and two piles were Bauer Full Displacement Pile (FDP). One of each pair was equipped with the Expander Body, an inflatable steel cylinder that on pressure-grouting provides an enlarged pile toe. Head-down static loading test were performed on three of the piles and a bidirectional test was performed on the fourth pile, a standard pile with Expander Body and a bidirectional cell placed immediately above the EB. The latter pile was tested in 3 phases. First by activating the cell, second, by a head-down test, and, third, by a repeat bidirectional cell test. The static loading tests proved the shaft resistance of the FDP pile to be about twice that of the standard bored pile and that the Expander Body more than doubled the toe stiffness. The strain-gage records showed that the standard bored piles had multiple bulges and neckings, which affected the evaluation of the axial stiffness and load distribution of the piles. The testing programme was used for a prediction event with 60 persons, ahead of the tests, submitting predictions of the load-movement curves for the test piles and also a capacity appraised from the curves.1. INTRODUCTIONOn April 23 - 26, 2013, the First International Conference and Seminar on Deep Foundations was held in Santa Cruz, Bolivia under the auspices of INCOTEC SRL, the UAGRM University, and the Bolivian Association of Civil Engineers and Chamber of Construction. To coincide with the conference, a research study on construction and static and dynamic testing of four instrumented bored piles was undertaken. To ""add spice"" to the conference, a prediction event was organized on the test programme. This paper presents the soil conditions at the site, the type and construction of the test piles, the outcome of the prediction event, and the results of the static tests.2. SOIL CONDITIONSGeotechnical studies comprising SPT and CPT tests with routine laboratory analysis were performed on recovered soil samples. Three SPT boreholes were put down at three of the locations of Pile TP1, TP2, and TP3, at 5.0 m distance from each other. The SPT procedure consisted of manual hoisting of the weight by three crew members pulling on ropes over a pulley supported by a tripod and letting the weight fall by gravity. The groundwater table lies at 3.5 m depth.Figure 1 shows diagrams of the SPT N-indices and the distribution of water content in the three boreholes. The SPT-indices show the soil density to be compact. The average water content is about 15 %, plus-minus a few percent."

Jan 1, 2014

By C. Richard Groves

As the level of technology applied in the electrical measurement, control, and display portions of mine hoist systems continues to advance, the issues and concerns associated with the ramifications of the application of microprocessor technology on the safety-related aspects of these systems become paramount. This report, in part tutorial, addresses several aspects of these concerns. Beginning with discussions of microprocessor-based system architectures, the report addresses some existing and anticipated uses of this technology in mine hoist systems and discusses safety related considerations associated with the areas of data derivation; control and display panels; and system reliability issues. The report concludes with electrical maintenance and inspection considerations associated with the safety assurance of microprocessor based mine hoist systems.

Jan 1, 1986

By C De-Vitry

"The large Yandi channel iron deposit (CID) is located in the north-west of Western Australia and is currently mined via open pit methods. Drilling at Yandi is widely spaced and current estimates are mostly linear averages of the surrounding local samples. Linear estimates such as ordinary kriging (OK) based on block sizes that are significantly smaller than the dimensions of the drilling grid are less variable than the unknown reality (Armstrong and Champigny, 1989).Conditional simulation (CS) provides a series of plausible realisations that represent the actual grade variability at a small scale (eg 1 m + 1 m + 1 m). These simulations are very useful for a number of purposes, eg: optimising grade control, stockpiling and blending selection of optimal drill hole spacing assessing resource risk on contained tonnage and metal.At Yandi the major constituents of the ore (Fe, P2O5, SiO2, Al2O3 and LOI) are correlated to varying degrees. Independent CS of each assay variable will not reproduce these correlations. Reproducing the correlations (and the shape of scatterplots) is important if the simulations are used for the abovementioned purposes. This paper examines and compares various methods of CS that aim to reproduce the correlations between the assay variables.The CS methods evaluated in this paper are conditional co-simulation (CCS) using the linear model of co-regionalisation and two other, alternative multivariate simulation methods, which use min/max autocorrelation factors (MAF) or the stepwise conditional transform (SCT) to de-correlate assay variables before performing independent CS. It was found that CCS best reproduced the characteristics (histograms, variogram, scatterplots, etc) of the declustered drill hole data (Figure 1). Whilst simulation using MAF generally produced acceptable results, the method did not adequately reproduce the variance of the assay variables. The univariate statistics, histograms and experimental variograms were acceptable for simulations generated from the SCT. Bivariate statistics, cross-variograms and scatterplot reproduction for the SCT were unacceptable. The latter method produced inferior results because there were insufficient samples to obtain a reliable transform of the third assay variable in the transformation sequence.None of the abovementioned simulation methods provides good reproduction of all the scatterplots. This is due to the presence of clay pods, which cause some scatterplots to display two trends. These clay pods contain higher percentages of SiO2 and Al2O3 than the surrounding CID. The clay pods are generally smaller than the drill-grid dimensions. Thus their locations are typically unknown and they cannot be defined by manual interpretation, eg via wireframes. The locations of the clay pods were simulated via indicator CS. CCS was then performed separately for the clay pods and the CID. This significantly improved the reproduction of the correlation coefficients, the scatterplots and visually the simulation was more geologically realistic. Simulating the location of clay pods followed by CCS of assay variables is the recommended approach for simulation at the Yandi CID.CITATION:De-Vitry, C, 2013. Simulation of correlated assay variables - a case study from the Yandi Channel iron deposit, in Proceedings Iron Ore 2013, pp 137-148 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Aug 12, 2013

By Stephen H. Chung

The blasting performances identified above are considered to be the most practical ones for judging the effectiveness of a design combining explosives / rock / drill pattern. In a total blast design process, productivity relates closely to both fragmentation and heave / displacement of muck. In cast blasting, the more overburden displaced by explosives, the less blasted material there is left to be removed with mechanical equipment such as draglines or trucks. For wall protection and dilution control, estimates of the maximum extent of cracks / damage generated in situ due to blasting will help determine the location for drilling and loading perimeter blastholes.

Jan 1, 1994

By Patrícia Freitas Rodrigues

Um comparativo entre dois métodos para determinação das temperaturas de transformação de fase, tendo como base análises de Calorimetria Diferencial de Varredura (DSC) em amostras de uma liga de NiTi equiatômica submetida a tratamentos térmicos para envelhecimento, foram utilizados neste trabalho. Sendo aplicado o método clássico comumente utilizado para análise desses resultados e o método utilizando da integral do pico de transformação de fase. Com base nas avaliações feitas, o método de integral por apresentar uma relação direta da fração de transformação demonstra-se mais eficaz para determinar o início e o fim da transformação por levar em consideração a forma do pico em função da trajetória de transformação.

Aug 8, 2018

By C. Ringas

Pipelines are used extensively in industry to convey various products. Internal corrosion of pipelines can lead to perforation and leakage of the product. A growing problem, not often accurately recognized, is internal corrosion of pipelines caused by bacteria. Microbiologically-induced corrosion (MIC) refers to corrosion caused by a variety of micro-organisms. This form of corrosion is not widely recognized in many industries, although it is widespread and causes many corrosion problems in pipelines, both internal and external. Sulphate-reducing bacteria (SRB) are responsible for the bulk of the corrosion problems caused by MIC. Corrosion caused by SRB is found extensively in water pipelines conveying raw, potable and waste water, as well as in pipelines conveying slurries. This problem also occurs in pipelines conveying crude oil. This paper describes internal corrosion problems of slurry pipelines caused by bacteria and outlines mitigation methods to improve slurry pipeline integrity, thereby extending the life of such pipeline

Jan 1, 2007

The large increase in secondary industries in this country, during the war and post war periods, has caused a shortage of capacity for the production of merchant bar.To overcome this shortage, an expansion of rolling mill facilities has been undertaken by the Broken Hill Pty. Co. Ltd. A small, but modern, merchant mill has been erected at Kwinana in Western Australia and a strip and skelp mill is under construction at Newcastle. The latter mill will roll strip and skelp at present being rolled by the Newcastle 10 in. Merchant Mill, enahling this mill to concentrate on merchant bar production.The Kwinana mill was installed to supply the Western Australian market. This state has a small population (approximately 658,000) and is not at present highly industrialised. It was necessary, therefore, to design a mill which would be capable of producing a wide diversity of sections and could be expanded as the demand increased. To begin with capital expenditure had to be kept within reasonable bounds. The design work for this mill, with the exception of a few specialised items of equipment, was carried out at Newcastle.All design work for the Newcastle mill was carried out by the lVIorgan Construction Co. of America. Although initially intended for rolling flat. products, the designers were asked to make the mill as flexible as possible, so that should the market for flat products decrease, this mill with additional equipment could undertake the rolling of medium sized sections.

Jan 1, 1957

By Lloyd G. Fitzgerald

"The dangerous nature of explosives makes them a potential hazard wherever they are used, but they are likely to exercise their greatest harmfulness under conditions inherent in coal mining. The ease with which explosives can be detonated and the suddenness and violence with which they detonate require great care in their handling and use, if acci-dents are to be avoided. Campaigns have been waged by the manufacturers, the Federal Bureau of Mines, coal-mining companies, and other agencies to educate users of explosives in their dangers and in their proper use and care.Probably 95 percent of the explosives accidents can be attributed to poor judgment, carelessness, negligence, or chance taking. In many explosives accidents it is difficult to determine the cause definitely, as the evidence of the origin is destroyed by the blast and frequently those involved have been killed. Survivors of the accident often are of little help in determining the cause, as the accident occurs so suddenly they cannot tell what happened or prefer not to divulge the information they have because it may point to their own carelessness.A survey has indicated that about 10 percent of all fatalities in coal mines were caused by explosives accidents (excluding gas and dust explosions initiated by explosives). A list of explosives accidents by States, from 1925 to 1932, classified according to the severity of the accidents, indicated that Kentucky and Wyoming had the greatest number of fatalities resulting from explosives accidents. Records of the Bureau of Mines show that 14 coal-mine explosions occurred from January 1 to June 1, 1943. Explosives were involved in four of these explosions. Black powder caused two of the accidents and permissible explosives used in a nonpermissible manner the other two. These statistics are mentioned to show that explosives are still causing severe accidents.Elimination of the hazards associated with explosives begins on the surface. Storage magazines should have no opening, except for entrance and ventilation; ventilators should be screened effectively to prevent the admittance of sparks as well as to prevent unauthorized entrance. The interior should be kept clean and dry, and the floor should be of nonsparking material with no metal exposed. The surrounding area should be kept free of combustible material for not less than 25 feet (and preferably 50 feet) in all directions. Storage magazines should be fire-resistant and reasonably bulletproof."

Aug 1, 1944

By Scott W. Hazen

COMPREHENSIVE summary is presented of results of several years of research at the Bureau of Mines Mining Research Center at Denver on adapting and applying techniques of statistical analysis in mine and mineral-deposit sampling and in computing grade and tonnage of ore for a mineral deposit. In addition to elementary statistical theory the material presented in the bulletin includes: (1) Certain special statistical techniques that have been found useful in mining applications; (2) problems, implications, and limitations that may be encountered in applying these techniques in mine sampling and evaluation; and (3) numerous examples to demonstrate application of the theory and techniques.

Jan 1, 1967

By Swaminathan Srinivasan, Jess A. Schroeder

"Landslide activity along U.S. 50 in Cincinnati, Ohio (USA) has caused roadway damage for decades. After a necessary closure of three lanes due to slope movements, emergency stabilization measures were undertaken to protect the roadway by providing a short-term solution necessitated by The Ohio Department of Transportation budget constraints. The landslide shear plane occurred on a sloping bedrock surface as much as 50 feet below grade. Drilled shafts were installed 40 feet downslope of the roadway shoulder and were heavily reinforced across the shear plane but steel reinforcing did not extend the full length of the shafts and was stopped well short of the ground surface. Instrumentation data has been collected for 11 years after construction has shown these “Stub Piers” have provided much more than a short-term solution and have provided an attractive alternate to conventional deep shafts or tieback drilled shaft options.INTRODUCTIONLandslide activity has occurred along U.S. Route 50 in western Cincinnati, Ohio for many decades. The site is located between North Bend and Addyston, Ohio on the right descending (cutting) bank of the Ohio River. Road distress caused by slope movements required periodic repairs over recent decades. Railroad tracks downslope of the roadway also showed signs of horizontal displacement and periodic repair. Visual evidence in 2005 suggested the shear plane extended below the US 50 roadway and extended out into the Ohio River.A weed and brush-covered slope extended down slope from the roadway at about 3H:1V for a vertical distance of about 20 feet. Above US 50, the hillside continued to rise more than 100 feet. There is a railroad right-of-way at the toe of the slope with the Ohio River bank just downslope of the railroad.In 2005, Terracon Consultants was retained by the Ohio Department of Transportation (ODOT) to perform a geotechnical study that included 17 test borings and inclinometer monitoring at 4 locations. Roadway damage was occurring (see Figure 1). After only a few weeks of monitoring, the inclinometer casings sheared off about 50 feet below grade, near the soil / bedrock interface (see Figure 2). Soon after, the roadway distress worsened, causing ODOT to close 3 of the 4 lanes to traffic and reroute traffic onto the remaining single lane and shoulder. Terracon was asked to develop a stabilization design under emergency repair conditions. However, both limited budget and time-related constraints necessitated a direction by ODOT that the solution be at least “pseudo” short-term (3 to 5 years)."

Jan 1, 2017

By O A. Cottrill, G A. Oldfield, S B. Nowell

Host-rock û wallrock major and trace element geochemistry associated with epithermal gold mineralisation in the Hauraki Goldfield of New Zealand is poorly documented, even though rock geochemistry is a recognised tool in exploration. Such responses assist in recognition of the regional scale imprint of fossil hydrothermal activity, and indicate targets for detailed evaluation within these alteration zones.   Recent investigation of gold deposits in the Waihi (Gladstone), Golden Cross (Empire), Thames (Waiotahi) and Coromandel (Tokatea) areas indicate enrichments of Au, As and Sb in the andesitic wallrocks hosting mineralisation. Of the other elements examined, Si, K and Rb are enriched, and Na, Ca, and Sr are depleted at all deposits. These trends are best developed in the vicinity of veining. In deposits with clay alteration dominating (Waiotahi and Tokatea) there is also depletion of Mg, Mn, Zn and Cu. Ba and Cr are variably enriched or depleted within different styles of alteration. Base-metal enrichment in the wallrocks is not a feature of Hauraki deposits.

Jan 1, 1990

By B Miles, D J. Williams, J Ahn, T A. Vangsness

The flooding of open strip coal mines in the Bowen Basin and Hunter Valley Coalfields of Eastern Australia has the potential to soften the spoil and floor materials to produce “mud”. This mud can act as a slip plane or weak zone when spoil is dumped into it, resulting in geotechnical instabilities. It is therefore important to understand the mechanisms and degree of degradation likely to occur within coal mine spoil of different qualities.To investigate this, five clay mineral-rich coal mine spoil samples were collected from the Bowen Basin, and each sample was subjected to wetting and drying cycles to simulate degradation that could be expected on wetting-up in situ, with their particle size distribution analysed both before and after degradation. These results were compared with the results of a modified slake durability test, in which the entire sample was tested.The paper presents the results of the accelerated degradation and modified slake durability tests on each of the five spoil samples. These results were related to the physical and geochemical characteristics of the samples, which highlighted their importance. The modified slake durability test may be used to rapidly simulate the expected in situ degradation of coal mine spoil on wetting-up, enabling susceptible spoil materials to readily be identified.CITATION:Vangsness, T A, Williams, D J, Ahn, J and Miles, B, 2018. Accelerated degradation and modified slake durability testing of clay mineral-rich coal mine spoil, in Proceedings Mine Waste and Tailings Stewardship Conference 2018, pp 83–96 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 23, 2018