Search Documents

By J. L. van Niekerk

The research project reported on represents the first comprehensive attempt to measure the vibration levels of a variety of tools and equipment in the South African mining industry to determine the effect thereof on the health of workers and operators. Although human vibration has been studied extensively internationally only one reference pertaining to the South African mining industry could be found. From studies conducted in Canada and elsewhere it was evident that rock drills do have potentially hazardous levels of vibration. The scope of the research included measurements on a broad spectrum of tools, machines and vehicles used in the South African mining industry. Both hand-arm vibration, where the majority of the vibration enter the body through the hands, and whole body vibration, where the whole body is exposed to vibration through contact by the buttocks or feet, were investigated and measured. More than 700 sets of vibration data measured on 70 machines at 15 mines and workshops were obtained. Data were obtained for at least 24 different types of equipment and machines that were previously judged to have medium to high levels of vibration. All measurements were conducted in accordance with the international standards: ISO 5349, on hand-arm vibration, and ISO 2631-1, for whole body vibration. The equipment with the highest vibration levels in the hand-arm category was: rock drills, both pneumatic and hydraulic; pavement breakers and jackhammers; hand-held compactors; pneumatic wrenches and electrical hammer drills. Of these the rock drills had weighted vibration levels in excess of 20 m/s2. As far as whole body vibration was concerned the highest values were measured on earth-moving equipment. The major conclusion from this study is that the measured vibration levels are sufficiently high to create an enhanced level of risk of vibration-induced disorders in a significant proportion of the operators of hand-held equipment. The most notable examples are hand-held rock drills, pavement breakers, jackhammers and certain selected workshop tools. The results of the study indicate that a comprehensive epidemiological study should be undertaken on present and past workers to determine the prevalence of vibration-induced disorders.

Jan 1, 2000

By A. G. Doll

"Multi-stage crushing plants, including high pressure grinding roll (HPGR) circuits, require more materials handling equipment than SAG and ball mill circuits. A temptation exists to neglect the energy consumption of materials handling when doing desktop comparisons of HPGR versus SAG milling circuits because estimation of materials handling power requirements can demand significant general arrangement drafting that is not available when performing preliminary scoping or ""desktop"" studies.The largest component of materials handling power is consumed by conveyors when lifting material between stages of crushing, meaning that a simple potential energy model can be used to evaluate conveying specific power consumption. This potential energy consumption for conveying can then be factored to provide overall materials handling specific energy consumption suitable for desktop studies of HPGR and other multi-stage crushing circuits. The technique also permits different crushing circuit flowsheets to be evaluated, at a preliminary level, by simply counting the number of times a conveyor must ""lift"" ore from ground level up to a bin or other equipment mounted up high.INTRODUCTIONTrade-off studies of multi-stage crushing plants involving high pressure grinding rolls (HPGRs) versus semi-autogenous grinding (SAG) mill circuits typically focus on the operating cost savings of crushing plants versus the capital cost savings of SAG mill plants. Very high-level (or desktop) studies of this type do not include a great deal of engineering work, meaning that the details (and costs) of ancillary systems are often not captured when doing the comparisons. The more complicated nature of the multistage crushing plants means there are more ancillary systems than a SAG mill plant, risking a skewed analysis of the operating costs, benefiting the HPGR option.One of the ancillary systems that may be overlooked is the more complicated conveying systems inherent in multi-stage crushing plants. Due to the mass of material being handled in large mining operations, these conveyors become a significant portion of the operating costs. A simple way to estimate the specific energy consumption of conveying systems without requiring engineering drawings and a site layout would allow high-level studies to capture this operating cost."

Jan 1, 2015

By A. V. Pavlov, V. A. Grygorian, Kossyrev, A. E. Semin, A. Korostylev

A new way of producing low-silicon ferrosilicon from iron-ore materials in a new type of aggregate-oxygen reactor is presented. The oxygen reactor process is based on using the calorific combustibility and reducibility of carbon materials inside the aggregate. The key to the process is successful post-combustion of carbon monoxide above a layer of a solid coke bed. Initially the possibility of production of grades of ferrosilicon containing 20 to 25% Si (FeSi20-FeSi25) was studied on a laboratory model of the oxygen reactor. Quartz sand and iron ore concentrates (from Russia and India) were used in the laboratory tests. This test work demonstrated that a ferrosilicon grade FeSi15 could be obtained directly from raw iron ore (containing 75.9 % Fe2O3 and a maximum of 23.8 % SiO2) without using rich iron-ore concentrates. The process was successfully tested on a pilot furnace at Serovsky metallurgical plant. Very promising results and efficiency parameters were achieved. The consumption of materials for 1t of ferrosilicon (15 % Si) production was as follows: 1567 kg raw iron ore, 591 kg of coal (in a composition of ore-coal briquettes), 299 kg of coke (for coke bed formation), and 815 m3 of oxygen.

Jan 1, 2004

By T. G. Carter, R. I. Miller

First, the influence of variation in the

Apr 1, 1995

"At a current mining rate of 3,750 tons per day, La Mine Doyon is currently the largest gold mine in Canada. La Mine Doyon is an open pit gold mine located in the Abitibi area of Northwestern Quebec. The project is a joint venture between Soquem, a Quebec Crown Corporation in the resource development field and Lac Minerals Ltd., a publicly-held, resource development company. Lac Minerals is the managing company and operator of the project.Doyon went into production in 1980 on a very limited basis at 600 tons/day, and has seen a step wise increase to the current rate of 3,750 tons/day. Initially, all the ore was processed at Noranda Mines, Horne Division as flux for the copper smelter. The East Malartic Mill in Malartic was then upgraded and began processing Doyon ore. The third step in the progressive increase of throughput was the commissioning of the Doyon mill in November of 1982. Doyon ore is currently being processed at all three locations.During 1983, an exploration ramp was driven to explore the ore below the ultimate pit depth. Current plans indicate the sinking of a shaft and the commencement of underground mining during the next 2 or 3 years.Since its humble beginning, La Mine Doyon has always been a success; ore reserves have been extended to the east and the west and will soon be confirmed at depth, the mining and processing rates have been increased 6 fold, and the recovery has been increased from a designed recovery of 85% to over 95%. The intent of this paper is to trace the history and reasons for these rather dramatic improvements."

Jan 1, 1984

By Enrique Garay

Actualmente el geólogo de mina toma información rutinaria, mapea los bancos de la mina, los taladros para voladura y loguea los núcleos de perforación y fragmentos del aire reverso. Para la localización en el campo utiliza un GPS que tiene una estación en tierra que permite triangular en tiempo real. En ese sentido, el presente texto señala la importancia de la función del geólogo y las herramientas de campo que utiliza para la exploración y la definición del modelo geológico en la mina Pierina. Así para la digitalización del mapeo geológico utiliza el programa AutoCad, en el caso de mapeo de taladros para voladura emplea un Colector de Datos que posee una hoja de calculo que permite recoger datos del tipo de alteración, porcentaje de arcillas, dureza y tipo de mineralización. Finalmente, la información que genera el geólogo de mina es útil para diferentes usuarios ya que sirve para mejorar el cálculo de reservas, manejar el control eficiente del minado de mineral y desmonte, así como generar el soporte geológico a los geotecnistas responsables del estudio de estabilidad de taludes del tajo abierto, así como desde el punto de vista ambiental es posible definir zonas con potencial de generar drenaje ácido de rocas.

Aug 25, 2002

By W. P. Erasmus

This paper will focus on the use of the ?wet-mix? steel fibre re-in forced shotcrete as a permanent lining in deep shafts, assessing gold bearing reef. It will cover all aspects relating to the choice of this material covering the geological conditions through to the final quality control. All procedures are in line with ISO 9001,as JCI projects who manage the project, are an approved company therof.

Jan 1, 2001

The Tennant Creek goldfield is situated in the Northern Territory, 360 miles north of Alice Springs, or a tot~l distance of 1,300 miles north of Adelaide, and 600 miles south of Darwin. The auriferous area extends 20 miles north and south by 50 miles east and west. The overland telegraph line and the AIice Springs-Darwin road pass through the centre of the field.HISTORY, PRODUCTIONThe country comprising the goldfield was traversed by J. MacDouall Stuart between 1859 and 1861 in the course of his last three exploring expeditions, which terminated respectively at Attack Creek, Newcastle Waters and at the mouth of the Adelaide River. The explorer named Tennant Creek and also Mount Samuel, on which mining operations are now in progress. The overland telegraph line was completed in 1872 and a relaying station established eight miles north of the site of the present township. There was no other settlement in the adjacent country prior to the opening up of the goldfield.Gold was discovered in 1926 on what is known as the Great Northern lease, three miles north of the township. The field was remote; the nearest plant at which gold ore could be treated was at Peterborough, in South Australia, 1,186 miles distant, and it was not until 1932 that the development of the field actively commenced.The production of the field from its inception to December 31, 1939, was 57,895 QZ. of gold, valued at £522,000, recovered from 61,793 long tons of ore, won from 98 mines. In 1940 seven of these mines had reached depths between 100 ft. and 230 ft., the workings of the majority being less than 60 ft. below surface.TOPOGRAPHY, WATERThe country is traversed by parallel and sub-parallel lines of hills trending east and west and rising to altitudes varying from 50 ft. to 100 ft. above the intervening valleys. The low ranges and isolated hills owe their survival to the resistance offered by their indurated, harder rocks to erosion which has removed the softer intervening formations. Their elevation and area depend to a considerable extent upon the presence of; and, the size of, the more or less exposed haematite formations, or are due to the influence of extensive siliceous dykes which traverse the locality.Watercourses head from the hills and either flood out on the flats within a short distance, or in a few cases follow longer courses to the northward. In the channels of the larger creeks billaoongs, which form important water storages for a considerable part of the year, -are to be found. Tennant...

Jan 1, 1942

By Thomas C. Shapiro

Introduction In recent years - even months - the number of articles on computers has increased rapidly. One can hardly pick up a newspaper or magazine without seeing a computer-related article. The article usually explains how the computer will change our lives. Many of us have some concern about the nature and type of change. For most of us, though, the problem is lack of information and understanding about how computers work. In other words, how do we make cost-effective decisions about computers? This three-part series will explain, simply, what a microcomputer is, how it works, and how to decide if you need one. This first article will define terms and briefly discuss areas where computerization might be economic. The second article will discuss geology and mining applications. The third article will discuss plant, administrative, and geotechnical areas as well as the future of software development in the minerals industry. Terms and Concepts All computers have input and output devices and a central processing unit (CPU). Information - instructions and data - is communicated to the computer by means of input devices. These instructions to the computer are converted into language that the computer understands. This causes the instructions to be carried out in the CPU. The result of these operations is translated back into language that we understand. This information is then sent to output devices such as printers and video display tubes. Traditionally, peripherals were devices separate from the main-frame (the CPU and memory) and were used to input, output, and store information or instructions. Today, peripherals perform the same functions though they may be housed in the same cabinet as the CPU and memory. Historically, peripherals included all input and output devices not part of the mainframe. Input devices include keyboards, magnetic tape, and card readers. Tapes and disks are input as well as output devices. Output devices are printers, CRTs (Cathode Ray Tubes), and any mass storage device capable of storing data when directed to do so by the computer or the program. In fact, any mass storage device that can give the computer data when requested is an input device. Mass storage devices include floppy disks (thin, round sheets of plastic covered by metal particles), and hard disks. The latter are thicker and more densely coated with metal particles. This allows much more information to be stored. Another type of mass storage is magnetic tape. Its type and size varies widely. Processing and Storage Any computer understanding must include how instructions and data are processed and stored. Information is stored as a positive or a negative field known as a "bit." There are eight bits in a byte. The bits can be represented as either a one or a zero. Thus the code for a byte representing the numeral one is 00110001. The byte representing the letter A is 01000001. These codes are from the American Standard Code for Information Interchange (ASCII). ASCII defines the standard set of characters including alpha, numeric, and special characters. The computer's memory has allocated locations where instructions as well as incoming information can be stored. All information and instructions are stored as binary numbers bit by bit - zeros and ones. The amount of data that can be stored is referred to as either thousands or millions of bits or bytes. The letter "K" is used to designate one thousand units. The letter "M" is used to mean one millon units (one meg). Disks Thus, a 113-mm (5 1/4-in.) floppy disk - double sided and double density (DSDD) - contains 320,000 bytes (characters) or 320K. This is about 164 double-spaced, type-

Jan 2, 1984

By Efstratios Karampinos, John Hadjigeorgiou, Philippe Morissette

"Ground support is a critical element in maintaining the stability of mining drives in deep and high stress mines. In challenging ground conditions, it is necessary to continuously explore ground support strategies that can control the resulting large deformations. It is an objective of mining operations to optimize the ground support by selecting appropriate systems at the time of installation of each reinforcement element. A successful ground support strategy will result in the use of a system that ensures both the structural and operational integrity of the excavations and mitigates the need for rehabilitation.Preliminary ground support design is often based on empirical observations and methods. Once a design is implemented, field trials, observations and in situ pull tests are used to fine tune or improve the design. Although not often employed during this process, numerical modelling can provide helpful insights into the impact of different ground support strategies. In this respect, it is possible to explore the use of multiple options before selecting the most promising ground support system for implementation in field trials. The challenges associated with the numerical modelling of rock support for mines have been described by Lorig and Varona (2013) and Potvin (2017). The employed numerical models should capture all potential failure modes of reinforcement throughout the mining sequence of the excavation. In particular, it is important to emulate the observed in situ ground support performance, as well as the influence of the installation sequence of the support. However, the time and expertise required for this type of modelling of ground support is often not available at mine sites. Even when the expertise is available, it requires a major time commitment and commitment of resources to set up, run and calibrate the sophisticated models capable of explicitly capturing the behavior of ground support.Rock reinforcement is an integral part of all ground support systems used in underground mines. Long, flexible tendons can reinforce the rock mass deeper into the walls and create a thicker reinforced shell around the underground excavation. This article focuses on the optimization of the cable-bolting strategy in squeezing conditions at the LaRonde Mine in Quebec, Canada by integrating the 3D distinct element method (DEM) in the design process. A calibrated numerical model is used to investigate a series of cable bolt configurations and provide recommendations for the ground support design."

Jan 4, 2018

By A. More, J. Bullón

Metal casting is one of the most important operations in ferroalloys factories. After the tapping of the furnace and the depuration of the metal, the preparation for customers with cooling, crushing and sizing begins. In total production costs, this contains around 8 % of the total cost of the metal, depending on the value of the fines and other important parameters. From an investment point of view, this represents around 20% of the total capital for a new furnace. Casting onto a water-refrigerated copper plate is not new for molten metals. In steel, continuous casting machines are normal in every factory. Water granulation casting exists at some ferroalloys plants. However, the majority of plants and production technology still use the technology of lumping, crushing and sizing. This technology is time consuming, produces fines and requires a relatively large work force. In 2001, Ferroatlantica put into operation a new water-cooled copper casting-machine, which seems to be a very convenient solution to solve all these problems. It is in operation at a silicon factory; the same place where the new ELSA electrode was developed for silicon metal production. This paper describes our experiences using it.

Jan 1, 2004

A series of gas inrush events occurred during development at Grosvenor mine resulting in exposure to elevated levels of methane at the production face. A total of 22 gas inrush events occurred releasing between 15 and 130 m3 of methane during each event. The presence of an undrained seam in the immediate floor, geotechnical characteristics of the floor, and the stress environment all contributed to these dynamic floor events, while the geological characteristics of the seam below, such as the seam thickness and ash content of 75%, prevented effective pre-drainage. However, events only occurred in headings mined parallel to the principal horizontal stress direction. In cut-throughs (C/Ts) perpendicular to the principal stress direction, no events occurred, and higher methane levels were observed at the production face.

Jan 7, 2020

By R. Tyreman, G. Ritson

"The Red Lake Mine is situated in Balmer Township, Red Lake area in northwestern Ontario. It is an underground mine that has been in production since 1948. The property was originally known as the Dickensen Mine and was shut down in 1996.A feasibility study was carried out in 1998 and it was determined that a new mill should be constructed with a throughput rate of 600 stpd. The life-of-mine average gold grade was projected to be 1.35 oz/t with gold predominantly associated with arsenopyrite and pyrite. Metallurgical testwork indicated that the optimal flowsheet for gold recovery would include an autoclave for oxidation with a carbon circuit for adsorption. To limit capital cost and establish cashflow, the mill was constructed without an autoclave. The recovery by gravity and cyanidation was projected to be 83%. A flotation plant was constructed at the tail end of the circuit to recover the additional gold associated with sulphides from the leach circuit tailings. This material is being stockpiled onsite for future oxidation treatment.Detailed engineering was started in early 1999 and the first gold was poured in August 2000. One feature of the project was the use of Contact Lake equipment from Cameco’s Contact Lake project. The entire mill was purchased and equipment re-used where possible. The capital cost for the process facilities was C$3 1.5 million."

Jan 1, 2001

By John Lindsay

"Although diamond mining is a relative newcomer to the Canadian mining industry, with the first diamond mine coming on stream in 1998, Canada is already a significant producer of high quality diamonds. This paper will review diamond production trends and highlight some of the projects currently under development, which have the potential to enhance Canada’s role as a significant diamond producer.Diamond recovery plants generally incorporate well-established mineral processing and recovery techniques, with issues such as product security, cut-off sizes, and diamond preservation becoming important considerations when developing process flowsheets. A diamond processing plant must achieve three key objectives, namely:• Liberation of the diamonds from the host rock;• Separation of the heavy minerals, which include the diamonds, from the host rock;• Recovery of the diamonds from the heavy mineral concentrates.Processing technologies and equipment commonly utilized in diamond processing plants will be reviewed and some of the significant issues associated with each option briefly discussed.Typical process flowsheets will be presented.Finally, an overview of De Beers’ Victor diamond project, located in northern Ontario, will be provided. This potentially significant diamond producer is currently at a pre-feasibility stage of development.DIAMONDS IN CANADAWorld Diamond ProductionCommercial diamond mining commenced in earnest with the discovery of the Kimberley diamondfields in South Africa in the late 1800s, and this resulted in a dramatic increase in the supply of diamonds. As can be seen from figure 1, world diamond production, mainly from South Africa, Angola, Congo, and Namibia, remained relatively constant through the early 1900s until the development of the large Russian kimberlite pipes in the 1950s. Production increased again in the 1960s and 70s with the development of the Botswana mines, but the most significant increase in global production came from the Argyle mine in Australia, which came on stream in 1983 and produced a peak of almost 43 million carats in 1994, representing approximately 40% of the world market. Production from Argyle has since fallen-off as grades have declined and the strip ratio has increased with the deepening of the open pit."

Jan 1, 2003

By Makoto Kimura

Failure tests on laterally loaded single and pile group are analyzed with a 3-dimensional elasto-plastic finite element program. In the analysis, the mechanical behavior of the ground is supposed to be elasto-perfect plastic with Drucker-Prager's yielding criterion. The nonlinearity of the piles is simulated by assuming a hyperbolic relation between the bending moment and the curvature of the piles. The influence of the axial stress on the cast-in-place concrete piles is also considered in the numerical analysis. It is found that the mechanical behavior of the piles subjected to lateral loading, such as the load-displacement relation up to an ultimately large deformation, and the distribution of bending moment in the pile group can be well simulated.

Jan 1, 1996

By Vincent A. Scovazzo

Benchmarking is a business management process that seeks improvement through the study and reapplication of practices conducted by industry leaders. This discussion presents objectives and organization of benchmarking applied to mining geomechanics. Similar procedures have been successfully applied to mining companies, laboratories, and research organizations involved in mining geomechanics throughout the world. Benchmarking is a structured process that allows an organization to learn from the "best" in the field. The objectives of benchmarking vary depending on the company's targeted areas for improvements. Typical goals include ground control cost reduction, enhanced safety, optimization of geotechnical staffing, development of state-of-the-art design procedures, or the adoption of the "best in the field" geotechnical data management. Once the objective of the study is established and the practices and procedures to be benchmarked are identified, a benchmarking team is formed from internal and outside specialists. Benchmarking in geomechanics is fundamentally different than in most other fields because of the effects of local geologic conditions and regulations, both of which must be understood by all on the benchmarking team, before a comparative analysis can be made.

Jan 1, 2000

By Jerry C. Tien

Mining in China dates back at least 4,000 years. Today, with no less than 103,000 metal/nonmetal mines and between 40,000 to 80,000 coal mines, China’s mining industry is undoubtedly the largest in the world. Despite improvements in recent decades, seemingly endless mining accidents continue to make the news. Official coal mining deaths were 6,702 in 2003, and 6,027 miners died in 2004; actual figures may be much higher. Added to these were the 2,699 deaths in the metal and nonmetal industries. Most of these accidents were due to CH4 (methane gas) explosions and fires as a result of inadequate mine ventilation de-sign or practices. A good portion of these accidents occur in small, privately run and often technically illegal mines. During the past 10 years, the Chinese government has attempted to crack down on small and often technically illegal mines without much success. The number of accidents and associated fatalities has not significantly reduced. However, there appears to be a new urgency in China’s efforts to step up mine safety in the country. After its worst reported mine disaster in more than a half century, the government quickly paid reparations to families, suspended high-level officials in charge and announced additonal reforms. One of those was the elevation of the central government’s work safety office to cabinet-level status. There has been increased transparency in reporting and investigation of mine accidents and disasters in recent years. There has also been an increase in public criticism by labor leaders concerning the neglect of mine workersafety.1 This article examines the causes of China’s many mining accidents, current legal and enforcement structures, respective mining health and safety related laws and regulations, recent mining industry developments and the latest effort to curtail small mining operations.

Jan 1, 2005

By O. T. Rämö, E. Suikkanen

Episyenites are sub-solidus, quartz-depleted alkali-feldspar-rich rocks. They form veins and lenticular bodies in granitoid rocks and migmatites in a late- to post-orogenic or anorogenic setting. Leaching of quartz is usually a response to a flux of weakly saline hydrothermal solution in circulation cells above cooling intrusions, where sufficient fluid-rock ratios and thermal gradients are achieved. Fluid Si-undersaturation is achieved by rapid cooling within the field of retrograde Si solubility or by temperature and pressure increase outside retrograde conditions. Some quartz may also be consumed in metasomatic reactions and in response to pressure fluctuation in sealed episyenite bodies. The small size and overall rarity of episyenites imply that conditions for episyenite formation are not commonly encountered in the crust. In addition to quartz depletion, episyenites record complex histories of metasomatic alteration and hydrothermal mineral growth. Nearly all episyenites have undergone Na-metasomatism, which may have led to the formation of nearly monomineralic albitite, and which is occasionally followed by late K-metasomatism, phyllic alteration, and argillization. Depending on the effectiveness of later compaction, recrystallization and vug-filling episyenites may preserve the macroscopic porosity formed by quartz dissolution and brittle deformation. Vuggy episyenites can act as significant sinks for metals carried by crustal fluids and host many significant U, Sn, and Au deposits worldwide. Rare earth-critical syenitic fenites around alkaline intrusions share mineralogical and genetic traits with episyenites.

By O. T. Rämö, E. Suikkanen

Episyenites are sub-solidus, quartz-depleted alkali-feldspar-rich rocks. They form veins and lenticular bodies in granitoid rocks and migmatites in a late- to post-orogenic or anorogenic setting. Leaching of quartz is usually a response to a flux of weakly saline hydrothermal solution in circulation cells above cooling intrusions, where sufficient fluid-rock ratios and thermal gradients are achieved. Fluid Si-undersaturation is achieved by rapid cooling within the field of retrograde Si solubility or by temperature and pressure increase outside retrograde conditions. Some quartz may also be consumed in metasomatic reactions and in response to pressure fluctuation in sealed episyenite bodies. The small size and overall rarity of episyenites imply that conditions for episyenite formation are not commonly encountered in the crust. In addition to quartz depletion, episyenites record complex histories of metasomatic alteration and hydrothermal mineral growth. Nearly all episyenites have undergone Na-metasomatism, which may have led to the formation of nearly monomineralic albitite, and which is occasionally followed by late K-metasomatism, phyllic alteration, and argillization. Depending on the effectiveness of later compaction, recrystallization and vug-filling episyenites may preserve the macroscopic porosity formed by quartz dissolution and brittle deformation. Vuggy episyenites can act as significant sinks for metals carried by crustal fluids and host many significant U, Sn, and Au deposits worldwide. Rare earth-critical syenitic fenites around alkaline intrusions share mineralogical and genetic traits with episyenites.

By Rees J. Llewellyn

Improved product development, assessment methods and evaluation studies of materials for oil sands applications have traditionally focused on low and high stress abrasion and slurry erosion resistance mechanisms, because they were considered to be the predominant wear modes prevailing in oil sands mining, transportation and bitumen recovery. More recently with the very successful introduction of oil sands hydraulic transportation systems, there has been increasing use of crusher systems in which materials of construction are also required to have good toughness and gouging abrasion properties to withstand impact and the severe indentation and ploughing forces that are involved. To assess material property requirements for mitigating this additional wear mechanism, jaw crusher gouging abrasion tests using a modified ASTM G81 procedure, have been carried out on a range of wear materials of interest for oil sands mining service. The method involves a comparison of the wear losses that occur for reference and selected test plates when a controlled amount of standard feed rock is comminuted in a laboratory jaw crusher. Among the classes of material evaluated have been Q&T plate steels, austenitic manganese steel, chromium and chromium molybdenum white irons as plain castings and in laminated forms and also chromium carbide and tungsten carbide overlaid wear plates.

May 1, 2004