Search Documents

By H. A. Oliveira, A. Azevedo

Physical and chemical characterization and solid/liquid separation of turbid waters from a river affected by an iron tailing rupture disaster (Gualaxo do Norte River, Brazil) were studied at bench scale. Parameters such as turbidity, pH, surface tension, electrical conductivity, total suspended solids (TSS), particle size distribution (micro- and nanoparticles), and zeta potential were analyzed from samples collected at three different river depths. The results in all samples showed the presence of micro- and nanoparticles, ranging in diameters from 100 nm to 200 μm. Best results for flocculation and settling were obtained at pH 7.5, through an innovative combination of eco-friendly reagents: (i) ferric hydroxide precipitates (10 mg L−1 Fe3+) to sweep (enmesh) the dispersed solids and (ii) gelatinized starch (5 mg L−1 ) to form large flocs. The results showed removals between 90 and 100% of total suspended solids (micro- and nanoparticles), resulting in clear water with residual turbidity < 7 NTU. It is believed that this innovative alternative has a high potential for flocculating and treating the turbid water at Gualaxo do Norte River, assisting the water treatment stations.

By K. Holmberg, D. Herriot

This paper by Mr Mclvor is yet another contribution to the eternal controversy surrounding the benefits, or otherwise, of high circulating loads in closed circuit grinding. Throughout the paper it is difficult to establish whether the author is referring to effects relating to the mill, classifier, or to the overall circuit. Table 1 is put forward as indicating the advantage of operating at high circulating loads. From the two (it would be interesting to see more) product sizing points provided in each case, the conclusions to be drawn are that cases one and two have very similar size analyses. The third case, however, indicates a much flatter curve, that is to say, higher fines production and a very wide spread of size ranges. If the objective of this circuit is to provide a closely sized product with minimum overground slimes to the downstream process, then it would appear to be the less "efficient" by far. No data is given for product pulp densities either. The term "efficiency" should never be used without a careful and clear definition. In this case, "efficiency" is used to express an apparent percentage reduction in operating work index (Bond) from the measured "standard" at 250% circulat¬ing load operation. The Bond calculation is itself based upon

Jan 1, 1989

By TUIJA MONONEN, LUDGER BENIGHAUS, CHRISTINA BENIGHAUS, Virginia del Rio, SARI KAUPPI, JUHA M. KOTILAINEN, JAVIER GÓMEZ, JARI LYYTIMÄKI

The understanding of public debates over mineral exploration and mining largely originates from exceptional situations such as mining accidents of conflicts. Less is known about how mining is portrayed and understood under more conventional settings. What storylines dominate the local day-to-day public debate? This article presents results from a comparative case study focusing on newspaper coverage of mineral exploration and mining in three European countries representing different geological and socio-economic contexts. Newspaper articles from the Geyer-Erzgebirge region in Germany, the Andalusia region in Spain, and Northern Finland are studied. The sample looks into the period between September 2018 and February 2020 and shows that regional newspapers report about mining issues relatively intensively even in the absence of major accidents or other media events causing peaks of attention. The tone of the articles is generally neutral to positive towards mining activities, reflecting the specific local settings, historical experiences, and future expectations. Despite the different contexts of the three countries, there were considerable similarities to the topics highlighted, including common themes of mining revival, mining events and social interaction, history of mining, and damages related to mining. Past, present, and future employment opportunities related directly or indirectly to the mining sector are key storylines. Another recurrent underlying theme is the need to balance environment and safety risks and socio-economic prosperity, typically covered through ordinary disputes among the mining sector, public authorities, regional non-governmental organizations, and local initiatives.

Jul 6, 2021

By D. M. Muir

Thiosulfate offers a non-toxic alternative to cyanide for processing gold ores. The mechanism of leaching gold using ammoniacal thiosulfate solution is driven by the Cu(II)-Cu(I) redox couple and is complicated by competing ligands such as NH3 and S2O32-. It is shown that an understanding of the copper speciation and sulfur speciation is required to optimise this system. This paper presents Eh-pH and speciation diagrams for varying concentrations of Cu(II), S2O32- and NH3 and discusses the conditions under which various copper and sulfur species are stable.

Jan 1, 2001

By Micah Nehring, MEHMET KIZIL, Farzad Sotoudeh, Amin Mousavi, PETER KNIGHTS

Production scheduling in underground mines is one of the most important and complex processes in maximising the economic value of an operation over the life of the mine. Due to increasing energy, transportation, processing and smelting costs and reducing water availability, the extraction of ore deposits through underground operations has become more expensive and challenging. A potential productive and efficient solution to mitigate these issues is to integrate pre-concentration systems into the existing mining system to increase ore grades through a preliminary process of rejecting some waste before sending the ore to the energy intensive mineral processing plant. Further benefit of such systems includes the utilisation of the waste and low-grade material in backfilling of open stopes to reduce the transportation costs and surface environmental impact such as reduction of CO2 emissions and waste transportation. The objective of this paper is to present a new mathematical model to optimise the production schedule of underground metalliferous mining operations in the presence of a pre-concentration system. The proposed model optimises the production schedule and sequencing of stopes within a sublevel stoping operation. The results of this study illustrate the potential economic benefits of using a pre-concentration system prior to a mineral processing operation as a result of increased net present value.

Nov 16, 2023

By J. M. Wempen

Booster fans, large underground fans, can increase the volumetric efficiency of ventilation systems by helping to balance the pressure and quantity distribution throughout a mine, reducing leakage and reducing the total power requirement. However, in ventilation systems that use booster fans there is a potential for system recirculation, the leakage of return air to intake air, and also for localized recirculation near the fan through the bulkhead and airlock doors. Air that is recirculated locally decreases the system efficiency because the quantity of air flow through the fan increases without increasing the airflow throughout the system. To understand the detailed flow characteristics of a ventilation system with a booster fan, two-dimensional computational fluid dynamics (CFD) models were developed using the software Ansys-FLUENT. Though two-dimensional models do not represent the full complexity of the flow dynamics, they do provide a good representation of the flow characteristics and they allow for a qualitative analysis of how the flow dynamics are affected by the system characteristics. The CFD models were used to evaluate how the number of booster fans, the booster fan placement, the location and geometry of the fan installation and the construction of the airlock system affect the flow characteristics and the localized efficiency of the ventilation system.

Feb 27, 2013

By Ronald E. Heuer, Debra L. Virgens

INTRODUCTION Behavior of clay soils in response to tunneling is reasonably well understood by reference to the tunnel stability factor NT = Pz/su (Peck, 1969; Heuer, 1974). With this analysis tool, care must be taken to use a value of clay shear strength which represents the actual mass strength, considering such factors as slickensided fissures often found in stiff and hard clays. Behavior of clean sand and gravel soils is also reasonably well understood. Above the water table these soils must be assumed to act as running ground unless they are known to have significant cementation or have a very dense and angular interlocked grain structure. Below the water table they must be tunneled using some form of groundwater control such as dewatering, grouting, freezing, or internal fluid pressure in the tunnel such as compressed air or a slurry tunneling machine. The internal fluid pressure must approximately balance the external water head. Without such precautions these soils behave as flowing ground and may yield large volumes of water flow into the tunnel. A wide range of very fine sand, silty sand, cohesionless silt, and clayey sand soils exist in nature in a variety of geologic environments. The behavior of these soils in response to tunneling, and guidelines for anticipating their behavior, are not well described in the literature. Because of their content of fine particles, these materials may behave as if they initially have appreciable cohesion and moderate to low permeability. They may exhibit significant standup time, and require tunnel internal fluid pressure (compressed air or slurry pressure) less than the full external water head. It is important to be able to estimate the behavior of these soils when planning construction methods. For example, if the external water pressure is 140 kPa (20 psi), but soil stability at the tunnel face can be achieved as a compressed air pressure of 80 kPa (12 psi), a large cost savings may result.

Jan 1, 1987

By Steve Kral

The mining industry in Colorado faces the same problems the industry faces throughout the United States and the world — record low commodity prices and increasing regulatory and environmental restrictions that seemed designed to curtail mining activities. Despite those obstacles, the mining industry in Colorado still contributes about $8 billion annually to the state’s economy in the form of base and precious metals, industrial minerals, coal and associated service businesses and jobs. So the 300 attendees at the102nd National Western Mining Conference felt reason-ably positive about the industry in their state. The meeting is the Colorado Mining Association’s annual conference and was held at the Broadmoor Hotel in Colorado Springs in November. The theme was “Mining in the New Millennium — Achievement + Innovation = Survival.” Experts from Colorado’s mining industry and abroad discussed the challenges faced by the mining industry as it enters the new millennium. They offered insights into how the industry will operate during the early years of the 21st century and how it will survive low prices and increased regulatory restrictions.

Jan 1, 2000

By A. Yazadni-Chamzini

Considering the nature of open pit mines, harvest volume, it usually is required to remove a lot of waste to access to mineral planned grade. So, one of the most important part of open pit mines design, is waste dump site selection. Many factors are effective in waste dump site selection. These factors are sometimes in conflict with each other. So selecting the desired location for waste dump is a process complex and multi-criteria decision making. There are a variety of methods for decision making under complicated condition, such as fuzzy, Delphi, multi-criteria decision making and Expert system methods can be hinted. VIKOR method, which is one of the decision making multi criteria methods, is useful tool for decision-making. On the other hand with regard to uncertainty in decision-making, fuzzy approach is a useful tool for this purpose. This article has tried to select the best waste dump site in Sari Gunay Gold Mine by Fuzzy VIKOR. The results show that C position has a higher priority than other positions.

Jan 1, 2012

In order to reach a large, untapped reserve of high-quality coal, D8 Cloverlick mine proposed to mine a corridor nearly 2,000 ft deep beneath the Benham Spur of Black Mountain, Kentucky’s highest peak. D8 Cloverlick mine was extracting the Owl seam, but the corridor’s route lay approximately 70 ft above century-old mine workings in the C–(Darby) seam. Adding to the concern, three serious coal bursts had recently occurred in nearby Owl seam workings.

Jan 7, 2020

By James McNally, Adam Stremcha, John MacGregor

With 13.7km of TBM tunneling in Atlanta’s hard gneiss well under way, drill and shoot work continues on several sites throughout the city. In order for the City of Atlanta to meet the consent decree imposed by the federal government, an aggressive construction schedule was a necessity. Construction consists of two deep, large diameter tunnels, four construction shafts, a pumping station, one overflow shaft, three large intake structures, and two connecting tunnels. Due to the multitude of blasting insensitive urban environments, a high standard of seismic and air-overpressure criteria, coupled with time restrictions, was adopted for the project. At any given time, drill and blast operations were under way at four of the seven sites requiring a certain amount of coordination between the TBM excavation, surface work, and the forces of Mother Nature. This paper addresses the challenges faced and the techniques used to safely and successfully complete the rock excavation of the West Area CSO Tunnel and Pumping Station project.

Jan 1, 2007

By Steve Kral

The timing was right for SME to celebrate its 50th anniversary in February as a member society of AIME. The mining industry is in the midst of a commodities boom that appears to have legs. Not only is the demand for metals, construction materials and the like increasing in developing nations, but developed nations have also seen the demand for those materials increase at impressive rates. So, in addition to networking and seeing old friends, attendees at the SME Annual Meeting and Exhibit in Denver, CO. Feb. 25-28, had several reasons to enjoy the week — a healthy industry and their society’s landmark anniversary. This annual meeting was held jointly with the Colorado Mining Association’s (CMA) 109th National Western Mining Conference.

Jan 1, 2007

By J. T. Hollow

The Fort Knox Mine is located in Alaska?s interior, where the average ambient air temperatures range from -24°C (-11°F) in January to 16°C (61°F) in July. The mill processes a free-milling gold ore utilizing both a gravity recovery circuit and conventional cyanide leach/carbon-in-pulp circuits. Mathematical models have been developed to accurately predict the impact of leach circuit slurry temperature on gold leaching, carbon adsorption and cyanide destruction kinetics. Additionally, an energy-balance approach has been used to model the seasonal variations in slurry temperatures throughout the Fort Knox mill. The energy-balance model, combined with the kinetics models previously developed to predict plant performance, was used to justify a tailing thickener installation at the Fort Knox Mine. This paper describes the development of the energy-balance model and its prediction of plant performance assuming a tailings wash thickener to reduce heat loss from the mill. Also presented is an analysis of the post-project plant performance that validates the model and shows that the mine produced an additional 596 kg (19,155 oz) of gold while reducing mill reagent costs by $6,302,000 during the first 38 months of operation.

Jan 1, 2007

By W. G. Pariseau

Conventional barrier pillars in underground coal mines are intended to protect mains and sub-main entries for relatively long periods of time. Inter-panel barrier pillars that may be used in especially deep coal mines, say, below 800 m (2,400 ft), are intended to protect longwall panel faces and adjacent panel entries for the life of nearby panels. Barrier pillar failures have serious consequences, especially when failure is sudden and catastrophic. Design of barrier pillars is thus of considerable importance to safety and efficiency of operations. Locally, failure occurs at the limit to elasticity when stress tends to exceed strength. Strength of rock is stress dependent, so an analysis of stress is central to rational design of barrier pillars. There are several approaches to stress analysis for coal mine pillar design that range from the simplified but popular tributary area method including variations that use empirical definitions of the tributary area (volume) to more sophisticated numerical methods such as the boundary element method and the finite element method. Despite ease of use, empirical methods are limited and always suspect when applied to conditions beyond their scope of definition, while boundary element methods do not generally include pillars in the solution domain. The finite element method is not so restricted and thus is a natural choice for conventional and inter-panel barrier pillar safety analyses. Caving of roof strata certainly affects the distribution of stress about longwall faces and nearby barrier pillars. Conventional wisdom that considers roof strata to respond as cantilever beams indicates the longer the span the greater are loads on longwall faces and face supports. Failure of roof beams, caving, shortens spans and relieves face and support loads. The same view is applicable to barrier pillars in that long roof spans outside of barrier pillars leads to higher pillar loads than short spans. Hence, caving should be beneficial to barrier pillar safety. However, the benefit may be small depending on the extent of caving and only in the form of a slight reduction in overburden weight transmitted to the barrier pillar, especially in case of inter-panel barrier pillars. FINITE ELEMENT MODEL Finite element models for stress analysis in rock mechanics are formulated in consideration of physical laws, kinematics, and material laws. These models meet the essential requirements for equilibrium of stress, satisfy strain displacements relations, and in a general sense, relate stress to strain through material laws, often referred to as constitutive relations. The last may be complex and replete with nonlinearities. A de facto engineering material law is the elastic model in the form of Hooke?s law for linear, homogeneous materials that may be anisotropic. A limit to elasticity is imposed by strength in the form of a failure criterion or yield function that accommodates triaxial stress states. Examples used in rock mechanics are the well-known Mohr-Coulomb (MC)criterion, the popular Hoek-Brown (HB) criterion, and the Drucker-Prager (DP) criterion. The first is linear in stress, while the second is nonlinear. Both do not include any effect of the intermediate principal stress. The last is also linear in stress but includes the intermediate principal stress. All show an increase in the major principal stress at failure with confining pressure. In the UT2/3 finite element programs, the failure criterion Y is a nonlinear, anisotropic form and is also the plastic potential [1]: [YJI=+ 11NYJI=+- (1) ] where N is an exponent, usually 2, and J2 and I1 are nonlinear anisotropic forms of the second invariant of deviatoric stress and the first invariant of principal stress. The form (1) reduces to DP when N=1and isotropy prevails. When Y = 1, the limit to elasticity is reached and plastic deformation is possible. The material constants that enter (1) are all computed from unconfined compressive, tensile, and, in case of anisotropy, shear strengths. These latter strengths may be estimated from conventional laboratory test data. Of course, joints in field-scale rock masses induce different values. How different is often a matter of conjecture. For comparative studies, laboratory rock properties seem adequate. Inelastic, that is, plastic behavior occurs with strain beyond the elastic limit. Strain hardening, ideal plasticity, and strain softening are possibilities. Ideally brittle behavior with complete loss of strength is an extreme form of strain softening [2]. Caving may also be considered as strain softening with a less drastic reduction of material properties. As intact roof strata fail, fall, and form a rubble pile below, a new material is formed with greatly reduced elastic moduli and strengths, say, 1/100th of the original intact moduli and strengths. From another viewpoint, caving is simply a natural cut and fill process. Input for stress analysis by the finite element method includes: 1. Preexcavation stress state 2. Geology (stratigraphic column) 3. Structure (major faults, joint sets) 4. Elastic moduli 5. Strengths, and specific gravities of each rock type 6. Excavation sequence Output from an analysis includes distributions of: 1. Stress 2. Strain 3. Displacement 4. Local factor of safety (element fs) The last is defined as the ratio of strength to stress and in view of the failure criterion (1), is the ratio [fsJstrengthJstress=] where the numerator is the maximum possible value and the denominator is the actual value of the square root of the second invariant of deviatoric stress. This invariant is a measure of shear stress intensity but also reduces to uniaxial tensile and compressive strengths as the case may be. An fs greater than 1 indicates an elastic state of element stress; a value of 1 indicates the limit to

Jan 1, 2009

Traditional fine grinding mills in mineral processing relied on the use of steel medium for particle size reduction. The successful development of the Isa Mill(a horizontal stirred mill with 3000 litres of net chamber volume and 1120 kW rated motor power)adopted a novel product separator design that has led to a major revision of medium use in fine grinding. The Isa Mill separator has also successfully operated with a wide variety of medium types such as silica sands, river gravel, smelter slag, run-of-mine ore fractions and steel shots, with size ranges from 0.5 to 10 mm. A great flexibility of the Isa Mill operations has been achieved for processing a feed as coarse as 120 um to a product as fine as 5 µm. This paper discusses the performance of two inert grinding media used in the Isa Mills in Mount Isa Mines of Australia for processing galena and sphalerite bearing ores to below 10 microns. They are the copper reverberatory furnace slag (CRFS)and the heavy medium plant rejects (HMPR). A methodology was also demonstrated for comparing the medium performance and for scaling up the Isa Mills from a 1.5-litre laboratory batch mill to a full scale 3000-litre mill.

Jan 1, 2000

By John McDonald, Peter C. Raleigh, Christopher Dishlip

This paper will discuss how the construction management team and the contractor working together on the City of Los Angeles, North East Interceptor Sewer project, managed information on a daily basis. Data was synthesized from various sources including: inspection, survey, instrumentation, laboratory and the tunnel boring machine data logger systems to produce state-of-the-art reports and graphics which will become industry standard. Special emphasis is placed on how the data is managed and interpreted in a clear and objective manner, permitting the tunneling processes to be carefully monitored and suggesting appropriate action to be taken by the construction management team and contractor.

Jan 1, 2005

By W. A. Wilkinson

In creating a surface mine design, a complicated series of events may be required to meet both mining and environmental objectives. Envisioning the mine at every step of the operation can greatly assist the engineer to identify design and operational problems that might otherwise go undetected until the field operations reach the problem. Providing operations a visual progression of the mine ensures that critical designs generated by the engineer are understood and effectively communicated to operations. Providing the plan as electronic data to the surveyors and/or on-board GPS systems can ensure successful implementation of the design. This paper discusses using computer technology to generate a virtual mine plan and strategies to consider when communicating a virtual mine plan through electronic and paper formats.

Jan 1, 2002

By Gordon T. Clark, James R. Struthers, Celal Kirandag

INTRODUCTION Project Background The Washington State Department of Transportation (WSDOT) hired the Seattle office of Parsons Brinckerhoff to lead a team of consultants to produce an Environ-mental Impact Study and perform conceptual and preliminary engineering. The pur-pose of the Alaskan Way Viaduct and Seawall Replacement project is to replace the existing earthquake damaged and aging viaduct and sea wall, adjacent the downtown waterfront of Elliott Bay, with structures that have improved earthquake resistance and that maintain or improve mobility and accessibility for people and goods along the existing corridor. With an estimated replacement cost over $4 Billion and construction duration exceeding 8 years, it is one of the largest transportation design projects on the West Coast of the United States today. Seattle, Washington is a city of over 2 mil-lion people in the Northwest corner of the United States. Ever since the Klondike Gold Rush in 1897, Seattle has been considered a departure point to Alaska. Because of this, the street along the waterfront was named the Alaskan Way in 1930. Alaskan Way Viaduct and Seawall The Alaskan Way Viaduct (AWV) carries State Route 99 along the shoreline of Elliott Bay through downtown Seattle and is a vital part of Seattle’s highway system. The viaduct carries approximately 110,000 vehicles per day or 25% of all north-south traffic through Seattle (Figure 1). It is 3.4 km (2.1 mile) long with 3 lanes in each direction and was constructed of cast-in-place reinforced concrete between 1952 and 1956. The wear and tear of daily traffic, salty marine air, and several earthquakes have taken their toll on the facility. Studies in the mid-1990s provided early evidence that the viaduct was nearing the end of its useful life. The viaduct’s increasing age and vulnerability was apparent by crumbling and cracking concrete, exposed rebar, weakening column connections and deteriorating railings. In early 2001, a team of structural design and seismic experts began work to determine whether it was feasible and cost-effective to strengthen the viaduct by retro-fitting it. In the midst of this investigation, a 6.8 magnitude earthquake shook the Puget Sound region (the Nisqually Earthquake, located 56 km (35 miles) from Seattle and deep below the surface) caused moderate damage to the reinforced concrete structure. WSDOT closed the viaduct for inspection and repairs intermittently for several days over a period of several months.

Jan 1, 2007

By Osvaldo A. Bascur

Intelligent systems (IS) technologies have received much attention in a wide range of process engineering applications including process operations. With the revolutionary progress in information and computer technologies applying the latest technologies in metallurgical complexes has become a serious challenge to both management and technical teams. Objects and components are changing the way everyone relates to their computer and networks. Goals of real time performance monitoring includes maximizing the profitability by maximizing production, improving efficiency, attending product quality, costs, maintenance, environmental and safety regulations. Designers must consider the greatly expanded desktop computing, Microsoft object technology, Internet and how to build these systems. This paper discusses some opportunities and challenges using objects, components in designing applications and integrating intelligent systems tools. Two examples using performance equations and IS technologies applied to mineral processing are presented.

Jan 1, 1997

By O. Noirot, H. C. Owens, P. D. Rao, D. E. Walsh, J. R. Mokka

Over a period of seven years (1989-1996) the Mineral Industry Research Laboratory (MIRL) University of Alaska Fairbanks, has investigated the effects of temperature, residence time, and particle size on the degree of low-rank coal (LRC) upgrading for a non-evaporative, hydrothermal drying process, also known as hot water drying (HWD). Three Alaskan LRCs were used in this study: Usibelli coal (Seam No. 4) from the Nenana Coal Field, Little Tonzona coal from near McGrath, and Beluga coal from the Beluga-Yentna field on the west side of Cook Inlet. Replicated, factorial tests were conducted. Experimental results indicate that most of the low-rank coal upgrading via HWD occurs rapidly within the first 10-20 minutes of residence time. Thereafter, the upgrading process slows down and over 100 minutes of additional residence time are required to produce similar percentage increases in coal properties to those achieved in the first 10- 20 minutes. The properties of the hot water dried products were very sensitive to process temperature. Calorific value, carbon and oxygen contents, equilibrium moisture levels and Hardgrove gindabilities all appear to change linearly with temperature within the 275°C to 325°C range.

Feb 24, 1997