Search Documents

The 15m high Inco flash furnace uptake was designed as a reaction chamber with the objective of destroying the H2S contained in the furnace off-gas by combustion with oxygen at about 1300°C. Until recently, the oxygen required for this purpose was injected through afterburners located at the bottom of the uptake. An undesirable side effect of this practice was the formation of build up accretions on the inside walls of the uptake. This buildup had a negative impact on both the furnace on line time and the control of the flash smelting process. In late 200 I, the afterburners were relocated to the roof of the uptake. As a result, about 80% of the uptake accretion buildup disappeared with obvious beneficial effects for the operation of the furnace. This paper discusses key flash smelting aspects that affect the operation of the flash furnace uptake such as the dusting rate, the formation of H2S in the freeboard of the furnace, and the impact of using coke to supply some of the heat required by the process. The mechanism of buildup formation and its dependence 'on uptake afterburners location are also examined. Prof. Yazawa's sulfide smelting thermodynamic relationships proved instrumental in understanding the conditions that influence the formation and the elimination of H2S and uptake buildup.

Jan 1, 2003

By Robert S. Gärtner

The selective aluminum extraction by 3 different calixarenes (p-tert-butyl-calix[4]arene-tetra¬2-acetic-acid-ethyl-ester, p-tert-butyl-calix[4]arene-tetra-2-acetic-acid and p-tert-butyl-calix-[4]arene-di-2-acetic-acid-ethyl-ester) from an industrial pickling bath solution was studied. The pickling bath solution contained hydrofluoric and phosphoric acid as its main components. The aluminum removal was not successful and also no significant extraction of trace metals present was observed.

Jan 1, 1999

By Julie M. Melluish

The metallurgical response of the Point Leamington deposit has been studied. Two series of bench tests were conducted and various ore samples and flotation products were examined using image analysis techniques. The majority of sphalerite and chalcopyrite grains in this texturally complex ore were found to be smaller than 10 micrometres. Copper recoveries were low with losses mainly as fine inclusions in pyrite. Sphalerite recoveries were somewhat better due to a generally coarser habit. Gold and silver recoveries were also low and only solid solution silver was identified in the ore. The deposit shows poor economic prospects unless additional tonnage of high grade zinc ore can be delineated.

Jan 1, 1989

By K. H. Bech, S. T. Johansen

"The mass transfer at fluid-fluid interfaces due to turbulent agitation is investigated theoretically. In particular a theory is derived for interface stresses due to interface energy and surface renewal. This theory indicates that surface renewal may take place if the geometry is sufficiently large and if surface tension is sufficiently low.By using a model for a typical turbulent structure we compute the interface mass transfer for a stressless interface and a fully interface. Results for the general situation is not presently available. The computed results are used to derive analytical expressions for the mass transfer based on turbulent kinetic energy and free stream turbulent length scales.One important application of the theory is the mass transfer at the electrolyte side of the bath-metal interface in the Hall-Heroult process. For this process we show that mass transfer should be expected to be of the rigid surface type."

Jan 1, 1999

By T. T. Natarajan, Nagy EI-Kaddah

"Numerical simulation of electromagnetic confinement systems generally requires large CPU time due to the strong coupling between the electromagnetic and the free boundary problems. The present paper examines the accuracy and the computational efficiency of the most common numerical schemes used in modeling such systems. Levitation melting was taken as a test case. In this study, a comparison was made between the finite element and surface integral methods for electromagnetic field calculations. The computational efficiency of Lagrange and the modified Hestenes methods for solving the free boundary problem were investigated. The convergence of the Lagrange method was found to be much faster than the modified Hestenes method. It was also found that finite element method not only gives accurate solutions, but faster convergence to the final equilibrium shape than the surface integral method. The applications and the limitations of these techniques in modeling electromagnetic confinement systems will be discussed.IntroductionIn recent years there has been a growing interest in the use of electromagnetic forces for confinement of molten metals as a means to eliminate molten metal contamination during melting and to improve surface quality of cast products. Continuous casting of metal without contact of a mold is now a reality, and is being commercially applied for casting of aluminum slabs /1/, and copper rods /2/. New applications of electromagnetic confinement in melting and casting include containerless melting (Magnetic Suspension Melting) /3/, edge containment in twin roll casting, and meniscus shape control in continuous casting of steel /4/.Modeling of confinement systems involves the determination of the electromagnetic field and the equilibrium shape. These two problems are strongly coupled due to the dependence of the field on the shape of the melt. While significant advances have been made in computational electromagnetics /5/, the application of developed computational techniques to electromagnetic confinement problems is not a simple task. The principal difficulty in using these methods is that the solution domain is not known a priori. due to coupling between the electromagnetic field and the free boundary problems. These two problems have to be solved simultaneously, leading to an iterative solution procedure. As a result, numerical simulation of electromagnetic confinement systems are computationally intensive with computational time at least an order of magnitude larger than the fixed domain problems."

Jan 1, 1994

By Mehdi Asgharifar, Rouzbeh Sarrafi, Radovan Kovacevic

"The surface treatment of aluminum alloys using atmospheric-pressure of low intensity DC plasma arc discharge is investigated in terms of surface properties. With respect to the conventional surface treatment processes for aluminum alloys mostly based on chemical etching or sand blasting, this process is very environmentally friendly and cost-effective. The effect of two processing parameters, the current and the plasma torch scanning speed, on the surface morphology is studied by using a scanning electron microscope. The effects of cathode spots within the tested range of process parameters are determined, and the limiting factors of the process (such as surface cracking) are discussed. The topographical studies of the treated surfaces have suggested potential enhancement of surface properties for different applications, such as preparing surface for painting and adhesive bonding.IntroductionIn the last decade the aluminum alloys are finding broad applications in automotive industry. In order to successfully execute the joining process of aluminum alloys such as arc welding, laser welding, and adhesive bonding, there is a need to remove oxides for welding and texture the surface for bonding along the join line. A number of surface treatment techniques such as chemical etching, sand blasting, and plasma treatment have been used by industry. It is shown [1] that plasma surface treatment is characterized as environmentally friendly, lower cost, and easier to control process. Bogaerts et al. [1] mention that when an adequately high potential difference is applied between cathode and anode, electrons are accelerated toward anode by an electric field coming in collision with gas atoms. The gas breaks down into positive ions and electrons, giving rise to gas discharge. The DC electrical discharges used in industrial plasma sources can be related to their location on the voltage-current curve as shown in Figure 1.It is generally believed that dark discharges other than coronas, and arc or torch plasmas are not very good candidates for surface treatment because oflow or high power density and active species flux. However, the glow discharge plasma is used for plasma surface treatment applications because of its proper power density and active-species flux [2]. Our objective is to investigate the feasibility of using low intensity DC plasma arc discharge as a surface treatment method without damaging the cathodic non-thermionic workpiece."

Jan 1, 2011

By Y. H. Su, C. Y. A. Tsao

"The solidification behaviors and velocity of atomized droplets during flight is formulated by a mathematical model, in which the concept of transient nucleation is applied. During the flight, the droplet velocity shows a maximum, followed by an inflection phenomenon. The velocity of large droplet is lower than that of small droplet at shorter flight distance, and higher than that of small droplet at longer flight distance. The effect of the gas flow pattern is more significant at longer flight distance than at shorter flight distance at a given flight distance, large droplet has higher temperature than small droplets prior to nucleation. Large droplet has higher nucleation temperature than small droplet. Medium size droplet flies over the shortest flight distance before the nucleation starts. At the end of recalescence, large droplet has less solid fraction than small droplet has.IntroductionTraditional concept of steady state nucleation was used in all the previous models describing the solidification of molten droplets. [1-5] However, during atomization, the solidification rate of the molten metal droplets is very high, and therefore there is very little time for the nucleation event to occur. In the present work, the concept of transient nucleation [6] is considered to model such short nucleation event during solidification of the atomized droplets. The solidification behaviors and velocity of atomized droplets are modeled and the effects of the atomization gas flow pattern are also presented."

Jan 1, 1997

By Hubert Bril, Priscilla Pareuil, François Bordas, Emmanuel Joussein, Jean-Claude Bollinger

"According to the legislation, valorization type, origin and characteristics of waste material, various standard procedures are available to evaluate environmental impacts. A Mn-rich slag was sampled from a metallurgical plant. After its characterization (elementary analysis and mineralogy), five standard procedures were carried out (i.e. TCLP, EN 12457-1). Each fixed parameter of the standards was systematically studied in a large range: pH, Liquid/Solid ratio, contact time. For example, EN 12457-1 led to a low ME mobilization, increasing with the L/S ratio, the contact time and an acidic pH. As a conclusion, the representativeness of the considered parameters and their potential variations are predominant to assess of the real environmental impact during slag reuse. Introduction Recent studies have been carried out about environmental impacts of waste containing metallic elements (ME) because of their potential mobility [1-7]. Indeed, slags are either dumped or valorized in various activities such as building materials. In order to assess environmental risk, various standard procedures are used depending on country legislation, origin of waste and valorization way. Results of leaching tests are linked either to special legislation (e.g. Dumping: EC, Council Decision 2003/33/EC, Construction products: EC, Council Directive 89/106/EEC) or to legal levels used in drinking water (Directive 98/83/CE) when leachates could migrate to groundwater. If ME in leachates are lower than drinking water authorized levels, the waste will be considered as non-hazardous. On the contrary, if the leachable amounts exceed them, the question about the risk has to be posed. Beyond the abundance of leaching tests available, variety of operational conditions induced by these regulatory tests does not make the choice easier. According to operational conditions induced, ME release could vary from one test to another one. ME concentrations in leachates depend on pH, Liquid/Solid ratio, contact time and particle size [3]. To highlight the importance of these operational parameters, potential risk for valorization of a manganese-rich slag was assessed by comparing several standard leaching protocols [8-12] with a global study dealing with the influence of operational conditions. For each regulatory protocol, the most influential parameters (L/S ratio, pH, particle size and contact time) have been studied in a large range."

Jan 1, 2008

By A. E. Clark

Rare earth compounds are widely known as possessing many extraordinary magnetic properties. In this paper, we focus on the huge magnetically induced displacements (magnetostrictions) which characterize the compounds of terbium with iron (Terfenol). Materials prepared commercially by both free-standing-zone (FSZ) and modified Bridgman (MB) techniques have now become available in large sizes and shapes. Prior to the development of the Terfenol alloys, it was possible to achieve giant magnetostrictions only at cryogenic temperatures. In the cubic Laves phase TbFe2 compound, saturation strains exceed 3000 x 10-6 at room temperature and above. Large magnetization 'jumps' can occur, causing huge spontaneous magnetostrictions with small triggering magnetic fields.

Jan 1, 1992

By Jin Zuomei

The kinetics of dissolution of nickel matte in the presence of manganese dioxide with silver ions was investigated. The catalytic silver ions enchanced the leaching rate up to a factor of 17. The effects of stirring, temperature, particle size, concentrations of Mn02, silver and ferric ions, and the experimental procedures were studied. Solid residues at various levels of nickel extraction were examined by SEM, TEM, electron micoprobe and X-ray diffraction. These results indicated that the dissolution reaction was topochemical and fits a surface reaction control model. The activation energy was calculated to be 39.15 KJ/mol. The leaching rate of Ni3S2 was independent with stirring rate, but the reaction rate constant was inversely proportional to the initial particle diameter. The order of the reaction rate are 0.41, 0.69, 0.33 with respect to Ag+, Mn4+ and Fe'+ con-centration respectively. Thus a kinetic rate equation was developed. Moreover, we propose a mechanism of silver catalyzed leaching of Ni3S2'

Jan 1, 1990

By N. Moelans

A method using an ex-situ electrochemical measurement device was developed to determine the oxygen potential of non-ferrous metallurgical slags. The electrochemical cell consists of the molten slag sample, an inert Ir electrode, a stabilized Zr02 solid electrolyte and a NiINiO reference electrode. Different slags from non-ferrous pyrometallurgical processes were analysed at 1100 and 1200°C and pO2 values between 10-3 and 10.12 bar were obtained. The measurements were evaluated with? thermodynamic calculations and using processing considerations. It was found that the reproducibility and stability of the measurement was significantly improved by shielding the molten slag from the atmosphere by a thin layer of carbon, especially for slags with a low oxygen potential.

Jan 1, 2003

By Jewel Gomes

Green rust is an important intermediate in oxidative transformation of Fe(II) phase. This unstable compound contains a mixture of ferrous and ferric hydroxides that belong to a family of minerals known as layered double hydroxides (LDH). Its general formula is [FeII(6-x) FeIIIx (OH)12]x+[Ax/n-*yH2O] x-, where A is an n-valent anion mainly Cl-, CO3-2 and SO4-2, and in which either the bivalent or the trivalent iron can be replaced for other trivalent or bivalent metal ions. It was first identified as corrosion product, later in soils as a product of interactions between microbes and metals in soils. Due to its high reactivity, it is used in the reduction of organic and inorganic compounds, As removal, and the treatment of acid mine drainage. In this paper, we described the method of electrochemical generation of green rust, its characterization by XRD, SEM and FT-IR, and its implications to electrocoagulation.

Jan 1, 2009

By A. P. Paiva

Studies focused on the recovery of precious metals by solvent extraction have recently increased. either to devise suitable solvents or to clarify the involved extraction mechanisms and kinetics. In this work, a comparison of the performance exhibited by triphenylphosphine (TPP), bis-(penty1thio)-ethane (BPTE) and triisobutylphosphine sulfide CI"I'BPS) in the extraction of silver from acidic chloride media is carried out. Extraction and stripping isotherms involving the three extractants are presented together with the results obtained on the selectivity of silver extraction against high contents of iron, copper and lead. Attempts to clarify the mechanism of silver extraction by TIBPS were performed by studying the distribution coefficient dependence on ligand and chloride concentrations. The effect of temperature on extraction and stripping is also considered. The interfacial tension for the system, measured with different concentrations of extractant in the organic phase, is analysed.

Jan 1, 1994

By Toshiyuki Nohira, Eiichi Takeuchi, Tetsuo Oishi, Hideki Ono, Hirokazu Konishi

The Dy-Nd-Pr-Ni alloy sample was prepared by cathodic potentiostatic electrolysis at 0.65 V (vs. Li+/Li) for 1 h using a Ni plate in a molten LiCl-KCl-DyCl3-NdCl3-PrCl3 system at 723 K. The highest mass ratio (Dy/Nd+Pr) in the alloy sample was observed to be 50 at 0.65 V. Anodic potentiostatic electrolysis at 2.20 V for 12 h was conducted using the Nd-Fe-B magnet electrode in a molten LiCl-KCl system. All elements were almost dissolved from the magnet, and the original form of the magnet disintegrated. After anodic potentiostatic electrolysis at 2.20 V, cathodic potentiostatic electrolysis was conducted at 1.00 V for 5 h using a Mo plate in order to remove the dissolved Fe from the bath. Finally, cathodic potentiostatic electrolysis was conducted at 0.65 V for 12 h using a Ni plate. The mass ratio of Dy/Nd in the alloy sample was determined to be about 18.

Jan 1, 2015

By M. Nishikawa

The Hachinohe Smelter employs the Imperial Smelting Furnace (ISF) for production of zinc and lead and handles a large number of concentrates and recycled materials. In recent years, recycled materials such as zinc-bearing materials, lead sludge and Waelz oxide have provided up to 30% of the feed materials at the plant. To allow for a satisfactory operation using such a wide range of recycled materials, the Hot Briquetting Plant was built in 1986 and started its operation in January 1987. In April 1988 the zinc production capacity of the ISP was increased from 81,000 to 101,000 tonnes per year. The additional production in the ISP has been attributed to the utilization of the hot briquetting process. This paper describes the various facts of the smelter, concentrating on hot briquetting operations and treatment of hot briquettes in the ISF.

Jan 1, 1991

By Serdar Aksu, Fiona M. Doyle

"CMP will be an essential process in the production of integrated circuits containing copper interconnects. This study aims to improve our mechanistic understanding of the role that organic chelating agents might play in the reactive slurries used in copper CMP. Copper dissolution behavior in EDTA arid glycine was first examined by producing potential-pH diagrams for the copper-water-EDTA and copper-water-glycine 'systems. The results of potentiodynamic polarization experiments were then considered in light of these diagrams. . In-situ polarization experiments were conducted to gain insight into the electrochemistry of copper during dynamic polishing in slurries prepared from EDT A and glycine.IntroductionCopper has recently started to replace aluminum as the interconnect metal in integrated circuits. Copper interconnection offers faster and more reliable integrated circuits due to its higher electrical conductivity and superior electromigration resistance (1). The damascene method is used to form multilevel interconnects in the manufacture of integrated circuit devices with copper metallization (2, 3). Copper is deposited by CVD or electroplating into vias and trenches etched in the interlayer dielectric (IDL), over a diffusion barrier usually made from titanium, tantalum or their nitrides. Chemical mechanical planarization (CMP) then prepares the wafer for the next deposition step, by removing excess copper and planarizing the surface. During CMP, the wafer is rotated and pressed against a rotating platen covered with a polishing pad. Chemically active slurries containing submicron size abrasive particles (Si02, Al20 3, ceria, diamond, etc.) are applied. Both the mechanical action of the abrasive particles and the chemical action of slurry constituents remove material from the wafer surface. Planarization results because material is removed faster from protruding regions on the surface than from recessed regions. Since CMP can globally planarize .the entire wafer, it has become one of the key technologies for producing integrated circuits with copper metallization."

Jan 1, 2000

By Henrik Gudbrandsen, Geir Martin Haarberg, Ana Maria Martinez, Karen S. Osen, Sverre Rolseth

"The Several approaches were tried for developing an electrochemical route for producing high purity silicon from molten salts. K2SiF6 and metallurgical grade silicon were used as the source of silicon. Molten LiF-KF and pure KF with additions of K2SiF6 were used as electrolytes at temperatures from 550 - 900 oC. Silicon was cathodically deposited and anodically dissolved in the fluoride electrolytes. High electrorefining efficiency was obtained for many elements after electrolysis experiments at constant potential or constant current. The main challenge was to reduce the contents of boron and phosphorus. Another difficulty was to remove inclusions of solidified electrolyte. The lowest energy consumption was estimated to be ~ 3 kWh/kg Si, while the best current efficiency for Si deposition was found to be ~ 95 %.IntroductionSilicon is the most important material for photovoltaic power generation devices because of high feasible efficiency, low ecological impact and slow degradation. Development of a new and less expensive route for producing silicon of the desired quality is necessary in order to make solar cells competitive. Electrochemical routes may be an alternative possibility, and many laboratory studies have been reported over the past few decades. Most of the studies have been performed in molten salts, chloride or fluoride, at moderate temperatures so that solid silicon was deposited at the cathode. The production of high purity silicon has shown an annual increase of about 25 %, due to the increasing demand of solar grade silicon (SoG-Si). For future increased use of solar energy it is important to develop alternative, more energy efficient and cheaper processes for SoG-Si production compared to the Siemens process.Common silicon sources have been SiO2 and K2SiF6 for electrowinning and MG-Si in the case of electrorefining. A serious challenge is to find an oxygen evolving anode for electrolytes containing dissolved oxides. Especially at moderate to high temperatures and in molten fluoride electrolytes this is a difficult task.Many experimental results have been reported in molten chloride electrolytes. Nohira et al. [1-3] and Chen et al. [4] cathodically deposited silicon by electrodeoxidation of solid SiO2 in molten CaCl2 by potentiostatic electrolysis. An alternatice approach is to use electrorefining of low-cost metallurgical grade silicon (MGSi) to produce SOG-Si. In previous studies [5], an MG-Si anode was used, and silicon was successfully electrodeposited on a molybdenum wire in a CaCl2 based melt. It was found that the anode was strongly passivated due to the precipitation of silicon. Also, some deposits detached from the molybdenum wire because of the poor adherence to the cathode.Considering the Cu-Si alloy which has a good segregation effect for some impurities, and should not passivate, could be a good candidate anode for electrorefining. [6]."

Jan 1, 2014

By H. Kamarudin

The behaviour of cassiterite-sulphosuccinamate flotation system was examined in the light of zeta potentials measured by micro-electrophoresis method. It was observed that sulphosuccinamate substantially affects the zeta potentials of cassiterite, lowering its i.e.p. to pH 2.5 and indicating a specific adsorption and/or chemical interaction. The optimum concentration for flotation, as seen in micro-flotation tests, was found to be associated with the most effective lowering of the zeta potentials, the optimum pH being 3.0. The effect of cations in the pulp was examined for the presence of ferrous, ferric, aluminium and lead ions. The ions ferric and aluminium were observed to create an intense effect of increasing the potentials to positive side, possibly due to adsorption of cation hydroxy complexes, as indicated by their respective species distribution diagrams.

Jan 1, 1994

By Adele Garkida

Compacts of crushed waste window glass, fluorescent tubes, drinking glasses and laboratory glass wares were made at various proportions from 106 microns and minus 75 microns powders in combination with 5% bentonite as binder for each glass type, after several trials to determine compatibility of particle sizes. They were made using the uniaxial press at 10,000 psi and sintered at a temperature range of 700- 750oC. The results showed anisotropic shrinkage behavior for all the samples, exhibiting an axial shrinkage lower than the radial shrinkage. Sintered compact from waste drinking glass which comprised of 60% 106 microns and 40% minus 75 microns powders showed the least sintering shrinkage factor of 1.125, fused at 700oC and the highest shrinkage factor of 1.286 obtained at 750oC. This shrinkage behaviour connotes that sintering can be employed to utilize these waste glasses up to the maximum of 95% recycled glass content in ceramic tile production.

Jan 1, 2008

By Maribel L- Saucedo-Muñoz, Toshiyuki Hashida, Victor M. Lopez-Hirata, Shin-Ichi Komazaki

"Small-punch tests were conducted at 4, 77 and 293 K on three types of austenitic stainless steels JNl, JJl and JK2, which were solution treated, water-quenched and then aged at 923, 973, 1023 and 1073 K for 5 h. Small-punch test energy was employed for the evaluation of the aginginduced embrittlement behavior in these materials. Fracture surface of small punch test specimen for the solution treated steels exhibited a ductile fracture, showing the highest SP test energy values. The presence of intergranular brittle fracture was observed in aged specimens. Smallpunch test energy decreased significantly as the aging process progressed. The highest and lowest decrease in small-punch test energy with aging temperature occurred in JNl and JK2 steels, respectively. The decrease in small-punch test energy showed to examine appropriately the aging-induced embrittlement in these materials. The difference in aging-induced embrittlement behavior for these steels was explained based on the volume fraction of intergranular precipitates in aged samples.IntroductionA high level combination of strength and toughness is required for cryogenic structural materials used in the superconducting magnets of fusion nuclear reactor. This requirement is beyond the capability of conventional austenitic stainless steels [1]. The Japan Atomic Energy Research Institute (JAERI) developed new cryogenic JNl, JJl and JK2 austenitic stainless steels. The structure of superconducting magnets is supposed to be constructed by welding thick plates of this kind of steels. Thus, most of the components are exposed to thermal cycles. The slow cooling may cause microstructure changes in both the base material and weld zone. These changes may also decrease the fracture toughness of these materials at cryogenic temperatures. Therefore, it is important to study the effect of thermal aging on fracture toughness behavior for these steels. Konosu et al. [2] carried out a study of the effect of thermal aging on the mechanical properties for JNl steel using tension and fatigue tests. Kwon et al. [3] evaluated the deterioration in fracture toughness at cryogenic temperatures for the isothermally aged JNl steel by means of the Small-Punch (SP) test. No other reports were found about the cryogenic fracture toughness behavior for this kind of steels. To evaluate the cryogenic fracture behavior, the elastic-plastic Jrc value is a good alternative [4,5]; nevertheless, the standard required specimen size makes it difficult to be used for the fracture toughness evaluation in small zones."

Jan 1, 2011