Search Documents

By S. Tandon

Equilibria studies of selenium distribution for sodium-borate slags were initiated at 1473k under reducing condition as a function of slag composition and alloy composition. The Se distribution coefficient (% Se in slag/% Se in metal) increased from 0.4 to 2.9 with increase in basicity (0.53 to 0.86) for Cu-0.446% Se alloy. However, the results are not very useful from industrial application viewpoint. Therefore, in order to improve the distribution of Se, CaO (10% to 50%) was added to the sodium-borate slag of basicity 0.864. On addition of 502 CaO, the distribution coefficient increased roughly by 100% for slag composition - 44.5% Borax, 22.2% Na2C03, 33.3% CaO and Cu-0.44677 Se alloy. Further, the value of this distribution coefficient has been found to increase by an additional 80% on addition of 20% CaF2 to the above slag for all Cu-Se alloy compositions. Also with increase in initial concentration of Se, the distribution coefficient has been noted to increase.

Jan 1, 1992

By C. Allen

A series of zinc chloride electrowinning tests was carried out in a laboratory scale cell to evaluate the effect of temperature, current density, electrolyte composition, gas sparging and additives on the performance of the cell with respect to current efficiency, voltage, specific energy consumption and deposit morphology. The anode material was DSA for chlorine evolution and the cathode was made of aluminum. At 400 A/m2 current density, a current efficiency of 90.9%, a voltage of 3.4 V and an energy consumption of 2.78 kWh/kg were observed. Air sparging was found beneficial but was not pursued for health and safety reasons. Various additives in the same chemical family as tetrabutyl ammonium chloride (TBAC1) were tested. Both TBAC1 and tetrabutyl ammonium bromide were found to be equally effective. Attempts to carry out the electrolysis at 1200 A/m2 were not as successful.

Jan 1, 2000

By Wenbin Liu

A novel route for rapid synthesis of ultrafine WC-Co cemented carbides with homogeneous binder phase distribution is reported. The composite powder is produced by in situ reduction-carbonization reactions by using WO2.9, Co3O4 and carbon black as raw powders. The reaction equilibrium and phase stability are studied by thermodynamic calculations. The WC-Co composite powder is condensed by spark plasma sintering (SPS) to obtain the cemented carbides bulk. The sintering temperature is lower than that in the conventional sintering methods by 1500C, while the sintering time is remarkably reduced by 3-5 times. The high performances of the hardness and the fracture toughness are obtained. The experimental results confirm that the present processing scheme of in situ reduction-carbonization reactions and subsequent SPS sintering is an efficient way to prepare WC-Co cemented carbides, and is apparently superior to the conventional long-period techniques of preparing composite powder and cemented carbides bulk.

Jan 1, 2008

By Bart Blanpain, Tom Peter Jones, Muxing Guo, Liugang Chen, Huayue Shi

Fayalite based slag is formed during the smelting process of secondary copper resources. It was found that with the presence of high ZnO, the slag became viscous, causing a slag tapping problem. In the present paper, the phase relations of the slag system ZnO-“FeO”-SiO2-Al2O3- CaO (ZnO = 0-12 wt%, Al2O3% = 0-15 wt%, CaO = 0-1.5 wt%, with iron saturation) at 1150 °C is studied by using quenching technique followed by phase identification and compositional analysis of equilibrated samples. The dependence of FeO and Al2O3 solubility in the liquid slag on the chemical composition of slag is characterized. Based on the experimental data, the solid fraction of the slag, which may considerably, influences the slag viscosity, at the tapping temperature can be reasonably estimated and, therefore an appropriate modification of the slag composition can be made.

Jan 1, 2016

By Ki Bui Ma

Momentum wheels with superconducting bearings can integrate both attitude control and energy storage functions, with attendant savings in the total volume and weight of hardware, and power consumption, all of which are in short supply on mini-satellites. We have built and tested a prototype with a wheel of mass 1.9 kg, diameter 3.25 in, and height 3 in, which can store 3.5 J-sec of angular momentum and 5 kJ of energy when it rotates at an angular speed of 15000 RPM. The energy density of 2.5 kJ/kg achieved is comparable with the lower range for lead-acid batteries. To show that the wheel is energy efficient, we have performed spin down tests and measured the input power required to sustain rotational speed. Results indicate that power consumption, even accounting for the needs of cooling system, is significantly smaller than that for state of the art commercial reaction wheels.

Jan 1, 2002

By Alexandra Anderson

A computational fluid dynamic (CFD) model has been developed using ANSYS Fluent 17.0 to help identify areas of high wear within the refractory lining of a secondary lead reverberatory furnace. Once a base case simulation was validated using data from an operational furnace, areas of potentially high refractory wear were determined through the calculation of the temperature and velocity distributions within the furnace and on the hot face of the refractory lining. The CFD model was used to assess whether the predicted areas of high refractory wear could be minimized through changes burden geometry. The results showed that shape of the burden geometry greatly affected the overall flow patterns and heat transfer within the furnace.

By Aureo D. V. Machado

An experimental study to obtain zirconia powders (ZrOz) from carboxylate zirconium solutions followed by hydrogen peroxide stripping and precipitation, has been carried out. Zirconium carboxylate was prepared by solvent extraction from a chloride aqueous phase using magnesium carboxylate as organic phase. The variables examined in the precipitation reaction were: Temperature: 25 - 90 ?C ? H202= concentration: 0.3 - 5% wt/wt - pH: 1 ? 9 Organic/Aqueous ratio (1/1) and reaction time (30 minutes) were maintained at constant levels. The optimum results (98% precipitation) were achieved at 25 °C, 5 % wt/wt H202=, and pH = 5. The precipitates were composed of large amorphous aggregates (<I00 micrometers). After calcination for 1 hour at 1000 OC, monoclinic ZrO2 with a large variation in particle size (1 -100 micrometers) was obtained.

Jan 1, 1991

By Lidong Teng, Seshadri Seetharaman, Aida Abbasalizadeh

0In the present paper, the feasibility of the recovery of dysprosium from spent Nd-Fe- B magnets containing approximately 9 wt% Dy was investigated by using molten salt process. The salt bath consisted of a mixture of NaCl-KCl-LiCl corresponding to the ternary eutectic composition. AlCl3 was used as a chlorinating agent in order to enable an efficient dissolution of metal in the molten salt phase in the salt bath. The metal chloride which is formed as the result of chemical reaction between the metal in magnet and AlCl3, is subsequently subjected to electrolysis in order to be deposited on the cathode. Graphite rods were dipped in the salt bath as electrodes and alumina crucibles were used as the containers for the electrolytic cells.

Jan 1, 2014

By Luis G. S. Sobral, Gabrielle N. Bard

Copper sulphides Concentrates, from the flotation process of copper primary ore; contain, commonly, small amounts of precious metals, such as gold and silver. During the smelting process of those concentrate all gold and silver are practically in the blister copper, which is cast into anodes. Those copper anodes are electrorefined in an electrolytic system, where the electrolyte is an acid copper sulphate solution, where a high purity electrolytic copper is produced (>999,9/1000). The slime when submitted to an oxidative leaching process, using sodium hypochlorite and hydrogen peroxide as oxidizing agents, turn those metals into solution. This research practical work, apart from concentrating effort on the digestion of the anode slime, aims at evaluating the efficiency of the cementation process of the metals of interest for the separation of them to take place. 141

Jan 1, 2008

By Ken-ichiro Uemura

"The DIOS process has been developed for eight years since 1988. The research project was started with the element studies carried out by each of the five integrated steel making companies in Japan, the final two and half years were spent for the pilot plant studies. Operation were conducted in the entirely closed and pressurized system successfully as planned. From the result, the DIOS process was proved to be viable as a future iron-making process substitutable for the conventional blast furnace. In addition, a lot of findings were obtained. Hot metal productivity was primarily determined by a oxygen flow rate, and a coal consumption varied depending on the productivity. The post combustion ratio was a little lower than expected from the result of the element study. It was supposed to relate the gas-reforming with coal or volatile matter in the free space of the furnace. Hot metal carbon content seemed to depend on the char content in slag.INTRODUCTIONThe JISF's DIOS pilot plant (DIOS=Direct Iron Ore Smelting Reduction Process) has finished its last campaign of the operations in January 1996. The project was started in 1988 as a joint research of the Center for Coal Utilization, Japan and the Japan Iron and Steel Federation (JISF) with a subsidy for promoting coal productions and utilization technologies from the Agency of National Resources and Energy, the Ministry of International Trade and Industry(MITI). Throughout the pilot plant test, a total of over 20,000 tons of hot metal was produced for more than 2,000 hours of the operation. Recorded production rate was 538 ton/day for 3 days at a specific coal consumption of approx. 1,000kg/hmt. Long-term operation was carried out in the fifth campaign for 18 days, which has proved that the entirely closed and pressurized DIOS process works well as planned. In Figure 1 is shown the representative operational performance obtained in the first five campaigns. The project is going to be finished by the end of March this year after investigating the technical viability and economic potential of the process, and completing the conceptual design of the DIOS commercial plant. In this paper, the system and facilities of the DIOS process are first introduced and some of the results of the pilot plant test are detailed later."

Jan 1, 1996

By Peter Sylvén, Darwin Morales

Despite being crucial for the smelting process, furnace tapping using oxygen lances has not been considered an operation that brings value. Therefore, these important tools have not seen a significant change in over 100 years. Problems related to the use of oxygen lances include: • Inaccurate tool: causing damages shortening the life of the taphole refractories. • Safety: extended exposure to the operator in an unsafe area of the furnace. • Cost: high oxygen consumption & high lance consumption. • Time consuming and frustrating to connect one lance to another. This paper will suggest a very good solution; new concept thermal lances. We will show how these provide an outstanding performance for a more efficient, faster and cost-effective furnace tapping operation. These new lances are very accurate tools that enable the operator to perform a more controlled operation; resulting in longer taphole life, fewer repairs and less down-time.

Jan 1, 2016

By Yuanbo Zhang, Xiaoming Mao, Zhixiong You, Zhenyu Fan, Tao Jiang

"It is generally known that the formation of calcium ferrite is favorable during the iron ore sintering, which dominatingly contributes to the improvement of strength and reducibility of the finished sinters. In this study, effects of roasting temperature and 02 content of inlet gas on the sintering mineralization properties of typical iron ores, including hematite, limonite, specularite and magnetite, were investigated. The results showed the amount of calcium ferrite initially increased then decreased with the increase of the roasting temperature. The temperature of maximum calcium ferrite generation amount for different iron ores was determined as follows: hematite and limonite was 1275 °C, whereas specularite and magnetite was 1250 °C. Increasing 02 content of inlet gas was advantageous to the generation of calcium ferrite during the sintering. The sequence of 02 content affecting the mineralization properties of different iron ores was determined as follows: magnetite > hematite > specularite > limonite.IntroductionThe mineralization property of iron ore plays a significant role in the mineral composition and microstructure of finished sinters, which determine the quality and output of the sinters [1-2]. The mineralization process of sinters is composed of solid-phase reaction, formation of liquid-phase and crystallization. The formation and crystallization of liquid-phase is the foundation to the mineralization as the quality of the sinter is poor when concreted by solid-phase consolidation [3-4]. With respect to the iron ore sintering, liquid-phase regarded as bonding phase is generated between the iron ores and fluxes at high temperature [5]. Calcium ferrite is the most favorable liquid-phase among the bonding phases which dominatingly contributes to the improvement of strength and reducibility of the finished sinters [6-8]. Especially for high iron-low silicon sintering and high basicity sintering, making sure sufficient calcium ferrite quantity and reasonable distribution is crucial to the sinters [9-10]. Therefore, carrying out the researches on the high temperature reaction properties of iron ores is of great significance [11]."

Jan 1, 2013

By B. C. Jena

In a chromite smelting process for the production of high-carbon ferrochromium, the slag composition profoundly affects operating conditions and the economic performance of the process. For a Canadian chromite concentrate, optimum slag composition and operating temperature were determined by process simulation with a computer model, which is based on parameters, such as the minimisation of slag volume, liquidus temperature, electrical energy consumption and chromium losses. Chromium recoveries are identified for slag compositions spanning wide concentration ranges within the quaternary system MgO-AI2O3- SiO2-CaO. The simulated data are compared with the experimental results.

Jan 1, 1994

By Pandey H. D.

The paper describes a fluidised bed ion exchange method for simultaneous removal of phenols and cyanide from the effluent. Use of an eluant enables regeneration of the resin in the continuous operation mode. The breakthrough experiments conducted both on the laboratory scale and on a pilot plant scale have shown that while the level of phenol can be brought down from 462 ppm to about 6 ppm, the free cyanide is almost totally removed. An examination of data indicates that the method can serve the twin objectives of pollution control and phenolic compounds recovery.

Jan 1, 1992

By C. B. Piazzarollo

Red Ceramic materials are widely used in Civil Construction in Tropical Countries. However, these materials have high porosity and low mechanical strength. Thus, in order to improve these properties, recycle mineral wastes was incorporated into clay from Campos - RJ, ornamental rock waste, from the gneisses cutting of Cachoeiro - ES, 150 km from Campos. After the addition of up 10% of waste in clay mass, ceramic pieces were produced and subjected to the tests of porosity (P) and flexural strength (FS). The test material contains 53.3% clay and 67% waste slit. The X-ray diffraction identified the presence of kaolinite, quartz and feldspar for the clay and, for the waste, quartz and orthoclase. The results of FS and P showed that the residue influenced, positively, the ceramic piece, with strength gains especially from 920º up to 960°C.

Jan 1, 2015

By Muhlis Nezihi Saridede, Burak Birol

"The scraps of high quality steels generally contain expensive alloying elements such as chromium, vanadium, nickel, etc. These scraps are melted in an induction or an electric arc furnace and refined in ESR (Electroslag Remelting) purification process. A significant amount of alloying elements are lost during these processes. In order to avoid these losses, scraps can be utilized directly in ESR by skipping the melting step. In this study, 316L stainless steel scraps were refined in ESR with selected synthetic slags. The products were analyzed by optic emission spectrometry and the effects of slag compositions on the alloying element losses were examined. According to the analysis of the scrap and the products, generally chromium, nickel and manganese losses were encountered. It was determined that the alloying element losses has no connection with electrical conductivity. The slag containing CaF2, Al2O3, and FeO gives the optimum Cr and Ni losses.IntroductionElectroslag remelting (ESR), which is the consumable electrode refining process, finds a wide range of utilization for the production of high quality, low inclusion alloys. This process is based on melting a consumable electrode under a molten synthetic slag containing CaF2, Al2O3, CaO etc. The synthetic slag provides the chemical refining and insulation of molten metal from air which leads to a higher purity and an inclusion-free product. [ 1,2] A schematic diagram of ESR system is shown in Figure 1."

Jan 1, 2011

By Hadi Fanisalek

"Most industries attempted to conduct their energy consumptions in an optimized way for a few decades. This is because policymakers and top managements in industries have felt the critical situation of a possible energy shortage that could happen for them in the near future, even in countries with significant fossil fuel resources. Decisions related to energy consumption in any industry will have a long-term effect on different parts of the industry structure. In this way, energy decisions should be categorized as part of any industry's main strategic and long-term decisions, which should be made by top strategists. On the other hand, strategic management has many powerful tools to help the policymakers in industries to establish a long-term strategy for energy consumption and reducing or preferably eliminating the energy loss. This will be more important for industries in the Middle East, where they have just started to make an applicable strategy for their energy consumption and to design a long-term procedure for their energy management. Based on strategic management and by comparison we designed and offered a new model for establishing the main structure of energy management strategy in primary aluminum industry, which is a high consuming energy industry. This strategy, which we will call ESM (Energy Strategic Model) and has been applied for a typical primary aluminum industry in this paper, is similar to the practical models in the field of strategic management, which were developed for designing the overall company strategy.IntroductionThe elementary goal for introducing strategic management in any organization was to establish a successful plan helping the company to survive and to gain competitive advantage over its competitors in a rough business environment. Strategic management is an ongoing process that evaluates and controls the business and industries in which the company is involved; assesses its competitors and sets goals and strategies to meet all existing and potential competitors; and then reassesses each strategy annually to determine how it has been implemented and whether it has succeeded or needs replacement by a new strategy to meet changed circumstances, new technology, new competitors, and a new economic environment[!]."

Jan 1, 2013

By W. E. Wallace, J. A. Warren, D. Josell, D. Wheeler

"We present the results of experiments and modeling of flip-chip geometry solder joint shapes under shear loading. Modeling, using Surface Evolver, included development of techniques that use an applied vector force (normal and shear loading) as input to determine a vector displacement of the pads connected by the solder joint (standoff height and misalignment). Previous solutions solved the converse problem: fixed displacements used to determine required applied force. Such solutions were inconvenient for applications, where the applied force (chip weight) is known. Also, for geometric and materials studies of solder joint shapes involving multiple parameters, determining the equilibrium displacement from applied force by bracketing solutions could become computationally expensive. Measurements of solder joint standoff height and misalignment as functions of the applied force (normal and shear), solder volume and pad diameter are presented. Experiments were carried out for solder ball diameters from 0.38 mm (0.029 mm3 volume) to 0.15 mm (0.0019 mm3 volume) on pads of diameter 0.64 mm and 0.35 mm. Fitting of simulation to experimental results gave optimized values for the contact angle and surface tension of the solder which were consistent with measured and literature values. IntroductionIn packaging technology flip-chip has become an important method for attaching semiconductor devices to substrates. Generally, the chip and substrate are bumped with solder and then the chip is flipped onto the substrate and the solder reflowed to form conductive interconnects. An epoxy underfill is normally flowed between the substrate and chip to reduce the thermal fatigue on the solder joints. A flip-chip assembly is illustrated in Figure 1.In flip-chip applications, the use of an integrated underfill/solder bump system [1, 2) removes an extra process step, namely infiltration of the underfill. However, the presence of an underfill will retard the self-alignment of the flip-chip. A first step in understanding and predicting this retardation is to develop a model to describe normal and lateral force-displacements curves when underfill material is not present. At this stage it is unclear whether static surface tension theory is sufficient to describe a complete model for flip-chip realignment even without underfill."

Jan 1, 2001

By Carla Lupi, Mauro Pasquali

"Photographic technology is based on light sensitivity of silver halides that, because of silver properties, are capable of forming photographic images. Photographic laboratories and hospital departments because of digital photographic systems less use this technology today. Nevertheless recovery of silver is still advantageous because environmental problems related to Ag ions danger to biological system. Many processes have been studied to treat silver containing photographic bath: cementation, chemical precipitation and electrowinning. In this work, after preliminary voltammetric tests, a batch electrometallurgical process has been studied to completely deplete the silver containing photographic fixing baths. The effect, of silver concentration in the electrolyte, varying over the range 0,2-1 g/L, bath stirring and current density ranging from 10 to 500 A/m2 on process yield and deposit quality, has been investigated. Introduction Photographic wastes, electronic scrap and spent catalysts constitute the main sources of materials for silver recycling. Among those silver secondary sources, the photographic discharged material could be still important and useful, even if photographic laboratories and hospital departments, because of digital photographic systems, less use photographic technology. Several processes have been developped in order to recover silver used in the field of photography from both photographic solutions and scrap film paper[1-5]. Fixing solutions are very complex baths but, because of silver position in the electromotive series, electrolysis could represent an advantageous method for silver recovery. Electrolysis produces high purity silver without generating new pollutants, while the fixer can be reused: obviously it is necessary to purge off a portion of this solution in order to avoid the excessive build up of other deleterious compounds into solution. A tested recovery method was constituted by the dissolution of silver from X-ray films with concentrated nitric acid. Internal electrolysis and external electrolysis methods were carried out using a steel electrode as cathode and a copper electrode as anode [6]. Silver recovery from photographic chemical solutions has been also performed in a special cell [7]: the solution is supplied to the bottom of a non-agitated cell having a vertically elongated form and including a central anode enclosed by a cathode. An other study discloses the use of an electrolytic cell comprising at least one anodic compartment and one cathodic compartment: the solution is treated in the cathodic compartment and then recycled in the anodic one [8]. A more recent work proposes the use of zirconium cathode for the recovery of silver from photographic fixing solution [9]: studies carried out by cyclic voltammetry showed that about 98% of total Ag can be recovered with an electrical efficiency close to 92%."

Jan 1, 2008

By Xia Hong-ying, Peng Jin-hui, Zheng Zhao-qiang, Zhang Li-bo

"Preparation of activated carbon from the walnut shell by microwave assisted steam activation was studied. Influences of the three parameters, activation temperature, activation duration and steam flow rate on the adsorption capacity and yield of walnut shell activated carbon(WSAC) were investigated,optimization process was obtained by the Response Surface Methodology (RSM). The optimum preparation conditions were as follows: activation temperature of 980°C, activation duration of 41 min and steam flow rate of 1.66 ml/min. The optimum conditions resulted in an activation carbon with an iodine number of 1025 mg/g and a yield of 52.17%, while the BET surface area, total pore volume and average pore diameter of WSAC were 1328m2/g, 0.72ml/g and 2.2nm respectively. The study supported the potentiality of comprehensive utilization ofWalnut shell and the benefits of the microwave heating.IntroductionActivated carbons are one of the most important adsorbent materials in modern society because of its abundantly developed pore structure, strong adsorption ability, high surface area and thermo stability. They have extensive application in many industries fields which include gas purification [1], catalyst supports [2] and other pollutants [3]. However, in recent years, the industrial production of activated carbon is facing the problem of raw material scarcity and high cost, which limit to be widely used. Therefore, the selection of an appropriate precursor plays an important role and it has become hot sport to seek cheap raw material to lower preparation cost. As a kind of reproducible resource, the waste from agriculture and forestry is a high-grade raw material for preparing activated carbon due to is high carbon content, such as palm shell [4], rice hull [5], and coconut shell [6]. At present Walnut shell is widely accepted to be a renewable source of biomass. According to statistics, there is more than 1000,000 tonnes of walnut shells are produced in China annually [7]. As a good precursor for activated carbon production, Walnut shell is a major agricultural waste, to make better use of the cheap and abundant agricultural waste, it is proposed for activated carbon production."

Jan 1, 2014