Search Documents

By M. L. Free

Acid consumption in copper heap leaching is determined by the minerals present in the ore. Gangue minerals such as biotite and chlorite consume acid together with copper-bearing minerals such as chrysocolla and malachite. Acid consumption is affected by the rate of acid application and the particle size. Some gangue minerals undergo alterations and cause precipitate formation during acid leaching. Other minerals form due to precipitation as dissolved ion concentrations from a variety of mineral sources combine to exceed saturation levels. Copper recovery is related to all of these events. This study presents information on acid consumption of various gangue minerals as well as data for copper recovery from an associated copper ore.

Jan 1, 2010

By G. V. Sullivan, B. E. Davis, T. O. Liewellyn

A technique was devised by the US Bureau of Mines to recover coarse [+1.2-mm (14- mesh)] North Carolina phosphate now discarded as waste. Concentration utilizes the difference in particle sphericity between the relatively flat calcite and the rounded phosphate pebbles. Sizing, treatment in a continuous hydraulic classification system, and grinding upgraded a 17% P,O5 reject to 4.5% P,05 with a phosphate recovery of 63%. The CaO: P2O5 ratio was reduced from 2.49 to 1.66.

Jan 1, 1987

By J. B. Gwiazda

In designing mine workings and adequate roof supports, it is indispensable to determine properties of the strata surrounding the workings. The proper selection of roof supports is based, before everything else, on a thorough knowledge of the roof rock strength, especially tensile strength. This parameter is a vital factor in the delamination of roof rocks and eventual cave-in. It is also important to know the properties of the floor on which the roof supports are set. While driving galleries, it is essential to know beforehand the strength of rocks that will be encountered in the near future during the work. The devices described will help to obtain this information.

Jan 1, 1987

By St. E. Deák

Mining activities involve excavation from underground to the surface of large quantities of ore (e.g. uranium and its disintegration products) (Dumitrescu, 2002, 2007). Material with limited content of uranium, deemed as sterile or low-radioactive is mainly stored on the surface. These wastes modify the configuration of the disposal areas and affect the quality of the environment and the landscape. This paper presents both analytical and numerical models related to stability assessment of uranium mining waste dumps. It is focused on the calibration procedure of the numerical models, in order to minimize risk error during stability prediction and avoid long term environment pollution.

Jan 1, 2008

By Alfred W. Hefferan

A longwall face conveyor system serves the primary function as all material handling systems; i.e., to transport material between the source and its destination. However, the conveyor system must provide many other functions as opposed to the traditional belt conveyor system. In this paper, we will attempt to contrast the longwall face conveyor system with a belt conveyor system. In addition, the unique problems encountered along with the solutions to these problems will be covered. Table 1 lists the characteristics required of each conveyor system. The table demonstrates the contrast in the two systems. Both must be designed specifically to encounter its unique problems. The balance of this paper will explain how the longwall face conveyor is designed to address its requirements.

Jan 1, 2000

By A. Maréchal

It has been shown since a few years that the problem of estimating recoverable reserves should be solved by using specialized statistical techniques : whenever the selected blocks are chosen without any other constraint than a cut-off grade criterion, the problem of estimating the corresponding tonnage-grade curve is resolved by estimating the local histogram of block grades. Two major statistical techniques are currently used by geostatisticians to estimate local histograms : the "average conditional distribution" technique (Parker, Journel, Dixon 1979) and the disjunctive kriging technique. (Matheron, 1976, Jackson, Maréchal, 1979). Both have proved to be applicable in practice, with their pros and conconcerning their practibility and versatility.

Jan 1, 1982

By R. Ramesh

Understanding the nature of coal surface heterogeneity is a prerequisite to accurate characterization and efficient control of coal surfaces. New techniques based on the centrifugal immersion of particles from the liquid/ vapor interface and film flotation have led to independent estimation of surface energy distributions in individual coal particles. Changes in the distribution of surface sites due to oxidation and polyacrylamide adsorption on coal are studied here using the above techniques. New information on -possible conformations of adsorbed polymers is also obtained.

Jan 1, 1989

By A. English, Edward Martinez, L. A. Haas, N. W. Johnson, Harrison Copper, M. E. Tawil, C. C. Harris, G. V. Jergensen, D. Halbe, M. P. Amsden

Declining US ore grades along with skyrocketing energy, materials, labor, and regulatory costs underscored the urgency for technological innovation in the mineral processing area. Re¬liance on the scale-up and automation of unit operations was the sector's primary battle plan. Debate continues on the upper size limit of concentrating plants and whether process controls should be centralized or distributed in the mill. In the materials handling area, the economics of large-scale and mobile systems, particularly conveyors, were well documented in the literature. Comminution, the most costly and energy consuming area of the processing flowsheet, saw improvements in process controls and liner designs. The trend toward larger grinding units stalled somewhat during the year owing to some operational problems at commercial plants. Research and development of apparently less expensive physical separation processes-that also boast recovery of cleaner and more environmentally acceptable products -gained momentum during the year. Because of escalating capital cost requirements for new plant capacity, the year saw a greater interest by mill designers to re-examine existing capacity. The focus here is clearly to modify or retrofit unit operations with more efficient components as an alternative to installing more costly new equipment. The problems facing the processing sector during the 1970s can be expected to continue in the decade ahead. Technological gains from scale-up and process controls appear

Jan 5, 1980

By T. Knuutinen, M. Klemetti, P. Mörsky

This paper presents a comparison study done at VTT's new pilot plant facilities in Outokumpu, Finland, for chromite ore. The ore was ground in a rod mill -, a ball mill - and high pressure roller mill - ball mill circuit in the capacity range of 0.5 - 3.0 t / h. The main grinding characteristics are discussed and the quality of the products are compared from the mineralogical point of view. The benefits of high pressure roller mill comminution for further mineral processing of chromite is also discussed.

Jan 1, 1995

By Keivan PakIman, Maziar Pasdarpour

Transportation tunnels are highly sensitive to ground movements and are required to be stable and secure for safe operation. In urban areas, the interaction between tunnels and adjacent piles, which are widely used to support buildings and other structures, requires careful consideration. The seismic response of tunnels may vary depending on the lateral stiffness and strength of the tunnel walls, while the axial loading and seismic impact of adjacent piles may cause soil displacement and stress changes that can damage the tunnel lining. As a result, tunnel owners often impose strict limits on the design of new piles lying close to existing tunnels including maximum allowable tunnel deformation, stress change limits, and minimum tunnel to pile separation distances. This paper describes a numerical analysis of the inuence of the axial loading and seismic impact of bored pile foundations on subway tunnels, undertaen using the nite element software laxis D. ased on the results of the numerical analysis, the paper suggests a more realistic and less conservative approach for designing piles in close proximity to transportation tunnels. INTRODUCTION The interaction between tunnels and adjacent piles can cause stress changes and displacements in the soil and structures which may adversely impact structural performance and tunnel safety. It is therefore important to take account of relative load transfer and piling conguration when designing new piles in

Jun 23, 2024

By R. Martinez

The Alligator Ridge Mine was discovered in 1976 by a prospector grubstaked by Amselco Exploration Inc. in eastern Nevada 116 km (72 mi.) northwest of Ely in White Pine County. The mine is operated as a 50-50 Joint Venture by BP Gold, the operator, which is a subsidiary of British Petroleum Minerals America and Nerco Inc., a subsidiary of Pacific Power and Light.

Jan 1, 1988

By Andreas Eberhorn

The evaluation criteria for cost comparison of the Gearless Drive, also called Ringmotor or wrap-around motor, as variable-speed drive with a Twin Drive System using synchronous motors are reviewed. Both mechanical and electrical components of the drive system are considered. The evaluation criteria are described and for the cost comparison the applicable method is demonstrated. The cost comparison is based on a medium and large sized mill system. Each drive package will display cost details with regard to capital cost, maintenance, power losses, overall efficiency, overhead and loss of production. As conclusion the benefits and disadvantages of the two drive/mill packages will be presented together with a payback diagram.

Jan 1, 1996

By C. G. Cunningham

The Marysvale volcanic field of west-central Utah contains large areas of argillically altered rocks (fig. 1) that, in turn, enclose smaller areas of fine-grained, medium-grade, replacement alunite deposits and coarsely crystalline, high-grade vein-type alunite deposits. The largest replacement alunite deposits are [ ] located peripheral to a 23-m.y.-old monzonite stock called the Central Intrusive (fig. 1). The deposits formed in near-surface, highly oxidizing environments at the tops of hydrothermal plumes that were spaced irregularly around the stock. The deposits are horizontally zoned from alunitic cores through kaolinitic to propylitic envelopes. Vertically, characteristic alteration minerals progress from a pyrite-propylitic alteration assemblage at the base, upward through alunitic, jarositic, and hematitic assemblages to a flooded silica cap as shown on figure 2. The silica caps are cut by hydrothermal explosion breccias. d34Sso4 values of + 11.5 to + 15.4 permil indicate that sulfur in the hydrothermal plume was derived from underlying Mesozoic evaporites. The sharp upward transition from pyrite- propylite to alunite probably marks the paleowater table, and the top of the flooded silica cap represents the paleoground surface. Basin-Range extensional tectonism began shortly after alteration, and buried the replacement alunite deposits in basins beneath sediments eroded from uplands. The deposits were only recently exhumed.

Jan 1, 2013

By Debra C. Man, S. Thomas Freeman, F. Wiley Horne

INTRODUCTION The Metropolitan Water District of Southern California (Metropolitan) is the largest water wholesaler in southern California. Its service area spans the major urbanized portions of Ventura, Los Angeles, Orange, San Bernardino, Riverside and San Diego counties. More than 15 million people are serviced by Metropolitan through its 27 member agencies. The primary sources of Metropolitan's water supply are the Colorado River Aqueduct (CRA) and California's State Water Project (SWP). Currently, planning and design level studies are underway by Metropolitan to expand the water storage and conveyance systems within the service area for the purposes of providing increased efficiency and flexibility to manage limited water supplies, improving water quality, and increasing system reliability. The system reliability issue is particularly significant because the conveyance facilities from both the CRA and the SWP must cross the active San Andreas fault. This fault is considered to be the source fault for the anticipated "Big Earthquake" in southern California. To meet these objectives, Metropolitan's expansion plans involve a major new storage reservoir, new large diameter pipeline and tunnel conveyance facilities, more efficient utilization of existing groundwater basins, and an aggressive public awareness and conservation program. This paper focuses on the planning studies that have been carried out for over 50 miles of tunnels being considered for several of Metropolitan's proposed conveyance systems. These tunnels have ranged in length from a few hundred feet to over 42,000 feet, with depths of cover ranging from a few tens of feet to over 3,000 feet, and finished diameters ranging from 10 to 20 feet.

Jan 1, 1993

By Peter Krag, Rob Henson

It is well known that titanium and zirconium alloys offer superior corrosion resistance in the oxidizing sulfuric acid environments present in sulfide pressure leaching operations. The use of these materials is limited, however, due to their pyrophoricity; several accidents attributed to titanium equipment have been described in technical literature, and other, minor incidents·occur regularly1 • We describe an application of a commercial titanium alloy, Nb-55 Ti, with suitable mechanical properties, corrosion resistance similar to Grade 2 Ti, and featuring a significantly reduced field of ignition conditions

Jan 1, 1992

By J. Eldridge, A. J. Carter, D. N. Leavell

Minpro International has developed an innovative, flexible¬shaft impact crusher that produces glass aggregate from mixed¬color, post-consumer glass. The crusher operates with low power and generates a subangular aggregate, with minimal fines. Output is screened to yield sized aggregate, which can be used directly as surfacing material in Owens Corning's shingle process. Metal, plastic and paper waste is preferentially removed by the Minpro system. Duval County and the City of Jacksonville collect more than 12,000 tons of glass bottle waste per year. It is anticipated that a successful end-use application by Owens Corning, will allow increased collection and cost-effective glass recycling in north Florida.

Jan 1, 2002

By P. T. Luckie

More efficient classification with a single hydrocyclone through equipment and/or operating design changes does not appear possible. However, improvement in classification efficiency by increasing the sharpness index and decreasing the apparent by-passing while changing the cut size is possible through proper staging of inefficient hydrocyclones. But feasible multistaging requires achieving the necessary material balances around the units. Because of the interactions among the units, these balances require extensive iterations. The final step before commerical installation should be a laboratory demonstration, in order to define the control algorithm required to maintain stability. However, eventually a sufficient knowledge base should be developed that will permit simulation in place of laboratory testing as well as the incorporation of a feed forward strategy.

Jan 1, 1989

By George McArthur

GEOLOGY One of the largest copper resources in North America occurs in the Bingham mining district, located 40 km (25 miles) southwest of Salt Lake City, UT. Anaconda's present contribution to the development of this resource is the Carr Fork mine. (Fig. 1, Bingham district plan map.) The Carr Fork story began about 300 million years ago when a thick sequence of sedimentary quartzite and limestone was deposited in the Oquirrh Basin. Subsequent earth stresses formed a series of west-northwest-trending overturned anticlines and synclines that were later offset by northwest-striking thrust faults and northeast-trending normal faults. (Fig. 2, Bingham district cross section.) About 38 million years ago the Bingham stock was intruded into some of the folds, resulting in the formation of porphyry ore in the intrusive, and fissure, replacement, and skarn ore deposits in the sediments. The Carr Fork skarns were formed preferentially in two limestone units, called the Yampa and Highland Boy, which average about 46 m (150 ft) in thickness, separated by about 76 m (250 ft) of quartzite. Copper mineralization consists almost entirely of chalcopyrite associated with pyrite and molybdenite in a gangue of garnet, diopside, magnetite, quartz, and carbonate. Molybdenum, gold, and silver are economic byproducts. (Figs. 3 and 4, indicated ore in plan and section.) EXPLORATION HISTORY The West Mountain mining district, of which Carr Fork is a part, was organized in 1863, after leaf-silver ore was discovered in the Carr Fork of Bingham Canyon. However, it was not until 1873, when the Bingham and Camp Floyd railroad to the town of Bingham was completed, that the mining camp flourished. Many small mining companies in the district were reduced, often through consolidation. By 1937 only the National Tunnel and Mines Co. was active in the Carr Fork area. In 1948 it declared bankruptcy, and was later purchased by The Anaconda Co. Anaconda conducted geologic investigations in the Bingham district until 1968, when a concerted diamond drilling program was initiated to fully evaluate the geologic potential of the Carr Fork area. The exploration program commenced with one diamond drill, but was enlarged to three drills following discovery of the first major ore intercept. Near completion of the exploration effort, large oil well rotary drills were used to drill to depths of 762 to 914 m (2500 to 3000 ft), after which the holes were completed by standard diamond drilling techniques. All holes were collared vertically, but considerable deviation occurred because of structure and rock conditions. Wedging and directional drilling were used to keep the holes on target and to provide multiple ore intercepts in the deeper holes. Geophysical surveys, in-

Jan 1, 1982

By John P. Capp

In recent years limited markets have been developed for fly ash, the dust removed from coal-burning powerplant stacks, but most of it is still dumped in spoils areas at a cost ranging from 20 cents to $1.75 per ton. Aside from this cost, the creation of huge spoils areas can present a considerable aesthetic problem. Since the present annual fly ash output of about 20 million tons will probably reach 30 million by 1970, and because satisfactory disposal areas are becoming more limited, markets for much larger quantities of the waste are needed to keep disposal costs from becoming a significant economic factor in coal-burning powerplant operation. Current stress on air-pollution control and beautification, plus the vital need for good powerplant economy, makes it imperative, therefore, that coal producers and consumers expand markets and develop new applications for fly ash. Markets for established uses can be increased by making a greater effort to sell fly ash. New large tonnage markets for fly ash should be sought via more intensive, coordinated research. The economics of fly ash utilization underscores the vital role that must be played by research. To be competitive with other products, processes for the conversion of fly ash into marketable materials face difficulty in regard to two important economic factors--transportation cost and product utility--the other economic factors are favorable. Raw material costs of fly ash, for example, are quite attractive, and supply is no problem because there are many coal-burning powerplants in operation and many more are planned. Demand for products made from fly ash will grow if their utility is established and a good sales program is initiated. The major problems then are transporta¬tion costs and development of useful products.

Jan 1, 1966

By Harland E. Cofer

A computer-assisted resources and sedimentological study of the Andersonville, Georgia kaolin-bauxite district was begun in 1975 under a grant from the Office of Mineral Resources of the U.S. Geological Survey (Grant # 14-08-1110-G-173). A preliminary report on the kaolin and bauxite resources of the district has been placed on open file at the U.S.G.S. in Reston, Virginia; the Georgia-Geological Survey in Atlanta, Georgia; and Georgia Southwestern College in Americus, Georgia. In addition to a resources estimate, the objectives include the determination of the mineralogical variation, sedimentological parameters, and paleogeographic patterns of the deposition of the high alumina materials and their associated sediments. In the process of compiling data for the resources estimate, isopach maps were developed that provide information as to the shape, size, and distribution of the kaolin deposits and the kaolinitic sediments that contain them. These or similar maps developed for other districts can be useful exploration tools.

Jan 1, 1977