Search Documents

Assessment of the Consistency Between Different Laboratory Froth Stability Measurements

Sep 13, 2010

By R. A. Meister

The study on improving surface coat refuse disposal site inspections included surface inspections of 15 refuse disposal sites. Monthly aerial photos were taken of the sites and computer methods were used to determine elevation changes. Photogrammetric techniques that were used are described in detail. A comparison of the results of each of these inspection techniques is included. A detailed evaluation of the photogrammetric techniques was made and conclusions were drawn concerning the advantages and disadvantages of using aerial photography and photogrammetry as part of the inspection procedure. Operators' opinions of the aerial photography methods are included.

Jan 1, 1980

By Dany Pelletier, Yeves Breau, Ahmed Bouajila, Claude Gagnon

"In flotation circuits, direct measurement of the volumetric flow rate delivered by electromagnetic flowmeters is often difficult to obtain particularly due to piping and flow constraints. However, on-line material balance calculation could offer a reliable alternative to flow rate sensing. This paper describes an on-line material balance software package as applied to a copper flotation circuit for mass flow rate estimation mainly based on the output of an x-ray fluorescence onstream analyser. Rule-based procedures for the management of the main calculation modules are designed and integrated to a Comdale expert system. Attempts to diagnose the flotation process from mass flow rate data are also discussed.INTRODUCTIONThe need for improved process diagnosis, control and optimisation has become more evident for the mineral processing industry in the last decade. Therefore, new process variables need to be inferred or measured particularly in highly multivariable processes such as flotation. This process is subject to a wide variety of disturbances mainly generated by frequent and sometimes abrupt changes in physical and chemical characteristics of the ore and due to some irregularities in manual process operating procedures.A flotation circuit scheme is always a complex network counting more than two dozens of slurry streams. Information about those streams (%solids, metal content analysis, and flow rates) are important for process diagnosis, performance evaluation control and optimization (1,3).On-line sensing instruments such as x-ray fluorescence (XRF) on-stream analysers (OSA), gamma density gauges and electromagnetic flowmeters have been developed for the measurement of those variables. Unlike the other variables, stream flow rates could be determined by different ways:"

Jan 1, 2000

By O. Llewellyn Jack

From September 1978 to December 1983, ESD Corporation (formerly a Division of FMC Corporation) undertook the development and testing of a bidirectional auger under contract with the U.S. Department of Energy. Underground testing began in August 1981 at Peabody Coal Company's Marissa Mine near Marissa, Illinois. The auger was developed to increase mine production and coal recovery without increasing land subsidence. It bored 4-foot-diameter by 10-foot-deep holes into pillars on 7-foot centers (each hole recovering 5 tons). All operating during this test was performed by maintenance personnel with the goal of finding ways to increase the machine potential. The maximum excavation rate achieved was 1.4 tons per minute. It was concluded that the concept of drilling short holes to extract coal from underground pillars without surface subsidence was practicable with a wheel mounted auger, but that more power was desirable for this mine, and that the hydraulically driven augering system that provided experimental versatility was not sufficiently reliable for production use.

Jan 1, 1983

By Thomas Leonard, Philip R. Berger, Bryan E. Papillon

Bardon Trimount Inc., a large producer of aggregate, crushed stone, and concrete, was experiencing significant public opposition to its five quarries in the Boston area. It was believed by the authors that this opposition could be significantly lessened if the total number of blasts per week were reduced. Although the blasting company at these quarries, Austin Powder Company, contended that this could easily and safely be accomplished by increasing the size of the blasts, regulations precluded this alternative by limiting the total amount of explosives that could be used per blast.

Jan 1, 1996

By S. Frimpong, S. R. Dindarloo

Material handling in open pit mining accounts for about 50% of production costs. The selection and deployment of efficient, safe, and economic loading and haulage systems is thus critical to the production process. The problems of truck and shovel selection and sizing include determination of the optimal number and capacities of haulage and loading units, as well as their allocation and operational strategies. Critical survey and analysis of the literature has shown that deterministic, stochastic, and experimental approaches to these problems result in considerably different outputs. This paper presents a comprehensive simulation framework for the problem of truck and shovel selection and sizing based on the random processes underlying the network-continuous-discrete event nature of the mining operation. The framework builds on previous research in this field and attempts to address limitations of available methodologies in the form of a comprehensive algorithm. To test the validity of the framework a large open pit mine was evaluated. The stochastic processes governing the uncertainties underlying the material loading and haulage input variables were defined and built into the stochastic model. Discrete event simulation was used to simulate the stochastic model. The proposed model resulted in several modifications to the case study.

Jan 1, 2015

By Jan Pru?ka

This paper describes the sheet pile design for the Line C extension from Ládví station to the North of Prague. The first part of the paper describes the geological conditions and structural configuration of the project. Typical cross sections, the description of the construction stages, and monitoring are discussed. The second part of the paper focuses on the sheeting design method. It describes the method of dependent pressures, that is, how the pressures acting upon a structure depend on the deformation. The design process and verification methodology are described in detail with comparison of the results with in-situ monitoring.

Jan 1, 2011

By G. L. Oldright, Virgil Miller

"This paper is the tenth 4 of a series on smelting in the lead blast furnace, and the fifth 5 on modifications brought about by the introduction of richer charges.ACKNOWLEDGMENTSAll of the data on handling rich charges in lead smelting given in this recent set of five articles describing the results of a cooperative study by the United States Bureau of Mines and the University of Utah were obtained through the courtesy and with the cooperation of the staff of the Bunker Hill & Sullivan Mining & Concentrating Co. at Kellogg, Idaho. The authors acknowledge with appreciation the assistance given by Stanly A. Easton, vice.-president and general manager, F. M. Smith, smelter director, and A. F. Beasley, smelter superintendent, whose generosity, sympathy, and assistance made it possible to obtain this information for the mining industry.GENERAL DISCUSSIONWhen the charge has been dropped into the lead blast furnace, it is out of control of the operator to the extent that, whatever the material is, it must practically all be melted and run out of the blast furnace. The necessary uniformity of mixture to produce slags of regular composition and the choice of the slag—forming ingredients and products to be formed can be made only before the charge to dropped.It was found (R.I. 3096) at Kellogg, where the charge is mostly sinter, that the ratio of the slag—forming ingredients taken from each tuyere was nearly constant, in contrast to the irregular composition of slags taken similarly from a furnace whose charge consisted of ingredients differing greatly in chemical and physical nature, including size. If the charge consists almost entirely of sinter, the blast furnace should then operate more uniformly."

Aug 1, 1932

The molecular structures of isobutyl xanthate (IBX), diisobutyl dithiophosphate (DIBDTP), O-isobutyl-N-ethyl thionocarbamate (IBETC), O-isobutyl-N-ethylcarbonyl thionocarbamate (IBECTC) and O-isobutyl-N-ethylcarbonyl thiourea (IBECTU) were fully optimized using density functional theory (DFT) at the B3LYP/6-31+G(d,p) level with the integral equation formalism for the polarizable continuum model (IEF-PCM) in the aqueous phases. The effects of the polar groups in these thiol molecules on their collecting performances were determined by the energies and compositions of frontier molecular orbitals and the atomic charge values. Our results indicate that the sulfur atom(s) in IBX, DIBDTP, IBETC, IBECTC, or IBECTU molecule is the centre of reactivity. And the collecting abilities of these reagents for copper sulfide minerals follow the order as: IBX > IBECTU ? DIBDTP ? IBECTC > IBETC, and the order of their selectivities against pyrite is suggested as: IBX < DIBDTP < IBETC < IBECTU < IBECTC. The theoretical analysis provides an insight into the collecting powers of these collectors, and offers an atomic scale approach to understand the experimental data available in the literature. Keywords:xanthate; dithiophosphinate; thionocarbamate; thiourea; density functional theory; structure-activity relationship; copper sulfide mineral

Feb 27, 2013

By P. J. N. Pells

A good thing is becoming a bad thing. Rock mass classification systems, that are so excellent for communications between engineers and geologists, and that can be valuable in categorizing project experience, are emasculating engineering geology and rock mechanics. Some engineering geologists have been sucked into thinking that Q and RMR values are all that is needed for engineering purposes, and seem to have put aside what can be learned from structural geology and geomorphology. Many rock mechanics engineers seem to have forgotten the scientific method. This paper attempts to redress the situation by showing how mechanics can be used in rock engineering to design with a similar rigour to that used in the fields of structural engineering, hydraulics and soil mechanics. It also attempts to remind practitioners of what can be achieved by skilled engineering geology.

Jan 1, 2008

By E. Mongilardi

The construction of large underground openings through cohesionless or weak cohesive soils and under the water table in particular, often requires a ground improvement to be done from the surface or ahead of the excavation face in tunnelling problems. To this purpose various injection procedures have been used in the past and new outstanding techniques have been developed recently, such as "jet-grouting", extending the feasibility range. The paper presents a review of basic principles and practical design criteria with particular reference to the newest trends of development. Case histories have been selected within the experience of specialist contractor Rodio Co. showing the variety of problems solved by manifold grouting procedures and layouts, in widely different soils ranging from the sandy-gravelly alluvia of Milan to the soft marine clays of Singapore.

Jan 1, 2010

By Mike Lovitt

New Gold Inc. had commissioned Orica to assist with the design of the drawbell blasting at New Afton Underground copper/gold block cave at Kamloops, British Columbia, Canada. Orica have had much success in developing the single-shot drawbell method at Freeport Indonesia in 2001 in the Deep Ore Zone and they will be using it exclusively in their new Grasberg Underground Operation. RioTinto Northparkes have also used the single shot drawbell blasting in their Second Lift E26 Project and even in the E48 orebody which is a post undercut block cave, realising the safety and operational benefits of this blasting method.

Jan 1, 2013

By G. L. Oldright, F. S. Wartman

"In the process of smelting copper ores and secondaries in the reverberatory furnace to produce a copper matte and a slag low enough in copper content to be discarded on the dump, it is essential to the best functioning of the process that most of the iron in the material charged into the furnace be at the end in the form of sulphide in the matte or ferrous oxide in the slag. Ferric oxide and magnetite present in the charged material should be reduced to ferrous sulphide or oxide. Ferric oxide offers no difficulty in reduction, at least to the magnetite stage, because it reacts very readily with sulphides at quite low temperatures. Magnetite is less reactive and consequently more resistant to slagging, so that the furnace man must take advantage of all factors favoring its reduction in order to prevent accumulations in the furnace.In order to determine these factors more definitely, the Bureau of Mines in cooperation with the Department of Metallurgy, University of Arizona, has undertaken at the Southwest Experiment Station an investigation of the effect of various factors upon the rate of reduction of magnetite by ferrous sulphide. A previous paper's reported the nature of the reactions taking place and the effect of various physical factors when only pure sulphide and oxide were present. Since in the actual smelting operation, many other substances are also present, it seemed desirable to make a study of the effect of their presence upon the rate of reduction of magnetite by ferrous sulphide. Such a study has been made; the work done and the results obtained are described herewith.As will be shown later, it has been found that of the substances usually present in the smelting charge, silica and magnesia accelerate, whereas lime, alumina, and cuprous sulphide hinder the reduction of magnetite by ferrous sulphide.No report of a previous laboratory investigation of this subject has been found. Almost all furnace operators have made at one time or another at least qualitative ccmparisons of the effect of various changes in operating oonditions upon the behavior of magnetite in the furnace, but the conclusions derived from the experiments have never been published."

Mar 1, 1931

By B B. Beamish, J Theiler

Current spontaneous combustion index parameters such as SHT, CPT/RIT and R70 self-heating rate all have deficiencies that need clarifying from a risk management perspective. In some instances they can produce a false negative evaluation and in others they can produce a false positive evaluation. These tests all use a relative rating scheme that does not provide any indication of the time it takes for a spontaneous combustion event to develop, nor do they consider the moderating influence of moisture present in the coal on self-heating rate in the low temperature oxidation region. This is viewed as a major deficiency since the true self-heating behaviour of broken coal is primarily a function of time that is governed by the interaction of the initial boundary conditions (initial ambient temperature and moisture state) with the reactivity of the coal (both intrinsic coal reactivity and accelerated self-heating from reactive pyrite if present). The current index tests are also not appropriate for assessment of coalmine immediate roof and floor rocks.CITATION:Beamish, B B and Theiler, J, 2017. Recognising the deficiencies of current spontaneous combustion propensity index parameters, in Proceedings Australian Mine Vent Conference 2017, pp 113–118 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 28, 2017

By Madgwick J. C

The monosaccharides glucose, galactose and arabinose, and the polyols glycerol and mannitol (0.1 Ufo WIV) supported pure and mixed culture heterotrophic bacterial manganese leaching of solid pyrolusite (MnO2, 2% W/V) to yield 14-38 mg/litre manganous ion in 3 days from a simple mineral salts media at 30&#176;C. Supplementation of pure bacterial isolates growing on glucose with soluble intracellular photosynthate from freshwater algae (0.07 g/l carbohydrate) and marine algae (0.11 g/l) led to an improvement in Mn++ yields of 24 and 100 per cent respectively. Extracellular products of the freshwater algae (0.3 g/l carbohydrate) boosted recoveries by 57 per cent.

Jan 1, 1982

By Marco D. Boscardin

Control and mitigation of building response to construction activities are assuming a greater role in design decisions for underground construction. Alternatives for controlling building response have multiplied with the continued development of ground modification methods, better control of construction activities that cause ground movements, and increased understanding of building behavior and response. This paper describes approaches to estimating building response to construction-related ground displacements caused by adjacent excavation and highlights the discussion with several case history examples. Examples discussed includes experiences with two, seven-story historic structures, supported by timber piles with granite block pile caps, which were underpinned in preparation for ground-freezing ground stabilization and tunnel construction beneath the buildings. The elevation of each building column was monitored and elevation adjustments were actively performed during construction. The second example examines the performance of a slurry wall braced cut, 45 to 50 feet deep penetrating through a stiff crust into a soft clay layer and associated building response. This cut was immediately adjacent to two, approximately 15-story office buildings, which were supported by deep foundations founded in the stiff crust.

Jan 1, 2003

By Lynch A. J

Comminution within rod mills has been investigated by use of a matrix analysis of breakage processes. A parameter, the number of breakage stages, has been introduced and comminution within all rod mills has been expressed in terms of the number of grinding stages and a function which describes the feed rate, mill diameter, and mill speed. The effect of variation in feed rate, feed sizing analysis and mill speed on the number of breakage stages is discussed, but no general relation is proposed because more study is needed.INTRODUCTIONRod mills are normally used as the first unit of multi-unit systems for the grinding of metalliferous ores and the cost of operating rod mills may be considerable. For both economic and metallurgical reasons, it is therefore necessary that the mills should be operated efficiently and that a knowledge of the mechanism of the size reduction process within rod mills should be as complete as possible. While a qualitative assessment of the process may be of some value, a quantitative assessment gained by describing the process in mathematical terms can be of much greater use because it may also be used for design and control purposes.In this paper, an empirical mathematical model is postulated to describe the size reduction process within rod mills and it is used to analyse the effects of variations in both rates and size distributions of the feed to the mills.GRINDING CHARACTERISTICS OF ROD MILLSMyers (1953) discussed the grinding characteristics of rod mills and suggested that a pronounced screening effect, resulting in the preferential grinding of the coarser particles, occurs within the mills. This is illustrated in...

Jan 1, 1964

By J. F. T. Agapito, R. R. Goodrich

Yield pillars have been used for many years to help reduce stresses near mine openings and improve roof and floor stability. A yield pillar is often defined as a pillar that fails but retains residual strength. Stress transfer occurs through the roof and floor after the peak strength of the pillar is reached. High stresses are transferred from around the openings onto abutments that can be barrier pillars or unmined ground. This mechanism, often referred to as pressure arching, is possible as long as the width of yield pillars is less than the critical width above which stresses cannot be carried by the overburden. Significant stress transfer also can occur due to small amounts of pillar and/or floor yielding before the peak strength is reached. This is accomplished in a quasi-elastic manner with little or no visible roof and pillar fracturing or floor heave. Long-term stability may be achieved when stresses and mechanical properties are favorable to pre-failure yielding. This paper gives practical examples where improvements in stability and resource recovery were achieved with this mechanism. Yielding was assessed by comparing measured and calculated vertical pillar stresses. Results indicated that calculated stresses in the pillars were 25 to 40 percent higher than the measured stresses, demonstrating significant arching load transfer to the abutments. Pre-failure yielding is probably often present but unintentional in both development and production areas. Better recognition and use of this mechanism should lead to improved designs as mines become deeper.

Jan 1, 2001

By W. William Culver

James Douglas became known in the nineteenth century for two reasons fundamental to his mining career: (1) his experimental work with copper hydrometallurgy, and (2) his grasp of the idea that the quantity of copper ore matters more than the quality. On the first reason, there is a moment for any technology that’s critically important—when it moves from an area of scientific interest to one that companies are founded on. This paper examines the original 1869 Hunt and Douglas Copper Process in the context of science and engineering as they were in the 1860 and 1870s. It was a “humid” process, developed at Quebec’s Harvey Hill Mine. Chemically, the Hunt and Douglas vat leaching process succeeded, but not the original companies using it. On Douglas’ understanding of ore quality versus quantity, luck had it that the first company to field test the Hunt and Douglas Copper Process was in Chile. The Hunt and Douglas patent made that transition from experimental model to operational plant in 1870 when the Compañia de Minas de la Invernada was organized in Valparaíso. As a joint-stock company, Invernada spread the risk of investing in the revolutionary, but untested, Hunt and Douglas Process. The company brought Douglas to Chile as a consultant in 1871. His experience with hydrometallurgy, combined with what he learned about the copper business while in Chile, set him off on a career in metal mining that both surprised Douglas and made him wealthy.

By Li Keqiang

Among the pile foundations of the 156 tall buildings over 18 storeys in Shenzhen, 86. 5% of them are constructed by slurry drilled piles, bored piles and excavated piles (hand-dug caissons). Based on the experiences of the engineering practices, the paper points out that the main quality problems of pile foundations in Shenzhen are: insufficient bearing capacity of single pile; poor concrete quality of pile; damage of the precast pile; pile tip not reaching the required bearing stratum and the thickness of bored/drilled sediment exceeding the specified. etc. The quality inspection methods that have been used include: check of construction records and excavating; static loading test; core sampling test; non-destructive test, etc. Treatments of quality problems used in Shenzhen are also introduced in this paper.

Jan 1, 1991