Search Documents

By Todd Loudin

A majority of the chemical process industry uses lime in either a powder or liquid form. Engineering and maintenance personnel often face a long and potentially expensive trial-and-error period in order to find the best process equipment to handle lime. Limestone is mined from a quarry in the form of calcium carbonate (CaCO3). Then, it is crushed and fed into a kiln at approximately 1,093° C (2,000° F), where the carbon dioxide is burned off (calcining) to make calcium oxide (CaO).

Jan 1, 2010

Compagnie Minière Espérance mines a primary gold orebody in an openpit. The ore is processed through crushing, primary gravity concentration, grinding and secondary gravity separation, generating tailings with remaining fine gold. Analysis of the material in the pond has indicated a residual gold grade sufficient to justify a chemical treatment process to recover the gold. However, direct cyanidation would require a prohibitively large installation for the site, which is located in a remote rainforest environment. It was decided to test the feasibility of preconcentration using flotation. As lab tests proved up the technical feasibility of the flotation process, an on-site pilot operation was carried out to assess the continuous circuit performances, define the best configuration and obtain enough data for industrial circuit sizing. Data collected during the pilot campaign was used for calibrating a process simulator built with the USIM? PAC software. The simulator validated the feasibility of upgrading the existing plant, including the reprocessing of tailings to obtain an acceptable fine gold recovery from a small amount of concentrate.

Jan 1, 2010

By B. Stewart, J. R. Warneke

The productivity of underground mines has increased dramatically since the introduction of continuous miners. A variety of new hazards have developed as a result. In the spring of 2004, Mine Health and Safety Administration (MSHA) held a workshop to brainstorm ideas to decrease the number of injuries associated with continuous miners. One of the main areas of discussion at the workshop was “trailing cable-handling injuries.” The method of handling the power cables over the years has changed very little while the technology and uses of continuous miners has advanced dramatically. This paper will discuss the main ideas brainstormed at the MSHA continuous miner (CM) trailing cable handling workshop and the history and root causes of cable-handling injuries, as well as proposed ideas developed at the National Institute for Occupational Safety and Health (NIOSH) to alleviate some of the cable handling issues.

Jan 1, 2006

By James F. Fraser

Construction of a major linear project in any environment is difficult, at best. Construction of a major linear project which includes major subway elements, both cut and cover and tunneling, in the center of an urban environment, approaches the impossible. I believe such a project would be impossible for a private company or a privately owned utility for a variety of reasons. The major two reasons are the funding necessary for such massive projects and the myriad of individual interests associated with private ownership of land. Such projects are possible in the public sector only because the need for the project... as is the case with mass transportation in Atlanta. . .overrides the profit motive. Without the profit motive, private companies, whether utilities or not, are precluded from practical interest in the development of any project. While it is safe to conclude that a profit-oriented business would have no practical interest in developing such massive projects as may include major tunnels, it would be useful, I think, to compare some of the significant differences between private profit-oriented businesses, and an agency, or Authority, such as MARTA, in building a major linear project. SLIDE 1. Comparison of a Private Company and a Public Agency [Item Private Company Public Agency Simplified To make a profit To provide a pre Purpose scribed service]

Jan 1, 1979

By D. Royston

Curved pulp lifters have been incorporated in SAG and AG mills in Australia. The aims have been to ensure complete discharge, at high throughput, of both slurry and coarse solids, especially at high mill rotational speeds. Curved pulp lifters can overcome incomplete discharge and back-flow of solids down the pulp lifter that can occur in straight-radial pulp lifters (and is a major cause of wear). They can be designed to prevent reverse flow of pulp via grates back into the mill. Experience with curved pulp lifters now extends to three years over three mills, in one mill as an installation from new and two as retro-fitted installations. Curved pulp lifters, relative to conventional designs, offer improved discharge and wear performance and well as high impact-resistance and wear life of the curved pulp lifter grates.

Jan 1, 2000

By William Cass, Ellen Caftel Turcotte

The Elliot Lake Centre was established in 1965 as an independent Centre for Continuing Education offering a variety of adult education services. In 1976 all retraining and community college type activities were transferred to the Sault College of Applied Arts and Technology which had opened a branch campus in Elliot Lake. Upon the completion of this transfer, the Elliot Lake Centre was then contracted in 1977 by the Canada Centre for Mineral and Energy Technology to study the feasibility of establishing a research and information institute dealing with various health and safety concerns of the uranium worker. By late 1980, a federal charter was granted for the establishment of the Canadian Institute for Radiation Safety, made possible through the cooperative efforts of the Governments of Canada and Ontario, the Ontario uranium mining and refining companies, and the Elliot Lake Centre. On 1 April 1981 the Institute officially began operations. PROGRAM DEVELOPMENT AND COORDINATION In May 1978 the Elliot Lake Centre initiated a voluntary sputum cytology program for uranium workers. This program was financed by the Ontario uranium mining companies: Agnew Lake Mines Limited near Sudbury; Madawaska Mines Limited in Bancroft, and Denison Mines Limited and Rio Algom Limited in Elliot Lake. In 1981 additional funding was granted by Eldorado Nuclear Limited for a small group of employees at the company's uranium refinery in Port Hope, Ontario. Initially in 1978, program participants were accepted according to length of employment, radiation exposure levels (calculated in working level months) and/or smoking history. These restrictions were abolished within a few months and all uranium workers were encouraged to participate. From 1978 to 1979 the sputum cytology program was medically directed by personnel from the Montreal Cancer Institute. Until 1979 all data maintenance for the program was performed manually, however the effort required to sustain the system increased significantly as the number of participants grew. In September 1979 the Division of Thoracic Surgery at the Toronto General Hospital, under the direction of Dr. F.G. Pearson, submitted a proposal to the Elliot Lake Centre to develop a data processing system to help coordinate the surveillance program. In October 1979, Dr. Pearson became the new Project Director. Director of the Cytology Program is Dr. D.W. Thompson of the University of Toronto who is responsible for all cytologic analyses. Developmental work to establish the new surveillance system was initiated in January 1980 and became fully operational at the beginning of March 1981. The following sections describe the Elliot Lake operations of the sputum cytology program now conducted by the Canadian Institute for Radiation Safety. PROGRAM PARTICIPATION As of 1 September 1981 the sputum cytology program has 518 participants enrolled. Eligibility is restricted only to a willingness to participate and the ability of an individual to produce adequate sputum samples. Each participant registers for the program at the Institute and is given personal instruction on methods of sputum collection. The majority of the participants in this program are employed by the uranium mining industry; some work for firms which are contracted by the larger companies. Many participants are either retired from the work force or receive disability pensions or workmen's compensation benefits. Other participants have been employed in the uranium mining industry and have since gone on to other employment; some work for various federal and provincial governmental agencies concerned with the mining industry. Some participants are referred to the program by their family physicians because of smoking histories and/or various respiratory conditions. A small number of these individuals have never been involved in the mining industry at all. A chart describing program participation by employment is found in Appendix 1. PROGRAM REGISTRATION In the Elliot Lake area, persons interested in registering in the program are required to go directly to the Sputum Cytology office located at the Canadian Institute for Radiation Safety. Each individual is interviewed personally by the Program Officer. For the employees of Agnew Lake Mines, Madawaska Mines and the Port Hope refinery of Eldorado Nuclear Limited, registration is possible during the Program Officer's semi-annual on-sitevisits. Participants are assigned, in chronological order, "program numbers" for easier identification. File labels are color-coded according to place of residence or, in some instances, place of employment. Each file is stamped with the date each sample bottle is distributed. A file contains: all original test results, a completed registration

Jan 1, 1981

By Jim Gebhardt

Douglas W. Fuerstenau (DWF) grew up on a farm and in several small communities in rural South Dakota during the depression years, where he learned the value of hard work. Working hard can produce results but being clever and hardworking will give you a bright future. In his later school years, Fuerstenau’s family moved to Rapid City where his intellectual curiosity and capacity helped him graduate with a B.S. in Metallurgical Engineering from the South Dakota School of Mines and Technology in 1949. His technical interests led to graduate studies and completion of a master’s degree from the Montana School of Mines in 1950 and Sc.D. degree from the Massachusetts Institute of Technology (MIT) in 1953.

By E. W. Hawk

he power generation industry may be required to reduce carbon dioxide (C02) emissions if regulations related to global climate change are enacted. Coal-fired generation emits more than 80% of the power sector CO2 and would be a likely target for CO2 reductions. Compliance with the Kyoto Protocol will require a 33% reduction from the projected year 2012 emission level, even with moderate load growth. This article describes an analysis of power industry CO2 reduction options and their costs. It assesses how a generator would make compliance decisions under a mandatory CO2 emissions reduction program. Carbon sequestration, fuel switching and new plant construction are considered. The Global Climate Change Treaty signed at the Rio de Janiero Earth Summit in June 1992 set the long-term goal of stabilizing CO2 concentration in the atmosphere. The December 1997 Kyoto Protocol established short-term mandatory targets for the United States and 37 other developed countries. The United States' target is a 7% decrease by 2012 from the 1990 "greenhouse gas" level. Developing countries are exempted from reductions, according to the Kyoto Protocol, despite projections that indicate a significant increase in their emission levels. The Kyoto Protocol must be ratified by the US Senate. US power industry carbon emissions were 490 Mt (540 million st) in 1990 and are projected to be 680 Mt (749 million st) in 2012, according to the US Energy Information Administration. Coal-fired generation emits more than 80% of the power sector CO2. Assuming that the power industry is only required to reduce emissions by a proportional share, a 33% emission reduction, or 225 Mt (248 million st) of carbon, would be required to comply with

Jan 1, 1999

By M. Argiantopoulou

In today?s mining environment, improving production, performance, productivity and profitability is crucial. Production, ancillary, plant and shipping equipment need to be monitored and controlled by online systems delivering production statistics and real-time information to everyone involved, including equipment operators. Traditional systems currently in use today, operate in an iterative mode constantly switching between scheduling and execution. However, the real world tends to change in ways that invalidate such advance schedules. Agent based computing has been hailed as the most significant breakthrough in software development and the new revolution in software. Agent systems are being used in an increasingly wide variety of applications, including complex mission critical systems such as Air Traffic Control. This paper presents the possible ways that multi-agent systems can be applied to mine production and rehabilitation scheduling problems with focus on real time fleet management, plant and equipment performance monitoring, downtime and delay reporting, stockpile management, personnel and equipment tracking and product distribution and transportation.

Jan 1, 2006

By S. Mertikas

The purpose of this paper is to set the stage for (1) the determination of the specifications and actions required for a successful development of a system for the management of waste deposits and contaminants resulting from activities in the mineral industries and landfills and (2) the appropriate infrastructure to be developed at the industrial level. The design of this system would be such that its application could be extended to other industries as well. Waste deposits and contaminants from activities in the mineral industries and landfills commonly cause damage to the environment. In addition to precautionary measures aiming to protect against environmental impact, early warning and immediate response to mining hazards and contaminants is a requirement for sustainable development. Hazard detection and control requires continuous and real-time detection techniques, as well as methods for tracing and predicting the motion of contaminants and waste products. The efficient accomplishment of these goals in the minerals industry requires developing an integrated system for environmental monitoring using remote sensing technologies, in combination with advanced image analysis and geostatistical techniques.

Jan 1, 2003

By Stanley W. Ivosevic

Introduction Increasing investor and industrial demand for gold is not being matched by new mine output from traditional sources. This forces the exploitation of alternative natural and industrial resources to supplement traditional sources. A traditional natural resource is either high- to medium-grade ore, of gold or silver with coproduct gold. Or, they are medium- to low-grade base metal ores having byproduct gold. Traditional ores are also frequently extracted at relatively great expense by selective underground mining. Alternative natural resources include low-grade, near surface ores and the products of mining-dumps - and of onsite processing - tailings. Traditional industrial resources are newly mined gold or that obtained from plant sweepings. Their alternative analogues include gold in old scrap and chemical sludges and precipitates, notably those incidental to the electronic industry. These alternative gold resources have several attractions. They are untapped and abundantly available. Having been overlooked by prior metals suppliers, title to many alternative resources is easily acquired. Or, the value of such a resource may go unnoticed until its gold is rendered exploitable by an advance in extractive technology or an other approach. This article addresses the effect of large tonnage, low-grade lode ores on gold supply. Exploiting these ores is rendered commercial by their amenability to bulk mining by modern large-scale mining and metallurgical operations requiring little selectivity. Placer gravels, perhaps the earliest type of gold ore mined, also are bulk minable. But these fall outside the definition of being lode deposits. Most lode bulk mining is from surface open-pit mines. Some, however, is from underground by such large-scale mining techniques as room and pillar, vertical crater retreat, and end slicing. The low-grade gold ore being discussed averages 2.8 g/t (0.082 oz per st). Output How greatly do bulk minable, low-grade resources effect supply? 1982 was a somewhat healthy year for gold mining and exploration in North America in spite of the general depression in the mining industry (Table 1). The wildly fluctuating price of gold bullion had stabilized at an annual aver¬age of $12.08/g ($376 per oz) - (Handy and Harmon base price). Half of the 1.3 kt (43 million oz) of 1982 world gold mined were from South Africa's high-cost, medium-grade, selective underground mines. Of the remaining half, 20%, or about 130 t (4.2 million oz), was mined in North America. This includes Canada and the US - the third and fifth largest gold producers in the world. Of that North American production, more than 62.2 t (2 million oz) of gold, or about 50%, came from bulk mining of gold ores with or without co-product silver. Most of this was in the US, where bulk minable gold-silver lode ore produced nearly 31 t (1 million oz). This amounted to 60% of the nearly 46.6 t (1.5 million oz) produced in the US during 1982. An additional nearly 7.7 t (250,000 oz) of gold were produced as the byproduct of bulk mining of cop¬per ore, for a total of 34 t (1.1 million oz) of gold, or 75% of US gold production by bulk mining. To further illustrate this, US placer, mine dump, and related operations produced an insignificant 4% of US gold output at the time. Exploitation of bulk minable gold deposits is becoming increasingly important worldwide. Most new Australian gold mining announcements are of bulk minable developments. This trend will increase in North American mining as more large tonnage, low-grade operations come onstream in Canada, where much current production is from underground. It will increase with the general climb in Mexican gold mining. And it will grow with expansion of the 12 t/a (400,000 oz per year), gold production of the Dominican Republic. Production Metal price and operating costs make these large tonnage, low-

Jan 11, 1984

By E. F. Klein, R. L. Eacret

Introduction In contrast to the general type of crushing mechanism in which the crushing surfaces alternately approach and withdraw from each other, described earlier in this section, and continuous-pressure break¬ers such as rolls and roller mills that will be described in a later chapter, impact crushers load by striking pieces of rock while in free fall and hurling them at high speed against stationary surfaces. Because the impact crusher depends for its effectiveness upon high velocity, wear is greater than in the slower-moving jaw and cone¬type wear parts, and for this reason its use is strictly limited to rela¬tively soft, friable, and sticky rocks that are characteristic of many nonmetallic mineral deposits. A few of these are phosphates, lime¬stone, barite, clay, asbestos rock, and coal. However, several examples of their use on soft lead-zinc and precious metal ores have been known. Although the use of impact crushers is expanding today into the range of ores containing as much as 15-18% silica, Taggart16 set the practical limit at 5%, and in the 1940s and 1950s several installa¬tions in the US and western Europe exceeded the limits of economical maintenance and were quickly superseded by the slower-moving, con¬ventional crushers. A rock that tends to be plastic or bouncy in a jaw or gyratory crusher when the force is applied slowly to reach ultimate strength, may become brittle with rapid loading and thus increase the effective¬ness of the applied forces. For this reason it is to be expected that as the quality of hammers, grates, plates, and cages improves with advances in steel technology, the use of high-speed crushers of this kind will increase. Terminology Modern usage differentiates between the impactor and the hammer mill, the former relying primarily on the impact of hammers (fixed or free-swinging) and secondarily upon pieces striking one another or steel surfaces; the hammer mill relies on both the centrifugal impact force of free-swinging hammers and the attrition and shear action between these hammers and well-placed grates suspended at the bot¬tom just below the hammer circle. The hammer mill, because of its grate discharge, restricts discharge of oversize rock to the grate open¬ing, while at the same time providing a trap for removal of tramp iron or other uncrushables. The impactor discharges free, so generally works with a screen to control product sizes. The question of terminology, impactor vs, hammer mill, creates difficulties because the similarities appear to outweigh the differences by far; if one were to list the similarities in order of importance and then the differences, he would be forced to conclude that they would best be dealt with as a single kind of crusher. Taggart16 gave it four names and added "as it is variously known," but it must be remembered that in 1945 the machine was nearly exclusively of the flailing-hammer type, while today the fixed-hammer rotor is also com¬mon. In this chapter the terms impactor and hammer mill will be used where they seem to apply. It is perhaps unfortunate that this terminology is being confused with rock breaking at the mine, usually with hand-held tools, e.g., the article "High-Energy Impact Rockbreaking" by Grantmyre and Hawkes, CIM Bulletin, August 1975. General Description Impact breakers, impact crushers, and hammer mills accomplish material breaking and reduction primarily through impact action of the material with fixed or free-swinging hammers revolving about a central rotor. The material to be crushed enters through an opening at the top or top side known as the "feed opening" or "hopper opening" and falls into the path of rotation (hammer circle) of the hammers. Initial breakage is accomplished in midair by collision of the dropping feed material with high-speed hammers. The second stage of breakage occurs when the pieces hit plates or breaker bars which line the crusher boxlike frame. Hammer mills rely further on a shearing and attrition action between free-swinging hammers and grid bars or grates at the crusher bottom which restrict discharge of oversize material until it is broken sufficiently to pass through the grid opening. The term hammer is used in reference to the piece which strikes the material, whether it is fixed on the rotor or free-swinging. It

Jan 1, 1985

By ERIK CHARRIER, ADITYA JUGANDA, Jürgen Brune, Gregory Bogin, Patrick Maier

Confined explosions are a major risk in underground coal mine operations. Depending on confinement, ignition location and obstacles in the flame path, methane explosions can transition to detonations. This research focuses on explosion experiments in a reactor with diameter of 71 cm and length of 30.5 m, along with developing the corresponding computational fluid dynamics (CFD) model that captures the observed flame behavior. The results show that the 2D and 3D CFD models are able predict the experimental flame front propagation velocity, but the 3D model shows more explicit conformity than the 2D model.

May 1, 2024

By Michael Elliot-Jones

The fundamental competitive structure in world coal markets will be modified by the entry of such new participants as Colombia and the newer mines in South Africa. The US will, in most markets remain the swing producer, although a number of low cost US mines will continue to compete in world markets. Exchange rate swings will persist as a major hazard for coal exporters.

Jan 1, 1986

By A. B. Holland-Batt

In the 1960s and 1970s, incremental development rather than innovation was the norm for gravity separation. However, the last 15 years have seen a number of new developments in this area. The article reviews the traditional gravity-separation techniques and then examines the newer developments such as centrifugal separators. Emphasis is placed on novel devices or improvements that offer better control or improved performance.

Jan 1, 1998

By John Frostiak, Don Welch, David Landriault

The use of paste technology for underground cemented backfill is widely accepted in the mining industry today as a potentially cost effective alternative to cemented rock and hydraulic slurry fill. While paste backfill is not the appropriate backfilling method for all mines, there are presently 23 operating tailings paste backfill plants throughout the world. This new technology has gained increasing acceptance as a backfill method over the last decade and its use is now expanding into the surface disposal of tailings using the stacked, thickened tailings disposal concept. Over the next 18 months there will be ten new paste plants commissioned in the world. Five of these ten plants will be used exclusively for surface tailings disposal or a combination of surface disposal and underground backfill production. The thickened tailings disposal concept, developed by Dr. Eli Robinsky in the early 1970's, has been in use for decades at several mine sites throughout the world (Kidd Creek Mine site in Northern Ontario), but always utilizing non segregating high density tailings slurry central discharge, stacked tailings placement. With the use of a higher solids content paste, the typical 2-degree beach angle can be increased to ten degrees or more with no runoff water and minimal shrinkage crack development through desiccation. This paper presents the design of the first mine to implement true surface paste disposal, Barrick Gold Corp's Bulyanhulu Mine in Tanzania. The paste system will be commissioned in the first quarter of 2001 allowing performance data to be collected to define the full potential of paste technology for surface tailings disposal.

Jan 1, 2001

By Priscilla P. Nelson, Francis L. C. Fong

Introduction Fracture mechanics is the study of the behavior of cracks and their modes of propagation. During cracking, energy is consumed in creating new surface area. The more energy a material absorbs, the higher is its fracture resistance. This fracture energy is provided either by work done externally, by the release of elastic strain energy within the cracked body, or by a combination of these two effects. Fracture resistance is measured in terms of either the stress intensity factor, K, or the energy release rate (also referred to as crack driving force), G. For linearly elastic materials, these two quantities are related by the following equation: [ ] where [u] is Poisson's ratio and E is the modulus of elasticity. Both K and G are direct functions of the applied force and the crack length. The process of rock cutting with full-face tunnel boring machines (TBMs) involves the indentation of a rock surface by rolling disc tools. Excavation occurs as fractures, extending from the locus of chip indentation, propagate between concentric disc grooves and liberate rock chips from the intact rock face. Since disc cutting is achieved by a fracture process, it is logical to anticipate that differences in cuttability of a variety of rocks should be related to the variation of fracture material properties among the rocks. Such a relation has been demonstrated between the performance of full-face TBMs and the critical crack driving force for excavation in relatively high strength, brittle, low porosity, isotropic rock (Nelson et al., 1985). The objective of this paper is to report on the results of a continued investigation of the relationship between fracture material properties and the effectiveness of disc cutting. Additional reliable data on full-face TBM performance is difficult to obtain, so that the results of disc linear cutter tests performed by the Transport and Road Research Laboratory (TRRL) (U.K.) are utilized in this study. Fracture Material Property Evaluation If a crack tip is subjected to a perfectly plain strain condition, many materials will behave in a brittle manner, and the material resistance to fracture is constant during crack growth. This resistance is referred to as the plain strain fracture toughness, believed to be a material property. The standard testing procedure for this parameter is given in the American Society for Testing and Materials (ASTM) test designation E399. To ensure plain strain conditions, acceptable specimen geometries are specified. Unless these geometric specifications are adhered to, the measured fracture resistance is regarded as the apparent fracture toughness, and a subscript Q is used, as [ ]. The methodology adopted by ASTM E399 is within the framework of Linear Elastic Fracture Mechanics (LEFM). This approach assumes that material resistance against cracking is developed instantaneously, without initial stable or subcritical crack extension. Prior to crack advancement in rock, however, much of the crack driving energy is absorbed in a localized volume in front of the crack tip, referred to as the plasticity or microcracking zone. This capability for energy absorption substantially increases material resistance, and a crack may be arrested unless an increased crack driving force is applied. The LEFM or plain strain assumptions would underestimate the actual fracture resistance of such a material. Such a conservative approximation may be desirable in the design of structures against fatigue or brittle failure. In mining or tunneling, however, an underestimation of crack resistance can lead to the selection of underrated excavation equipment and a decrease in production efficiency. The development of fracture resistance in rock is best described by the material resistance curve, or R-curve, which is a plot of fracture resistance as a function of crack extension. Typically, peak resistance is only reached after a finite amount of subcritical crack growth. The

Jan 1, 1986

By Yi-Hsuan Chen, Jürgen Brune, Candace S. J. Tsai, Alejandro Munoz, Connor Krause

This study highlights the significant presence of submicrometer- sized airborne particles in underground coal mines, especially around the belt conveyor drift areas. Using realtime instruments and gravimetric samplers, the assessment revealed that particle concentrations were notably higher in the belt entry compared to other locations, with a strong presence of submicrometer- and nanoparticle-sized dust. The study’s findings emphasize the importance of addressing small particle exposure, as these particles, composed of harmful substances like calcium, copper and iron, can pose serious health risks to miners. This research emphasizes the importance of improving air exposure estimation through more effective monitoring and characterization techniques to better understand and reduce workers’ exposure to hazardous airborne particles in the mining environments.

Apr 1, 2025

By Arnolfo A. Valdivia

Prior to 1971, there were several clinical trials to evaluate programs for early detection of lung cancer. Among these, the Philadelphia Pulmonary Neoplasm Research Project,(3) the Veterans Administration Study published by Lilienfeld,(7) and the controlled trial of the Kaiser Foundation Health Plan showed an overall five year survival rate of 8% for newly detected cases (the same as the national statistic for unscreened patients). In 1971, the National Cancer Institute initiated three randomized, controlled mortality studies using lung cancer screening of persons at high risk (male smokers over 45 years old). The studies are being conducted at the Johns Hopkins University Hospital, the Mayo Clinic, and the Memorial Sloan-Kettering Cancer Center. The studies have slightly different designs in the combination of sputum cytology and chest x-rays. At the Mayo Clinic the study group is offered screening with sputum cytology and chest x-rays every four months, whereas the control group is advised to have an x-ray and cytology every year. No reminders are sent, and it is believed that only about 20% of the control group is screened. At Johns Hopkins and Memorial, both experimental and control groups are offered annual chest x-rays. The experimental group is additionally offered sputum cytology every four months.(5) At present all of the programs show that screening can detect cancers that are undetectible by other means. However, at this time mortality rates in the control and experimental groups are not significantly different in any of the three studies. OUR PROGRAM Our clinic is located in Grants, New Mexico and we provide most of the pre-employment physical examinations for the mines operating in the Grants area (Kerr McGee Nuclear, Homestake Mining, United Nuclear, Western Nuclear, and Ranchers). In the examinations, we obtain the previous mining history of the worker, a chest x-ray, a sample of sputum for cytological examination, and a blood sample. We also provide routine annual physical examinations of the workers, with special interest in the detection of bronchogenic carcinoma. In the early seventies, we did not have a definite surveillance program. We did not know whether we should have a program like the one started at Memorial or like the one started at the Mayo Clinic. After long consideration, we decided to have a program that does not demand a sputum cytology and chest x-ray every four months, but that allows as many chest x-rays and sputum cytologies as needed to diagnose lung cancer as early as possible. We believe that, if a screening method for cancer is to be optimally effective, it must detect the process at stages early enough for curative therapy. We order a test depending on the age of the miner, the race, the mining history, the smoking history, the radiation exposure levels, and the results of the previous chest x-ray and sputum cytology. With the help of the computer, we have a list of all the miners who should be watched closely because of age, race, mining history, smoking history, radiation exposure, etc. Examination of the miners is performed at our clinic, where all the records are kept. The sputum is collected there but examined in Grand Junction, Colorado, by Dr. Geno Saccomanno. There are two ways to collect sputum. The best way is to collect three consecutive morning samples. For this, we need the cooperation of the miners. They have to follow these instructions and mail the bottle containing the sample to Grand Junction. "Instructions for obtaining a good cough specimen" The enclosed plastic bottle contains a preservative solution, so do not empty out the liquid in it. When you go to bed, place the plastic bottle at your bedside where it will be handy in the morning. When you first get up in the morning (before breakfast) try to cough up some "phlegm" from deep in your chest, and spit it into the liquid in the bottle. Try coughing several times. If you have difficulty coughing, try inhaling deeply the steam from a teakettle (or home-type inhalator). Keep the amount of saliva (ordinary spit) that you put into the bottle along with the cough specimen as small as possible. Do not collect the "phlegm" or mucous that comes from the back of your nose. Put the cap back on the bottle, and shake it vigorously for two minutes. If the amount of material you have coughed up is quite small, then keep the bottle at your bedside for three or four days, and each morning try to add another cough specimen. After obtaining your cough specimen, repack the bottle in the mailing container, and attach the enclosed mailing label. It does not require any postage stamps. Unfortunately, some miners "forget" to mail the sample and end up with an incomplete physical examination. To avoid this some companies, like Homestake, request that we obtain the sample in our clinic by forcing cough and expectorant with a nebulizer machine. This method does not give as good a sputum sample as the previous one, but we do get a sputum sample for every miner. The policies of different companies, in regard to annual physical examinations are different. All

Jan 1, 1981

By Y. FUJII, E. CHANDA, J. KODAMA, D. FUKUDA, M. NISHIHARA, Y. NAKAYAMA, P. SINKALA

This paper describes a creep damage model that was proposed to clarify the rockburst mechanism for the Mufulira underground copper mine in Zambia. Cumulative rock damage was evaluated for the edge elements of each sidewall of the mining drives based on normal stresses by the 3-D displacement discontinuity method (DDM) (Crouch and Fairhurst, 1973). The rockburst occurrences were well hindcasted.

Jan 1, 2023