Search Documents

By E. R. DeMen

In late 1965 General Mills announced the availability of a new liquid ion exchange reagent, LIX®-64, for the recovery of copper from various solutions, such as dump leach liquors. Acceptance of this material by the copper industry has been gratifying. A number of pilot plants have been operated, and at this writing there are four commercial plants either in operation or under construction. The properties and operating characteristics of this reagent have been described in previous papers.1,2 LIX-64 is quite effective and selective for copper extractions although partially limited in pH ranges, losing extraction efficiency as the acidity of the feed solution increases to below pH 1.0. Also, the LIX-64 content in the kerosine carrier was limited to about 10 volume percent (except for special cases) because of rapidly decreasing phase disengagement rates above this content. This in turn led to large plant capital costs, as the organic flow rates had to be in- creased (rather than LIX-64 content) to extract the copper from high content liquors. This was true in all circuits where the feed copper content ran above 2.0 g/l copper. A reagent was needed which would extract copper from more acidic liquors (or higher copper content liquors) and which exhibited improved phase disengagement characteristics with reagent contents up to 30 volume percent. General Mills is pleased to announce the availability in commercial quantities of a new and improved reagent, L+-64~. This reagent broadens the pH range in which copper can be extracted, and exhibits superior phase disengagement characteristics. The improvement in the reagent has been noted in laboratory circuits, as well as pilot plant runs and commercial operations.

Jan 1, 1970

By ERIK C. WESTMAN, JESSICA M. WEMPEN, DALLAN J. COONS, WILLIAM G. PARISEAU, MICHAEL K. MCCARTER

Safe, efficient underground mining is dependent upon proper pillar sizing. Pillar sizing is typically based on a combination of observation of prior behavior, point measurements, theory and numerical modeling. The actual stress redistribution within a pillar, while assumed for many years, has rarely been imaged. Such imaging can help confirm whether or not theoretical and numerical modeling methods agree with actual conditions within a pillar. This research presents a case study from a longwall mine in the western United States. A two-entry, gate-road yield pillar in the headgate of the mine was instrumented with seismometers and convergence monitoring stations, and was monitored over a period of about six months as the longwall face approached the pillar. In this paper, the stress distribution imaged using seismic tomography is compared to the stress distribution expected from theoretical models, geotechnical measurements and numerical models. The tomography results generally agree with those proposed by theory, convergence measurements and numerical modeling results. The agreement of the methods provides validation for the theorized stress redistribution, and this study provides further evidence that tomography can indicate the redistribution of induced stress within a mined rockmass and is another tool available to ensure that mining is conducted safely and efficiently.

Aug 1, 2022

By George C. Trevorrow

It is a pleasure to appear on this program and discuss a subject which is of particular interest to me. In my regular duties as Safety Director of Bituminous Coal Operators' Association, I am called on by member companies to discuss matters affecting face ventilation. As a member of the Joint Industry Safety Committee, as I will later describe, I have a part in processing requests for the use of auxiliary fans for face ventilation. The use of auxiliary fans in bituminous coal mines for this purpose came into rather wide use in the late. '20's when conveyor mining was introduced. In this application, the equipment consisted of a chain conveyor with a face chain conveyor parallel to the face on which the coal was loaded by hand and, in turn, was discharged onto the room conveyor and thence to a loading point on the entry at the mouth of the room. Another method was to use a shaker conveyor with a duckbill which was maneuvered across the face of the room from which the coal was loaded and transported by the shaker to the loading point. In either case the equipment did not readily lend itself to driving crosscuts or breakthroughs with the result that rooms were driven to depths of 250 or 300 feet without adequate means of ventilating the face area with the main split of air. It was, therefore, necessary to use other means of ventilating this area as the rooms were being driven and during retreat work if pillars were extracted. Auxiliary fans of the blowing type were utilized for this purpose. They were of very small capacity using small diameter tubing. By the time the room was driven half way to its projected limit ventilation was very poor or practically nonexistent. To compound the problem the fan was usually set up at the mouth or neck of the room and in many cases the intake air to the fan was the return air from the room. It is small wonder, therefore, that there is on record 12 cases where auxiliary fans were given as the cause of explosions. In 9 of these occurrences, arcs or sparks from open-type motors or accessory equipment on these fans were given as the primary ignition source. They fell into such ill repute that in a number of cases they were blamed as the ignition source even though smoking was strongly suspected as the primary cause.

Jan 1, 1967

By William H. McLemore

Geologists searching for carbonate rocks suitable for chemical uses traditionally have relied on extensive laboratory testing in order to locate strata or zones that might be suitable for mining. However, when considering the significant time and costs involved in sampling and performing chemical analyses, any exploration technique whereby fewer samples and analyses are needed would be of great value. In other words, if the exploration geologist could "zero-in" on select areas, considerable time and money could be saved. In general, the major-element chemistry of carbonate rocks is determined by the abundance of the minerals present. CaO occurs with CO2 as the mineral calcite, which is the primary mineral comprising allochems, matrix and sparry cement; MgO is found in high-magnesium calcite (many calcite fossil species contain appreciable amounts of MgO in solid solution), dolomite, and chlorite; iron occurs in pyrite and in limonitic stylolites, as well as in chloritic and glauconitic clay minerals; materials containing abundant Si02 are microcrystalline quartz (chest) silt-sized quartz, and clay minerals; and Al203 is found primarily in illitic, kaolinitic, and chloritic clay minerals. The presence or absence of these minerals determines the chemical composition of the carbonate rooks.

Jan 1, 1983

By K. L. Kayler

The Bardon Trimount, Inc. stone quarry in Ashland, Massachusetts was the recent subject of a quarry closure review report. The quarry produces aggregate using standard drilling and blasting techniques. Stone is processed at an on-site plant. Noise monitoring data collected during the closure review indicate that the quarry generally operates within the quiet range. There is a decrease in noise while the quarry is not operating. Levels of dust associated with the quarry are low. Unpaved roadways are the greatest contributors of fugitive dust associated with the mining operation. The quarry cannot be seen from any homes within the town of Ashland, except during the winter months. The visual impact of the quarry on surrounding properties is minimal. Further quarry development is likely to reduce visibility of the quarry from some areas.

Jan 1, 1995

By Aurel Goodwin

I chose the title "Let's Clear the Air" for this afternoon's presentation because it has two meanings, the literal and the figurative. Most of you know what MSHA is. Most of you know what MSHA does. And, for the most part, most of you know why. What I hope to accomplish today is to "clear the air" around our health standards, to clarify for you how MSHA views its congressional mandate under Title I Section 101(a)(6), (7), and (9) of the Mine Safety and Health Act. Asbestos, silica, radiation, noise, welding fumes, carbon monoxide, lead, hydrogen sulfide, nitrogen dioxide - the list of physical and chemical hazards encountered in the metal and nonmetal mining industry is as diversified as the industry itself, possibly even more so. In addition, miners are often exposed to several of these health hazards simultaneously.

Jan 1, 1980

By Steven J. Van Kauwenbergh, Talaat A. B. Lawendy

Batch laboratory-scale beneficiation tests were conducted on four high-iron phosphate samples. These samples included sedimentary ores (Tilemsi Valley, Mali and Tahoua, Niger), a sample from an igneous phosphate deposit (Matongo, Burundi), and a fine-grained phosphatic iron ore processing residue from Chile. The Matongo phosphate deposit occurs as a thick (up to 80 m) residual blanket of P205-enriched soil over solid parent rock (carbonatite and associated rock types). Although the Matongo deposit is an igneous deposit, ore from the deposit can be subjected to beneficiation treatments commonly used to treat sedimentary rocks. The beneficiation flowsheets designed to process these diverse ore types involve attrition scrubbing, size classification, and flotation. At the best flotation conditions tested, phosphate concentrates assaying 32.0%-39.0% P205 and 1.0%-1.5% Fe2O3, were obtained at 64.2%-82.2% overall P2O5 recoveries from run-of-mine (ROM) ores containing 9.2%-28.6% P205 and 5.9%-16.1% F,20,. A cleaner phosphate concentrate assaying 33.1% P205, 1.8% A1203, and 3.3% Fe2O3 at 53.4% overall P205 recovery was obtained from the phosphatic iron ore residue that originally contained 4.5% P205, 8.0% A1203, and 17.6% Fe2O3.

Jan 1, 1993

By JIACHENG XIE, XUEWEN WANG, QINGBAO BAO, ZEWEN YAN

The general application of memory cutting technology to shearers is improving the intelligence of the working face, but it has its limitations. It is only suitable for conditions where the environment of coal seam is changing slowly. It compensates for the cutting height by changing the fuselage attitude, and frequently adjusts the height to control the learning cutting trajectory, but due to the problems of shearer control and height adjustment accuracy, it cannot adapt to and compensate for the change of cutting height in a timely manner, resulting in poor cutting accuracy. This study puts forward a virtual memory cutting method based on prediction of the shape of the armored face conveyor (AFC). The integrated key technologies include generation of virtual teaching cutting curve, height adjustment strategy of front and rear drums, cutting

By J. M. Wempen, R. D. WEYHER, M. K. McCarter

Beam theory is a proxy for the behavior of intact, deforming roof strata above underground openings. Strong, stiff, intact strata have the ability to store significant strain energy when underground openings have large spans, as is typical of longwall operations. When strata fail, they may release some or all of this strain energy. Released energy is partitioned between fracture, thermal and seismic energy. The tensile failure surface in simply supported beams is predicted to be free of shear stress. This prediction and the kinematic inability of crack slip during fracture make significant dissipation of energy by friction unlikely.  In this study, the failure energy partitioning of specimens from the Nugget Sandstone formation is examined. Tensile fractures in specimens were induced using three-point loading tests. Elastic waves emanating from fracture events were recorded using an array of accelerometers. Accelerometers were placed within two crack lengths of the fracture surface, and the acceleration records are similar to strong motion seismic records. Spectral analysis was performed and used to develop synthetic, well-behaved, acceleration signals. Synthetic velocity signals were used to estimate radiated seismic energy generated by fracture. These estimates of radiated seismic energy demonstrate a potential means to constrain the minimum seismic partition. Fracture testing was performed on additional samples to estimate the fracture toughness of the sandstone. Synthesis of this data demonstrates a potential means to constrain a maximum seismic partition. Bounding the seismic partition for this type of fracture event could aid the detection and evaluation of seismicity emanating from longwall operations. Having better information about the location and magnitude of mining induced seismicity within longwall overburdens could lead to better understanding of extraction sequencing and rock behavior in general. These energy estimates also support the hypothesis that dissipation of thermal energy by friction is small in bending tensile failure.

By Thomas B. Faddies

The Trixie mine is located in the East Mining District. Since production began in 1970 over 450 000 tonnes of ore grading 239 grams of silver, 6.9 grams of gold, and 1.2% Cu have been mined from veins in Cambrian Tintic Quartzite. Detailed geologic mapping and extensive sampling are essential for compiling the data base required for efficiently developing and mining known reserves as well as planning exploration and development work. Although the basic techniques used by the geology group at the Trixie were developed many years ago, the reduced activity in underground precious metal mining in the U.S. have made these techniques less familiar to many presently active geologists. The increased activity in precious metals search and exploration again offer cause for the application of these techniques as a prerequisite to efficient exploration, development and production.

Jan 1, 1983

By Stefan Medel

As a pioneer Herrenknecht started in 2018 to automate the production of tunnel lining segments. Since then, many automation processes became state of the art. Robots cleaning and oiling the moulds, hydraulic units opening and closing them fully independently. Artificial Intelligence (AI) controls the works and ensures the quality requirements. Data management has become a massive tool from a simple data collector towards a control and optimization tool. Sensors controlling concrete maturity and supporting the precast team to optimize the concrete mix. These state of the art and new innovations will be presented in this paper.

Jun 23, 2024

Direct force measurements were conducted using an atomic force microscope (AFM) to study the mechanism of copper-activation of sphalerite. The force measurements were conducted between a sphalerite plate and a hydrophobic glass sphere in xanthate solutions of various pHs. The glass sphere may represent the hydrophobic air bubbles interacting with minerals during flotation. The force measurements conducted with unactivated sphalerite in 10') M KEX solutions did not show the presence of hydrophobic force. On the other hand, the results obtained with copper-activated sphalerite at pH 9.2 and 4.6 showed strong hydrophobic forces. However, the results obtained at pH 6.8 showed no evidence of hydrophobic force, which provides an explanation for the difficulty in floating sphalerite at neutral pH.

Jan 1, 1998

By M. Jaramillo

The expanded west pit of the 15 Mta (13.6 stpy) El Cerrejon mine will eventually reach a maximum depth of 270 m (890 ft). Slope-stability evaluations indicated that this depth, combined with structural complexities, would create a serious risk of footwall instability. Stabilization calls for anchoring the footwall by the installation of 9- to 33-m- (30- to 108 ft-) long multistrand steel cable bolts. For each of the 15-m- (50-ft-) high mining benches, a row of bolts is installed with variable horizontal spacing, depending on the dip magnitude. Cable bolting is now standard operating practice, and an estimated 11,800 bolts will be installed during the life of the mine. Results to date have been satisfactory in terms of the stability condition of the bolted slopes.

Jan 1, 1997

By J. Richard Tonry

In portland cement manufacturing, the raw materials axe changed to clinker in the burning operation. Generally the rotary kiln is used for this purpose and involves many processes, including pelletizing and nodelizing. This transformation is called clinkering, and is analyzed as now generally practiced in cement making, from the raw material to the resulting clinker.

Jan 1, 1963

By X. Y. Yu, X. A. Wei, A. Zeng

"The flotation behaviors of diaspore and three kinds of silicate minerals - kaolinite, illite and pyrophyllite - using an organosilicon cationic surfactant as collector were investigated as functions of reagent concentration and pulp pH. The results show that the organosilicon cationic collector QAS122 is a suitable collector for the flotation of aluminosilicate minerals but has weak collecting ability with regard to diaspore, enabling the flotation separation of diaspore from silicate minerals using QAS122 as collector. The flotation of a bauxite ore was then studied in detail. Finally, a reverse flotation separation process was used to process a low-grade bauxite ore. It was concluded that use of the organosilicon cationic collector is effective. A concentrate with aluminum oxide (Al2O3) to silicon dioxide (SiO2) mass ratio, or A/S, of 9.67 was obtained from natural bauxite ore with A/S of 6.07 at pH of around 11. The Al2O3 recovery rate was 81.72 percent. IntroductionChina has abundant bauxite ore resources, but more than 98 percent of the bauxite ores are the diasporic type, with the characteristics of complex mineral composition, low aluminum oxide (Al2O3) to silicon dioxide (SiO2) mass ratio, or A/S, and difficulty of processing. The gangue minerals in bauxite ores are mainly kaolinite, pyrophyllite and illite, containing titanium and iron impurities (Zong et al., 2008). It is known that high-grade bauxite ore, with A/S greater than 8, can be processed directly by the Bayer process (Papanastassiou et al., 2002; Ma et al., 1996). However, Chinese diasporic ores have been processed mainly by the sintering process, which is environmentally damaging and energy intensive. Increasing the A/S of the diasporic ores using a flotation method is needed (Xia et al., 2010).Froth flotation is one of the most widely used processes to concentrate valuable minerals in beneficiation ores. It is particularly useful for separating finely ground ores from their associated gangue minerals. For diasporic bauxite ores, flotation is applied to obtain high-quality material for the Bayer process by increasing the A/S. Direct flotation has been shown to be an efficient method for the desilicating of diasporic bauxite ore (Wang et al., 2004; Xu et al., 2004), but reverse flotation has more advantages for this purpose, including less collector consumption, less foaming product and less effect on metallurgy (Liu et al., 2007; Hu et al., 2003; Hu, 2003; Luo et al., 2001)."

Jan 1, 2015

By O. E. Brown

The measurement principle of the Coulter Counter for particle size analyses is described. The application of the Coulter Counter to cement particle content and size analysis and to the size distribution of clinker from standard grindability tests are described. Methods of calibration, sample preparation and data reduction are presented. The results of the analyses obtained are compared with characteristics associated with performance showing both concordance and non-concordance of test data., Future uses of the Coulter Counter for particle size analysis in research and plant control adaptations are indicated.

Jan 1, 1960

By Michael von Seebach

High-pressure grinding rolls subject the feed material to pressures of 200 N/mm? During this process considerable size reduction and the Formation of flakes occur. This paper describes the basic consideration For design and operating of this type of mill. It is also shown that the particle size distribution resulting from this process is typical for grinding processes but untypical for crushing processes. High pressure grinding rolls are designed in size of up to 2.8 m roll diameter allowing feed material top sizes of 250 mm. The rigid frame, bearing and drive - train design allows a broad application of the high-pressure grinding rolls operating the machine in open or semi-closed and closed circuit for dry and moist feed materials. Operating results show that capacity increases of up to 100 % can be accomplished with this technology. The high-pressure grinding roll also, allows for lower operating and maintenance costs due to energy savings of up to 20 L and reduction of wear to less than 1 76 for dry and less than 0.1 5 for wet grinding. Other advantages of the high-pressure grinding rolls are smaller equipment sizes than a ball or SAG-mill for a given capacity resulting in lower building sizes with reduced capital in- vestment costs.

Jan 1, 1987

By Francis F. Pitard

North America had an Important role in the early development of sampling theories. Unfortunately many progressive ideas were soon frozen into a series of guidelines based on the philosophy that "honest sampling only requires good judgment and practical experience". Such a philosophy appeared to be good enough In the early age of the mining Industry; however, it became quickly necessary to find new approaches. During the last thirty years, Pierre Gy's sampling theory provided tremendous breakthrough in the comprehension of this new science, nevertheless went unnoticed in North America. Sampling always generates complex problems and as the philosopher and mathematician Descartes suggested: "A complex problem can often be dissociated Into a series of several simpler problems, only then you try to solve those one by one". The only way to solve sampling problems is to consider each component of the overall sampling error: components of a continuous model such as long-range quality fluctuations, periodic quality fluctuations, weighting fluctuations; components of a discrete model such as materialization errors, delimitations errors, extraction errors, fundamental errors, grouping errors, and segregation errors. PAST AND CURRENT PRACTICES Many sampling methodologies have been developed, improved, and standardized during the first half of this century. Accordingly, sampling equipment has been proposed, selected, and used by standards committees. Today, there is a tremendous variety of sampling methodologies and corresponding tools offered to anyone with limited experience in sampling and it is very easy for a chemist, metallurgist, geologist or miner to spend considerable money in equipment transgressing the most basic rules of sampling correctness. Sampling stations that never worked properly in modern plants often cause engineers to abandon them and return to a primitive form of grab sampling.

Jan 1, 1986

By William Gleason

"Sometimes it’s the smallest things that make the biggest difference. In the world of mining, erosion can lead to small cracks, which can then lead to bigger problems that, over time, can eventually lead to a catastrophic event. However, when managed correctly, as in the case of the Manefey Slide at the Bingham Canyon Mine in Utah, the damage can be minimized.Numerous industry conferences, technical papers, studies and resources are dedicated to these issues each year, but what is sometimes overlooked is how the erosion of personal ethics can also have life-changing effects.At the 2019 SME Minnesota Conference, April 15-17 in Duluth, MN, two inmates serving their respective prison sentences at the U.S. Federal Prison Camp in Duluth spoke to the conference about how small cracks in their ethical foundations grew over time, eventually leading each man to his new address at the minimum-security facility.The men’s full names were not released and they were introduced as Jeff and Tony. Other than the matching green uniforms, both middle-aged men could have fit in with the rest of the crowd. They are well-educated and articulate whose career paths eroded thanks to greed and careless decisions.Tony, a licensed professional engineer, enjoyed a successful career working in contract oversight for the U.S. Department of Defense. Jeff is a former senior vice president of investments who ran a well-respected investment management team. Both spoke openly about the mistakes they made and emphasized that their crimes were not flagrant violations of the black and white rules but grew from ethical violations that live in the gray area between black and white, and right and wrong.Working in contract oversight for the U.S. Department of Defense (DOD), Tony said he was befriended by a wealthy man who was generous with his money. As Tony told it, a few meals with this man led to a few trips to casinos and eventually to gifts of money. The donor did not ask for anything in return, and at the time, Tony said he did not think that he was doing anything wrong. He admits now that the perception of a high-ranking officer in the DOD accepting gifts is not a good one, as it could be construed as the donor might have been trying to gain favor for future contracts; which is how it was presented in court by the prosecution team."

Jun 1, 2019

By August E. Vandale

I speak to you today on the subject assigned to me, "Subsidence - a Real or Imaginary Problem", as a representative of Consolidation Coal Company (a wholly owned subsidiary of Continental Oil Company). The information I relate to you is our experience in the Pittsburgh Coal Company Division of Consol and covers the Pennsylvania properties and mines with particular emphasis on the mines in the south- western portion of the State or in the immediate vicinity of Pittsburgh, Pa. Mining of Freeport and Pittsburgh seams of coal in the Pittsburgh vicinity dates back over one hundred years. Consol, or its predecessor, Pittsburgh Coal Company, has been actively engaged in mining in the area since Pittsburgh Coal Company was organized in 1900. Pittsburgh, Pennsylvania came into prominence as the Steel City largely because of the vast reserves of high grade metallurgical coal readily available in the immediate vicinity and also because of its favorable river transportation. Early in the 1900's we operated over 100 small coal mines, with operations located in the Counties of Allegheny, Fayette, Washington, Westmoreland. We have also operated mines in Somerset and Greene Counties. Titles in Pennsylvania can be in three estates: (1) title in fee, (2) title to the mineral, (3) mining rights permitting the removal and extraction of the mineral with or without waiver of surface damage. Consol has over the years acquired good legal title to the coal lands purchased from individual farm owners, with good broad mining rights, and in 98% or more of its title has a complete waiver of surface damage or the right to subside the surface land. In the early days of our Company, individual coal farms were purchased from land owners. Many of these titles severed the coal estate from the in fee title and good mining rights with waiver of surface were conveyed in the original severance deed. Thus, minable coal reserves were put together by the purchase of the coal under many individual farms in an area. In the early years, the mines practiced hand dug mining - later going to mechanical cutting with hand loading of the coal. Systems used were entry driving with room and rib panels. We have practiced full recovery mining as far as practical during the years of hand loading, as well as in the later years when the mines were mechanized. Mining system layouts, methods and procedures have changed from time to time to keep pace with improved mining machinery and new inovations, such as roof bolting and rubber tired haulage.

Jan 1, 1967