Search Documents

By Roy Eric Lurie

Computer based signal processing techniques for obtaining empirical dynamic models from measured mill circuit data are discussed. This modelling is the first step towards designing a particle size control strategy. Experimental data from a computerized acquisition sys tern is examined and analysed, and a number of model identification procedures are applied. The resulting models are compared and a suitable model is selected, illustrating the benefits of computer tools for control system design.

Jan 1, 1992

By Wei Wu

A computer-aided method for optimization of bench blast design in surface mines is presented. The design procedures basically consist of two steps. Firstly, a series of normalized, full- scale bench crater tests must be carried out in the field to find the optimum burden that produces the largest amount of acceptable fragments and other parameters that defines the effective fracture zone. Next, the locations and initiation sequence of blast-holes will be determined in such a way that each hole, at its time of firing, will be responsible for same amount of burden rock and will be in a position favorable to effective fracture of burden rock. A computer software "B.B." which can assist the second step of the design is fully introduced and its application is illustrated by an example.

Jan 1, 1992

By Louis W. Cope

The Compañía El Zapote Yacimiento Y Minas, S.A. has an ore body containing 650,000 tons of 0.185 oz/t gold ore in Mexico. Metallurgical testwork has been done to determine the response of this ore to several possible processing schemes. The paper describes the rationale for selecting the Silver State Mining Co. methods in Colorado. Plans for developing the mine and building the treatment plant are described in detail in the paper. Estimates of capital and operating costs are included.

Jan 1, 1984

By Graham Swan, Richard K. Brummer

The paper begins by describing an underhand cut-and-fill mining concept for a 50m thick, generally tabular though irregularly shaped orebody dipping at 30 degrees and occurring at a depth of between 2300 and 2700m in the Sudbury Basin. From this, the broad design requirements of a fill system are stated. Two and three-dimensional numerical models are then described which were built to evaluate the theoretical benefits of different types of fill reinforcement. Included in this evaluation are the effects of span, fill strength, fill tightness, as well as static and dynamic loading types. Results, supported by large-scale physical models, are presented to show the significance of reinforcement on stable, undermined fill performance. Finally the paper describes work which has been done to evaluate the suitability of so-called silicated cemented backfill. This system is, in principal, attractive for deep mining applications since transportation is in the "safe" hydraulic regime, while fill water run-off, segregation and shrinkage effects are potentially eliminated in the stopes. The results from various surface and underground trial pours are reported which substantiate the proposed use of this type of backfill at depth.

Jan 1, 2001

By Robert M. Rowe

Among the increasing operating costs affecting today' s processing facilities are those necessary in meeting the continually growing requirement for safe and environmentally sound materials- control and handling procedures. Of particular interest are materials listed as hazardous, the need to maintain accurate records of their acquisition, consumption and disposal, and the obligation to employees and the community to have information available regarding such materials. Some requirements affecting modern operating facilities are reviewed in this paper, and potential methods for dealing with complex handling and documentation requirements, including computer automation, are discussed.

Jan 1, 1991

By Manfred Hager

The ability of conveyor belts to transport large mass throughputs economically over previously unprepared ground has resulted in this system achieving great and extensive use. A significant component in this development is the conveyor belt itself. The development of high strength steel cord conveyor belts involves the optimising of splice design, the use of excellent rubber material especially in the splice, good craftsmanship during splice production and modern field vulcanisation equipment. The durability of a splice for belts of class St 3000 up to St 790 is expressed by the fatigue strength under dynamic stress. The results obtained with a test method and equipment developed by the University of Hannover indicate the present state of the art in this field. Belts of high nominal strength used on inclined long distance conveyors reach splice fatigue strengths of about 3000 N/mm. The design should only exploit approximately 50% of the fatigue strength determined in the tests as maximum operating stress. IMPORTANCE OF CONVEYOR BELT SYSTEMS The use of conveyor belt technology has expanded considerably over the last decades in the bulk goods transportation sector. Because of the favourable transport costs and the technology's adaptability to specific topographies, belt conveyors frequently represent the most economic solution. When flows of goods are large, as in German lignite mining operations, where masses of up to 40,000 t/h are given, it is the only technically feasible alternative. The use of belt conveyor systems allows the sensible distribution of the waste and the production of the coal (Hager, 1981). But this transportation alternative is also suitable when the masses involved are smaller. Whereas conveyor belts were only suitable for loose bulk goods up until a few years ago, today they are frequently also used for hard rock open cast mines, e.g. in the production of copper ore. Because of the favourable transport costs it is frequently still economic to use mobile crushers with a throughput of up to 10,000 t h 6 which breakdown the large blocks produced y explosives into transportable grain sizes. In many operations, trucks are only used to provide flexibility between the excavator and the crusher, i.e. over short routes, and the long, frequently steep, transport paths to the processing plant or to the spreader are undertaken by belt conveyors (Einenkel et al., 1992). The advantages of belt conveyors, i.e. to cope with large mass flows over inclines and down slopes of up to 1:4 have resulted in this system gaining very extensive use throughout the world. The conveyors can be installed over for the most part unprepared ground with suitable vertical radii, adapted to the locally available belt material. In the process individual conveyor belts with lengths of up to 15 km, and in the underground sector with lift heights of up to 1 km, have been built and operated. This great variety of application possibilities is complemented by a limited ability to pass through horizontal curves. This can be achieved with the help of design measures on the conveyor whilst bearing in mind the characteristics of the belt. STRESSING OF CONVEYOR BELTS IN DIFFERENT TYPES OF PLANT The advantage of conveyor belts compared with other systems is also to be found in the large available service-time window, i.e. the excellent reliability and the low costs of energy consumption and maintenance. It is in particular the reliability of a belt transport system which depends to a great degree on its main component, that is the belt - in all its different types and variations. For this reason, the belt is also given the greatest attention in the development of the individual components, because it is the belt which must be designed optimally with regard to various factors. The specific properties of the conveyor belt then assert a considerable influence on the design and sizing of most other components in a

Jan 1, 1993

By Michael L. Nave

Belt Conveyors are an important method for transportation of bulk materials in the mining industry. The control of the application of the starting torque from the belt drive system to the belt fabric affects the performance, life cost, and reliability of the conveyor. This paper examines applications of each starting method within the coal mining industry.

Jan 1, 1993

By P. Diehl

The increasing public interest in a useful framework for an assessment and classification of mineral resources (1) is documented by the recently published international classification scheme of the United Nations (1979) and the revision of the classification system of USBM/USGS (2) (1980). Moreover, various classification systems are currently discussed by the mining industry. In spite of major improvements in respect of the concepts, definitions, and taxonomy of ore classification, it has been recognized that the recent practice to classify mineral resources does not create truly reproductible results, i.e. an assessment to the various categories which is free from personal bias or corporate interests. Following are geostatistical methods proposed for a standardization and quantification of various terms in ore classification. After critical review of present practices, we will establish a precise link between the classical terms such as "measured", "indicated", and "inferred" reserves and the geostatistical concept of estimation errors. Moreover, we will demonstrate, how the basic criteria of economic feasibility, geologic assurance and recovery can be taken into account by geostatistics. A specific algorithm will be proposed to block out and to classify reserves according to the degree of geologic assurance. . We will also show computerized methods which perform complete classification procedures, and will also exemplify them with typical case studies.

Jan 1, 1982

By P. E. Sperry, J. M. Duncan

INTRODUCTION The purpose of the report on which this paper is based is (1) to evaluate the potential for cost reduction of urban mass transit tunnels by use of alternative materials transport systems during the tunneling process, and (2) to identify research and development program elements to assure that the materials transport system will not become the limiting factor for the rate of excavation. The approach taken was: Review the state of the art of urban tunneling by extensive interviews with representatives of tunnel contractors, equipment manufacturers, government agencies and consultants, and by review of recent literature.

Jan 1, 1979

By M. J. Howes, C. A. Nixon

INTRODUCTION A safe heat stress control strategy for an underground mine has three elements: Application of an environmental measure which reflects physiological strain with sufficient accuracy for the range of conditions encountered underground. Acceptance of a functional relationship between the environ- mental measure and human performance which is used to optimise the environmental conditions achievable with either ventilation or ventilation and refrigeration. A management control strategy based on the environmental measure which is designed to ensure that work in environments where excessive physiological strain may occur is prevented and corrective action is initiated. The environmental measure that reflects physiological strain is the link between the three elements and, since the turn of the century, the discussion of the merits of various indices has been prolific. One problem in selecting a suitable measure or index is the ease with which it can be physically obtained relative to accurately reflecting the physiological strain. For example, wet bulb temperature is simple to measure and, for a particular mining sys- tem, it may adequately represent physiological strain, however, it would not necessarily provide the same relatively safe measure in a different mining system. The acceptance of a measure which can be universally applied has been confounded by both development and predisposition. That is not to say that there is only one "correct" measure and all others are unsuitable. It is self evident that if the application of a particular index has resulted in adequate control, then that mea- sure is correct for that situation. However, an understanding of the limitations is necessary to ensure that adequate control is maintained as mining conditions change. Almost 100 years after the question of heat stress in mines started to be dealt with in a collective manner, an analysis of the available information is leading towards a general strategy to control this problem. In the paper, the developments in heat stress assessment are briefly examined and followed since the earliest published observations on the effect of heat in mines (Haldane, 1905), efforts to determine a relationship between an environmental measure and human performance are reviewed and summarised and the benefits of control strategies such as acclimatisation and shortened shifts are discussed as they relate to Mount Isa Mines. The results of testing the prototype air cooling power instrument are discussed and a heat stress control strategy outlined. HEAT STRESS AND AIR COOLING POWER The operation of the human engine is analogous to other engines where the conversion of chemical energy from the oxidation of fuel to useful mechanical energy is not 100% efficient. In a diesel engine it is about 33% and in a human engine less than 20% resulting in at least five times as much heat produced by the meta- bolic process as useful work done. Metabolic energy production is related to the rate at which oxygen is consumed and is about 340 W for each litre of oxygen per minute. Using measured oxygen consumption and an average body surface area of 2.0 m2, the approximate metabolic energy production associated with different mining tasks is (Morrison et al. 1968):- • Rest, 50 W/m2 • Light work, 75 to 125 W/m2 (machine, LHD or drill jumbo operators) • Medium work, 125 to 175 W/m2 (airleg drilling, light construction work) • Hard work, 175 to 275 W/m2 (barring down, building bulkheads and timbering) • Very hard work, over 275 W/m2 (shovelling rock) Heat balance is achieved when the rate of producing heat (the metabolic heat production rate) is equal to the rate at which the body can reject heat mainly through radiation, convection and evaporation. Heat exchange between the lungs and the air in- haled and exhaled is normally less than 5% of the total and there- fore usually ignored. Any heat not rejected to the surroundings will cause an increase in body core temperature. Since heat stress is related to the balance between the body and the surrounding thermal environment, the main parameters required to be known when determining acceptable conditions are those associated with the heat production and transfer mechanisms. These can be summarised as follows: Metabolic heat production rates (M - W) Skin surface area (A3) (and effects of clothing) Dry bulb temperature (t[ ]) Radiant temperature (t[ ]) Air velocity (V) Air pressure (P) Air vapour pressure (e [ ]) The rate of heat transfer to or from the environment depends on the equilibrium skin temperature t, and the sweat rate S,. These in turn depend on the response of the body to the imposed heat stress and the effect of thermoregulation (Stewart, 1981). Thermoregulation The body contains temperature sensitive structures which send impulses to the brain at a rate depending on the temperature. Both hot and cold signals can be differentiated and the thermoregulatory response ahivated according to which signal pre- dominates. If "cold" signals are dominant, body heat loss is re-

Jan 1, 1997

The concept of optical basicity is now being widely applied to rationalize and predict the chemical properties of slags. It employs signals from a probe ion to indicate the "state" or relative "freeness" of the oxygen ions in the slag, and hence provides a fundamental measure of slag basicity. Values of the bulk optical basicity of a slag can either be measured spectroscopically in samples of transparent solid glassy slag, or calculated very simply and accurately from the chemical composition of the slag. The way in which these values vary in different systems are illustrated as isoptical basicity lines on ternary diagrams, and the patterns obtained are discussed. The difficulties associated with assigning optical basicities to the oxides of transition elements are also reviewed briefly. It has been demonstrated that these bulk values can be used as the basis of a flux control model for steelmaking to achieve end-point chemistries much more reliably. Furthermore, several correlations have been established which allow the prediction of the slag-metal distribution of various solute elements. This approach has been used to predict the phosphorus distribution at the end of steelmaking, and also to custom design fluxes for the ladle and tundish to aid in the control of residual elements in the steel such as suphur, hydrogen and nitrogen.

Jan 1, 1990

By Alan P. Cook

Methane levels have been measured around continuous miners and compared with computer simulations of methane flow. A multi-channel data logger, reading continuously from six methanometers, has shown methane levels to vary at different positions around a continuous miner, with the cutting drum and the immediate face area not necessarily recording the highest concentrations. Methane levels in the driver's cabin are generally low compared with the return side. Computer simulations, using computational fluid dynamics, have been supported by the measured data, and have shown that methane behaviour within the first few metres of the face varies considerably for different bord and pillar development stages. Methane is diluted rapidly to acceptable levels, but the distance required for this is extended when ventilation flow to the face is restricted.

Jan 1, 1995

By Babcock. C. O.

This report presents equations derived from experimental testing to convert borehole pressure cell data from vertical and horizontal cells to the biaxial ground stress changes. While hydraulic pressure cells in boreholes have been in extensive use since 1957, methods of data reduction have been slow to develop. The methods of Sellers (1970) and Bauer et al. (1985), respectively, indicate a linear relationship between cell pressure change and the rock stress change. Lu presented a theory for creep behavior (Babcock et al., 1982). In the present work, in laboratory testing, the logarithm of the cell pressure was related to the stress change in seven elastic materials for a range of Young's moduli of 3.45 to 85.5 GPa (0.5 to 12.4 x 106 psi). The gage response depends upon the setting pressure of the gage, the gage pressure at any time, the rock properties, and the cross-sensitivity of the gage to transverse loading. The setting pressure of the cell should be proportional to the Young's modulus of the rock, the absolute stress can be determined by overcoring in strong rock, and the in situ Poisson's ratio can be estimated in some cases from the cell responses.

Jan 1, 1986

By John A. Herbst, William T. Pate, A. Edward Oblad

Dynamic optimization is a cost-effective means to increase production or improve product quality in a plant. Several model-based approaches to dynamic optimization of mineral processing operations have been developed and implemented in plants. This paper reviews the phenomenological models that are the basis for dynamic optimization and the alternative methods of mathematical optimization. These methods range from theoretically complex and costly to implement to intuitively comprehensible and readily implemented.

Jan 1, 1990

Mine managers need useful data to support production and maintenance decisions; for example, to evaluate the performance of replacement components. Today, managers rely solely on past experience, supervisors, opinions, and time studies. Our paper describes the concepts and algorithms we are developing for an automatic, intelligent decision support system (IDSS) that will aid managers by reducing and analyzing large amounts of, monitoring system sensor data and report only key production and maintenance information.. IDSS contains a pattern recognition, subsystem (IDSS/PRS) prototype to report graphical trends in traditional time study elements. We are designing. and prototyping a knowledge representation subsystem, using Knowledge Craft Tools, that will learn and adapt to the dynamic mine environment and reason about the recognized patterns using representations of manager's knowledge, equipment, capabilities, and mine layout and operating procedures. This subsystem will reduce, large quantities of time study type information to key issues that interest different managers.

Jan 1, 1989

By Nader Shahcheraghi, Verya Nasri, Mehdi Bakhshi, Ali Haghighat

An accidental fire load is one of the major loads considered in design of segmental linings in transit tunnel. Typically, a two-dimensional coupled thermo-mechanical finite element analysis (FEA) is conducted. The conventional approach involves using standard fire curves (temperature-time curves) which can lead to a significant overestimation of fire load and tunnel lining thickness in metro tunnels. The focus of this paper is on the cutting-edge approach, using 3D computational fluid dynamics (CFD) analysis of real train fires in metro tunnels and coupled thermo-mechanical finite element analysis (FEA) to accurately and cost-effectively design fiber-reinforced concrete (FRC) segmental tunnel linings for large-scale metro projects.

Jun 23, 2024

By Lijun Xu, Ragula Bhaskar

The transport of dust particles from a turbulent air stream on to the surface of a mine entry is mainly due to the effect of diffusion, sedimentation and inertial impaction. While the literature in aerosol science contains many references on particle deposition, most studies apply to smooth surfaces in small, short tubes. The deposition data from those experiments may not be applicable to deposition in mine airways that have large areas of rough surfaces and extend several thousand meters. This paper describes the mechanisms of mine dust transportation and deposition, specifically, by estimating the turbulent deposition velocity for coal dust in mine airways. Data from in-mine experiments on ambient dust concentration and dust deposition along a straight entry were used. A statistical model for dimensionless turbulent deposition velocity was developed, and compared with the models developed by other researchers. The model shows that the distance from the dust source is an important factor in the turbulent deposition of mine dust.

Jan 1, 1995

By H. Nematollahi

The comminution laws The grindability of the ores or minerals is an important factor that could not be deduced from their mineralogical characteristics (Testut, 1958). Many theories have been proposed to determine the amount of work required in a comminution operation as a function of the nature of material, size and shape of the minerals before and after of comminution. The most important laws are proposed by Rittinger, Kick and Bond. According to Rittinger (1867), the work is directly proportional to the new surfaces produced during the comminution. Kick (1885) believes that the work needed to produce similar modification is proportional to the volume or mass of the material. Bond, during his 25 years of experience and research, reached to the conclusion that on the average the energy required for a known comminution is between the Rittinger's and Kick's laws (Bond, 1952). According to Bond's Third Theory, the work input is proportional to the new crack tip length produced during the particle breakage, and equals the work represented by the product minus that represented by the feed.

Jan 1, 1994

By J. H. Rowland, A. C. Smith, K. A. Teacoach

Current regulations for fire suppression systems in underground coal mines to protect conveyor belt installations have been in place since the Coal Mine Health and Safety Act of 1969 was enacted. Over time, the coal conveyer equipment being used and ventilation conditions underground have changed significantly, particularly the width of the conveyor belts and the use of belt air at the face. The effect of these new conditions on the effectiveness of suppression systems during a fire is not known. The National Institute of Occupational Safety and Health (NIOSH) conducted a study to evaluate the effect of air velocity, water sprinkler activation temperature and a limited water application time on the effectiveness of water sprinkler fire suppression systems to extinguish large-scale conveyor belt fires. The fire tests were conducted using both new and used 1.8-m-wide, fire-resistant rubber belt that met the Mine Safety and Health Administration (MSHA) flame-resistant requirement specified in Title 30, Code of Federal Regulations, part 18, section 18.65 (also known as the 2G test). Tests were conducted using standard response sprinklers with activation temperatures of 68° C and 141° C at air velocities of 0.5 and 5.1 m/s. Two tests were conducted at both air velocities for each sprinkler activation temperature, one using a new belt and one with a used belt. The results showed that the suppression system was able to suppress the fires in ten minutes to the point that a miner could extinguish it with a fire hose. However, in several of the tests, the fire reestablished itself a few minutes after the sprinkler water supply was cut off and quickly grew out of control. This report discusses the large-scale experimental configuration, the installation specifications of the fire suppression system and the results and conclusions regarding the effect of air velocity, sprinkler activation temperature and limited water application on the suppression system performance.

Jan 1, 2010

By J. F. Rakszawski, Robert P. D'Orazio

The use of cyanide in the processing of gold has been documented for over a century. It is still one of the more effective methods of isolating gold, as witnessed by the fact that in 1987 cyanidation was used in the processing of 91.5% of the gold produced in the United States.

Jan 1, 1990