Search Documents

By P. H. Reynolds, S. Liaghat, A. Zarasvandi

"Darreh-Zerreshk and Ali-Abad are two relatively small porphyry copper-type deposits in Yazd Province in central Iran. They are located within the central Iranian volcano-plutonic belt, formed above the collisional convergent margin of the Iranian lithospheric plate from the late Eocene to the Miocene. This paper discusses the geochemical characteristics of the igneous rocks, and 40Ar/39Ar geochronology of plutons and alteration phases associated with the Darreh-Zerreshk and Ali-Abad deposits. The deposits are spatially associated with igneous complexes that consist of older and barren granites intruded by intermediate-composition granitoids, which are the carriers of Cu mineralization. The granites have relatively high content of Nb, Y, and K, a prominent negative Eu anomaly, and were probably derived from melting of, or contamination of mantle-derived magmas by, continental crust. Porphyritic diorites, quartz monzodiorites, and granodiorites show enrichment in light rare earth and large-ion lithophile elements, depletion in middle rare earth elements, and have no negative Eu anomaly. These intermediate-composition granitoids were derived from melting of the upper mantle or lower crust, and their differentiation was controlled partly by fractionation of hornblende. A pilot K/Ar whole-rock dating study suggests that the pre-ore granites were emplaced in the Oligocene. Dating by the 40Ar/39Ar method of nine samples of secondary biotite and sericitized rocks from drillcore within the mineralized and altered zones in both deposits yielded a well-defined age of ca. 16 Ma. This date is interpreted to be the time of hydrothermal alteration and of porphyry copper type mineralization in this part of Iran."

Jan 1, 2007

By Braden Lusk, Paul Sainato, Josh Calnan, Hiago Vasconcelos, Luis Felipe Marinho

"Blasting and rock fragmentation is one the most important unit operations in mining. Since itsintroduction into the mine production cycle, mining has become more efficient in mineral production(Hartman, 2002). Widely used with the main objective of breaking rock mass in smaller fragments to be loaded and hauled at a minimum cost, blasting is optimized when stemming materials properly confine drillholes charged with explosives. Halim Cevizci (2013) performed a stemming application using Gypsum plaster, a kind of material that exhibits solid-like behavior when it is dry. Based on his theory, the present article reports an experiment using another type of material that shows similar behavior, non-Newtonian fluids. The primary goal of this study is to measure the confinement effectiveness provided by a non-Newtonian mixture as the stemming component. The study also analyzes the explosives’ energy propagation throughout the rock mass relating to the stemming materials applied. Currently, mining literature recommends the application of dry granular materials in stemming columns, because of its inertial and high frictional effects (Hagan, 1973). However, the test verified that the mixture added to the stemming column was able to reduce energy and gas losses to the atmosphere, because of the liquid’s property of filling voids in the material. The solid-like behavior of the non-Newtonian mixture was investigated for its capability to improve borehole confinement, since the mixture reacts like a solid when under shear stress. The results were compared to those from sand and air stemming applications, configured in different arrangements. It was concluded that the non-Newtonian mixture yielded high results due to its better confinement effectiveness, a reduction of air overpressure, and an increase of the strain propagation and ground vibration throughout the rock."

Jan 1, 2016

By Alexander Filotti, Stanley Merjan

"Abstract. The paper shows the benefits and accomplishments of this relatively new but established product on the pile foundations market in the United States. The first part of the paper describes general aspects of the design, construction, and geotechnical capacity (designed and in situ) of Tapertube piles. The qualities resulting from the design and manufacturing of the Tapertube pile will be presented first.The second part of the paper describes the installation of Tapertube piles for an addition to Terminal One at JFK International Airport and The Edge development. A carbon print analysis for both projects is developed using the EFFC-DFI carbon print calculator. For the JFK project the benefits of using BIM in redesigning the project for Tapertube piles are explored.General description.The tapertube pile consists of a tapered tubular bottom section attached to a conventional pipe extension. The 50 ksi steel for the taper is mechanically folded into a polygonal cross-section (usually 12-sided) with a longitudinal welded seam. The tapers are fabricated in many sizes with bottom diameters varying from 8 to 14 inches, top diameters from 12 to 20 inches, lengths from 10 to 35 feet, and steel thicknesses from 3/16 to 1/2 inch. A conical steel shoe or a flat plate is welded to the bottom of the taper and the top of the taper is circularized to match the outside diameter of the pipe extension. The inclination of the tapers is generally between 1.5% and 2.5%.The pipe extension is fully butt welded to the taper and has the necessary length for the pile to develop the requisite capacity. Concrete fill for the piles is generally 4,000 p.s.i. or more. Typically the piles are shopassembled and shipped to jobsites in lengths to 80 feet."

Jan 1, 2014

By M. A. Reyes, L. Yan

Heat and humidity buildup within refuge alternatives (RAs) may expose occupants to physiological hazards such as heat stress. The Mine Safety and Health Administration (MSHA) regulations require RAs in underground coal mines to provide a life-sustaining environment for miners trapped underground when escape is impossible. RAs are required to sustain life for 96 h while maintaining an apparent temperature (AT) below 95 °F (35 °C). The National Institute for Occupational Safety and Health (NIOSH) tested a 10-person tent-type RA, a 23-person tent-type RA, and a 6-person metal-type RA in its underground coal mine facilities to investigate the thermal environment over a 96-h period. The test results showed that mine air and mine strata temperatures surrounding an RA occupied by simulated miners (SMs) increased over the 96-h test period. The test results suggest that RA manufacturers should consider this increase in temperatures when calculating and evaluating RA components during surface and laboratory tests. The findings can equip stakeholders with additional considerations for calculating the interior heat and humidity temperature profiles for occupied RAs not tested in situ

Nov 22, 2019

Diesel Particulate Matter (DPM) is considered carcinogenic after prolonged exposure. With increasing use of diesel-powered mining equipment in underground mines, miner?s exposure to DPM has been increasing. Most studies on the issue has been DPM control measures with few studies on diesel exhaust propagation patterns after leaving the tailpipes. This study uses computational fluid dynamics (CFD) to investigate the airflow pattern in an underground metal/nonmetal mine for a single heading. Several high DPM concentration areas are identified in the study and common practices for compliance are suggested. Airflow and DPM distribution are compared between blowing and exhausting face ventilation systems. Suggestions are also provided for the protection of miners in the face area.

Jan 1, 2009

By Alexander J. Verstraeten

The design and construction of foundations for power transmission line towers present some special problems. This paper describes a system of design and construction for these foundations that was developed in Europe and has attained general use there because of its reliability and cost effectiveness. Transmission line foundations distinguish themselves by having to deal not only with compressive and lateral loads, but with uplift loads and, because of the wind (in some regions earthquakes), with dynamic loading. The construction of transmission line foundations distinguishes itself mainly in the great number of inaccesible locations involved, resulting in extensive geotechnical investigation and logistical problems in moving men, materials and equipment.

Jan 1, 1987

This paper describes the behaviour, under creep conditions, of a cast lead creep specimen consisting of five crystals, the boundaries of these crystals being substantially at right angles to the direction' of tension, i.e., across the long axis of the specimen. This particular specimen was obtained in an attempt to produce a single crystal in the manner described in the appendix of a previous paper (1).Thus, the specimen was of the same shape and size, was composed of the same purity lead and received the same preliminary treatment as the single crystal test-pieces.The object of the experiment was mainly to observe the effect of the crystal boundaries on both the deformation of the test piece and the process of recrystallisation and to compare the creep rate of the test-piece with that of a specimen consisting of one crystal only.EXPERIMENTAL METHODThe specimen had an effective test length of 10 cms. and a cross $ection of 0·5 in. x 0·25 in. In Fig. 1 is given a sketch of the specimen to scale showing the positions of the crystal boundaries on all four surfaces. Except for those of crystal No. 4, which was confined to approximately one-half the cross section of the specimen, the boundaries of each crystal traversed the four faces.The specimen was mounted in exactly the same manner as the single crystal specimens. During the creep test, it...

Jan 1, 1941

By Dimitri Frantzos, Stewart Thompson, Ed Skiba, Hans Tammemagi

On behalf of Acres International we would like to thank Frank Chiappetta of Blasting Analysis International for inviting our organization to participate in this state-of-the-art course on blasting analysis techniques.

Jan 1, 1989

By Robert N. Roby

This report is one of a series based upon investigations made and being made within the Missouri River Basin in Montana by engineers of the Bureau of Mines , Albany Branch , Mining Division . These investigations are made primarily to provide preliminary information to Department of Interior agencies and others concerned with the planning of the proposed Federal power developments within the Missouri River Basin . The present report has been designed to permit public distribution of the factual data obtained . The field investigations in Meagher County were made during tually all 1948 ; Vir- known metallic mineral occurrences within the county were investigated ; some nonmetallic mineral deposits also were investigated . The investigations cannot be considered complete , however , because some long-inactive mines or prospects may have been missed . Most of the old mine and prospect openings are caved; many are completely inaccessible . Many of the claims located years ago have been abandoned ; others have been relocated under different names and ownerships . Because of such conditions , much of the information regarding their development and operation necessarily has been obtained from Federal and State publications , supplemented by information provided by owners and local residents .

Jan 1, 1950

At the Orieco mine quartz veins carrying sulphides were localized in parts of an extensive fault zone in the Mathinna Beds during late Middle Palaeozoic mineralization.These deposits were subsequently exposed, and oxidation of the sulphides by percolating groundwaters resulted in the formation of gossans at the surface, and replacement close to the permanent water table of the more soluble sulphides by copper sulphides (chalcocite, coveIlite). A restricted zone containing copper oxides (cuprite, tenorite), copper carbonates (malachite, azurite), iron arsenates (scorodite, pharmacosiderite) and possibly rare copper sulphates occurred above the water table.The renewed oxidation of these deposits following mine development has been facilitated by the ready circulation of air and water combined with the formation of large free surfaces ideal for evaporation of aqueous solutions. Under these new conditions of high initial sulphate concentration, low pH, and relatively high Eh, the previously formed mineral assemblage is unstable and numerous Cu (Fe,Zn)-sulphates and Fe (Cu,Pb)-arsenates are presently forming in fractures in the fault zone and on the adit and stope surfaces for some considerable distance from the Sulphide-rich ore shoots. The observed spatial sequence of the major sulphates with respect to the sulphide-rich zones (Le. chalcanthite-antleritebrochantite and langite) is consistent with decreasing sulphate concentration and increasing pH away from the oxidizing sulphides.

Jan 1, 1970

By Fritz J. Klingler

From site demolition, to design, to construction, Detroit's new Tiger Stadium project is required to be completed within a short 2 ½ years from award of the design-build contract. Such extreme schedule requirements together with somewhat difficult ground conditions at the site, resulted in several challenges in the design and construction of the deep foundation system for the stadium. During the geotechnical investigation, an intermittent water bearing sand layer was encountered overlying the hardpan at the site. As a result, some concern developed regarding the potential for collapse of caisson bells within this layer, as well as the potential for flooding of the caissons during drilling. Although sand and/or ground water was encountered within about half of the caissons, standard drilling and belling methods were used, and adverse conditions were controlled in almost all cases through expeditious drilling, inspection and concreting of the caissons. This paper will present a summary of the ground conditions, design and specification requirements, and construction methods used to successfully install the caissons for this project.

Jan 1, 1999

By R. F. Randolph, R. S. Fowkes, J. J. McClelland, G. H. Schnakenberg

Between 1986 and 1992, there were268 deaths and 54,642 severe injuries to workers in underground U. S. mining operations. Clearly, this level of health and safety risk is not acceptable. While most underground coal mining jobs are dangerous, some are much more dangerous than others. Many jobs in an underground coal mine are clustered around the working face—the place where machinery digs coal from the surrounding rock. The hazards in this area are numerous: When the coal is removed, the ground around it becomes unstable and can cave in on the workers. The mining machines used there are large, heavy, powerful, and move in many different directions in a very confined space, presenting danger to workers. Also, the machines churn up coal dust that causes black lung and other ailments. Figure1 shows a modern radio remote controlled continuous mining machine and its operator. In a typical mine, the jobs with the greatest exposure to hazards involve operation of machinery that cuts tunnel-like passages into the coal (the continuous mining machine) and machines that insert supportive steel bolts into the rock above the work area (roof bolting machines). The workers who endure these hazards are at almost twice the risk of death or disabling injury than co-workers in other safer areas of the mine. Of the statistics quoted above, 106 of the 268 deaths and 21,552 of the 54,642 severe injuries occurred in jobs involving equipment at the working face. The operators of roof bolting and continuous mining machines account for only 21% of the work force but suffered 40% of the deaths and 39% of the lost-time injuries during1986-1992. These death and injury rates are almost twice the rate for workers in other underground mining jobs (see figure 2). The estimated total cost of the 106 fatalities and21,552 lost-time injuries was $327 million from 1986-1992. On average, each fatality cost over $1 million and each lost-time injury costs in excess of $9,000.

Jan 1, 1994

By Fookes R. A, Gardner K. J, Gravitis V. L, Watt J. S, Steffner E. J

Two radioisotope techniques suitable for the rapid laboratory determination of the ash content of coal have been tested ou unwashed coal samples from four Australian coal seams. In one techniqne, measurements of backscattered 238Pu L X-rays and iron K X-rays from finely ground coal samples have been combined to determine ash content in uuwashed coals to ±0.5 weight per ce111 ash (ls) for three seams and 0.9 weight per cent ash for the fourth.The second technique, which involves measurements of the transmission by the coal of narrow beams of 241Am 60 keV and 123Ba 356 keV ? rays, requires less sample preparat ion. The ash was determined to within the range of 0.8 to 2.6 weight per cent for the four seams (unwashed coal). For washed coals, errors are expected to be < ±0.5 weight per cent ash.

Jan 1, 1982

By L. Ross Weber

Gentlemen and guests of the Rocky Mountain Coal Mining Institute: This is the thirty-second regular meeting of our Institute, and rather than try to make some extemporaneous remarks, I thought it best to write them out, so I could in that way give them to you, and probably give you a new thought for the future conduct of our Institute. The thirty-first regular meeting of the Rocky Mountain Coal Mining Institute was held in Salt Lake City, June 22, 23, and 24, 1932, and due to rapidly changing conditions in the coal industry, subsequent meetings have been postponed from time to time, as many of our members and our Secretary have been tied up with code and labor matters. Since our last meeting, at which was discussed problems of vital interest to all of us, especially the production and marketing of coal safely and economically, and the stabilization of our industry, which has already suffered two years of deplorable conditions, almost two more years have been added to the record, but during the past six months miracles have happened, and an industry which formerly was unable to govern itself, has now, through the aid of our Government, at least learned how to make a proper start in that direction. Whether we like it or not, and whether or not the things being done are in agreement with our various political beliefs, without doubt, we are in a much better position today than prior to this transformation. However, it is a pleasure to all of us to note that safety has not been lost sight of in the interim, and without doubt, as later papers and statistics will substantiate, the period since our last regular meeting has probably shown the most remarkable safety achievement of any period in recent history.

Jan 1, 1934

By Davy A. T, Hansen J. O

The causes of ferrosilicon loss from Dense Media Separation (DMS) plants, and the related properties of ferrosilicon, are identified. Two characteristics, corrosion resistance and saturation magnetisation, are examined in detail. The chemistry of the corrosion mechanism is described and its relationship to plant parameters discussed. Methods of reducing corrosion losses are proposed. Lack of particle homogeneity, and its influence on corrosion and abrasion is noted. The relationship between low magnetic susceptibility-and increased magnetic separator losses is demonstrated experimentally.

Jan 1, 1986

By Chuanlin Fan

The process of flotation separation and recycling of spent potlining (SPL) was described. On the basis of the laboratory investigations, the effects of influencing factors in froth flotation process, such as grain size, flotation agent dosage, pH value, pulp density, and dissolved components concentration, etc, were carefully studied. And the influence on environment of the process was also discussed. It was found that flotation separation can be used as an environment-friendly method for treatment of SPL residue. Carbon and other compounds (include cryolite, sodium fluoride, calcium fluoride and diaoyudaonite, etc.) from SPL were separated and recycled as flotation products respectively.

Jan 1, 2009

By Juan M. Antorena

A pile driving and testing program was undertaken to evaluate installation procedures, assess capacity, particularly in uplift, of 360- and 460-mm (14- and 18-inch) square prestressed concrete piles and provide foundation design parameters for the New Mid-Point Bridge project in Fort Myers, Florida. Nine piles were dynamically monitored during installation, and six piles were monitored during restrike driving to evaluate pile drivability and uplift and bearing capacity including time related capacity increases due to soil "set-up". In addition, two static load tests (tension and compression) were performed to calibrated the results obtain during the dynamic testing. This paper presents descriptions of the pile driving testing program along with findings regarding pile uplift and compression capacities from the static load testing, pile capacities from dynamic testing (CAPWAP® analyses), soil-pile adhesion values, wave equation factors, soil strength vs. time dependency, foundation design (anticipated pile tip elevation) and pile driving recommendations.

Jan 1, 1995

By Joel Moskowitz

In 1990, the United States General Services Administration (GSA) issued a contract for design and construction of a new federal court building in New York City. Mueser Rutledge Consulting Engineers (MRCE) served as Project Geotechnical Engineers. The project site is in the historic government district at Foley Square. It is surrounded by the New York County Courthouse to the west, an existing federal prison building and federal courthouse across Pearl Street to the south and southwest, an office structure to the north, and a residential tower to the east. The interior of the site was crossed by streets which have now been demapped. As with many urban sites, this site was previously occupied by tenement buildings or industrial structures demolished near the turn of the century. Remains of old building foundations were exposed during construction excavation. In addition, buried fuel oil tanks servicing the adjacent courthouse were removed and the usual assortment of urban utilities had to be relocated for the new building foundations. Ground surface elevations vary from about 4.5 to 6 m above the local Mean High Water Datum Plane.

Jan 1, 1996

By D J. Woodward, A B. Christie, S A. Henrys

Low-level aeromagnetic data available in digital form have been combined to produce a new 1:100 000 scale map of total force anomalies of the Coromandel region, New Zealand. The map incorporates data from 13 surveys flown between 1977 and 1990 and shows the regional magnetic pattern as well as more detailed localised anomalies. In addition to magnetic anomalies, the map also depicts data to aid interpretation, including small-scale maps of topography, geology, magnetic intensity gradient and apparent magnetisation. The primary magnetic anomalies of the Coromandel region are associated with Late Miocene and Pliocene volcanic rocks, but have been locally modified by intense hydrothermal alteration caused by geothermal activity. Epithermal gold-silver and porphyry copper deposits are associated with zones of hydrothermal alteration. The map of magnetic anomalies can be used as an aid to mineral exploration and the interpretation of the processes that control the distribution of mineral deposits in the region.

Jan 1, 2001

By S. H. Badenhorst

Zacharias Lewala discovered a diamond at Grasplatz, near Lüderitz in April 1908. While this stone may not have been the first diamond to be found in this barren, inhospitable area, it most certainly was the stone that set off a chain reaction ultimately leading to the creation of Namdeb as we know it today. [ ]

Jan 1, 2003