Search Documents

By S. Managi, M. C. Williams, N. H. Behling

Particle processing is a key to using solid particles in fuel cell applications. Selectivity with regard to reactivity, impurities, etc. is important feature and the treatment of particle surfaces could greatly impact the performance of direct carbon fuel cells. Solid fuel particles will become increasingly important in the future. Present energy conversion systems for solid fuels are too inefficient. New energy conversion systems for solid fuels with higher energy conversion efficiencies are possible. Fuel cell technology is a key-technology in these new conversion systems. The direct carbon fuel cell (DCFC) operates on carbon particles obtained from a variety of solid fuel feedstocks. The DCFC is the only fuel cell designed to directly oxidize carbon particles in a special anode chamber. The particles are generally graphite structure with high purity. The electrolyte used is the high temperature solid oxide, molten carbonate or hydroxide electrolyte. Since a pure stream of CO2 is produced the stream can easily be sequestered and disposed. Pure carbon dioxide produced as a by-product would also have a market in many industries. A well-defined technology roadmap identifying key research and development (R&D) issues is necessary to provide a framework for the development of these systems and to prevent entrenchment in inherently inefficient technologies. This review paper describes the direct carbon fuel cell and its system, how it works, the developmental status, the characteristics of the carbon particles needed, and the research and development issues for the technology. INTRODUCTION The DCFC has been under development for many years. It was researched as early as 18961), but an intense research and development is necessary to realize its potential. William W Jacques, a US electrical engineer and chemist, described a DCFC in 1896 in US Patent 555511 for a “Method of converting potential energy of carbon into electrical energy”. Jacques used coke electrodes in a molten NaOH electrolyte. Molten carbonate fuel cell (MCFC), solid oxide (SOFC) or hydroxide electrolyte (AFC) technologies can be used as the basis for the DCFC technology. A schematic of the direct carbon fuel cell in the MCFC mode is shown in Figure 1. The molten carbonate fuel cell operates at approximately 650°C (1200°F). The high operating temperature is needed to achievesufficient conductivity of the carbonate electrolyte, yet allow the use of low-cost metal cell components. A benefit associated with this high temperature is that noble metal catalysts are not required for the cell electrochemical oxidation and reduction processes. For the hydrogen reaction the half-cell electrochemical reactions are

Jan 1, 2019

In 1981, North American Degerstrom Contracting began gold mining on the Little Rocky Mountain Range, near Zortman, MT. In the past four years, the price of gold has fluctuated from a high of $16/g ($500 per oz) to a low of $9.60/g ($300 per oz). With that kind of a moving target, profitability presents a management challenge. Based in Spokane, WA, Degerstrom employs 85 people at the mine. It is one of the largest heap leach operations in the nation. Last year, 8 Mt (9 million st) of low-grade ore was moved to the leach pads in a two-shift, five-day operation. The current pit being worked produces 218 kt/m (240,000 stpm) of leaching ore. Ore fragmentation critical The gold bearing ore has no defined patterns or seams. It is an igneous intrusion resulting from volcanic activity. It occurs spontaneously throughout the range. To recover the gold, areas are staked out and core samples are taken and analyzed. These data determine if the ore is rich enough to mine. Once mining begins, an average of 150 holes are drilled and blasted on a two-day rotation. Five Ingersoll-Rand T4s drill on a 4- x 4.5-m (14- x 15-ft) spacing to a 7.6-m (25-ft) depth. "When we first came to this site, we drilled on a 3.6- x 3.6-m (12- x 12-ft) pattern," said Paul Baker, superintendent for N.A. Degerstrom Contracting. "We did some experimenting using a high density emulsion in the bottom of the hole and filling the rest with regular Anfo." The high density emulsion saved the company on overall drilling and blasting costs since the holes could be spaced on a wider pattern and still achieve the high degree of fragmentation needed for leaching. Blasting is important because the gold lays in the natural strata of the rock. Also, the ore is not crushed before it goes to the leach pads. So complete fragmentation is critical. Terrain dictates loading/hauling system The shot ore is worked in 6 m (20 ft) benches by two Caterpillar 245 front shovels equipped with 3 m3 (4 cu yd) buckets, a 992C wheel loader with a 12.6-m3 (16.5-cu yd) bucket, and a 988E high lift fed by a D9H. A Caterpillar D10 tractor trap dozes to the loader. According to Baker, the 6 m (20 ft) bench is an efficient lift for the front shovel and the wheel loader. In tight quarters or in a pocket of ore, Degerstrom uses the 245s. For high production areas, the wheel loader is used. The hauling fleet includes 28 Cat 773 off highway trucks. The 45 t (50 st) trucks are seven pass loaded by the 245s with a 25-second cycle time per bucket load. The 992C loads the trucks in two passes in less than 30 seconds. The cycle time is four to five minutes for a 1.2-km (4000-ft) haul on grades that average 10%. Grades, in some places, exceed 16%. "We use the 773s because they have a low weight-to-horsepower ratio - that's what you need in steep country," Baker said. The trucks haul the shot ore to the leach pad. Currently, Degerstrom is working a pad that has a capacity for 5 Mt (5.5 million st) of ore. Building the leach pads The base of the pads resemble a large drainage basin. They take about one month to construct. A 0.3-m (1-ft) layer of impervious bentonite clay is hauled in and leveled by a Cat D9H tractor. A 30-mm (1.2-in.) PVC liner is then laid in place on top of the clay base. It, in turn, is covered with tailings from an old on-site mill. Degerstrom uses the tailings to protect the liner from tears when the ore is dumped. The ore is leveled and built up in 9 m (30 ft) lifts by the D9H. The tractor rips the top layer. Then, a network of plastic irrigation pipe is put in place to distribute a cyanide solution over the surface. The leaching solution percolates through the ore and dissolves the gold. The solution drains from the pads and is pumped to a 22.7-ML (6-million gal) pregnant solution holding pond. The liquid then goes through two separate filtration units. One unit removes entrained solids and the other side adds a zinc dust to precipitate the gold. This is collected on filters. The affluent then returns to a solution holding pond for redistribution through the pipeline network. Typically, 80% of the pad's potential recovery takes place in the first 30 days of leaching. The process stops when the ambient temperature falls below the cyanide's freezing level. And each pad has a leach cycle of four to five years before recovery values decline to a point where further leaching becomes uneconomical. At Zortman, it takes 9 t (10 st) of ore to produce 31 g (1 oz) of gold. It is therefore critical to keep total production costs down and efficiency high.

Jan 1, 1986

By Steve Kral

"The mining industry is a tough business. The obstacles faced in attempting to run a mine - much less build a new one - go beyond an orebody’s geology. There was a time when commodity prices dictated whether or not to build or expand a mine. Today, though, the challenges faced by miners include social responsibility, environmental regulations and a myriad of needed permits on several governmental levels that every miner knows will be challenged by opponents every step of the way. With all of those challenges, and others not mentioned here, it’s a wonder anyone would stay in the industry. But they do. In fact, more than 2,100 mining professionals from around the world gathered in Reno, NV last December for the American Exploration and Mining Association’s (AEMA) annual conference. That is an impressive number, considering that commodity prices remain in the doldrums, preventing companies from building many new mines and limiting expansions at existing ones. Even so, attending such a conference allows these mining industry pros to learn new and more efficient ways to operate their mines and plants through the dozens of technical presentations the conference offered. And mingling with their peers provided another avenue for learning. The AEMA conference also attracted many of the industry’s leading equipment and service providers (228 exhibitors in 246 booths). Technical presentationsThe AMEA meeting is known for its variety of high quality technical presentations and the 2014 conference was no exception. Some of the topics include new technologies in surface and underground mining, explorers and emerging producers, mine closure and remediation, regulations and reserves reporting, hydrology and new innovations in mining. Here is a sample of some of the presentations."

Jan 1, 2014

By George A. Roche

Since our firm was established by Mr. Price in 1937, we have followed an investment philosophy which is based on the belief that investment in growth stocks is the most assured way of achieving superior, long term investment accomplishment. There are many criteria that we use to select growth companies but the most important is a combination of superior management operating in an industry with above average growth potential. This growth stock approach is the cornerstone of our investment strategy for two of the three mutual funds sponsored by the Price organization and for our private clients. However, during the past 5 years we have seen inflation accelerate due to a variety of factors including the inability of our government to meet seemingly unlimited needs with limited revenue sources. While there might be temporary periods of price stability, we believe that inflation will still continue to be the investor's greatest problem in future years. Our conviction that inflation would increase combined with the acceleration of inflation in the late 1960s stimulated an intensive investment research effort, on our part, to identify those companies with strong natural resource bases -- who own or control large, secure, and low cost tangible assets. Over the longer term and in an environment of a depreciating dollar some of these firms should be able to develop and sell these assets at higher prices. While we still believe that investing in growth companies is a sound investment strategy to offset inflation, we also believe that certain natural resource companies will show well above average investment performance. In the newest Price mutual fund, The Rowe Price New Era Fund, we have, as a matter of policy, placed a large portion of the portfolio in natural resource companies.

Jan 1, 1972

By M. W. Buche, E. Tarshizi, R. Chappidi, B. Inti

"Coal mining is an age-old method of power production in the world. It is also widely known for the associated risks during mining. Although the number of mishaps has dropped dramatically over the years, the number of fatal accidents is still a concern, and any aid in reducing these figures would be important to industry workers. Therefore, data from accident reports during the past seven years were collected and analyzed. Qualitative data from reports and articles provide a deeper understanding of the incidents, thus affording the possibility of identifying patterns and relationships between the accidents. For this study, a total of 119 fatality accidents occurring in U.S. coal mining operations were analyzed using advanced text mining techniques. The fatality data were obtained from U.S. Mine Safety and Health Admininstration fatalgram reports. This analysis is primarily exploratory in nature and uses term frequencyinverse document frequency (TF-IDF) methodologies along with correlation network plots. An interesting word relation pattern was obtained that identified “positioning” as the common cause of 12.6 percent of accidents, and found that 29.4 percent of accidents can be categorized as vehicle-related. IntroductionIn the mining industry, accidents are situations that employees and employers wish to avoid. They are devastating experiences to the victims and their coworkers alike. Even worse, accidents that result in fatalities create trauma and undesirable repercussions. Several measures have been taken throughout the industry to prevent such mishaps, and the U.S. Mine Safety and Health Administration (MSHA) provides continuous monitoring for miners’ safety by guiding organizations through best practices in every job role. As a result, according to MSHA, there has been a steady decline in the average number of deaths due to accidents over time. Nonetheless, any opportunity to avert one more such casualty is of paramount importance, and that is the goal of our analysis. Our objective is to identify opportunities resulting from previously unexplored directions in order to provide additional insights into potential safety recommendations. Until now, most of the studies in this area had been conducted using structured and tabulated data with a constant number of categorical and numerical variables. Unstructured text data mining is an emerging area that is still insufficiently researched and has a feasible scope for important results, as a vast majority of human communication and cognizance is comprised of words. The aim of undertaking this project by capitalizing on unstructured data is to analyze the text reports to discover potential relationships that explain the causes of accidents in new light in order to mitigate the occurrence of fatalities. The analysis in this project is based on textual data obtained from the MSHA website (2017). Individual accident reports are organized according to the date and year of the fatality. Each report includes details with images of the incident. For convenience, a simplified summary of the report is also available. Data collection consisted of gathering formal documentation of fatal accidents in the coal mining industry during the past seven years. These reports were extracted from the website in text format."

Jan 4, 2018

By William A. Vogely, Lawrence J. MacDonnell

This section begins with an introduction to several key environmental laws. This is followed by a discussion of some of the issues raised by such environmental regulation. Finally the subject of regulatory reform is addressed. Overview of Selected Major Environmental Laws The number, type and complexity of environmental laws and regulations affecting mineral resources development have grown at an astonishing rate since the 1960s. The most significant laws and regulations are those addressing the use of the public lands; those concerned with air quality, water quality, and surface reclamation; and those defining government responsibility for its actions having important environmental consequences. The laws and regulations governing activities on the public lands will be taken up in the section 5.15C, "Minerals and Land Management." In this section we will concentrate on five primary laws: the Clean Air Act, the Clean Water Act, the Surface Mining Control and Reclamation Act, the Endangered Species Act, and the National Environmental Policy Act. The Clean Air Act: The legislative and regulatory framework for controlling air pollution has developed in a series of steps. Most important for present purposes are the Clean Air Act of 1970 (P.L. 9 1-604) and the 1977 Amendments (P.L. 95-95). The rather complex air quality control scheme includes four key elements-national ambient air quality standards, state implementation plans, the prevention of significant deterioration program, and the non- attainment program. National Air Quality Standards. The 1970 Clean Air Act is a landmark law because it contains the first explicit recognition that pollution is a nationwide problem requiring a national control program. The federal government through the Environmental Protection Agency (EPA) was to establish national air quality standards for at least the six pollutants named in the Act (sulfur dioxide, carbon monoxide, total suspended particulates, photochemical oxidants, hydrocarbons, and nitrogen dioxide). These standards were to be established so as to protect public health, "allowing an adequate margin of safety." The cost of achieving these standards is not to be considered. The 1970 Act unrealistically required that these standards be achieved in all areas of the country by 1975. As the program has developed, the air quality control regions are now to be designated as "attainment" or "nonattainment" with respect to each of the national standards. State Implementation Plans. Under the Act the states are given the primary role in achieving the ambient standards. States are to develop and implement control plans governing emissions from all existing and new sources. These plans can include emission limitations for existing stationary sources, transportation control plans to reduce emissions from mobile sources, and pre- construction review of new stationary sources to assure compliance with new source performance standards. The EPA must approve all state implementation plans. Sanctions are given to the EPA to be applied if states fail to submit acceptable

Jan 1, 1985

By T. BACHMANN, G. SHAPLAND, E. Amini, N. BEATON, M. BECERRA

In this study, several methodologies to manage low grade and often competent portion of the ore have been proposed and tested in lab, pilot and operational scales. Relevant to this subject, the Cooperative Research Centre for Optimising Resource Extraction (CRC ORE) has developed Grade Engineering® (GE) concept to modify feed streams by rejecting the low grade and possibly hard components in the stream at the early stages of a value chain. Application of GE requires to understand the impact of the process on the value chain as they are value modifiers on in situ opportunities. Traditional modelling approaches and tools do not have the ability to run the analysis in a block model scale with high fidelity in an integrated value chain. Integrated Extraction Simulator (IES) in conjunction with sophisticated analytical tools such as a neural network (NN) was used to develop and reconcile a fully integrated value chain. The value chain model makes it possible to run all available blocks in the Geomet block model, which could be several millions, under possible scenarios for Grade Engineering for economic evaluation analysis and mine planning.

Sep 16, 2020

By Steve Trussell, William H. Langer

"Arizona aggregate (sand, gravel and crushed stone) producers enjoyed more than a half a century of nearly constant growth in demand for aggregates. Approximately 80 percent of the aggregate produced in Arizona is sand and gravel, and 20 percent is crushed stone (U.S. Geological Survey, 2015). Figure 1 shows the generalized distribution of potential sources of sand and gravel (yellow) and potential sources of crushed stone (other colors described below). Black dots show locations of aggregate operations.Sand and gravel commonly is produced from modern river channels and terraces although some alluvial fans and high-level paleo-river terraces also serve as aggregate resources. The gravel clasts are a mix of rock types that reflect the types of rock in the source area of the rivers. Generally processed river gravels meet stringent specifications for highend uses.Crushed stone, which makes up about 20 percent of production, primarily comes from a variety of metamorphic rocks and light-colored intrusive igneous rocks such as granite (brown areas), dark colored extrusive igneous rocks such as basalt and scoria (rust colored areas), and carbonate rocks such as limestone or dolostone (green areas). Carbonate rocks are also used in the manufacture of cement and lime.Construction and aggregate production in ArizonaBecause aggregate producers have limited facilities for storing product, stockpile changes are insignificant compared to production. Therefore, demand or consumption of aggregate in Arizona is considered to be equal to production. Production figures used in this paper reflect shipments, sales or marketable production, including aggregate used by producers to make readymix concrete and asphalt. Production figures were reported by the U.S. Bureau of Mines from 1950 until 1995 and by the U.S. Geological Survey (USGS) since then. Production figures are reported voluntarily, and major operators are the primary source for these figures. Because many smaller operators do not report their production, the figures are conservative values that provide an approximation of aggregates production activity."

Jan 1, 2015

"Above ground, elevated belt conveyors with span >200m between support points can cross valleys, rivers, forests and buildings with minimal footprint. The Cable Bridge Conveyor is a new type of suspension bridge based belt conveyor system that has long span between support points. It combines typical belt conveyor and the improved simple suspension bridge to form a conveyor bridge. The improved simple suspension bridge places a widened bridge deck directly on suspended cables, without the need for high truss towers. The benefits include reduced cost and increase aerodynamic stability compared to conventional suspension bridges. The Cable Bridge Conveyor’s compatibility with current belt conveyors allows the versatility in application. INTRODUCTION Belt conveyor is a ubiquitous material handling system. Conveyors can be placed directly on ground or elevated above ground by support structures. Considerations of cost, design, environment, civil work, safety and process requirements are all factors in choosing the ground based or elevated conveyors (1). The ground based conveyor has the lowest structural cost, where the conveyor is laying on an existing road. Maintenance access is easy and straight forward. Compared to the ground based conveyor, the elevated conveyor can cross existing buildings and structures, give passage to traffic beneath the conveyor, has smaller footprint, and requires less civil work to pass mountainous areas. The drawback of the elevated conveyor is higher structural cost, which can be compared with savings in civil work and other benefits. Conventional elevated conveyors are supported by rigid truss type structures, with typical span of 15m to 25m between concrete support bents or steel trestles. Triangular truss, using steel pipes instead of hot rolled steel sections, is more efficient. The typical span of triangular truss supported conveyor is around 30m to 40m, while the weight is about 10% less than conventional box truss with shorter span (2). Long span elevated structure based on suspension bridge is another step forward in increasing the distance between support bents, reaching 100m~400m and beyond. The very wide distance between support points of an elevated conveyor offers unique benefits. The conveyor can cross rivers, valleys, highways, forests and other obstacles with minimal footprint and reduced civil work. The versatility from long span conveyors makes bulk material transportation over previously impossible terrains now a feasible option."

Jan 1, 2015

By VÍCTOR VÁZQUEZ-VÁZQUEZ, GUILLERMO TIBURCIO-MUNIVE, María M. Salazar-Campoy, JESÚS L. VALENZUELA-GARCÍA, OFELIA HERNÁNDEZ-NEGRETE

This study examines a process for the recovery of precious metals from difficult minerals that exhibit refractory characteristics to cyanidation: low extraction of metals and high consumption of leaching reagent. A mineral sample from Monte del Favor Mine, located in Hostotipaquillo, Jalisco, Mexico, was physically and chemically characterized by X-ray powder diffraction (XRPD), scanning electron microscopy (SEM), energy-dispersive X-ray spectroscopy (EDS), fire assay and atomic absorption spectroscopy (AAS). Two stages of leaching were carried out, first to eliminate manganese from the sample using sodium sulfite (Na2SO3) as a reductive reagent along with sulfuric acid (H2SO4), and second to dissolve gold and silver with hydrochloric acid (HCl) and sodium hypochlorite (NaClO). The results show extractions of around 96 percent for manganese (Mn), 98.73 percent for silver (Ag) and 83 percent for gold (Au). The usefulness of high acidity and Na2SO3 to obtain better results in Mn and Ag leaching are discussed along with the roles that HCl and NaClO play in Ag and Au dissolution values.

By D. Tepavac, S. Simmonds

"The high virgin horizontal in situ stress field in the Sydney Basin and its impact on civil engineering projects is a well-known and accepted phenomenon found in significant literature (e.g., Pells, 2013). The prevailing high-stress effects depend on many factors — rock quality, tunnel orientation, proximity of geological features to tunnel crown, size and shape of opening, depth of excavation and stress magnitude. The behavior of the rock mass under high in situ stress conditions can cause stress fracturing and consequent dilation of the tunnel periphery, resulting in rock spalling at the tunnel crown/ invert or raveling of rock blocks on the tunnel sidewall. This type of failure is of a brittle nature and may create construction and safety risks during tunnel excavation, if it occurs behind the excavation face where ground support has already been installed. Therefore, the associated risks need to be managed during construction. This paper presents the design strategy adopted to mitigate these adverse tunneling conditions for the WestConnex Project to-date. Overview of the WestConnex M4 East and new M5 tunnel projectsWestConnex is one of the New South Wales government’s key infrastructure projects. This 33 km (20.5 mile) project aims to ease congestion and connect communities and is the largest integrated transport and urban revitalization project in Australia. It was a key recommendation of the State Infrastructure Strategy released in October 2012. It brings together a number of important road projects, which, together, form a vital link in Sydney’s Orbital Network. These road projects include a widening of the M4 east of Parramatta, a duplication of the M5 East, and new sections of motorway to provide a connection between these two key corridors. The WestConnex project includes a number of stages: Stage 1a: M4 Widening; Stage 1b: M4 East; Stage 2: New M5; and Stage 3: M4–M5 Link. The tunnel design referenced in this paper relates to Stage 1b and Stage 2 of the WestConnex Project (Fig. 1)."

Dec 1, 2018

By S. Chander

The mechanism of oxidation of sulfur in pyrite is a function of the rate and driving force for oxidation. New evidence is presented in this article to show that at moderate potentials, a sulfur-rich hydrophobic layer is formed. Under ordinary conditions, the sulfur layer is covered with a layer of iron oxides, hydroxides, sulfate or oxy-sulfide ions. Under these conditions, pyrite is hydrophilic. In the presence of iron-chelating agents or iron sequestering ions, iron layer might not form. Under these conditions, sulfur-layer is exposed and pyritic might become hydrophobic. Stronger oxidizing conditions decompose the sulfur-layer, thereby making the surface hydrophilic.

Jan 1, 1992

By R. E. Cook

"Mineral deposits require substantial amounts of energy to transport and be processed into usable form and, as such, present a real processing challenge in that the deposits are never homogeneous and orebody compositional characteristics are all over the map. Extracting the desired mineral(s) from the deposit at sufficient profit margin, despite severe fluctuations in market price, requires process automation architecture capable of supporting an integrated enterprise solution. Such an architecture will encompasses the activities of individuals, process units, process areas, plant level activities, mine management and business planning, and accounting systems. Key to the automation process is the aspect of value generation. This article brings together the various requirements for the automation of a mining enterprise and presents the different aspects of how to obtain value across the entire mining operation.Minerals’ processing sites are historically long lived, with 20-year life-of-mine not uncommon and 75 years not unheard of. Considering that hardware technology advancements are introduced every six months, or less, it is prudent to select process automation systems that adhere to “open” industrial standards versus proprietary based systems. In the minerals processing industry, the key to survival is driving the cost of production per unit volume to the lowest possible level and provide enough profit to sustain operations. Control system architecture and business information technology are rapidly becoming important tools in the quest for productivity. Getting key dynamic business performance information at the right time to the right person or process unit is crucial to successfully achieving corporate goals. The process automation architecture selected must, therefore, be able to integrate to the various networking enterprises and business systems.The mining industry is generally known as an extractive industry that is physically oriented with respect to operations and the activities in which workers engage. Large numbers of people performing manual tasks in difficult surroundings, produce variable outputs. But times are changing – and so are industry best practices. While the nature of work still consists of activities such as ore extraction, ore movement, ore concentration, refinement and logistics, automation innovations are starting to change the nature of many of the production steps. The industry has transitioned from requiring more physical activities by workers to more information management, automated control and collaboration within the operation. Humans are good at situational intervention and nonlinear reasoning and do best when empowered with an overall production perspective. Machines and automation are good at repetitive functions, steady state operation, and managing transitions. Thus, a combination of advanced technology solutions, reliable and useful information and full human contributions are necessary to mining operations for value generation."

Jan 1, 2015

By H. M. Park

Risk is a major factor in all mining activities, arising from many internal and external variables. The authors? research has resulted in a systematic method for the quantification of risk in mining projects (Park, 2012). This is the second part of a three-part series. The first part was published in the October 2013 issue of Minining Engineering magazine and can be found here at www.me.smenet.org. This paper discusses methods of assessing the overall risk associated with those variables, and presents a statistical model based on a survey of 31 experts. The third paper, to be publised at www.me.smenet.org on Oct. 14, presents an evaluation of the statistical model, using data from previous mining investment decisions in which the authors have been involved.

Oct 1, 2013

By Louis H. Meece

The romance of the River lives on in the tales of Mark Twain; and many Americans still think of the Mississippi River in terms of the steamboats loaded with passengers, gamblers and cotton. Yet for many years, coal has been a major cargo on the American waterways. Currently, about 100 million tons a year of coal is handled in some part of its journey from mine to destination by barge. The bulk of this traffic has been on the Ohio River System and the Upper Mississippi River System in years past. Now we have a new entry. Over the past 10 years various movements of coal have developed down the Mississippi River to power plants at Memphis and along the Gulf Coast, and a small amount of metallurgical coal has moved down the Mississippi River for export to Japan since 1970. But in 1980 a brand new player came on the scene. 1980 was a momentous year for the American coal business. Historically, we have exported about 50 million tons a year of metallurgical coal to the world's steel mills. Just before and after World War I, we also had a fairly healthy export trade in steam coal; and again in the late forties, we supplied large amounts of coal to Europe until domestic production could recover from the ravages of World War II. But since the early fifties, the name of the export game has been metallurgical coal. Starting in the mid seventies, something began that was almost totally missed by the American coal industry; and that was the growth in the use of coal first in Europe and now in the Far East as a steam product and as an alternative to petroleum products. As these world coal markets began increasing, the U.S. at first was thought to be noncompetitive because ocean rates were still very low. For example, as recently as 1977, Australian coal could be moved all the way from Australia to the Gulf Coast for $12.50 per metric ton. Coal exporting countries were Poland, Australia and South Africa, except for the continuing exports of U.S. high quality metallurgical coal. But then came the second oil shock, and all of the sudden that $12.50 rate from Australia to the U.S. Gulf became $25.00. And then suddenly and almost unrecognized by the American industry, American coal was in fact competitive at overseas destinations because of the drastic change in trade patterns brought on by the doubling and tripling and quadrupling of bunker fuel prices for ships.

Jan 1, 1982

By Manoj Kumar, Anil Kumar Singh, Prabal Patra, Ashish Agrawal, Souvik Ghosh, Subhashis Kundu, Kamma Ramakrishna Rao, Manish Kumar Gupta, Anindya Sarkar

The slag measurement systems in the cast house are very important. In the conventional method, the slag is granulated in a slag granulation system, and the slag flow rate is measured by the associated belt scale. However, in places where a slag granulation system is not available, the alternate approach is to deduce a theoretical calculation and develop the measurement because the commissioning of such slag granulation requires huge capital and has inherent geographical limitation. However, the theoretical approach suffers from several drifts and is far from the reality. In the present paper, we have innovatively engineered a sensor by designing the stellite-coated thermocouple that can measure the temperature of the slurry and placed it in such a way that the abrasive slag granules do not obstruct it, but we could measure the temperature of hot water, and further based on the thermodynamic approach, the slag flow rate is determined that can be compared with the theoretical approach. This approach of slag rate measurement is cost-effective and long-lasting.

Oct 2, 2023

By David F. Becker

Two-dimensional, finite-difference elastic modeling aids in planning an optimum seismic-acquisition scheme to define the extent of subsurface cavities resulting from in situ gasification. To understand the seismic effects of a cavity, two models are compared and contrasted. Model A consists of a low-velocity layer (LVL) in a half space; Model B contains a rectangular water-filled cavity in the LVL. Amplitude differences are the dominant effect on the surface records for each model. Cavity resonance and diffraction effects are more definitive in vertical seismic profiles (VSP's) and in a "snapshot" of the wave field. Interpretation and subtraction of corresponding records for both models shows the need for pre- and post-gasification seismic recording. Also VSP data are more informative than surface records.

Jan 1, 1983

By M. C. Mound

A recent development using XRD techniques, a unique fixed detector, specifically permitting full mineralogical information simultaneously for the first time, specially designed sample preparation and presentation system and Rietveld codes provide a continuous real- time analysis on the true contained mineral polymorphic composition of powder streams such as ore materials, cement, ground clinker or any other mineral stream conducive to XRD analysis. There are several COSMA systems currently operating in the US, Canada, Italy and Australia, proving service and reliability of this concept. The mineralogical information generated continuously in real time is used for automated efficiency, product quality and reduces costs. Quantitative Phase Analysis information is transmitted to the plant DCS via Modbus over RS422 or ethernet. Some limited information is stored in the on-board computers for optional future use at the operator?s option.

Jan 1, 2010

By Justin R. Patts, Andrew B. Cecala, A. KYLE LOUK, Emily J. Haas

The U.S. National Institute for Occupational Safety and Health (NIOSH) and the former U.S. Bureau of Mines (USBM) have put significant effort over the past four decades into researching and developing engineering controls and interventions to reduce mine workers’ dust exposures during the bagging and palletizing of industrial minerals. Workers who perform the manual bagging and palletizing of 50- to 100-lb bags typically have some of the highest dust exposures of all workers at mining and mineral processing operations. This paper provides an overview of available dust control technologies for bagging operations and presents the findings of a recent case study conducted at four industrial sand operations to identify the current types of bagging and palletizing technologies being used and to evaluate their effectiveness in reducing workers’ exposures to respirable crystalline silica dust. An evaluation is also performed to determine if further reductions in respirable dust levels can be achieved by incorporating additional modifications or improvements into the existing technology.

By P. C. Cochrane, I. S. Clelland, S. H. E. Phillips

Geological and hydrological conditions in the strata overlying the Salado Formation vary considerably in the Carlsbad, NM, area. The first four shafts sunk at International Minerals and Chemical Corp. (IMC) property have been located in competent and essentially dry conditions, while other shafts on adjacent properties have had such adverse conditions that ground freezing has been chosen as the water and ground control technique for shaft sinking. At the location of the IMC No. 5 shaft there has been extensive erosion and salt dissolution in the Rustler Formation, leading to collapse of some zones of the strata. Both ground freezing and pregrouting were considered as alternative methods of stabilizing the extremely poor ground conditions and controlling the potentially very heavy water inflows. It was decided that pregrouting the shaft was feasible and would offer substantial cost and time saving over a ground freezing technique. This paper describes the pregrouting techniques used and illustrates the requirement for flexibility in a grouting program so that it can be modified to reflect any new or additional information obtained during the progress of the grouting.

Jan 1, 1987