Search Documents

Two coal seams were selected and the conceptual designs were based on the geological and physical conditions typical of these seams. As a result of the screening process presented below, the two coal seams selected were the Lower Kittanning Seam in central Cambria County, Pennsylvania and the Pittsburgh Seam in northwestern West Virginia and southwestern Pennsylvania. SELECTION PROCESS FIRST SCREENING OF LONGWALL OPERATIONS The list of longwall operations prepared in Phase I and included in the Phase I report, was used as the basis for a first screening. From this list it was determined which longwall operations were not in the Appalachian coal fields and not in a coal seam of the thickness range of 42 to 72 inches. The first screening eliminated 30 of the listed operations, leaving 48.

Jan 1, 1976

By K. L. Paciorek

Organic materials utilized as cable Jacketing, cable insulation, standoffs, insulating boards and potting compositions were identified and d literature survey performed to obtain the required thermal oxidative and moist tracking data. Thirty representative compositions were procured and subjected to thermal and moist tracking evaluations. Tracking was found to invariably result in ignition or glow of the test specimen. Influence of parameters such as electrolyte strength and composition, temperature, conductor spacing, and electrode material were investigated. Volatile s produced by selected insulators on thermal oxidative and electrical stress were identified, quantitated, and their potential impairment action upon a current interrupter assessed.

Jan 1, 1980

By Milne J. Schmid

A program has been conducted to determine the feasibility of providing a borehole liner for Kelly Bar drilled boreholes in Southern Florida. The concept was to drill the borehole with the Kelly Bar and with it still in the borehole insert a tube which would remain in the unstable ground after withdrawl of the bar. The tube then will provide an unobstructed borehole for the charging of explosives upon completion of the drilling the shot pattern.

Jan 1, 1977

By Brown H. R, Wright E. A

The authors identify the workable coal seams, their distribution in relation to quality and economic occurrence and relate their analytical characteristics to industrial use. The development of established collieries is also discussed with regard to increased production demand.The authors also indicate the potential of the coal resources of the Southern District and postulate their ultimate development.INTRODUCTIONThe Southern Coalfield yields 30 per cent of the total production of bituminous coal in New South Wales. The economic potential of the coalfield was examined last by Harper (1915). Since that time additional knowledge has been gained by prospectors, mining companies and public authorities. Expansion in the steel industry and the building of power stations on the coalfields together with improvements in fuel technology, mining methops and road transport have resulted in production of coal from seams mice thoughtto have no economic value.DESCRIPTION OF THE COALFIELDFor the purpose of this paper the term Southern Coalfield includes also the South-Western Coalfield which together comprise the following Coal Districts:IllawarraDouglas ParkWollondilly-NattaiMoss Vale-Berrima (Hanlon, 1953).Geographically the coalfield is contained by the Illawarra Range in the east, the Shoalhaven River to the south, the Wollondilly River to the west, and in the north by a line...

Jan 1, 1958

By Dave Bigby

Hatworth Colliery, operated by RJB Mining (UK) Ltd, is successfully mining the Deep Soft Seam at a depth of 1000m using single face retreat longwalling. The seam is characterised by a weak roof generally comprising 4 to 6m of well bedded carbonaceous mudstones overlain by weak siltstones. The paper describes the layout and support design strategies which have enabled the colliery to adopt sole support by rock reinforcement techniques for its longwall gateroads. To achieve this success the colliery layout has had to be radically modified to take account of the in-situ horizontal stress field. The layout is also closely controlled by environmental considerations, the seam being one of the gassiest in the UK Economic support by strata reinforcement has been achieved using a combination of rockbolting of the roof and sides installed at the face of the heading, and systematic double birdcage cable bolting installed on drivage and supplemented ahead of the retreating panel. The layout and support strategies have been developed through a combination of detailed underground measurement of support and stress parameters backed up by numerical modelling using FLAC. The FLAC modelling has paid particular attention to careful representation of bedding properties and validation through underground stress measurement.

Jan 1, 1996

By C. F. McCarroll

The effectiveness of an industry?s safety activities can be gaged best by the accident records of that industry. In an effort to gage conditions in the petroleum industry, and with the objective of helping to reduce the number of accidents in it, the Bureau of Mines from time to time has tabulated, analyzed, and published pertinent statistical information3/. These reports have dealt with distribution, causes, and costs and related phases of accidents for various and collective divisions of the petroleum industry in several sections of the country. This type of study aids the personnel of the Bureau in planning the course of its activities in accident-prevention work and gives useful data to persons engaged or interested in the promotion of safety in the petroleum industry, which will aid them in their efforts to reduce the number and severity of accidents. A majority of petroleum operators and ?service" contractors have acknowledged their responsibility to provide their employees with safe working conditions and to their stockholders for greater economic value of invested capital by establishing safety divisions within their respective organizations. Such divisions have a primary duty, namely, to see that properly designed and guarded machinery and working equipment are furnished the employees and that they are trained in the safest practical methods of performing their work. Some companies and individual operators, however, have shown little or

Jan 1, 1939

By P. R. Jones

A computer program was written for the design of a shell and tube type heat exchanger on a price optimum basis. The program was designed to meet the following requirements: (1) Triangular pitch; (2) single or multiple pass; (3) heating or cooling; and (4) no change in phase. Price optimum design was obtained for four standard tube sizes and standard pitch. Pressure drop both inside and outside were computed and the nearest standard shells having at least the required area were listed. With this information, the estimator can select the heat exchanger best suited for the need. The program was made adaptable to various fluids and to various tube sizes and spacing by reading in much of the required data such as physical properties of the fluids, tube data, and standard shell data in tabular form.

Jan 1, 1967

By David C. Uhrin

Two improved methods have been developed to transfer microfilmed mine maps to suitable base maps showing surface features. The methods provide for (1) positioning and orienting maps; (2) merging adjacent maps; and (3) plotting maps at a common scale. One method produces an overlay mosaic of mine maps using an Integrated camera-processor. This photographic method shows the details of mine workings and is most useful for specific limited-area projects. In the second method, outlines of mine maps are digitized, manipulated, and plotted as overlays using a computer. This computer method can plot mine outlines and spatially index large numbers of microfilmed maps. Microfilmed mine maps used in this Bureau of Mines study are on file in the Mine Map Repository of the Eastern Field Operations Center. The base maps are U.S. Geological Survey 7.5-minute topographic maps. The demonstration area is located in the New Kensington East and West quadrangles, Pennsylvania.

Jan 1, 1977

By R. N. Hambright

Gaseous and particulate exhaust emissions are characterized for a 1200 Bhp two-stroke cycle diesel, a 1000 Bhp four-stroke cycle pre-combustion chamber diesel, and a 900 Blip four-stroke cycle, direct injection diesel using steady-state modal testing and a versatile exhaust dilution-collection system. In addition, a 1.50 Bhp four-stroke cycle, pre-combustion chamber, turbocharged diesel was characterized for use in experimental water injection evaluations. Water injection downstream of the turbocharger compressor and upstream of the turbocharger exhaust turbine are evaluated for their particulate removal effectiveness on the small turbocharged diesel engine. The water droplets are inertially separated using cyclone separators designed for minimum pressure drop and outsize, lip to 50 percent of the total particulate mass generated was removed using a combination of both inlet and exhaust water injection techniques.

Jan 1, 1981

By S. Al-Thyabat

Conditioning of flotation feed is an important prerequisite for efficient flotation. This process depends on parameters such as conditioning time, slurry concentration and slurry pH. The objective of this paper is to optimize the conditioning process for the flotation feed. This was achieved by first conducting preliminary experiments at constant slurry pH to determine the significant ranges of slurry concentration and conditioning time. Then, factorial experimental design (32 experiments) was used to investigate the significance of the above parameters and their interactions on flotation recovery and grade. Statistical analyses using ANOVA approach showed that flotation recovery (R) and concentrate grade (g) were affected by feed conditioning. It was found that concentrate grade was linearly proportional to the slurry concentration and conditioning time, while flotation recovery was exponentially proportional to the conditioning parameters. A contour plot of the flotation response (recovery and grade) against conditioning parameters showed that the optimum operating parameters for flotation feed conditioning was a conditioning time of 1.5 to 2 minutes and a slurry conentration of 55% to 60%.

Jan 1, 2008

By S. L. Gerhard

In the United States the performance characteristics of permissible explosives are controlled by routine tests, which include firing the explosive into a gallery filled with a methane-air mixture. These tests are made by the staff-of the Explosives Division of the Bureau of Mines and are similar, in general, to those employed in other countries. This control has helped to reduce the frequency of accidents involving the ignition of firedamp by explosives but has not clarified the basic causes of the ignition. To advance this control and to minimize potential hazards further, this fundamental knowledge is needed. Some of the results of recent research on the causes of the ignition are described herein. NATURE OF THE PROBLEM When an explosive ignites firedamp in the gallery tests, the source of the ignition must be one or more of the emissions from the steel borehole. It has been accepted generally that these emissions are (1) particles, (2) the shock wave, and (3) hot gases and flames. Photographs show that the shock wave emerges from the borehole first, followed closely by hot gases. At first the velocities of these are high and approximately equal, but the velocity of the gases decreases more rapidly than that of the shock wave, and by the time the reactions causing the flame are complete the shock wave travels in an otherwise undisturbed medium. The particles are originally enveloped in the hot gases but some soon begin to break through and eventually out-distance the shock wave. The approximate geometry of these emissions about 1 millisecond after the shot is fired is illustrated in figure

Jan 1, 1939

By Patrick Bermingham

This report presents the results of six STATNAMIC loading tests that were carried out on four different pile types at the CALTRANS 280 Test Site (Bridge No. 34-46) in conjunction with the Tension Pile Test Program. The STATNAMIC testing was performed by Berminghammer Corporation at the request of the California Department of Transportation, Office of Geotechnical Engineering. Others performed the static tension (uplift) and compression loading tests which werecarried out on the piles tested using the STATNAMIC method. A summary of the STATNAMIC test results is presented and discussed, and the appropriate results are compared with the static test results

Jan 1, 1993

By Wesley, Worner H

During the meeting of the Institute last year at Port Pirie, the opportunity was taken to sample the lead bullion coming from the blast furnace and various stages during the refining process. Also, in the desilverising section, the upper zinc rich phase was sampled as the silver content built up and in the cupellation operation a series of samples was taken as the silver content of the bullion increased. In these two cases, the samples were taken under the supervision of a member of the staff of the Broken Hill AssociatedSmelters.In the following account of the microstructure of the samples taken, only the main phases present have received attention. In this connection deduction from phase diagrams of binary alloys has been used in conjunction with the assays carried out on duplicate samples taken at the same time as those for micro examination.

Jan 1, 1938

Choosing the correct delay time for many blasting applications is an important and critical blast design parameter for controlling fragmentation, muckpile shape, swell, digability, throw, ground vibration and airblast. BAl and its affiliates have monitored thousands of full scale blasts in a variety of field conditions, spanning over 15 countries, with sophisticated blast monitoring instrumentation. In some blast environments, a small change in the choice of delay times used had a dramatic and pronounced effect on the overall blast results. In other blast environments, large changes in the choice of delays used had absolutely no effect on the final results in terms of specific outputs. In environments which were sensitive to the delay selection, the type of explosive, dynamic response time of the rock mass (TMIN), integrity of the material, burden and rock mass geometry, all played a very important ,role.

Jan 1, 1998

By Robert A. Jankowski, J. Drew Potts

In this U.S. Bureau of Mines study, four underground respirable dust surveys were conducted to determine factors affecting belt entry dust levels and how using belt air to ventilate work areas affected dust exposures. Belt entry dust levels on the surveyed longwall and continuous miner sections averaged 0.59 and 0.26 mg/m3, respectively. The stageloader-crusher contributed an additional 0.5 to 0.9 mg/m3 of dust to belt air, while the feeder-breaker contributed 0 to 0.2 mg/m3 of dust. A 1,000-ft increase in belt entry length or a 200- to 500-st-per-shift increase in production resulted in roughly a 0.1-mg/m3 increase in dust. Using the belt entry as an intake entry on the continuous miner section appeared to reduce dust levels by 0.1 to 0.3 mg/m3 during cutting. Belt air was not used to ventilate the face on the longwall section.

Jan 1, 1992

By Michael Stanwood

Project feasibility no longer involves just technical and economic viability-today's feasibility study must include environmental, regulatory, and political considerations as well. While the US now appears at least somewhat committed to developing synthetic fuels, including oil shale, it is the environmental issues, rules, regulations, and guidelines that will play the major role in determining the timing, magnitude, and overall scope of synfuel development in the coming years. The key environmental obstacle affecting oil shale development is uncertainty. Although oil shale may be the most environmentally studied "new" technology in the world, little is known with much degree of certainty about potential environmental consequences of one full-scale commercial facility, or the effects of a massive development effort in a relatively pristine and sparsely populated area. Other primary environmental uncertainties include: • Environmental compliance costs and their effects on investment decisions; • The reliability and acceptability of anticipated pollution control technologies; and • The confusing, time-consuming environmental regulatory framework, which requires more than 100 permits, clearances, and reviews before development occurs. This discussion will focus on the latter uncertainty, and will describe he current status of potential constraints to oil shale industry development in five areas: water availability; water quality degradation; air quality degradation; reclamation and spent shale disposal; and community impacts.

Jan 1, 1981

By H Thanasekaran, J Kohmuench, B Seaman

To achieve an efficient separation in the flotation process, valuable particles need to be selectively segregated from the gangue while utilising a minimum number of flotation stages. TodayÆs existing flotation technologies are effective for fine particle size classes; however, limitations due to particle buoyancy and bubble-particle detachment restrict the effectiveness of traditional flotation approaches on coarser particles. As a result, flotation circuits are generally configured to process only fine particle size classes in order to maximise recovery in the primary stages. Eriez has invented a novel flotation technology, the HydroFloat, which overcomes these limitations by carrying-out flotation in a dense, fluidised-bed medium allowing for the recovery of coarse particles (>0.250 mm). Over the last 15 years, this technology has been successfully applied to industrial minerals with several full-scale units installed to recover particles up to and exceeding 3 mm diameter in primary flotation circuits. This paper includes discussions on the history of this technology, process theory, existing applications, and a review of recent sulphide-based laboratory test work conducted for Newcrest mining and others. Benefits of this approach, such as improved recovery, low energy consumption and reduced reagent addition will also be reviewed.CITATION:Kohmuench, J, Thanasekaran, H and Seaman, B, 2013. Advances in coarse particle flotation - Copper and gold, in Proceedings MetPlant 2013 , pp 378-386 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 15, 2013

By David Conover

The El Boleo Copper Project is currently in the final design stages for development of a 3-MM-tonne/yr underground copper mine located in Baja California, Mexico. The nearly horizontal mineralized zones are amenable to exploitation by conventional mechanized coal mining technology using continuous miners, shuttle cars, and belt haulage. The mine design resembles a typical full-extraction coal mining operation utilizing a sequence of mains, sub-mains and production panels. Due to numerous faults, mining will be conducted as several small adjacent mines accessed through adits from large arroyos cutting through the mine area. Up to four seams may be mined in some areas with a maximum overburden depth of about 250 m. The ore zone is relatively weak and plastic, subject to extensive creep over time. The mine workings will pass through areas of historical shortwall mining panels where the ground has flowed into old entries and gob areas, and then reconsolidated. A small test mine was developed to evaluate mechanical cutting performance, roof-bolt anchorage capacities, roof and pillar stability and caving behavior. In-mine measurements were combined with two- and three-dimensional FLAC models to evaluate alternative development and production pillar designs. The paper will discuss the various factors influencing ground stability at the El Boleo project and the strategies employed in developing a suitable ground control design.

Jan 1, 2009

By Fred V. Carrillo

Of the total quantity of secondary copper and zinc that became obsolete in the United States from 19b1 through 1970, more than 11 million tons of copper and 10 million tons of zinc were not recovered. These estimates are based on a study of the flow and recovery of old copper and zinc scrap by consumption end-use. This report describes (1) where copper and zinc are being used; (2) when they become obsolete and available as secondary metal; (3) how they are being collected for recycling; and (4) how much might be recovered from scrap that presently is not being recycled.

Jan 1, 1974

The works recorded in this Test Report have been performed by Rade Roncar - Electrotechnical Institute of Zagreb, SFR Yugoslavia in collaboration with Bureau of Mines. The main objective of these investigations was to investigate the possibility of fabrication of thin-walled square enclosures of satisfactory safety factor in accordance with requirements of effective technical regulations. The results and the investigations can be divided in three main fields: - investigations of thin-walled enclosures with the view of determination of pressures causing technological deformations before performing tests in accordance with effective applicable regulations, - finding the safety factor by means of tests of metal-foam pressure vents, - comparison of enclosures with and without pretreatment by technological deformation.

Jan 1, 1987