Search Documents

By Robert R. Munro

Traditional aggregate sources, that is the riverbeds, the alluvial fans, located relatively close to the developing urban centers are being foreclosed to mining. As the sand and gravel reserves are depleted, those production plants are unable to secure additional adjacent reserves and are being forced to close down. The sand and gravel industry, in many respects, is its own worst enemy. We promote development, we promote the paving of streets, the building of houses, and industrial and commercial centers, and because of economics, we tend to favor those developments located close to our operations. Thus, we encourage development by our neighbors who soon become our detractors. In general, urban development is not compatible with sand and gravel mining. The neighbors don't like the view of the pits or the quarries, they complain about the "dust", about noise, about trucking . . . in general, the neighbors are not happy being close to an aggregate source.

Jan 1, 1984

By J. F. T. Agapito

Two flat-lying trona seams 3-to 3.5-m thick, approximately 10 m apart, and at depths of 250 m are mined by room-and-pillar at OCI's Big Island Mine in Wyoming. Continuous miners and a yielding pillar system have contributed to improvements in resource recovery and productivity. Long-term stability with minimal subsidence is needed for a large portion of the mine beneath the Green River channel. This was investigated by computer modeling in 1990. Although results of the study indicated good long-term stability, recommendations were made for stress determinations to verify the model. Stress determinations made in 1997 showed pillar stresses 10% to 20% higher than the model stresses, and barrier pillar stresses 10% to 15% lower. This implies that higher panel stresses will be transmitted from the upper to the lower seam. A stability evaluation of the lower seam is planned before two-seam mining to assess entry widths and support requirements.

Jan 1, 1999

By Bruce K. Cantrell

As part of a continuing study of diesel exhaust aerosol characteristics, the Bureau of Mines has applied Chemical Mass Balance (CMB) model source apportionment analysis to evaluate a size selective sampling method for determining the separate diesel exhaust and coal dust aerosol concentrations in a diesel equipped coal mine. Size selective sampling was used under the premise that diesel exhaust aerosol dominates the submicrometer aerosol size range, while most of the mineral dust aerosol is greater than 1 m. A micro-orifice, uniform deposit impactor (MOUDI) was used as the size selective sampling method. Concurrent samples of mine aerosol were collected using a dichotomous, respirable aerosol sampler. This sampler separated the fine and coarse size portions of its sample at 0.7 m. Trace element concentrations for in-mine aerosol sources and the dichotomous samples used by the CMB model were measured using Instrumental Neutron Activation Analysis. The CMB analysis, applied to both the fine and coarse fractions of the respirable mine aerosol, yielded the mass concentration contributed to each by diesel exhaust and mineral dust aerosol sources. The MOUDI size distribution data were analyzed using nonlinear regression to parameterize the fine and coarse fractions of the sampled aerosol and to estimate the contributions to each fraction from both coal dust and diesel aero- sol sources. For the diesel mine visited, analysis of the MOUDI samples yielded a value for the fraction of the fine aerosol attributable to coal dust of 15[]7% fine fraction coal from analysis of the MOUDI samples versus 25[]4% from the CMB analysis. The remainder of the fine aerosol in the mine was diesel exhaust aerosol. CMB analysis confirms the original premise for such sampling. After correcting for the presence of coal dust in the fine aerosol fraction, analysis of the MOUDI size distributions yielded estimates of respirable mineral and diesel exhaust aerosol concentrations that were accurate to with-in 10% of values determined by the CMB apportionment.

Jan 1, 1987

By R. Bruce Sheibach

The Picher Mining District, located principally in north-eastern Oklahoma, was one of the world's largest lead-zinc mining areas during its 55 year life. The field covers an area of approximately 72 square miles (186 km.-); an estimated 1.6 x [103 yds3 of material (1.22 x 103m3)] worth in excess of one billion dollars, has been mined. Mining activities were typified by surface exploratory drilling identifying ore distribution and extension of underground workings to the lead and zinc deposits outlined. Exploration holes were either left unplugged or plugged at the surface with a section of a telephone pole. Low grade ore and waste rock were discarded in mined out portions of drifts. These waste piles containing pyrite and marquisette were left underground and oxidized during the many years of active mining. Upon cessation of mining activities in the mid-1960's, the drifts and shafts of the abandoned workings began to flood as the cone of depression filled in, leading to the dissolution of the oxidized sulfides and the formation of large volumes of acid mine water in the mined out openings. The resulting poor quality water, with high concentrations of cadmium, iron, lead and zinc, began discharging at the surface in 1979. Contamination of the underlying aquifer supplying local residents was first detected on a localized scale in 1980. The present surface water and ground water contamination have lead to the area being classified as one of the top ten hazardous waste sites in the U.S. by the EPA under the superfund program.

Jan 1, 1982

By Chee Theng

The Mineral & Metallurgical Processing Division (MPD) of the Society for Mining, Metallurgy & Exploration held the 13th MPD Student Poster Contest on March 1, 2023, during the MINEXCHANGE 2023 SME Annual Conference & Expo. The event showcased the work of 24 graduate and undergraduate students from U.S. and international institutions. The contest began in January when the students submitted one‐page abstracts for judging. In February, they prepared and presented posters that explained their research, and each student had five minutes to showcase their research to a panel of judges during the conference. In recognition of their efforts, the MPD provides monetary rewards to all participants. For graduate students, first place receives $1,000, second place $500, and third through seventh places $200 each, and for undergraduate students, first place receives $1,000 and second place $500. The main authors of nonplacing entries receive $125 each. Participation in the contest also includes a free ticket to the MPD Luncheon, where the winners are announced.

Nov 28, 2023

By R. K. Mehta

Stirred ball mill feed used for ultra-fine grinding application requires fine size separation step in order to avoid over-grinding. This paper presents the selectivity curves obtained for oil shale and complex sulfide are using 460 mesh (30 micron) Derrick vibrating screen. Interestingly, the selectivity curves generated from the experimental data were monotonic increasing selectivity for oil shale but not monotonic increasing for sulfide ore. These non-monotonic increasing selectivity curves were similar to the mechanical air separator fishhook selectivity curves described by Luckie and Austin. A 2 stage classification in series model describing the fishhook selectivity curve has been used in proposing the classification mechanism for fine vibrating screens when heterogeneous multicomponent sulfide are undergoes size separation.

Jan 1, 1992

By R. A. Pimentel

Complying with reduced dust standards (i.e., less than 2.0 mg/m3) due to quartz levels that exceed 5 percent is presently a critical problem for many continuous mining sections. Results are presented of research which was performed to determine the factors causing high levels of respirable quartz dust and to identify the major contributors to operator exposure. It was found that the significant sources of quartz dust are the drilling of the roof and the mining of the roof, floor and rock bands. Both the miner and the bolter may be on a reduced standard, but compliance is easiest to achieve on the bolter for which improvements in maintenance and operator practices are usually sufficient. At the miner, the problem is more elusive. Research continues to identify operating and mining practices that contribute to the exposure..

Jan 1, 1985

By Brian V. Roulston

Potash is Canada's leading industrial mineral in terms of value of production, with 11.1 M tonnes of muriate of potash produced in 1992 for a value in excess of $1 billion U.S. Each tonne of potash produced generates about 2 tonnes of waste salt, together with slimes and brine. The disposal of these waste products, particularly the salt and slimes which are discharged on the surface, has recently become an environmental concern. This concern is forcing companies and regulatory authorities to review disposal practices. In New Brunswick, on Canada's east coast, Potash Company of America operates a mine at which 2 M tonnes of potash ore and 0.5 M tonnes of rock salt are mined each year. The mine is situated in an environmentally sensitive area, noted for its dairy farming and salmon angling. In such an area it was recognized that the storage of waste on surface would be unacceptable, and the mine was designed around this principle. Three main waste streams - salt, slimes, and brine - must be managed as an integral part of the mining system. Around 1.5 M tonnes of fine salt tailings from the milling process and the rock salt screening operation, are sent directly to the active cut-and-fill potash stopes to be used as backfill. Slimes and excess brine from the mill are piped underground as a slurry to be discharged into one of the basin shaped stopes created by mining of the rock salt. While the slimes settle out, the clarified brine is withdrawn from part of the stope to be pumped to surface as a feedstock for the evaporator - a process which recovers the contained potash values in the brine. By designing a system which integrates the mining, processing and disposal of all product streams, and by careful production planning, it has been shown that zero effluent potash mining is possible and points the way for the industry in the future.

Jan 1, 1995

By Karl C. Dean

The current emphasis on environmental problems has focused attention on the massive nationwide accumulations of mine, mill, and smelter wastes that represent potential air and water pollution hazards. The pollution hazards can be reduced or eliminated by utilization or stabilization of these wastes. The U.S. Bureau of Mines, since the inception of the Solid Waste Disposal Act of 1965, has been conducting research to determine the practicality of various utilization and stabilization procedures. Investigations include partial extractions of desirable waste components and full utilization of the wastes as simulated soils or in ceramic or other structural products. Chemical, vegetative, and combined chemical-vegetative methods of stabilization have been actively studied. This report updates information previously developed by the Salt Lake City Metallurgy Research Center and presents the current status of antipollution solid waste work 1/,2/.

Jan 1, 1970

By K. R. Miller

Thunder Basin Coal Company has two mines located in the southern portion of the Powder River Basin. 60-90 km southeast of Gillette, Wyoming. The mines are principally located on federal coal leases acquired in the late-1960's. Development plans for the Black Thunder Mine focused on dragline stripping, but environmental considerations during the mid-1970's made truck-shovel stripping the method of choice when the mine opened in 1976. In 1981, the Coal Creek Mine opened as the first dragline mine in the Gillette area of the Powder River Basin. The regional terrain is flat-lying with occasional clinker-capped hills. The mines are located on the Wasatch and Fort Union Formation contact. The coals are Paleocene in age and the deposits are structurally simple, dipping gently to the west. The seams are thick and are classified as sub-bituminous-C. The Black Thunder Mine, with its 21 m thick seam, is strategically located in the center of the highest heat value mining area of the southern Powder River Basin.

Jan 1, 1993

By A. W. Fletcher

A nickel-copper sulphide concentrate was treated in a pilot plant at Warren Spring Laboratory during 1961, by a hydrometallurgical roast-leach- solvent extraction process devised to cleanly separate the metal values, and produce acid sulphate liquors containing the metals. It is shown that 86 percent of the nickel and 95 percent of the copper could be leached from the calcine, after a sulphatizing roast on finely ground flotation concentrate. Iron was removed from the leach liquor by limestone neutralization with a small loss of values. Copper and nickel were separated by solvent extraction with naphthenic acid in kerosene after partial neutralization of the iron-free liquors with ammonium hydroxide. Hydrogen sulphide and chlorine were used to remove zinc (and residual copper) and cobalt impurities respectively. The recovery of pure copper and pure nickel, by electrowinning, from the acidic solvent extract strip liquors finally produced, appears technically feasible.

Jan 1, 1964

By Abbas Zaidi, Betty L. W. Ou

Wastewaters generated during the extraction of gold from the ore can contain a variety of contaminants such as cyanide, heavy metals and arsenic. Proper management of these wastewaters is therefore necessary to minimize the negative impact of gold mining and milling operations on the environment. The Wastewater Technology Centre (WTC),located in Burlington, Ontario, Canada, has been involved in several studies related to the evaluation of various effluent treatment technologies which are relevant to the treatment and proper management of gold mill effluents. These studies have included bench and pilot scale tests, and the evaluation offull-scale systems. Furthermore, the WTC staff developed protocols for cyanide analysis in gold mill effluents, and a mathematical model for predicting the degradation of cyanide in tailings ponds. The information generated by the WTC staff has been referenced in several reports and papers published over the last ten years (Schmidt et.al. 1982, Simovic & Snodgrass 1989, Whittle et.al. 1989, Zaidi et.al. 1989, Zaidi et.al. 1991). Recently, the WTC has started to develop a micro­computer based expert system for use by decision makers in the gold mining industry and relevant government agencies who are involved in process design, process evaluation, costing, evaluation of the best practicable technology, approval of suggested effluent management systems, and so on. This paper presents some relevant background information and a discussion of the latest version of the expert system being developed by the WTC.

Jan 1, 1992

By V. Anthony Cammarota

MINERALS INFORMATION PROGRAM Mineral data collection by the Federal Government actually began in 1882 with an appropriation by Congress to the U.S. Geological Survey (USGS). Although the Bureau of Mines was instituted in 1910, it was not until 1924 that the collection, interpretation, and dissemination of worldwide information on production, consumption, and availability of minerals became the responsibility of the Bureau. The objective of the Bureau's minerals information program is to maintain and provide reliable, timely, and comprehensive data for analysis of national minerals problems. This program is implemented by a staff of specialists who cover about 100 mineral commodities and the mineral industries of 168 countries. Data are also provided on the minerals industry on the State and county level. The specialists analyze information to identify trends and problems, forecast future U.S. and world supply and demand for the nonfuel minerals, and relate trends and developments to their impact on the domestic minerals industry. Data Sources and Publications The primary sources of data concerning the domestic minerals industry are the companies that produce, use, and trade in these minerals. Approximately 60,000 survey forms are sent to industry, on a monthly, quarterly, semiannual, or annual basis, to obtain the data. Domestic trade data are provided by the Bureau of the Census, U.S. Department of Commerce. Information on mineral developments abroad is developed by Bureau specialists from mineral reports supplied by U.S. embassies worldwide, from primary source documents, from a review of the technical mining literature, and from onsite mine and plant visits in foreign countries. The information is disseminated through a number of Bureau publications: "Mineral Industry Surveys" provide aggregated data on a monthly. quarterly, or semiannual basis to give timely information on the most important mineral commodities. "Mineral Commodity Summaries," published each January, provides preliminary annual data on supply and demand and discusses significant events of the previous year. The final data are published later in the "Minerals Yearbook," which is the definitive historical record for mineral statistics. "Mineral Facts and Problems," an encyclopedic work issued every 5 years, covers industry structure, technology, supply-demand analysis. economic factors, reserves, and forecasts of U.S. and world demand for individual commodities. "Mineral Perspectives" and "Mineral Issues" cover important international mineral developments and significant issues of current U.S. policy as they relate to minerals. Discussions and analyses of mineral trends and developments also appear in other Bureau publications, such as "Minerals and Materials" and "Information Circulars." These publications provide the basis for analysis and policy determinations by the Bureau and by virtually every Federal agency concerned with minerals, defense issues, the national economy, and foreign relations. The data are also used by industry in planning capital investments in mines and processing plants, by financial analysts, by U.S. delegations in their work with international commodity groups, and by a host of other minerals related organizations. Data Bases The data bases used by the specialists for preparing publications or in response to a continuous stream of inquiries include both those that contain individual commodity data from respondents, and those that are summary data bases on production, trade, capacity, employment and a number of other minerals-related items, not all of which are derived from data reported to the Bureau of Mines. The data bases maintained on the mainframes are not accessible by non- Bureau users. A 10-year data base of supply- demand data, published each year as an update of tables that appear for each commodity in Mineral Facts and Problems, is available on a floppy

Jan 1, 1987

By James J. Scott

Three dimensional photoelastic techniques have been developed which provide information on the state of stress at any point in a model investigated. This investigation utilizes these techniques to determine the stress distributions in the pillars and the roof of a room and pillar mine model. Castolite plastic was used for the construction of the model in which a stress pattern was developed by the stress freezing process. Analysis of the stress pattern was accomplished by use of data obtained by observing points in slices from the model with a polariscope and solving data obtained by' the shear-difference method. Slices through the centerline, edge of pillar and centerline of span were investigated. Results of this work provide information on the overall stress distribution on points of stress concentration in compression, shear and tension, show relative magnitude of stress throughout the model and indicate directions of the most important stress values. A generalized roof bolt pattern is developed for room and pillar mines based on the stress distribution. A digital computer was used in the reduction of data and proved to be extremely useful for investigation of this type.

Jan 1, 1963

By Evan Just

?We are certain there is need for research in every phase of mining." This statement by R. M. Crump of the Jones and Laughlin Steel Company (047) paraphrases opinion widespread among mining people. It is undoubtedly true. In preparation for this presentation, 193 organizations were asked to describe their mining research efforts. 60% responded, The meaning of "research" was taken in several different ways. The continual efforts of progressive companies to improve themselves were reported as research. We will call this and any effort to solve specific and immediate problems "practical research". The continuing investigation of subjects of long range interest will be called "basic research".

Jan 1, 1961

By B. C. Lewis

The mining industry has experienced a general trend toward an increasing number of longwall operations, an increasing percentage of underground coal being mined by longwalls, and increasing productivity from the longwalls. Longwall operators have not yet reached a state of mining euphoria. Competitiveness both within the industry and from alternate fuel sources is forcing continued pursuit of higher productivities and lower costs. The following graphics present trends in the industry. Longwall mines, as defined for this presentation, are those reportedly having longwall installations in each of the respective years. Production from both the continuous miner and longwall units is included in the longwall mines. Non-Longwall mines are all other underground mines. Productivity calculations are based on total employee-hours associated with the operation.

Jan 1, 1990

By M. J. Langley

Zinc ores were first discovered in Tennessee in 1856 at Jefferson City where a deposit of oxidized ore became known as the Mossy Creek Mine. From that time until 1913 small scale attempts at prospecting and mining were made in various parts of the district. The actual systematic development of the zinc deposits dates from 1913 when the American Zinc Company started operations at Mascot. Six mines are in operation by three companies and a seventh mine is being developed by a fourth company. The total daily production from the field is 11,000 tons of crude ore, which grades from 3 to 6 per cent zinc. Most of the ore bodies are large and ramiform, resembling asyrmetrical networks in which the ore shoots form channel like branches with areas of non-comercia1 rock, called blank islands. Most of the orebodies are adapted to large scale mechanization.

Jan 1, 1962

By M. Kehnemuyi

The U.S. Department of Energy is charged, by federal law, with the responsibility for developing and implementing programs for long- term storage and terminal disposal of high- level radioactive wastes from both commercial and defense nuclear operations. Approximately 288,000 cubic meters of defense high-level wastes are currently in storage at the government's Hanford Reservation in the State of Washington, the Savannah River Plant in South Carolina, and the Idaho Chemical Processing Plant in Idaho (U.S. Department of Energy, 1980a). High-level wastes from commercial nuclear power production are stored in water pools or basins at various power plant sites. At the end of 1980, approximately 7.460 metric tons of uranium, contained within 28,300 fuel assemblies was in storage at various reactor basins. Although the present inventory of defense wastes are many times larger in volume and in total level of radioactivity than the commercial wastes, in the future, the latter will constitute a substantial quantity of wastes that will have to be disposed of. The present electric generating capactiy of nuclear power plants in the United States is 56.5 Gigawatts-electric (GWe). The amount of spent fuel that would be discharged and accumulated by the year 2000 from these operating reactors would be 38,000 metric tons. With a projected growth of the nuclear industry to 180 GWe in the year 2000, the amount of spent fuel accumulated at the turn of the century could reach 89,000 metric tons of uranium or approximately 318,000 assemblies. In any case, whether one postulates a no growth pattern or one where nuclear power provides its share in the country's electric generating capacity in the next two decades, a means for safe and environmentally accept- able disposal of high-level nuclear wastes must be found. Storage of commercial wastes in water basins, either at reactor (AR) sites or at away from reactor (AFR) sites, and storage of reprocessed defense wastes in surface or near surface tanks is a temporary solution and is not an alternative for permanent disposal.

Jan 1, 1981

By A. F. Grandt

What is prime farmland? Can such land, once it has been strip-mined for coal, be restored so that it will produce corn, soybeans, wheat, and alfalfa? What methods or practices are necessary to bring about restoration within a reasonable time so that crop yields will be equivalent to or higher than those of unmined prime farmland under high levels of management? These questions concerned land use researchers in Illinois as early as 1948 when the Illinois Agricultural Experiment Station experimented with growing cultivated crops on strip-mined land in St. Clair County (1). This research was done almost 30 years before requirements of Public Law 95-87 were passed by the United States Congress and signed August 3, 1977.

Jan 1, 1980

By N. Myung, G. Hwang, H. Kim, Y. Han, S. Choi

"According to research presently being conducted on selective lithium recovery in seawater, inorganic adsorbents with high selectivity and capacity for capturing lithium ions from liquid lithium resources are called lithium ion-sieves (LISs). Their low toxicity, low cost and high chemical stability make LISs suitable for lithium recovery from seawater. In the present study, the ultrathin LMO nanofibers with controlled diameter were successfully fabricated by an electrospinning technique with a hypothesis that greater aspect ratio (i.e., smaller diameter) would lead to the enhanced recovery of lithium ion from seawater. Design of Experiment (DOE) and dimensionless analysis were performed to systematically optimize the diameter and morphology of nanofibers. Several complementary techniques including FE-SEM and XRD were used to evaluate the physical/physicochemical properties of the nanofibers. Lastly, the lithium ion recovery was tested for the nanofibers with different physical properties using lithium ion solution. INTRODUCTION Demand for lithium resources is increasing in many industries across the world.1-2 However, the conventional resources for lithium is very limited, and it even gets worse to secure the resources due to low grade and/or complexity of feed materials. Much effort has been, therefore, devoted to obtaining lithium from aqueous lithium resources. Several methods such as solar evaporation3-4, co-precipitation5, and solvent extraction6 have been proposed for recovering lithium from an aqueous lithium source, but there are limitations on its use; It takes a very long time or conditions such as temperature, pH and Mg/Li ratio are severe. Lithium ion-sieve (LIS) materials are considered as a good lithium adsorbent because of their unique chemical structure that can selectively separate lithium ion from brine and seawater.7- 10 Furthermore, their low toxicity, low cost, and high chemical stability make LIS suitable for lithium recovery from aqueous lithium resources. Spinel hydrous manganese oxide (HMn2O4) derived from spinel lithium manganese oxide (LiMn2O4) after topotactically extracting lithium from the spinel structure by acid treatment is most widely investigated LIS.10, LIS materials have been actively studied in various forms for easy handling and high efficiency (i.e. membrane11,12, foam13-14, granular15,16). Among them, the 1-D nanostructure LIS with high specific surface area is excellent in efficiency.9 In this study, we present the part of our recently submitted work17. Specifically, we fabricated systemically lithium manganese oxide nanofibers with different diameter as a lithium ion adsorbent using electrospinning technique through design of experiment (DOE). Enhanced lithium ion adsorption properties of the HMn2O4 nanofibers with different diameter were investigated in lithium liquid resources."

Jan 1, 2018